Use of water as a manometric liquid suffers from the disadvantage of its (A) Low vapour pressure (B) Corrosive nature (C) High vapour pressure (D) High boiling point

Use of water as a manometric liquid suffers from the disadvantage of its
(A) Low vapour pressure
(B) Corrosive nature
(C) High vapour pressure
(D) High boiling point
by

1 Answer

Answer :

(C) High vapour pressure
by

Related questions

Which of the following is an undesirable property of a manometricliquid? (A) Non-sticky & non-corrosive nature (B) High vapour pressure (C) Low viscosity & surface tension (D) Low co-efficient of thermal expansion

Description : Which of the following is an undesirable property of a manometricliquid? (A) Non-sticky & non-corrosive nature (B) High vapour pressure (C) Low viscosity & surface tension (D) Low co-efficient of thermal expansion

Last Answer : (B) High vapour pressure

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

Pick out the wrong statement: (A) The vacuum pressure is always the negative gauge pressure (B) The pressure of the liquid measured by a piezometer tube is the gauge pressure (C) Manometric liquid should have high surface tension (D) The point at which the resultant pressure on an immersed surface acts, is known as the centre of gravity

Description : Pick out the wrong statement: (A) The vacuum pressure is always the negative gauge pressure (B) The pressure of the liquid measured by a piezometer tube is the gauge pressure (C) Manometric ... point at which the resultant pressure on an immersed surface acts, is known as the centre of gravity

Last Answer : (D) The point at which the resultant pressure on an immersed surface acts, is known as the centre of gravity

In a gas-liquid shell and tube heat exchanger, the(A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure gases are corrosive in nature (C) Gases to be heated/cooled is normally routed through the shell side, because the corrosion caused by the cooling water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Description : Leidenfrost point is a term concerned with the (A) Condensation of the saturated vapor on a cold surface (B) Concentration of a corrosive solution by evaporation (C) Heat transfer between two highly viscous liquids (D) Boiling of a liquid on a hot surface

Last Answer : (D) Boiling of a liquid on a hot surface

Aluminium as a material of construction suffers from the disadvantage of (A) Very high cost (B) Rather low tensile strength (C) Very low strength to weight ratio (D) Scarce availability

Description : Aluminium as a material of construction suffers from the disadvantage of (A) Very high cost (B) Rather low tensile strength (C) Very low strength to weight ratio (D) Scarce availability

Last Answer : (B) Rather low tensile strength

Batch tray dryers suffers from the disadvantage of (A) High maintenance cost (B) Non-uniform & low production rate (C) High labour cost & low heat economy (D) All 'a', 'b' & 'c'

Description : Batch tray dryers suffers from the disadvantage of (A) High maintenance cost (B) Non-uniform & low production rate (C) High labour cost & low heat economy (D) All 'a', 'b' & 'c'

Last Answer : (C) High labour cost & low heat economy

The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Description : The direct shear test suffers from the following disadvantage: (A) Drain condition cannot be controlled (B) Pore water pressure cannot be measured (C) Shear stress on the failure plane is not uniform (D) The area under the shear and vertical loads does not remain constant throughout the test

Last Answer : Answer: Option C

Assam (India) coals suffers mainly from the disadvantage of high __________ content. (A) Ash (B) Volatile matter (C) Sulphur (4-6%)

Description : Assam (India) coals suffers mainly from the disadvantage of high __________ content. (A) Ash (B) Volatile matter (C) Sulphur (4-6%)

Last Answer : (C) Sulphur (4-6%)

. A batch reactor suffers from following disadvantage. (A) Poor product quality control (B) High labour and handling cost (C) High shutdown time requirement for emptying, cleaning and refilling (D) All (A), (B) and (C)

Description : . A batch reactor suffers from following disadvantage. (A) Poor product quality control (B) High labour and handling cost (C) High shutdown time requirement for emptying, cleaning and refilling (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The type of liquor circulation system to be ' employed in evaporators (viz. natural or forced circulation) is determined mainly by the __________ of the liquid. (A) Viscosity (B) Density (C) Thermal conductivity (D) Corrosive nature

Description : The type of liquor circulation system to be ' employed in evaporators (viz. natural or forced circulation) is determined mainly by the __________ of the liquid. (A) Viscosity (B) Density (C) Thermal conductivity (D) Corrosive nature

Last Answer : (A) Viscosity

The feed to fractionating column is changed from saturated vapour to saturated liquid. If the separation and reflux ratio remains unchanged, the number of ideal stages will (A) Increase (B) Decrease (C) Remain same (D) Depend on saturated boiling point; may increase or decrease

Description : The feed to fractionating column is changed from saturated vapour to saturated liquid. If the separation and reflux ratio remains unchanged, the number of ideal stages will (A) Increase (B) Decrease (C) Remain same (D) Depend on saturated boiling point; may increase or decrease

Last Answer : (A) Increase

In sub-cooled boiling, (A) Temperature of the heating surface is less than the boiling point of the liquid (B) Temperature of the heating surface is more than the boiling point of the liquid (C) Bubbles from heating surface are absorbed by the mass of the liquid (D) Very large vapour space is necessary

Description : In sub-cooled boiling, (A) Temperature of the heating surface is less than the boiling point of the liquid (B) Temperature of the heating surface is more than the boiling point of the liquid (C) ... from heating surface are absorbed by the mass of the liquid (D) Very large vapour space is necessary

Last Answer : (B) Temperature of the heating surface is more than the boiling point of the liquid

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Description : Liquid delivery by centrifugal pump starts, only when the head developed by it is equal to the __________ head. (A) Manometric (B) Total (C) Static (D) Friction

Last Answer : (A) Manometric

Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Description : Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Last Answer : (B) Requirement of heat transfer area is low

The head developed by a centrifugal pump is largely determined by the (A) Power of the pump(B) Nature of the liquid being pumped(C) Angle of the vanes and the speed of the tip of the impeller(D) Vapour pressure of the liquid

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

True boiling point apparatus is used for the (A) Determination of characterisation factor (B) Evaluation of oil stocks (C) Determination of true vapour pressure (D) None of these

Description : True boiling point apparatus is used for the (A) Determination of characterisation factor (B) Evaluation of oil stocks (C) Determination of true vapour pressure (D) None of these

Last Answer : (D) None of these

On addition of solute in the solvent, the __________ of the solution decreases. (A) Boiling point (B) Freezing point (C) Vapour pressure (D) Both (B) and (C)

Description : On addition of solute in the solvent, the __________ of the solution decreases. (A) Boiling point (B) Freezing point (C) Vapour pressure (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Last Answer : (A) Manometric

Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation temperature of the liquid (C) Heat transfer from the surface of the liquid is less than that in film boiling (D) The temperature is less than that of film boiling

Description : Pick out the wrong statement about nucleate boiling. (A) Bubble generation is by expansion of entrapped gas/vapour at small cavities in the surface (B) Surface temperature is greater than the saturation ... less than that in film boiling (D) The temperature is less than that of film boiling

Last Answer : (D) The temperature is less than that of film boiling

The burnout heat flux in the nucleate boiling regime is not a function of the (A) Liquid density (B) Vapour density (C) Temperature difference (D) Heat of evaporation

Description : The burnout heat flux in the nucleate boiling regime is not a function of the (A) Liquid density (B) Vapour density (C) Temperature difference (D) Heat of evaporation

Last Answer : (B) Vapour density

Flash point of a liquid petroleum fuel gives an idea about its (A) Volatility (B) Explosion hazards characteristics (C) Nature of boiling point diagram (D) All (A), (B) and (C)

Description : Flash point of a liquid petroleum fuel gives an idea about its (A) Volatility (B) Explosion hazards characteristics (C) Nature of boiling point diagram (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Urea is formed only (A) In liquid phase (B) In vapour phase (C) At very high temperature (D) At very low pressure (vacuum)

Description : Urea is formed only (A) In liquid phase (B) In vapour phase (C) At very high temperature (D) At very low pressure (vacuum)

Last Answer : (A) In liquid phase

An ideal liquid refrigerant should (A) Not have a sub-atmospheric vapour pressure at the temperature in the refrigerator coils (B) Not have unduly high vapour pressure at the condenser temperature (C) Both (A) and (B) (D) Have low specific heat

Description : An ideal liquid refrigerant should (A) Not have a sub-atmospheric vapour pressure at the temperature in the refrigerator coils (B) Not have unduly high vapour pressure at the condenser temperature (C) Both (A) and (B) (D) Have low specific heat

Last Answer : (C) Both (A) and (B)

Explain with reason through which side of shell and tube heat exchanges, the following liquids are directed. (i) viscous liquid (ii) high pressure liquid (iii) corrosive liquid

Description : Explain with reason through which side of shell and tube heat exchanges, the following liquids are directed. (i) viscous liquid (ii) high pressure liquid (iii) corrosive liquid

Last Answer : Viscous liquid : Viscous liquid is passed through shell side Reason: because of the presence of baffles in the shell induce turbulence and hence increases heat transfer rate. High pressure liquid: High ... To avoid expensive alloy shells (in order to save the cost of expensive material for shell).

Pick out the wrong statement. (A) Packed towers are preferred for vacuum operation, because the pressure drop through the packing is less and they (packings) also lessen the possibility of tower wall collapse (B) Packed towers are preferred over plate towers for handling corrosive and foamy liquids (C) Diameter of randomly packed tower is normally more than 1.2 metres (D) Due to uneven supply and improper distribution of liquid, problem of channelling, loading & flooding is generally encountered in packed towers

Description : Pick out the wrong statement. (A) Packed towers are preferred for vacuum operation, because the pressure drop through the packing is less and they (packings) also lessen the ... of liquid, problem of channelling, loading & flooding is generally encountered in packed towers

Last Answer : (C) Diameter of randomly packed tower is normally more than 1.2 metres

At boiling point of liquids, its : (1) Temperature increases (2) Atmospheric pressure increases (3) Timperature remains increases (4) Vapour pressure decreases

Description : At boiling point of liquids, its : (1) Temperature increases (2) Atmospheric pressure increases (3) Timperature remains increases (4) Vapour pressure decreases

Last Answer : (3) Timperature remains increases

At boiling point of liquids, its – (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases

Description : At boiling point of liquids, its – (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases

Last Answer : (3) Temperature remains constant Explanation: An interesting property of matter is that its temperature remains constant during a phase change, assuming its surrounding pressure is constant. A liquid changes into gaseous state at a constant temperature called its boiling point.

At boiling point of liquids, its (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases

Description : At boiling point of liquids, its (1) Temperature increases (2) Atmospheric pressure increases (3) Temperature remains constant (4) Vapour pressure decreases 

Last Answer : Temperature remains constant

In the pressure cooker, cooking is faster because the increase in vapour pressure - (1) increase the specific heat (2) decreases the specific heat (3) decreases the boiling point (4) increases the boiling point

Description : In the pressure cooker, cooking is faster because the increase in vapour pressure - (1) increase the specific heat (2) decreases the specific heat (3) decreases the boiling point (4) increases the boiling point

Last Answer : (4) increases the boiling point

. Platinum catalyst used in the earlier days of sulphuric acid manufacture by contact process suffers from the drawback like (A) High cost (B) Fragile nature (C) Easy poiso(D) All (A), (B) and (C)ning tendency

Description : . Platinum catalyst used in the earlier days of sulphuric acid manufacture by contact process suffers from the drawback like (A) High cost (B) Fragile nature (C) Easy poisoning tendency (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Clausius-Clapeyron Equation gives accurate result, when the (A) Vapour pressure is relatively low and the temperature does not vary over wide limits (B) Vapour obeys the ideal gas law and the latent heat of vaporisation is constant (C) Volume in the liquid state is negligible compared with that in the vapour state (D) All (A), (B) and (C)

Description : Clausius-Clapeyron Equation gives accurate result, when the (A) Vapour pressure is relatively low and the temperature does not vary over wide limits (B) Vapour obeys the ideal gas law and the latent heat of ... is negligible compared with that in the vapour state (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co-efficient and fi° is the fugacity of the pure component i. the Ki value (Yi = Ki xi) is therefore, in general a function of (A) Temperature only (B) Temperature and pressure only (C) Temperature, pressure and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Description : A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co- ... and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Last Answer : (C) Temperature, pressure and liquid composition xi only

Flash point of an oil gives an idea of the (A) Nature of boiling point diagram of the system (B) Amount of low boiling fraction present (C) Explosion hazards (D) All (A), (B) and (C)

Description : Flash point of an oil gives an idea of the (A) Nature of boiling point diagram of the system (B) Amount of low boiling fraction present (C) Explosion hazards (D) All (A), (B) and (C)

Last Answer : (A) Nature of boiling point diagram of the system

Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the(A) Quantity & temperature of waste gas(B) Dust concentration & nature of dust in waste gas(C) Corrosive nature of the waste gas(D) All (A), (B) and (C)

Description : Design of waste heat boiler for recovery of waste heat from furnace gases depends upon the (A) Quantity & temperature of waste gas (B) Dust concentration & nature of dust in waste gas (C) Corrosive nature of the waste gas (D) All (A), (B) and (C)

Last Answer : (B) Dust concentration & nature of dust in waste gas

Biuret formation in urea is kept at minimum (< 1 %), because it is (A) Corrosive in nature (B) Toxic and harmful to some crops (C) Helpful in decomposition of urea (D) Explosive in nature

Description : Biuret formation in urea is kept at minimum (< 1 %), because it is (A) Corrosive in nature (B) Toxic and harmful to some crops (C) Helpful in decomposition of urea (D) Explosive in nature

Last Answer : (B) Toxic and harmful to some crops

Higher vapour pressure of gasoline indicates(A) Low flash point(B) High breathing loss(C) Both (A) and (B)(D) Neither (A) nor (B

Description : Higher vapour pressure of gasoline indicates (A) Low flash point (B) High breathing loss (C) Both (A) and (B) (D) Neither (A) nor (B

Last Answer : (D) Neither (A) nor (B

At triple point (for one component system), vapour pressure of solid as compared to that of liquid will be (A) More (B) Less (C) Same (D) More or less; depending on the system

Description : At triple point (for one component system), vapour pressure of solid as compared to that of liquid will be (A) More (B) Less (C) Same (D) More or less; depending on the system

Last Answer : (C) Same

Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Description : Specific speed of a centrifugal pump depends upon the __________ head. (A) Suction (B) Delivery (C) Manometric (D) None of these

Last Answer : (D) None of these

Various efficiencies of a centrifugal pump are related as (where, ηm = mechanical efficiency ηv = volumetric efficiency. ηma = manometric efficiency ηo = overall efficiency) (A) ηma × ηm × ηv = ηo (B) ηm = ηv . ηma (C) ηma = ηm × ηv (D) ηv = ηm × ηma

Description : Various efficiencies of a centrifugal pump are related as (where, ηm = mechanical efficiency ηv = volumetric efficiency. ηma = manometric efficiency ηo = overall efficiency) (A) ηma × ηm × ηv = ηo (B) ηm = ηv . ηma (C) ηma = ηm × ηv (D) ηv = ηm × ηma

Last Answer : (B) ηm = ηv . ηma

In case of __________ boiling, the bubbles formed on a submerged hot surface get absorbed in the mass of the liquid. (A) Nucleate (B) Pool (C) Low pressure (D) None of these

Description : In case of __________ boiling, the bubbles formed on a submerged hot surface get absorbed in the mass of the liquid. (A) Nucleate (B) Pool (C) Low pressure (D) None of these

Last Answer : (B) Pool

In stripping section of continuous distillation column, the (A) Liquid is stripped of high boiler (B) Liquid is enriched with high boiler (C) Vapour is stripped of low boiler (D) None of these

Description : In stripping section of continuous distillation column, the (A) Liquid is stripped of high boiler (B) Liquid is enriched with high boiler (C) Vapour is stripped of low boiler (D) None of these

Last Answer : (B) Liquid is enriched with high boiler

In rectifying section of a continuous distillation column, the (A) Vapour is enriched with low boilers (B) Vapour is enriched with high boilers (C) Liquid is stripped of high boilers (D) None of these

Description : In rectifying section of a continuous distillation column, the (A) Vapour is enriched with low boilers (B) Vapour is enriched with high boilers (C) Liquid is stripped of high boilers (D) None of these

Last Answer : (B) Vapour is enriched with high boilers

Boiling point of water gets lowered at high altitudes (e.g., hills), because (A) Temperature is low (B) Atmospheric pressure is low (C) Atmospheric pressure is high (D) None of these

Description : Boiling point of water gets lowered at high altitudes (e.g., hills), because (A) Temperature is low (B) Atmospheric pressure is low (C) Atmospheric pressure is high (D) None of these

Last Answer : Option B

An ideal coolant for a nuclear reactor should (A) Be a good absorber of neutrons (B) Be capable of attaining high temperature, only when it is pressurised (C) Have high density, but low heat transfer co-efficient (D) Be free from radiation damage and non-corrosive

Description : An ideal coolant for a nuclear reactor should (A) Be a good absorber of neutrons (B) Be capable of attaining high temperature, only when it is pressurised (C) Have high density, but low heat transfer co-efficient (D) Be free from radiation damage and non-corrosive

Last Answer : (D) Be free from radiation damage and non-corrosive

Dielectric (A) Is an electrical insulating material (B) Of low resistivity is preferred (C) Should have high thermal conductivity (D) Need not defy the corrosive action of chemicals

Description : Dielectric (A) Is an electrical insulating material (B) Of low resistivity is preferred (C) Should have high thermal conductivity (D) Need not defy the corrosive action of chemicals

Last Answer : (A) Is an electrical insulating material

Mercury is often used in barometer because (A) It is the best liquid (B) The height of barometer will be less (C) Its vapour pressure is so low that it may be neglected (D) Both (B) and (C)

Description : Mercury is often used in barometer because (A) It is the best liquid (B) The height of barometer will be less (C) Its vapour pressure is so low that it may be neglected (D) Both (B) and (C)

Last Answer : Answer: Option D

Molten sodium (as a coolant in fast breeder reactor) (A) Can’t attain high temperature at normal pressure (B) Is not at all corrosive, even at a higher temperature (C) Is highly radioactive at elevated temperatures and can cause explosion, when it comes in contact with air or water (D) None of these

Description : Molten sodium (as a coolant in fast breeder reactor) (A) Can’t attain high temperature at normal pressure (B) Is not at all corrosive, even at a higher temperature (C) Is highly radioactive at elevated temperatures and can cause explosion, when it comes in contact with air or water (D) None of these

Last Answer : (C) Is highly radioactive at elevated temperatures and can cause explosion, when it comes in contact with air or water