According to Unwin's formula, the diameter of a rivet of plate of thickness is : (A) d = 6.05 t (B) d = 1.5 t + 4 (C) d = t(D) d = t + 1.5

According to Unwin's formula, the diameter of a rivet of plate of thickness is : 

(A) d = 6.05 t

(B) d = 1.5 t + 4 

(C) d = t

(D) d = t + 1.5 

by

1 Answer

Answer :

(A) d = 6.05 t

by

Related questions

The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times. (A) Two (B) Four (C) Six (D) Eight

Description : The expected efficiency of a single riveted lap joint is of the order of 50%. If the thickness of the plate is increased four times, then the rivet diameter will have to be increased __________ times. (A) Two (B) Four (C) Six (D) Eight

Last Answer : Option A

The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Description : The maximum longitudinal pitch in bolted joints, subjected to tensile forces, wherein t = thickness of the plate and D = diameter of bolt, is (a) 32 D (b) 16 D (c) 32 t (d) 16 t

Last Answer : (d) 16 t

Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm. (A) 10 (B) 20 (C) 30 (D) 40

Description : Diameter of the rivet to be provided on a 20 mm. thick boiler plate will be __________ mm. (A) 10 (B) 20 (C) 30 (D) 40

Last Answer : (D) 40

Failure of riveted joints is due to (A) Tearing of the plates between the rivet hole and the edge of the plate (B) Tearing of plates between rivets (C) Shearing of rivets (D) All the above

Description : Failure of riveted joints is due to  (A) Tearing of the plates between the rivet hole and the edge of the plate  (B) Tearing of plates between rivets  (C) Shearing of rivets  (D) All the above 

Last Answer : (D) All the above 

Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the tip diameter should be equal to t (where, t = plate thickness to be welded) (C) In spot welding, two pieces to be joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Description : Pick out the wrong statement. (A) Seam welding, projection welding & spot welding are the classification of electrical resistance welding (B) Electrode tip in spot welding is of copper and the ... joined are overlapped and placed between two electrodes (D) Mild steel sheet cannot be spot welded

Last Answer : (D) Mild steel sheet cannot be spot welded

The diameter of hole for 20 dia rivet shall be a) 23 mm b) 18 mm c) 21.5 mm* d) 22 mm

Description : The diameter of hole for 20 dia rivet shall be a) 23 mm b) 18 mm c) 21.5 mm* d) 22 mm

Last Answer : c) 21.5 mm*

If d is the diameter of the pipe, p is the total internal pressure, f is the permissible tensile stress and n is the effective of the joint, the thickness t of metal pipe, is (A) n (pd/2f) (B) (1/n) (pd/2f) (C) (1/n) (pd/3f) (D) (1/n) (pf/d

Description : If d is the diameter of the pipe, p is the total internal pressure, f is the permissible tensile stress  and n is the effective of the joint, the thickness t of metal pipe, is  (A) n (pd/2f)  (B) (1/n) (pd/2f)  (C) (1/n) (pd/3f)  (D) (1/n) (pf/d

Last Answer : (B) (1/n) (pd/2f) 

If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Description : If is the internal pressure in a thin cylinder of diameter and thickness , the developed hoop stress, is (A) pd/2t (B) pd/4t (C) pd/t (D) 2pd/t

Last Answer : (A) pd/2t

Hazen’s formula VS = 418 (GS – Gw)d [(3T + 70)/100] is used for the settlement velocity of the particles of diameter A. Less than 0.01 mm B. Less than 0.05 mm C. Less than 0.1 mm D. Greater than 0.1 mm

Description : Hazen’s formula VS = 418 (GS – Gw)d [(3T + 70)/100] is used for the settlement velocity of the particles of diameter A. Less than 0.01 mm B. Less than 0.05 mm C. Less than 0.1 mm D. Greater than 0.1 mm

Last Answer : ANS: D

The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Description : The thickness of a laminar boundary layer over a flat plate at two different sections P and Q are 0.8 cm and 2.4 cm respectively. If the section Q is 3.6 m downstream of P, the distance of section P from the leading edge of the plate is (a) 0.32 m (b) 0.22 m (c) 0.40 m (d) 0.53 m

Last Answer : Ans: (c) Correct Answer is: 0.45 m

The difference in the reservoir level and the lowest point of the water mains is 180 m. The expected pressure due to water hammer is 7.5 kg/cm2 in a pressure conduit of diameter 1 m. Assuming the efficiency of the riveted joints of the pipe as 0.6 and minimum cover 3 mm for corrosion, the thickness of the pipe materials, is (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The difference in the reservoir level and the lowest point of the water mains is 180 m. The  expected pressure due to water hammer is 7.5 kg/cm2  in a pressure conduit of diameter 1 m.  Assuming the efficiency of the ... , is  (A) 10 mm  (B) 15 mm  (C) 20 mm  (D) 25 mm 

Last Answer : (C) 20 mm

The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8

Description : The ratio of the diameter of reinforcing bars and the slab thickness is (A) 1/4 (B) 1/5 (C) 1/6 (D) 1/8

Last Answer : (D) 1/8

According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Description : According to Darcy's formula, the loss of head due to friction in the pipe is (where f = Darcy's coefficient, l = Length of pipe, v = Velocity of liquid in pipe, and d = Diameter of pipe) (A) flv²/2gd (B) flv²/gd (C) 3flv²/2gd (D) 4flv²/2gd

Last Answer : Answer: Option D

If the specific gravity of a soil particle of 0.05 cm diameter is 2.67, its terminal velocity while settling in distilled water of viscosity, 0.01 poise, is (A) 0.2200 cm/sec (B) 0.2225 cm/sec (C) 0.2250 cm/sec (D) 0.2275 cm/sec

Description : If the specific gravity of a soil particle of 0.05 cm diameter is 2.67, its terminal velocity while settling in distilled water of viscosity, 0.01 poise, is (A) 0.2200 cm/sec (B) 0.2225 cm/sec (C) 0.2250 cm/sec (D) 0.2275 cm/sec

Last Answer : (D) 0.2275 cm/sec

For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Description : For determining the ultimate bearing capacity of soil, the recommended size of a square bearing plate to be used in load plate test should be 30 to 75 cm square with a minimum thickness of (A) 5 mm (B) 10 mm (C) 15 mm (D) 25 mm

Last Answer : Answer: Option D

For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Description : For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Last Answer : (a) 1.5 mm less than the plate thickness

The weakest section of a diamond riveting, is the section which passes through (A) First row (B) Second row (C) Central row (D) One rivet hole of end row

Description : The weakest section of a diamond riveting, is the section which passes through  (A) First row  (B) Second row  (C) Central row  (D) One rivet hole of end row 

Last Answer : (A) First row

In case of an eccentric loading on a bracket subjected to moment M, the tangential force developed in any rivet, at right angles to its radius vector r is (A) Mr/ r² (B) r²/Mr(C) Mr²/ r² (D) Mr/ r²

Description : In case of an eccentric loading on a bracket subjected to moment M, the tangential force  developed in any rivet, at right angles to its radius vector r is  (A) Mr/ r²  (B) r²/Mr (C) Mr²/ r²  (D) Mr/ r² 

Last Answer : (A) Mr/ r² 

If the rivets in adjacent rows are staggered and outermost row has only one rivet, the arrangement of the rivets, is called (A) Chain riveting (B) Zig-zag riveting (C) Diamond riveting (D) None of these

Description : If the rivets in adjacent rows are staggered and outermost row has only one rivet, the arrangement of the rivets, is called (A) Chain riveting (B) Zig-zag riveting (C) Diamond riveting (D) None of these

Last Answer : (C) Diamond riveting

The thickness of web for unstiffened plate girder with clear distance‘d’ between the flanges shall be not less than

Description : The thickness of web for unstiffened plate girder with clear distance‘d’ between the flanges shall be not less than

Last Answer : d/85

From a circular plate of diameter 6 cm is cut out a circle whose diameter is a radius of the plate. Find the e.g. of the remainder from the center of circular plate (A) 0.5 cm (B) 1.0 cm (C) 1.5 cm (D) 2.5 cm

Description : From a circular plate of diameter 6 cm is cut out a circle whose diameter is a radius of the plate. Find the e.g. of the remainder from the center of circular plate (A) 0.5 cm (B) 1.0 cm (C) 1.5 cm (D) 2.5 cm

Last Answer : (A) 0.5 cm

If the cohesive force (c), is 1.5 t/m2 , the density ) of the soil is 2.0 t/m3 , factor of safety (F) is 1.5 and stability factor (Sn) is 0.05, the safe height of a slope, is (A) 5 metres (B) 8 metres (C) 10 metres (D) 12 metres

Description : If the cohesive force (c), is 1.5 t/m2 , the density ) of the soil is 2.0 t/m3 , factor of safety (F) is 1.5 and stability factor (Sn) is 0.05, the safe height of a slope, is (A) 5 metres (B) 8 metres (C) 10 metres (D) 12 metres

Last Answer : (C) 10 metres

For a clay slope of height of 10 m, the stability number is 0.05, = 2.0 t/m3 , C = 2.5 t/m2 , the critical height of the slope of the soil, is (A) 4.0 m (B) 12.5 m (C) 25.0 m (D) 15.0 m

Description : For a clay slope of height of 10 m, the stability number is 0.05, = 2.0 t/m3 , C = 2.5 t/m2 , the critical height of the slope of the soil, is (A) 4.0 m (B) 12.5 m (C) 25.0 m (D) 15.0 m

Last Answer : (C) 25.0 m

A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing stress of 124 N/mm2. G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns

Last Answer : a. 10 turns

A cylinder is said to be thin if the ratio of its thickness and diameter, is less than (A) 1/25 (B) 1/20 (C) 1/15 (D) 1/10

Description : A cylinder is said to be thin if the ratio of its thickness and diameter, is less than (A) 1/25 (B) 1/20 (C) 1/15 (D) 1/10

Last Answer : (D) 1/10

The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : The minimum thickness of the cover at the end of a reinforcing bar should not be less than twice the diameter of the bar subject to a minimum of (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Description : The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Last Answer : [ C ] One-eighth

The basic formula for determination of pavement thickness was first suggested by (A) Spangler (B) Picket (C) Kelly (D) Goldbeck

Description : The basic formula for determination of pavement thickness was first suggested by (A) Spangler (B) Picket (C) Kelly (D) Goldbeck

Last Answer : Answer: Option D

According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 5 cm (B) 10 cm (C) 15 cm (D) 20 cm

Last Answer : Answer: Option C

According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 20 cm (B) 30 cm (C) 40 cm (D) 75 cm

Description : According to I.S.: 456, 1978 the thickness of reinforced concrete footing on piles at its edges, is kept less than (A) 20 cm (B) 30 cm (C) 40 cm (D) 75 cm

Last Answer : Answer: Option B

A proton moves at a speed `v = 2xx10^(6) m//s` in a region of constant magnetic field of magnitude B = 0.05 T. The direction of the proton when it ent

Description : A proton moves at a speed `v = 2xx10^(6) m//s` in a region of constant magnetic field of magnitude B = 0.05 T. The direction of the proton when it ent

Last Answer : A proton moves at a speed `v = 2xx10^(6) m//s` in a region of constant magnetic field of magnitude B = 0.05 T. ... `0.209 m` C. `2.82 m` D. `2.41 m`

In any case, the minimum diameter of the link in a column, according to IS:456-2000 is [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Description : In any case, the minimum diameter of the link in a column, according to IS:456-2000 is [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Last Answer : [ B ] 6 mm

The diameter of the stirrups according to IS : 456-2000 should not be less than [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Description : The diameter of the stirrups according to IS : 456-2000 should not be less than [ A ] 5 mm [ B ] 6 mm [ C ] 8 mm [ D ] 10 mm

Last Answer : [ B ] 6 mm

The graded-index multimode optical fiber has a core diameter of _____ nm. ∙ a. 0.5 ∙ b. 0.05 ∙ c. 0.0005 ∙ d. 5

Description : The graded-index multimode optical fiber has a core diameter of _____ nm. ∙ a. 0.5 ∙ b. 0.05 ∙ c. 0.0005 ∙ d. 5

Last Answer : ∙ a. 0.5

Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2

Description : Find the shear stress in a flange at the junction of hub in rigid flanged coupling if torsional moment is 2980N-m and diameter of hub being 125mm. Also the thickness of flange is 25mm. a) 6.77N/mm2 b) 10.24N/mm2 c) 4.84N/mm2 d) 4.22N/mm2

Last Answer : c) 4.84N/mm2

The length of the countersunk head rivet shank is, when L = length of the rivet, G = length of grip in mm; D = Dia of rivet in mm a) L =G +0.5 D + 1mm for every 4 mm of grip or part thereof * b) b) L =G +0.5 D + 1mm c) L =G +0.5 D d) None of the above

Description : The length of the countersunk head rivet shank is, when L = length of the rivet, G = length of grip in mm; D = Dia of rivet in mm a) L =G +0.5 D + 1mm for every 4 mm of grip or part thereof * b) b) L =G +0.5 D + 1mm c) L =G +0.5 D d) None of the above

Last Answer : a) L =G +0.5 D + 1mm for every 4 mm of grip or part thereof *

he length of the snap head rivet shank is, when L = length of the rivet, G = length of grip in mm; D = Dia of rivet in mm a) L =G +1.5 D + 1mm for every 4 mm of grip or part thereof * b) b) L =G +0.5 D + 1mm c) L =G +0.5 D d) None of the above

Description : he length of the snap head rivet shank is, when L = length of the rivet, G = length of grip in mm; D = Dia of rivet in mm a) L =G +1.5 D + 1mm for every 4 mm of grip or part thereof * b) b) L =G +0.5 D + 1mm c) L =G +0.5 D d) None of the above

Last Answer : a) L =G +1.5 D + 1mm for every 4 mm of grip or part thereof *

A practical formula for determining the thickness of insulation between low voltage and high voltage windings is (a) 1 + 0.2 kVmm (6) 2 + 0.5 kVmm (c) 4 + 0.7 kV mm (d) 5 + 0.9 kV mm

Description : A practical formula for determining the thickness of insulation between low voltage and high voltage windings is (a) 1 + 0.2 kVmm (6) 2 + 0.5 kVmm (c) 4 + 0.7 kV mm (d) 5 + 0.9 kV mm

Last Answer : (d) 5 + 0.9 kV mm

If b is the width of a plate joined by diamond riveting of diameter d, the efficiency of the joint is given by (A) (b + d)/b (B) (b - d)/b (C) (d - b)/d (D) (b - d)/d

Description : If b is the width of a plate joined by diamond riveting of diameter d, the efficiency of the joint is  given by  (A) (b + d)/b (B) (b - d)/b (C) (d - b)/d (D) (b - d)/d

Last Answer : (B) (b - d)/b

Flow of water in a pipe about 3 metres in diameter can be measured by (A) Orifice plate (B) Venturimeter (C) Rotameter (D) Pitot tube

Description : Flow of water in a pipe about 3 metres in diameter can be measured by (A) Orifice plate (B) Venturimeter (C) Rotameter (D) Pitot tube

Last Answer : Answer: Option D

The width of the flange of a T-beam, which may be considered to act effectively with the rib depends upon (A) Breadth of the rib (B) Overall thickness of the rib (C) Centre to centre distance between T-beams (D) All the above

Description : The width of the flange of a T-beam, which may be considered to act effectively with the rib depends upon (A) Breadth of the rib (B) Overall thickness of the rib (C) Centre to centre distance between T-beams (D) All the above

Last Answer : Answer: Option D

The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above

Description : The width of the flange of a T-beam should be less than (A) One-third of the effective span of the T-beam (B) Distance between the centres of T-beam (C) Breadth of the rib plus twelve times the thickness of the slab (D) Least of the above

Last Answer : Answer: Option D

the oil, N = Speed of the shaft, R = Radius of the shaft, and t = Thickness of the oil film) (A) 60t (B) 60t (C) 60t (D) 60t

Description : the oil, N = Speed of the shaft, R = Radius of the shaft, and t = Thickness of the oil film) (A) 60t (B) 60t (C) 60t (D) 60t

Last Answer : Answer: Option D

A reinforced concrete cantilever porch has thickness t. The main reinforcing steel will be placed (a) At mid-thickness (b) At t/3 from the top (c) Close to the bottom surface (d) Close to the top surface

Description : A reinforced concrete cantilever porch has thickness t. The main reinforcing steel will be placed (a) At mid-thickness (b) At t/3 from the top (c) Close to the bottom surface (d) Close to the top surface

Last Answer : (d) Close to the top surface

The allowable shear stress in the web of mild steel beams decreases with (a) Decrease in h/t ratio (b) Increase in h/t ratio (c ) Decrease in thickness (d) Increase in height Where h is the height and t is the thickness

Description : The allowable shear stress in the web of mild steel beams decreases with (a) Decrease in h/t ratio (b) Increase in h/t ratio (c ) Decrease in thickness (d) Increase in height Where h is the height and t is the thickness

Last Answer : (b) Increase in h/t ratio

In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Description : In a T-beam, the vertical distance between the bottom of the flange and the centre of the tensile reinforcement is (a) Breadth of flange (b) Thickness of flange (c) Breadth of slab (d) Depth of rib

Last Answer : (d) Depth of rib

The thickness of flange in a T-beam is taken equal to the total thickness of the slab, including cover. (a) True (b) False (c) Not known (d) None of these

Description : The thickness of flange in a T-beam is taken equal to the total thickness of the slab, including cover. (a) True (b) False (c) Not known (d) None of these

Last Answer : (a) True

In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.

Description : In a T-beam , the breadth of the rib is equal to the (a) Total thickness of the slab, including cover (b) Width of the portion of the beam in the compression zone (c) Width of the portion of the beam in the compression zone (d) All the above.

Last Answer : (c) Width of the portion of the beam in the compression zone

The portion of the slab which acts monolithically with the beam and which resists the compressive stresses, is called _________of flange of the T-beam (a) Length (b) Breadth (c) Thickness (d) Depth

Description : The portion of the slab which acts monolithically with the beam and which resists the compressive stresses, is called _________of flange of the T-beam (a) Length (b) Breadth (c) Thickness (d) Depth

Last Answer : (b) Breadth