For testing compressive and tensile strength of cement, the cement mortar is made by mixing cement and standard sand in the proportions of (A) 1 : 2 (B) 1 : 3 (C) 1 : 4 (D) 1 : 6

For testing compressive and tensile strength of cement, the cement mortar is made by mixing
cement and standard sand in the proportions of
(A) 1 : 2
(B) 1 : 3
(C) 1 : 4
(D) 1 : 6
by

1 Answer

Answer :

Answer: Option B
by

Related questions

Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the rate of (P/4) + 3.0 percentage of water where P is the percentage of water for standard consistency (C) A cube mould of 10 cm × 10 cm × 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Description : Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the ... cm 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Last Answer : Answer: Option A

The proportions of lime and sand in the mortar normally used in brick construction are (A) 1 : 2 (B) 1 : 4 (C) 1 : 6 (D) 1 : 8

Description : The proportions of lime and sand in the mortar normally used in brick construction are (A) 1 : 2 (B) 1 : 4 (C) 1 : 6 (D) 1 : 8

Last Answer : Answer: Option A

Le-Chatelier's device is used for determining the (A) Setting time of cement (B) Soundness of cement (C) Tensile strength of cement (D) Compressive strength of cement

Description : Le-Chatelier's device is used for determining the (A) Setting time of cement (B) Soundness of cement (C) Tensile strength of cement (D) Compressive strength of cement

Last Answer : Answer: Option B

For testing compressive strength of cement, the size of cube used is (A) 50 mm (B) 70.6 mm (C) 100 mm (D) 150 mm

Description : For testing compressive strength of cement, the size of cube used is (A) 50 mm (B) 70.6 mm (C) 100 mm (D) 150 mm

Last Answer : B

For plastering the exposed brick walls, the cement sand mortar should be (A) 1 : 2 (B) 1 : 3 (C) 1 : 4 (D) 1 : 6

Description : For plastering the exposed brick walls, the cement sand mortar should be (A) 1 : 2 (B) 1 : 3 (C) 1 : 4 (D) 1 : 6

Last Answer : Answer: Option C

Soundness of cement is tested by (A) Vicat's apparatus (B) Le-chatelier apparatus (C) Compressive strength testing apparatus (D) None of these

Description : Soundness of cement is tested by (A) Vicat's apparatus (B) Le-chatelier apparatus (C) Compressive strength testing apparatus (D) None of these

Last Answer : Answer: Option B

The strength of brick masonry in 1:6 cement mortar, is (A) 20 tonnes/m2 (B) 40 tonnes/m2 (C) 50 tonnes/m2 (D) 60 tonnes/m

Description : The strength of brick masonry in 1:6 cement mortar, is (A) 20 tonnes/m2 (B) 40 tonnes/m2 (C) 50 tonnes/m2 (D) 60 tonnes/m

Last Answer : Answer: Option C

Le Chatelier apparatus is used to determine which of the following properties for cement A) Soundness* b) Initial setting time c) Compressive strength d) Tensile strength

Description : Le Chatelier apparatus is used to determine which of the following properties for cement A) Soundness* b) Initial setting time c) Compressive strength d) Tensile strength

Last Answer : A) Soundness*

In a mortar, the binding material is (A) Cement (B) Sand (C) Surkhi (D) Cinder

Description : In a mortar, the binding material is (A) Cement (B) Sand (C) Surkhi (D) Cinder

Last Answer : Answer: Option A

When percentage of mica present in sand is large, it (a) Reduces the strength of mortar, or concrete (b) Increases the strength of mortar or concrete (c) Has no effect on mortar, or concrete strength (d) Enhances the strength of mortar, or concrete, but only marginally

Description : When percentage of mica present in sand is large, it (a) Reduces the strength of mortar, or concrete (b) Increases the strength of mortar or concrete (c) Has no effect on mortar, or concrete strength (d) Enhances the strength of mortar, or concrete, but only marginally

Last Answer : (c) Has no effect on mortar, or concrete strength

Plain cement concrete is strong in taking (a) Compressive stress. (b) Tensile stress (c) Shear stress (d) All of these

Description : Plain cement concrete is strong in taking (a) Compressive stress. (b) Tensile stress (c) Shear stress (d) All of these

Last Answer : (a) Compressive stress.

Reinforced cement concrete is equally strong in taking (a) Tensile and compressive stress (b) Compressive and shear stresses. (c) Tensile, compressive and shear stresses. (d) Tensile and shear stresses.

Description : Reinforced cement concrete is equally strong in taking (a) Tensile and compressive stress (b) Compressive and shear stresses. (c) Tensile, compressive and shear stresses. (d) Tensile and shear stresses.

Last Answer : (c) Tensile, compressive and shear stresses.

A thick paste of cement, sand and water is called – (1) Concrete (2) R.C.C. (3) Mortar (4) Kiln

Description : A thick paste of cement, sand and water is called – (1) Concrete (2) R.C.C. (3) Mortar (4) Kiln

Last Answer : (3) Mortar Explanation: Mortar is a workable paste used to bind construction blocks together and fill the gaps between them. Modern mortars are typically made from a mixture of sand, a binder such as cement or lime, and water

A thick paste of cement, sand and water is called (1) Concrete (2) R.C.C. (3) Mortar (4) Kiln

Description : A thick paste of cement, sand and water is called (1) Concrete (2) R.C.C. (3) Mortar (4) Kiln

Last Answer : Mortar

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Description : Slump test of concrete is a measure of its (A) Consistency (B) Compressive strength (C) Tensile strength (D) Impact value

Last Answer : (A) Consistency

A higher modular ratio shows (A) Higher compressive strength of concrete (B) Lower compressive strength of concrete (C) Higher tensile strength of steel (D) Lower tensile strength of steel

Description : A higher modular ratio shows (A) Higher compressive strength of concrete (B) Lower compressive strength of concrete (C) Higher tensile strength of steel (D) Lower tensile strength of steel

Last Answer : Answer: Option B

Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Description : Modulus of rupture of concrete is a measure of (A) Flexural tensile strength (B) Direct tensile strength (C) Compressive strength (D) Split tensile strength

Last Answer : Answer: Option A

Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Description : Allowable shear strength of concrete, depends upon (A) Shear strength (B) Tensile strength (C) Compressive strength (D) None of these

Last Answer : Answer: Option A

Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Description : Compared to mild steel, cast iron has (i) High compressive strength (ii) High tensile strength (iii) Low compressive strength (iv) Low tensile strength The correct answer is (A) (i) and (ii) (B) (ii) and (iii) (C) (iii) and (iv) (D) (i) and (iv)

Last Answer : Answer: Option D

Normally, the tensile strength of concrete is about____________of its compressive strength (a) 10 to 15% (b) 15 to 20% (c) 20 to 25% (d) 25 to 30%

Description : Normally, the tensile strength of concrete is about____________of its compressive strength (a) 10 to 15% (b) 15 to 20% (c) 20 to 25% (d) 25 to 30%

Last Answer : (a) 10 to 15%

The tensile strength of concrete is about ________ of its compressive strength [ A ] 10% to 15% [ B ] 30% to 40% [ C ] 50% [ D ] 60% to 75%

Description : The tensile strength of concrete is about ________ of its compressive strength [ A ] 10% to 15% [ B ] 30% to 40% [ C ] 50% [ D ] 60% to 75%

Last Answer : [ A ] 10% to 15%

Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Description : Slump test of concrete is a measure of its [ A ] Consistency [ B ] Compressive strength [ C ] Tensile strength [ D ] Impact value

Last Answer : [ A ] Consistency

Pick up the correct proportions of chemical ingredients of cement (A) Lime : Silica : Alumina : Iron oxide : 63 : 22 : 6 : 3 (B) Silica : Lime : Alumina : Iron oxide : 63 : 22 : 6 : 3 (C) Alumina : Silica : Lime : Iron oxide : 63 : 22 : 6 : 3 (D) Iron oxide : Alumina : Silica : Lime : 63 : 22 : 6 : 3

Description : Pick up the correct proportions of chemical ingredients of cement (A) Lime : Silica : Alumina : Iron oxide : 63 : 22 : 6 : 3 (B) Silica : Lime : Alumina : Iron oxide : 63 : 22 : 6 : 3 (C) Alumina : Silica : ... oxide : 63 : 22 : 6 : 3 (D) Iron oxide : Alumina : Silica : Lime : 63 : 22 : 6 : 3

Last Answer : Answer: Option A

Pick up the correct statement regarding low heat cement from the following: (A) It possesses less compressive strength (B) Its initial setting time is about one hour (C) Its final setting time is about 10 hours (D) All the above

Description : Pick up the correct statement regarding low heat cement from the following: (A) It possesses less compressive strength (B) Its initial setting time is about one hour (C) Its final setting time is about 10 hours (D) All the above

Last Answer : Answer: Option D

According to IS specifications, the compressive strength of ordinary Portland cement after three days should not be less than (A) 7 MPa (B) 11.5 MPa (C) 16 MPa (D) 21 MPa

Description : According to IS specifications, the compressive strength of ordinary Portland cement after three days should not be less than (A) 7 MPa (B) 11.5 MPa (C) 16 MPa (D) 21 MPa

Last Answer : Answer: Option C

For performing the compressive strength test of cement, the size of cube mould should be (a) 7.06cm (b)75mm (c)80mm (d)All the above

Description : For performing the compressive strength test of cement, the size of cube mould should be (a) 7.06cm (b)75mm (c)80mm (d)All the above

Last Answer : (a) 7.06cm

The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2

Description : The compressive strength an ordinary Portland cement (1:3) after 7 days test should not be less than. (a) 11N/mm2 (b) 17.5 N/mm2 (c) 22 N/mm2 (d) 27.5N/m2

Last Answer : (b) 17.5 N/mm2

Which of the following cements is expected to have the highest compressive strength after 3 days (a) Ordinary Portland cement (b) Rapid hardening cement (c) High alumina cement (d) Sulphate resisting cement.

Description : Which of the following cements is expected to have the highest compressive strength after 3 days (a) Ordinary Portland cement (b) Rapid hardening cement (c) High alumina cement (d) Sulphate resisting cement.

Last Answer : (c) High alumina cement

Minimum compressive strength of cement required at the age of 3 days for ordinary Portland cement of grade 33 is [ A ] 1.15 N/mm2 [ B ] 11.5 N/mm2 [ C ] 2.10 N/mm2 [ D ] 21 N/mm2

Description : Minimum compressive strength of cement required at the age of 3 days for ordinary Portland cement of grade 33 is [ A ] 1.15 N/mm2 [ B ] 11.5 N/mm2 [ C ] 2.10 N/mm2 [ D ] 21 N/mm2

Last Answer : [ B ] 11.5 N/mm2

For determining the compressive strength test on cement is, the percentage amount of water to be added as (Pa = Percentage of water for required consistency) [ A ] 0.25 Pa + 2.5 [ B ] 0.25 Pa + 3.5 [ C ] 0.35 Pa + 2.5 [ D ] 0.35 Pa + 3.5

Description : For determining the compressive strength test on cement is, the percentage amount of water to be added as (Pa = Percentage of water for required consistency) [ A ] 0.25 Pa + 2.5 [ B ] 0.25 Pa + 3.5 [ C ] 0.35 Pa + 2.5 [ D ] 0.35 Pa + 3.5

Last Answer : [ B ] 0.25 Pa + 3.5

The expected out turn of 12 mm plastering with cement mortar is (A) 2.5 sq m (B) 4.0 sq m (C) 6.0 sq m (D) 8.0 sq m

Description : The expected out turn of 12 mm plastering with cement mortar is (A) 2.5 sq m (B) 4.0 sq m (C) 6.0 sq m (D) 8.0 sq m

Last Answer : (D) 8.0 sq m

The minimum thickness of walls built in cement mortar (1 : 6) for a single storey building, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Description : The minimum thickness of walls built in cement mortar (1 : 6) for a single storey building, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : Answer: Option C

Consider the following statements: Maximum slenderness ratio of load-bearing masonry walls for a dwelling having more than two storeys shall not exceed. 1. 12, if lime mortar is used 2. 18, if cement-lime mortar 1:2:9 is used 3. 24, if cement mortar 1:6 is used\ Which of these statements are correct? (a) 1 and 2 only b) 2 and 3 only c) 1 and 3 only d)1, 2 and 3

Description : Consider the following statements: Maximum slenderness ratio of load-bearing masonry walls for a dwelling having more than two storeys shall not exceed. 1. 12, if lime mortar is used 2. 18, if cement-lime mortar 1:2:9 is used 3. 24, ... ? (a) 1 and 2 only b) 2 and 3 only c) 1 and 3 only d)1, 2 and 3

Last Answer : b) 2 and 3 only

For quality control of Portland cement, the test essentially done is (A) Setting time (B) Tensile strength (C) Consistency (D) All the above

Description : For quality control of Portland cement, the test essentially done is (A) Setting time (B) Tensile strength (C) Consistency (D) All the above

Last Answer : D

Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by (A) Tensile strength test (B) Slump test (C) Compaction factor test (D) Flexural strength test

Last Answer : Answer: Option C

Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Description : Workability of concrete mix with low water cement ratio is determined by [ A ] Tensile strength test [ B ] Slump cone test [ C ] Compaction factor test [ D ] Flexural strength test

Last Answer : [ C ] Compaction factor test

While mixing sand, gravel, and cement for the foundation of a house, a worker noticed a small bird hopping along the top of the foundation wall. The bird misjudged a hop and fell down one of the holes between the blocks. The bird was down too far for anyone to reach it and the hole was too small for it to fly out of. Someone suggested using two sticks to reach down into the hole and pull the bird out, but this idea was rejected for fear it would injure the fragile bird. What would be the easiest way to get the bird out of the hole without injuring it? -Riddles

Description : While mixing sand, gravel, and cement for the foundation of a house, a worker noticed a small bird hopping along the top of the foundation wall. The bird misjudged a hop and fell down one of the holes ... . What would be the easiest way to get the bird out of the hole without injuring it? -Riddles

Last Answer : Since they had plenty of sand available, they could pour a little at a time into the hole. The bird would constantly keep shifting its position so that it stood on the rising sand.

Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these

Description : Steel rods are used in reinforced concrete to increase its __________ strength. (A) Shear (B) Tensile (C) Compressive (D) None of these

Last Answer : (B) Tensile

Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Description : Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Last Answer : (C) Machinability

Cast iron is (A) Used for making shock resisting parts (B) Manufactured in cupola and is brittle (C) Having compressive strength more than its tensile strength(D) All (A), (B) & (C)

Description : Cast iron is (A) Used for making shock resisting parts (B) Manufactured in cupola and is brittle (C) Having compressive strength more than its tensile strength (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (d) shear strength

he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (a) tensile strength

Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths

Description : Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths

Last Answer : (B) Sharp melting points

Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Description : Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Last Answer : (D) Thermal co-efficient of expansion

High copper amalgam lasts longer than low copper amalgam because of:** A. Increased compressive strength B. Increased corrosion resistance C. High creep D. Increased tensile strength E. Decreased setting expansion

Description : High copper amalgam lasts longer than low copper amalgam because of:**  A. Increased compressive strength  B. Increased corrosion resistance  C. High creep  D. Increased tensile strength  E. Decreased setting expansion 

Last Answer : A. Increased compressive strength 

.The main advantage of amalgam with high content of Cu is: A. Better marginal sealing B. Less corrosion C. Better tensile strength D. Higher and immediate compressive strength

Description : .The main advantage of amalgam with high content of Cu is: A. Better marginal sealing B. Less corrosion C. Better tensile strength D. Higher and immediate compressive strength

Last Answer : B. Less corrosion

Which of the following physical properties is TRUE of most dense ceramic materials? w) high tensile strength x) good ductility y) high compressive strength z) high electrical conductivity

Description : Which of the following physical properties is TRUE of most dense ceramic materials? w) high tensile strength x) good ductility y) high compressive strength z) high electrical conductivity

Last Answer : ANSWER: Y -- HIGH COMPRESSIVE STRENGTH

Pick up the incorrect statement from the following. While performing preliminary test on concrete (A) Proportions of the material and water should be the same as to be used at the work site (B) Cement should be mixed by hand in order to maintain uniformity (C) Concrete mix should be stored in air-tight containers (D) Concrete ingredients should be kept at a temperature of 37° ± 2°C

Description : Pick up the incorrect statement from the following. While performing preliminary test on concrete (A) Proportions of the material and water should be the same as to be used at the work site (B) ... in air-tight containers (D) Concrete ingredients should be kept at a temperature of 37° 2°C

Last Answer : Answer: Option D

For the manufacture of Portland cement, the proportions of raw materials used, are (A) Lime 63% ; silica 22% ; other ingredients 15% (B) Lime 22% ; silica 63% ; other ingredients 15% (C) Silica 40% ; lime 40% ; other ingredients 20% (D) Silica 70% ; lime 20% ; other ingredients 10%

Description : For the manufacture of Portland cement, the proportions of raw materials used, are (A) Lime 63% ; silica 22% ; other ingredients 15% (B) Lime 22% ; silica 63% ; other ingredients 15% (C) Silica 40% ; lime 40% ; other ingredients 20% (D) Silica 70% ; lime 20% ; other ingredients 10%

Last Answer : Answer: Option A