Description : If N is the algebraic difference of grades, S is the minimum sight distance in metres, the length (L) of a summit curve is (A) NS/4 (B) NS²/4 (C) N²S/4 (D) (NS)²/4
Last Answer : Answer: Option B
Description : If N is the algebraic difference of grades, S is the head light beam distance in metres, the length (L) of a valley curve, is (A) NS²/4 (B) NS²/6 (C) NS²/9.6 (D) NS²/4.8
Last Answer : Answer: Option A
Description : If N is deviation angle the length L of a parabolic vertical curve for overtaking sight distance S, is (A) NS²/9.6 if L > S (B) NS²/9.6 if L < S (C) 2S - 9.6/N if L < S (D) Both (A) and (C)
Last Answer : Answer: Option D
Description : If N is deviation angle, the length L, of a parabolic vertical curve for safe stopping distance S, is (A) NS²/4.4 if L > S (B) 2S - 4.4/N if L < S (C) 2S - 4.4/N if L > S (D) Both (a) and (b)
Description : The safe length L of a valley curve for night travel is (A) 2S - (1.50 + 0.035 S)/N if L < S (B) NS²/(1.50 + 0.035 S) if L > S (C) Neither (a) nor (b) (D) Both (a) and (b
Description : If L is the length of vehicles in metres, C is the clear distance between two consecutive vehicles (stopping sight distance), V is the speed of vehicles in km/hour, the maximum number N of vehicles/hour, is (A) N = 1000 V / (L + C ... ) / 1000 V (C) N = 1000 L / (C + V) (D) N = 1000 C / (L + V)
Description : The maximum distance of the apex of a vertical curve of length L from the point of intersection of two grades + g1%, and - g2% (g1 > g2), is (A) L(g - g (B) L(g - g (C) L(g g (D) L(g - g
Last Answer : Answer: Option C
Description : Design of horizontal and vertical alignments, super-elevation, sight distance and grades, is worst affected by (A) Width of the vehicle (B) Length of the vehicle (C) Height of the vehicle (D) Speed of the vehicle
Description : For night travel, the length of a valley curve should be such that the head light beam distance is the same as (A) Stopping sight distance (B) Overtaking sight distance (C) Sum of (a) and (b) (D) Difference of (a) and (b)
Description : If the length of a combined footing for two columns l metres apart is L and the projection on the left side of the exterior column is x, then the projection y on the right side of the exterior column, in order to have a uniformly distributed ... l - ) (C) y = L/2 - (l + ) (D) y = L/2 - (l - )
Description : Length of vehicles does not affect (A) Extra widening (B) Minimum radius of turning (C) Passing sight distance (D) Width of shoulders
Description : If h and h1 are the heights of a light house and the observer in a ship in metres above M S L then the horizontal distance from the ship to the light house in kilometres is (A) h + h1) (B) h - h1) (C) h × h1) (D) 3.86 h + h1)
Last Answer : (A) h + h1)
Description : If metres is the distance between extreme axles of a vehicle, its gross load should not exceed (A) 1525 (L + 4.3) - 14.7 L2 (B) 1526 (L + 5.3) - 14.7 L2 (C) 1525 (L + 6.3) - 14.7 L2 (D) 1525 (L + 7.3) - 14.7 L2
Description : If C is basic capacity per lane, V is velocity in km/hour, S is stopping distance plus length of the vehicles in metres, the formula C = 1000V/S is applicable to (A) District roads (B) Two lane roads (C) Two lane roads in one direction (D) None of these
Description : Pick up the correct statement from the following: (A) Long tangent sections exceeding 3 km in length should be avoided (B) Curve length should be at least 150 metres for a deflection angle of 5 ... decrease in the deflection angle, 30 metre length of curve to be increased (D) All the above
Description : If degree of a road curve is defined by assuming the standard length of an arc as 30 metres, the radius of 1° curve is equal (A) 1719 m (B) 1146 m (C) 1046 m (D) 1619 m
Description : If the velocity of moving vehicles on a road is 24 km/per hour, stopping distance is 19 metres and average length of vehicles is 6 metres, the basic capacity of lane, is (A) 500 vehicles per hour (B) 700 vehicles per hour (C) 1000 vehicles per hour (D) 1250 vehicles per hour
Description : L, M and N started a business in which L invested Rs.15000/- for 2year, M invested Rs 25000/- for 3 years, N invested Rs.35000/- for 4 years. At the end of the profit received by them is Rs.9800/-. What is N’s share?. A) 5600 B) 5000 C) 5500 D) 4500
Last Answer : Answer: A) L = Rs.15000/- per 2 years M= Rs.25000/- per 3 years N = Rs.35000/- per 4 years = 15000 2 : 25000 3 : 35000 4 =30000:75000:140000=30:75:140 =6:15:28 Total = 49 parts -----> Rs. ... ) = 1 part ------> Rs.200/- Then, N's share is = 28 parts = Rs.200 28 parts = Rs.5600
Description : The piston of a steam engine moves in S.H.M. The crank rotates at 180 r.p.m. and the stroke length is 2 metres. The linear velocity of the piston when it is at a distance of 1 metre from the centre is a.8.88 m/sec b.16.32 m/sec c.5.88 m/sec d.8.16 m/sec e.Zero
Last Answer : e. Zero
Description : An R.C.C. beam of 25 cm width and 50 cm effective depth has a clear span of 6 metres and carries a U.D.L. of 3000 kg/m inclusive of its self weight. If the lever arm constant for the section is 0.865, the maximum intensity ... , is (A) 8.3 kg/cm2 (B) 7.6 kg/cm2 (C) 21.5 kg/cm2 (D) 11.4 kg/cm2
Description : Two cars were involved in an accident in the center of town. The man who was driving a little green car, had overtaken a big black car. The driver had misjudged the distance between him and the on ... . However, the driver of the green car was not charged with manslaughter, why was this so? -Riddles
Last Answer : The black car was a hearse and was on its way to a funeral.
Description : The absolute minimum sight distance required for stopping a vehicle moving with a speed of 80 kmph, is (A) 120 m (B) 200 m (C) 640 m (D) None of these
Description : A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural ... .19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz d) 0.666 and 8.50 Hz
Last Answer : a) 0.471 and 1.19 Hz
Description : When an up gradient of a highway meets a downgrade, the vertical curve provided, is known as (A) Valley curve (B) Sag curve (C) Summit curve (D) All the above
Description : ferent grades are joined together by a (A) Compound curve (B) Transition curve (C) Reverse curve (D) Vertical curve
Last Answer : (D) Vertical curve
Description : For stairs spanning l metres longitudinally between supports at the bottom and top of a flight carrying a load w per unit horizontal area, the maximum bending moment per metre width, is (A) wl²/4 (B) wl²/8 (C) wl²/12 (D) wl²/16
Description : For two stage network the switching elements for M inlets with r blocks and N outlets with s blocks is given by (A) Ms + Nr (B) Mr + Ns (C) (M + N) (r + s) (D) (M + N)rs
Last Answer : (A) Ms + Nr
Description : Prove N = Ns (1 — S).
Last Answer : Prove N = Ns (1 — S).
Description : Degree of a road curve is defined as the angle in degrees subtended at the centre by an arc of (A) 10 metres (B) 20 metres (C) 25 metres (D) 30 metres
Description : A vehicle suspension system consists of a spring and a damper. The stiffness of the spring is 3.6 kN/m and the damping constant of the damper is 400 Ns/m. If the mass is 50 kg, then the damping factor (d ) and damped natural ... , are a) 0.471 and 1.19 Hz b) 0.471 and 7.48 Hz c) 0.666 and 1.35 Hz
Description : Five persons M, N, O, P and Q request a bank for safety lockers. There are only 6 lockers available which are numbered from 52 to 57. The conditions are as follows: I. M's locker number is 2 less than O's lockers ... could be a) 52 or 53 only b) 53 or 54 only c) 54 or 55 only d) 53 or 55 only
Last Answer : c) 54 or 55 only
Description : Five persons M, N, O, P and Q request a bank for safety lockers. There are only 6 lockers available which are numbered from 52 to 57. The conditions are as follows: I. M's locker number is 2 less ... , then which locker number is not allocated? a) locker 52 b) locker 53 c) locker 54 d)locker 56
Last Answer : a) locker 52
Description : If S, L and R are the arc length, long chord and radius of the sliding circle then the perpendicular distance of the line of the resultant cohesive force, is given by (A) a = S.R/L (B) a = L.S/R (C) a = L.R/S (D) None of these
Last Answer : (A) a = S.R/L
Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)
Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow
Description : If is the length of a sub-chord and is the radius of simple curve, the angle of deflection between its tangent and sub-chord, in minutes, is equal to (A) 573 S/R (B) 573 R/S (C) 1718.9 R/S (D) 1718.9 S/R
Last Answer : (D) 1718.9 S/R
Description : The difference of level between a point below the plane of sight and one above, is the sum of two staff readings and an error would be produced equal to (A) The distance between the zero of ... Thrice the distance between the zero of graduation and the foot of the staff (D) None of the above
Last Answer : (B) Twice the distance between the zero of graduation and the foot of the staff
Description : What is the minimum distance (in metres) required to hear an echo? (1) 10 (2) 13 (3) 17 (4) 21
Last Answer : (3) 17 Explanation: The human ear cannot distinguish echo from the original direct sound if the delay is less than 1/15 of a second. The velocity of sound in dry air is approximately 343 m/s at a temperature of 25⁰C.
Description : Floating gradients are generally provided (A) Along maximum gradients (B) Along minimum gradients (C) At summit curves (D) At valley curves
Description : If R is the radius of a main curve and L is the length of the transition curve, the shift of the curve, is (A) L/24 R (B) L2 /24 R (C) L3 /24 R (D) L4 /24 R
Description : If the rate of change of grade permitted along a vertical curve is r and total change of grade is g%, the length L of the curve to be provided, is (A) L = (r × 100/g) m (B) L = (g × 100/r) m (C) L = (r + g) × 100m (D) L = [100/(r + g)] m
Description : An upgrade g1% is followed by a downgrade g2%. The equation of the parabolic curve of length L to be introduced, is given by (A) y = g [(g - g L] x² (B) y = [(g g L] x² (C) y = [(g - g L] x² (D) y = [(g g L] x²
Description : If L is the length of a moving vehicle and R is the radius of curve, the extra mechanical width b to be provided on horizontal curves, (A) L/R (B) L/2R (C) L²/2R (D) L/3R
Description : If a fiber optic system has a rise time of 16 ns, the source rise time is 1.5 ns and the detector rise time is 2 ns, what is the cable rise time? A. 14 ns B. 6 ns C. 9 ns D. 12.5 ns
Last Answer : A. 14 ns
Description : Pick up the correct statement from the following: (A) If the slope of the curve of a mass diagram in the direction of increasing abscissa is downward, it indicates an embankment (B) The ... and the next forward maximum ordinate represents the whole volume of a cutting (D) All the above
Last Answer : (D) All the above
Description : The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channel capacity. Assuming that processing ... maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D
Last Answer : c. C
Description : Minimum horsepower of pump required for filling 50m3 water tank, 20 metres high from ground in 30 minutes by lifting water from a well 5 metres below the ground level is a.5.45 KW b.7.5 KW c.6.81 KW d.Tapered bearing e.66.8 KW
Last Answer : c. 6.81 KW
Description : An R.C.C beam of 25 cm width has a clear span of 5 metres and carries a U.D.L. of 2000 kg/m inclusive of its self weight. If the lever arm of the section is 45 cm., the beam is ( ... shear (B) Is safe with stirrups (C) Is safe with stirrups and inclined members (D) Needs revision of the section
Description : Two columns 50 cm 50 cm and 60 cm 60 cm carry 80 tonnes and 120 tonnes of loads respectively. The centre to centre distance between columns is 5.00 metres. The permissible bearing capacity of the soil is 20 t ... the foundation slab = 7.00 m (C) Area of footing slab = 11.00 m2 (D) All the above
Last Answer : Option D
Description : The reduced levels of points, 30 metres apart along the longitudinal section of a road portion between chainages 5 and 9 are shown in the given figure. If there is a uniform up-gradient of the road 120 in 1, the chainage ... 15) chains (B) (6 + 12) chains (C) (6 + 18) chains (D) None of these
Last Answer : (B) (6 + 12) chains
Description : The radius of curvature provided along a transition curve, is (A) Minimum at the beginning (B) Same throughout its length (C) Equal to the radius of circular curve (D) Varying from infinity to the radius of circular curve