Description : the loss due to friction in pipes is 4 m, the total losses in strainer and bends may be taken as (A) 0.10 m (B) 0.20 m (C) 0.5 m (D) 1.0 m
Last Answer : Answer: Option D
Description : The efficiency of power transmission through pipe is (where H = Total supply head, and hf = Head lost due to friction in the pipe) (A) (H - hf )/H (B) H/(H - hf ) (C) (H + hf )/H (D) H/(H + hf )
Last Answer : Answer: Option A
Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the ... the water horse power of the pump is (A) 400 (B) 450 (C) 500 (D) 600
Last Answer : (D) 600
Description : The most important and widely used tube well in India, is (A) Strainer well (B) Cavity well (C) Slotted well (D) Perforated pipe well
Last Answer : (A) Strainer well
Description : Pick up the incorrect statement from the following: (A) The flow in strainer type wells is radial (B) The flow in cavity type wells in spherical (C) In strainer type wells, area of flow ... pipe (D) In cavity type wells, area of flow depends upon the size of the cavity
Last Answer : (C) In strainer type wells, area of flow depends upon the length of the strainer pipe
Description : What is the value of Fanning friction factor f ' for smooth pipe at NRe = 10 6 approximately? (A) 0.003 (B) 0.01 (C) 0.1 (D) 0.3
Last Answer : (A) 0.003
Description : In India post-harvest losses of fruit and vegetable is… per cent of the total production. a) 15-20 b) 50-50 c) 40-45 d) 25-30
Last Answer : a) 15-20
Description : According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd
Description : The loss of head due to friction in a pipe of uniform diameter in which a viscous flow is taking place, is (where RN = Reynold number) (A) 1/RN (B) 4/RN (C) 16/RN (D) 64/RN
Last Answer : Answer: Option C
Description : Which of the following pipe bends will incur the largest head loss? (A) U-bend (B) 30° bend (C) 45° bend (D) 90° bend
Last Answer : (A) U-bend
Description : The power transmitted through the nozzle is maximum when the head lost due to friction in the pipe is __________ of the total supply head. (A) One-half (B) One-third (C) Two-third (D) None of these
Last Answer : Answer: Option B
Description : The power transmitted through the pipe is maximum when the head lost due to friction is equal to (A) One-fourth of the total supply head (B) One-third of the total supply head (C) One-half of the total supply head (D) Two-third of the total supply head
Description : The minimum design speed for hairpin bends in hill roads is taken as (A) 20 kmph (B) 30 kmph (C) 40 kmph (D) 50 kmph
Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number
Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads
Description : In parallel pipe problems, the (A) Head loss is the same through each pipe (B) Discharge is the same through all the pipes (C) Total head loss is equal to the sum of the head losses through each pipe (D) None of these
Last Answer : (A) Head loss is the same through each pipe
Description : A pressure conduit laid underground, may not be subjected to (A) Internal pressure of water (B) Pressure due to external load (C) Longitudinal temperature stress (D) Longitudinal stresses due to unbalanced pressure to bends
Last Answer : (C) Longitudinal temperature stress
Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the ... , is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm
Last Answer : (C) 20 mm
Description : Two pipe systems can be said to be equivalent, when the following quantities are same (A) Friction loss and flow (B) Length and diameter (C) Flow and length (D) Friction factor and diameter
Description : Major loss in sudden contraction in pipe flow is due to (A) Boundary friction (B) Flow contraction (C) Expansion of flow after sudden contraction (D) None of these
Last Answer : (B) Flow contraction
Description : Power transmitted through a pipe is maximum when the loss of head due to friction is : (A) one-half of the total head supplied (B) one-third of the total head supplied (C) one-fourth of the total head supplied (D) zero
Last Answer : Power transmitted through a pipe is maximum when the loss of head due to friction is : one-third of the total head supplied
Description : A 10 cm dia steam pipe, carrying steam at 180°C, is covered with an insulation (conductivity = 0.6 W/m.°C). It losses heat to the surroundings at 30°C. Assume a heat transfer co-efficient of 0 ... that of the un-insulated steam pipe (D) Less than the steam pipe with 5 cms insulation
Last Answer : (B) Less than that of the un-insulated steam pipe
Description : In case of a pipe exit fitted with a nozzle, the (A) Conversion of kinetic head to pressure head is facilitated (B) Conversion of pressure head to kinetic head is facilitated (C) Power transmitted through the nozzle ... in the pipe is equal to one third of the total supply head (D) Both (B) and (C)
Last Answer : (D) Both (B) and (C)
Description : The armature of a dc machine is laminated to reduce: (A) Eddy current loss (B) Hysteresis loss (C) copper losses (D) friction and windage losses
Last Answer : Ans: A Thinner the laminations, greater is the resistance offered to the induced e.m.f., smaller the current and hence lesser the I2R loss in the core.
Description : Which of the following factors does not contribute to the pressure drop in a pipeline? (A) Velocity of fluid (B) Size of pipe (C) Length of pipe and number of bends (D) None of these
Last Answer : (D) None of these
Description : In case of Venturimeter, friction losses are about __________ percent of maximum velocity head. (A) 2 (B) 8 (C) 12 (D) 20
Last Answer : (A) 2
Description : While designing hair pin bends on highways, the minimum (A) Designed speed is 20 km/hour (B) Gradient is 1 in 40 (C) Gradient is 1 in 200 (D) All the above
Description : When a number of hair pin bends are introduced, a minimum intervening distance in between is kept (A) 20 m (B) 40 m (C) 60 m (D) 100 m
Description : A crate weighing 40 kg rests on a cart moving with an acceleration W. The coefficient of friction between the cart and the crate is a.2.45 m/sec2 b.4.00 m/sec2 c.0.25 m/sec2 d.4.16 m/sec2 e.1.25 m/sec2
Last Answer : a. 2.45 m/sec2
Description : For 3.25 × 10-2 cumecs discharging from a well, a pump is installed to lift water against a total head of 30 m. The minimum required horse power, is (A) 10 H.P. (B) 15 H.P. (C) 18 H.P. (D) 20 H.P.
Last Answer : (D) 20 H.P.
Description : Total mechanical losses ( frictional losses , pumping loss in intake and exhaust and power accessories) will amount to a.10-20 % ihp b.2-10 % ihp c.20-30 % ihp d.30 -50 % ihp
Last Answer : a.10-20 % ihp
Description : In case of flow through parallel pipes, (A) The head loss for all the pipes is same (B) The total discharge is equal to the sum of discharges in the various pipes (C) The total head loss is the sum of head losses in the various pipes (D) Both (A) and (B)
Description : The term power budgeting refers to ∙ A. the cost of cable, connectors, equipment and installation ∙ B. the loss of power due to defective components ∙ C. the total power available minus the attenuation losses ∙ D. the comparative costs of fiber and copper installations
Last Answer : C. the total power available minus the attenuation losses
Description : A furnace is made of a refractory brick wall of thickness 0.5 metre and thermal conductivity 0.7 W/m.°K For the same temperature drop and heat loss, this refractory wall can be replaced by a layer of diatomaceous earth of ... and thickness __________ metre. (A) 0.01 (B) 0.1 (C) 0.25 (D) 0.5
Last Answer : (B) 0.1
Description : A Venturimeter cannot be used for the direct measurement of (A) Datum difference in the stretch of pipe-flow (B) Pressure difference in the flow through pipeline (C) Friction loss in pipe flow (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Which of the following losses of pre-stress occurs only in pre-tensioning and not in posttensioning? (A) Elastic shortening of concrete (B) Shrinkage of concrete (C) Creep of concrete (D) Loss due to friction
Description : The specific gravity of water is taken as (A) 0.001 (B) 0.01 (C) 0.1 (D) 1
Description : In a research on the effect of child-rearing practices on stress-proneness of children in competing school projects, the hypothesis formulated is that child rearing practices do influence stress-proneness'. At ... be rejected. (D) No decision can be taken in respect of the research hypothesis.
Last Answer : (B) The research hypothesis will be accepted.
Description : The strainer type tube well, is unsuitable for (A) Coarse gravels (B) Fine sandy strata (C) Clean gravels (D) None of these
Last Answer : (B) Fine sandy strata
Description : Abyssinian tube well is a special type of (A) Slotted type wells (B) Cavity type wells (C) Strainer type well (D) None of these
Last Answer : (C) Strainer type well
Description : A strainer type well sunk through three previous layers intervened by three impervious aquicludes, draws water from (A) Top most pervious layer (B) Central pervious layer (C) Lowest pervious layer (D) All the pervious layer
Last Answer : (D) All the pervious layers
Description : Shrouding' is essentially provided in (A) Strainer type wells (B) Cavity type wells (C) Slotted type well (D) All the above
Last Answer : (C) Slotted type well
Description : Shrouding is provided in (A) Cavity type tube wells (B) Slotted type tube wells (C) Strainer type tube wells (D) Perforated type tube wells
Description : The void ratio of a soil sample decreases from 1.50 to 1.25 when the pressure is increased from 25 tonnes/m2 to 50 tonnes/m2 , the coefficient of compressibility is (A) 0.01 (B) 0.02 (C) 0.05 (D) 0.001
Last Answer : (A) 0.01
Description : Which of the following statement(s) is/are true concerning protein/amino acid metabolism in man? a. The major source of amino acids is breakdown of circulating proteins b. The recommended daily ... balance refers to a decrease in nitrogen taken into the body versus the amount of nitrogen lost
Last Answer : Answer: b, d About 15% of the total body weight is made up of proteins, about half of which are intracellular and half extracellular. In man and other animals, dietary protein is the source of ... is exceeded by the amount of nitrogen lost in the urine, stool, skin, wounds, and fistula drainage
Description : A fluid (µ/ρ) = 0.01 cm2 /sec is moving at critical flow condition (NRe = 2100) through a pipe of dia 3 cms. Velocity of flow is __________ cm/sec. (A) 7 (B) 700 (C) 7000 (D) 630
Last Answer : (A) 7
Description : Pre-stress loss due to friction occurs (A) Only in post-tensioned beams (B) Only in pre-tensioned beams (C) In both post-tensioned and pre-tensioned beams (D) None of the above
Description : Which one of the following statements is not correct with respect to PSC beams? (a) Loss due to shrinkage is proportional to water-cement ratio used in concrete (b) Loss due to creep is ... to the modulus of elasticity of concrete (d) Loss due to friction occurs in post tensioned concrete members
Last Answer : (c) Loss due to elastic deformation is directly proportionally to the modulus of elasticity of concrete
Description : 14. When the pipes are in series, the total head loss is equal to the sum of the head loss in each pipe A) Yes B) No
Last Answer : A
Description : 45 The function of conservator in a transformer is A. To protect against internal fault B. To reduce copper as well as core losses C. To cool the transformer oil D. To take care of the expansion and contraction of transformer oil due to variation of temperature of surroundings
Last Answer : D. To take care of the expansion and contraction of transformer oil due to variation of temperature of surroundings
Description : If H is the height of the wave expected, then the height of the breakwater is generally taken as (A) 1.2 H to 1.25 H above the datum (B) 1.2 H to 1.25 H above the low water level (C) 1.2 H to 1.25 H above the high water level (D) 1.2 H to 1.25 H above the mean sea level
Last Answer : (C) 1.2 H to 1.25 H above the high water level