If the storey height is equal to length of RCC wall, the percentage increase in strength is (A) 0 (B) 10 (C) 20 (D) 30

If the storey height is equal to length of RCC wall, the percentage increase in strength is
(A) 0
(B) 10
(C) 20
(D) 30
by

1 Answer

Answer :

Option B
by

Related questions

If height of the first storey of a building is 3.2 m and riser is 13 cm, the number of treads required, is (A) 12 (B) 18 (C) 24 (D) 2

Description : If height of the first storey of a building is 3.2 m and riser is 13 cm, the number of treads required, is (A) 12 (B) 18 (C) 24 (D) 2

Last Answer : Answer: Option C

Minimum thickness of load bearing RCC wall should be (A) 50 mm (B) 100 mm (C) 150 mm (D) 200 mm

Description : Minimum thickness of load bearing RCC wall should be (A) 50 mm (B) 100 mm (C) 150 mm (D) 200 mm

Last Answer : (B) 100 mm

The minimum thickness of walls built in cement mortar (1 : 6) for a single storey building, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Description : The minimum thickness of walls built in cement mortar (1 : 6) for a single storey building, is (A) 10 cm (B) 15 cm (C) 20 cm (D) 25 cm

Last Answer : Answer: Option C

Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the sight on the down-slope, must be less than (A) 30 m (B) 25 m (C) 20 m (D) 15 m

Description : Keeping the instrument height as 1.5 m, length of staff 4 m, the slope of the ground as 1 in 10, the  sight on the down-slope, must be less than  (A) 30 m  (B) 25 m  (C) 20 m  (D) 15 m 

Last Answer : (B) 25 m 

For maximum strength and durability minimum percentage of cement, by weight is (A) 15 % (B) 20 % (C) 25 % (D) 30 %

Description : For maximum strength and durability minimum percentage of cement, by weight is (A) 15 % (B) 20 % (C) 25 % (D) 30 %

Last Answer : Answer: Option D

The minimum strain at failure in the tensile reinforcement (Fy = 400 MPa) of RCC beam as per limit state method is (a) 0.0020 (b) 0.0028 (c) 0.0037 (d) 0.0045

Description : The minimum strain at failure in the tensile reinforcement (Fy = 400 MPa) of RCC beam as per limit state method is (a) 0.0020 (b) 0.0028 (c) 0.0037 (d) 0.0045

Last Answer : (c) 0.0037

In the event of an earthquake and you're in a 20 storey building, Is your chance of survival higher at a the higher floors or lower floors.

Description : In the event of an earthquake and you're in a 20 storey building, Is your chance of survival higher at a the higher floors or lower floors.

Last Answer : answer:Naturally the lower you are the more likely you are going to be crushed. In the 1989 San Francisco quake, many houses pancaked into the street. Meaning the top floor crushed the lower floor ... comes toppling down, you'll have some sort or frame around you to prevent you from being crushed.

The percentage of reinforcement in case of slabs, when high strength deformed bars are used is not less than (A) 0.15 (B) 0.12 (C) 0.30 (D) 1.00

Description : The percentage of reinforcement in case of slabs, when high strength deformed bars are used is not less than (A) 0.15 (B) 0.12 (C) 0.30 (D) 1.00

Last Answer : Answer: Option B

Pick up the incorrect statement from the following: (A) The built up covered area at the floor level of any storey of a building is called plinth area (B) The usable covered area of the rooms of any storey of a building is called carpet area (C) The carpet area of a building along with area of its kitchen, pantry, store, lavatory, bath room and glazed veranda, is called floor area (D) None of thes

Description : Pick up the incorrect statement from the following: (A) The built up covered area at the floor level of any storey of a building is called plinth area (B) The usable covered area of the rooms of ... , pantry, store, lavatory, bath room and glazed veranda, is called floor area (D) None of thes

Last Answer : (D) None of thes

For each storey of a building, the depth of exploration should be (A) 1 metre (B) 2 metres (C) 3 metres (D) 4 metres

Description : For each storey of a building, the depth of exploration should be (A) 1 metre (B) 2 metres (C) 3 metres (D) 4 metres

Last Answer : Option C

Draw a neat sketch showing RCC components of lintel with 1:20 scale.

Description : Draw a neat sketch showing RCC components of lintel with 1:20 scale.

Last Answer : Draw a neat sketch showing RCC components of lintel with 1:20 scale.

Consider the following statements : 1. In a super-passage, the drain runs over the canal 2. In a siphon, the drain runs below the canal 3. In a siphon aqueduct, type- II, the canal banks are made of RCC walls Which of these statements are correct ? a) 1 only b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Description : Consider the following statements : 1. In a super-passage, the drain runs over the canal 2. In a siphon, the drain runs below the canal 3. In a siphon aqueduct, type- II, the canal banks are made of RCC walls Which of ... are correct ? a) 1 only b) 1 and 2 only c) 2 and 3 only d) 1 and 3 only

Last Answer : d) 1 and 3 only

In a group housing project, it is proposed to use pre-fabricated RCC beams and columns. The most useful construction equipment is (a) Derrick Crane (b) Chute (c) Weigh Batcher (d) Transit Mixer

Description : In a group housing project, it is proposed to use pre-fabricated RCC beams and columns. The most useful construction equipment is (a) Derrick Crane (b) Chute (c) Weigh Batcher (d) Transit Mixer

Last Answer : (a) Derrick Crane

The water pressure per metre length on a vertical masonry wall of dam is (where w = Specific weight of the liquid, and H = Height of the liquid) (A) wH/2(B) wH (C) wH2 /2 (D) wH2 /4

Description : The water pressure per metre length on a vertical masonry wall of dam is (where w = Specific weight of the liquid, and H = Height of the liquid) (A) wH/2 (B) wH (C) wH2 /2 (D) wH2 /4

Last Answer : Answer: Option C

A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. The total pressure on the wall per unit length is (where w = Specific weight of liquid, and H = Height of liquid) (A) wH (B) wH/2 (C) wH2 /2 (D) wH2 /3

Description : A vertical wall is subjected to a pressure due to one kind of liquid, on one of its sides. The total pressure on the wall per unit length is (where w = Specific weight of liquid, and H = Height of liquid) (A) wH (B) wH/2 (C) wH2 /2 (D) wH2 /3

Last Answer : Answer: Option C

7 persons enter an elevator on the ground floor of a 11 storey hotel. Any one of them can leave the elevator at any of the 10 floors. -Maths 9th

Description : 7 persons enter an elevator on the ground floor of a 11 storey hotel. Any one of them can leave the elevator at any of the 10 floors. -Maths 9th

Last Answer : answer:

Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10, the sight on the up slope must be less than (A) 25 cm (B) 20 m (C) 45 m (D) 10 m

Description : Keeping the instrument height as 1½ m, length of staff 4 m, the up gradient of the ground 1 in 10,  the sight on the up slope must be less than  (A) 25 cm  (B) 20 m  (C) 45 m  (D) 10 m

Last Answer : (C) 45 m 

A cuboid shaped wooden block has 6 cm length, 4 cm breadth and 1 cm height. 17. Two faces measuring 4 cm x 1 cm are coloured in black. 18. Two faces measuring 6 cm x 1 cm are coloured in red. 19. Two faces measuring 6 cm x 4 cm are coloured in green. 20. The block is divided into 6 equal cubes of side 1 cm (from 6 cm side), 4 equal cubes of side 1 cm(from 4 cm side). How many cubes will have green colour on two sides and rest of the four sides having no colour ? (a)12 (b)10 (c)8 (d)4

Description : A cuboid shaped wooden block has 6 cm length, 4 cm breadth and 1 cm height. 17. Two faces measuring 4 cm x 1 cm are coloured in black. 18. Two faces measuring 6 cm x 1 cm are coloured in red. 19. Two faces ... colour on two sides and rest of the four sides having no colour ? (a)12 (b)10 (c)8 (d)4

Last Answer : Answer key : (c)

.Minimum earth cushion required over RCC Box is a) 300 mm b) 600 mm c) 0* d) 1000 mm

Description : .Minimum earth cushion required over RCC Box is a) 300 mm b) 600 mm c) 0* d) 1000 mm

Last Answer : c) 0*

The standard height of a standard rain gauge, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 50 cm

Description : The standard height of a standard rain gauge, is (A) 10 cm (B) 20 cm (C) 30 cm (D) 50 cm

Last Answer : Answer: Option C

The top diameter, bottom diameter and the height of a slump mould are: (A) 10 cm, 20 cm, 30 cm (B) 10 cm, 30 cm, 20 cm (C) 20 cm, 10 cm, 30 cm (D) 20 cm, 30 cm, 10 cm

Description : The top diameter, bottom diameter and the height of a slump mould are: (A) 10 cm, 20 cm, 30 cm (B) 10 cm, 30 cm, 20 cm (C) 20 cm, 10 cm, 30 cm (D) 20 cm, 30 cm, 10 cm

Last Answer : (A) 10 cm, 20 cm, 30 cm

In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Description : In a cantilever retaining wall without a heel slab (A) Thickness of the stem is kept same throughout (B) Base slab is made 10 cm thicker than the stem (C) Width of the base slab is kept 0.7 time the total height of the wall (D) All the above

Last Answer : Answer: Option D

The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface

Description : The toe projection of foundation slabs is taken (A) As one third of the base (B) As one sixth of overall height of the wall (C) Equal to heel slab (D) Below ground surface

Last Answer : Answer: Option A

Expansion Joints in masonry walls are provided in wall lengths usater than (A) 10 m (B) 20 m (C) 30 m (D) 40 m

Description : Expansion Joints in masonry walls are provided in wall lengths usater than (A) 10 m (B) 20 m (C) 30 m (D) 40 m

Last Answer : Answer: Option D

Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the rate of (P/4) + 3.0 percentage of water where P is the percentage of water for standard consistency (C) A cube mould of 10 cm × 10 cm × 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Description : Pick up the incorrect statement from the following. For performing compressive strength test of cement (A) Cement and standard sand mortar are used in the ratio of 1 : 3 (B) Water is added at the ... cm 10 cm is used (D) The prepared moulds are kept in a atmosphere of 50% relative humidity

Last Answer : Answer: Option A

The percentage of alumina in a good brick earth lies between (A) 5 to 10 % (B) 20 to 30 % (C) 50 to 60 % (D) 70 to 80 %

Description : The percentage of alumina in a good brick earth lies between (A) 5 to 10 % (B) 20 to 30 % (C) 50 to 60 % (D) 70 to 80 %

Last Answer : Answer: Option B

Percentage of silica in a good brick earth lies between (A) 5 to 10 % (B) 20 to 30 % (C) 50 to 60 % (D) 70 to 80

Description : Percentage of silica in a good brick earth lies between (A) 5 to 10 % (B) 20 to 30 % (C) 50 to 60 % (D) 70 to 80

Last Answer : Answer: Option C

A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2 MN/mm2 and Eb = 0.1 MN/mm2 , the stresses developed are: (A) b = 10 N/mm2s = 20 N/mm2(B) b = 8 N/mm2s = 16 N/mm2(C) b = 6 N/mm2s = 12 N/mm2(D) b = 5 N/mm2s = 10 N/mm

Description : A compound bar consists of two bars of equal length. Steel bar cross-section is 3500 mm2 and that  of brass bar is 3000 mm2 . These are subjected to a compressive load 100,000 N. If Eb = 0.2  MN/mm2  and Eb = 0.1 ... 6 N/mm2 s  = 12 N/mm2 (D) b = 5 N/mm2 s  = 10 N/mm

Last Answer : (A) b = 10 N/mm2 s  = 20 N/mm

The dimensions of a 35 litre forma for measuring aggregates by volume, are: (A) length 30 cm, breadth 25 cm, height 30 cm (B) length 39 cm, breadth 25 cm, height 32 cm (C) length 27 cm, breadth 27 cm, height 48 cm (D) length 220 cm, breadth 25 cm, height 40 cm

Description : The dimensions of a 35 litre forma for measuring aggregates by volume, are: (A) length 30 cm, breadth 25 cm, height 30 cm (B) length 39 cm, breadth 25 cm, height 32 cm (C) length 27 cm, breadth 27 cm, height 48 cm (D) length 220 cm, breadth 25 cm, height 40 cm

Last Answer : Answer: Option C

A 5 m ladder of mass 25 kg is placed in a position where its inclination to a vertical wall is at 30?. A 100 kg man is to climb the ladder. If the coefficient of static friction is 0.25 the height along ladder at which the slipping will be induced would be a.2.4 m b.1.6 m c.0.8 m d.1.2 m e.0.5 m

Description : A 5 m ladder of mass 25 kg is placed in a position where its inclination to a vertical wall is at 30?. A 100 kg man is to climb the ladder. If the coefficient of static friction is 0.25 the height along ladder at which the slipping will be induced would be a.2.4 m b.1.6 m c.0.8 m d.1.2 m e.0.5 m

Last Answer : c. 0.8 m

Where will you land if you jump off a two storey building? -Riddles

Description : Where will you land if you jump off a two storey building? -Riddles

Last Answer : In the hospital.

A woman lived in a small one storey cabin. Everything was pink the floor was pink the couch was pink the house was pink. What color were the stairs? -Riddles

Description : A woman lived in a small one storey cabin. Everything was pink the floor was pink the couch was pink the house was pink. What color were the stairs? -Riddles

Last Answer : There were no stairs, its a one storey cabin.

Which country has 142 storey house ?

Last Answer : Nowhere. But there are two bigger buildings. 142 storey building is being constructed in Bangladesh. Kali Pradeep of Sylhet is constructing a 142-storey building in Dhaka. It is the third largest building in the world. It has been named as Iconic Tower. Details- http://magurabarta24.com/5692-2/

Is it important for you to have a balcony in a two-storey house?

Description : Who lives in a multi-storey house in whatever ... is it important to have a balcony where you can move out?

Last Answer : It's not important for us to move out. I think whoever lives in a two-story house or condominium is smoothly out of the garden, and if he wants to move out, he goes on a trip or anywhere. The ... to smoke, but of course you can sit out a bit. The latter is not so important in my opinion.     

The clarigesters are A. Circular septic tanks B. Rectangular septic tanks C. Circular Imhoff double tanks with bottom hoppers D. Circular Imhoff double storey tanks without bottom hoppers

Description : The clarigesters are A. Circular septic tanks B. Rectangular septic tanks C. Circular Imhoff double tanks with bottom hoppers D. Circular Imhoff double storey tanks without bottom hoppers

Last Answer : ANS: D

Price -Rite Carpets is located out -of- town, in a large, low -cost single storey building with no window displays and takes a minimilist approach to store ambiance and customer service. The Price -Rite store is an example of a: A)discount shed. B)warehouse club. C)speciality store. D)convenience store.

Description : Price -Rite Carpets is located out -of- town, in a large, low -cost single storey building with no window displays and takes a minimilist approach to store ambiance and customer service. The Price - ... an example of a: A)discount shed. B)warehouse club. C)speciality store. D)convenience store.

Last Answer : A)discount shed

Find the false statement: (A) The relationship construct known as the weak relationship type was defined by Dey, Storey & Barron (1999). (B) A weak relationship occurs when two relationship types are linked by either Event-Precedent sequence or Condition-Precedent sequence (C) Conceptual model is not accurate representation of "Universe of interest". (D) Ternary, Quaternary and Quintary relationships are shown through a series of application scenario's and vignette's

Description : Find the false statement: (A) The relationship construct known as the weak relationship type was defined by Dey, Storey & Barron (1999). (B) A weak relationship occurs when two ... Ternary, Quaternary and Quintary relationships are shown through a series of application scenario's and vignette's

Last Answer : (C) Conceptual model is not accurate representation of "Universe of interest".

What is the full form of 'RCC' ? -How To ?

Description : What is the full form of 'RCC' ? -How To ?

Last Answer : The full form of 'RCC' is Reinforced Cement Concrete

What is the full form of RCC ?

Last Answer : RCC - Reinforced Cement Concrete

How to connect a RCC tie beam with existing RCC foundation/ RCC column

Description : How to connect a RCC tie beam with existing RCC foundation/ RCC column

Last Answer : Need Answer

Liver CT - RCC

Description : Liver CT - RCC

Last Answer : A: Regarding the type of contrasts you were given, barium is an oral contrast. you might or might not have the oral contrast for the other studies as oral contrasts are not needed to evaluate the ... Renal cell cancer are many times not picked up on PET scan due their metabolic state not picking up

Large diameter reinforced cement concrete (RCC) pipes are generally joined by __________ joint. (A) Flanged iron (B) Collar (C) Flexible (D) Expansion

Description : Large diameter reinforced cement concrete (RCC) pipes are generally joined by __________ joint. (A) Flanged iron (B) Collar (C) Flexible (D) Expansion

Last Answer : Option B

Which cement should not be used for bridge slabs ro RCC frames a) OPC b) Portland Pozzolana cement * c) Portland furnace slag cement d) Rapid hardening cement

Description : Which cement should not be used for bridge slabs ro RCC frames a) OPC b) Portland Pozzolana cement * c) Portland furnace slag cement d) Rapid hardening cement

Last Answer : b) Portland Pozzolana cement *

Steel channel sleepers are provided in bridges with superstructure of a) PSC slab b) PSC girder c) Steel girder* d) RCC Box

Description : Steel channel sleepers are provided in bridges with superstructure of a) PSC slab b) PSC girder c) Steel girder* d) RCC Box

Last Answer : c) Steel girder*

Suggest the minimum grade of concrete for following exposure condition. i) RCC work ii) Water retaining structure iii) Sea water construction iv) Pre-stressed concrete

Description : Suggest the minimum grade of concrete for following exposure condition. i) RCC work ii) Water retaining structure iii) Sea water construction iv) Pre-stressed concrete

Last Answer : Minimum grade of concrete for following exposure condition: i) RCC work = M 20 ii) Water retaining structure = M 25 iii) Sea water construction = M 20 for PCC and M 30 for RCC iv) Pre-stressed concrete = M 30

When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (A) h = 0.5 dc

Two concave lenses of 60 cm focal length are cemented on either side of a convex lens of 15 cm focal length. The focal length of the combination is (A) 10 cm (B) 20 cm (C) 30 cm (D) 40 cm

Description : Two concave lenses of 60 cm focal length are cemented on either side of a convex lens of 15 cm  focal length. The focal length of the combination is  (A) 10 cm  (B) 20 cm  (C) 30 cm  (D) 40 cm 

Last Answer : (C) 30 cm 

Metric chains are generally available in (A) 10 m and 20 m length (B) 15 m and 20 m length (C) 20 m and 30 m length (D) 25 m and 100 m length

Description : Metric chains are generally available in (A) 10 m and 20 m length (B) 15 m and 20 m length (C) 20 m and 30 m length (D) 25 m and 100 m length

Last Answer : (C) 20 m and 30 m length

The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm

Description : The diameter of the Vicat plunger is 10 mm and its length varies from (A) 20 mm to 30 mm (B) 30 mm to 40 mm (C) 40 mm to 50 mm (D) 50 mm to 60 mm

Last Answer : Answer: Option C

Expansion joints in masonry walls are provided if length exceeds (A) 10 m (B) 20 m (C) 30 m (D) 40 m

Description : Expansion joints in masonry walls are provided if length exceeds (A) 10 m (B) 20 m (C) 30 m (D) 40 m

Last Answer : Answer: Option D