Which of the following is an undesirable property of a manometricliquid? (A) Non-sticky & non-corrosive nature (B) High vapour pressure (C) Low viscosity & surface tension (D) Low co-efficient of thermal expansion

Which of the following is an undesirable property of a manometricliquid?
(A) Non-sticky & non-corrosive nature
(B) High vapour pressure
(C) Low viscosity & surface tension
(D) Low co-efficient of thermal expansion
by

1 Answer

Answer :

(B) High vapour pressure
by

Related questions

Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Description : Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Last Answer : (B) Requirement of heat transfer area is low

Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Description : Diffusion co-efficient generally depends upon the temperature, pressure & the nature of the components of the system. Its dimension is not the same as that of the (A) Mass transfer co-efficient (B) Thermal diffusivity (C) Kinematic viscosity (D) Volumetric diffusivity

Last Answer : (A) Mass transfer co-efficient

ick out the undesirable property for a good refrigerant. (A) High thermal conductivity (B) Low freezing point (C) Large latent heat of vaporisation (D) High viscosity

Description : ick out the undesirable property for a good refrigerant. (A) High thermal conductivity (B) Low freezing point (C) Large latent heat of vaporisation (D) High viscosity

Last Answer : (D) High viscosity

Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat exchanger, when the (A) Higher condensing film co-efficient is desired (B) Condensate is corrosive in nature (C) Lower pressure drop through the exchanger is desired (D) Temperature of the incoming vapor is very high Answer: Option B

Description : Condensing film co-efficient for steam on horizontal tubes ranges from 5000 to 15000 Kcal/hr.m2 .°C. Condensation of vapor is carried out inside the tube in a shell and tube heat ... drop through the exchanger is desired (D) Temperature of the incoming vapor is very high

Last Answer : (B) Supersaturated

Use of water as a manometric liquid suffers from the disadvantage of its (A) Low vapour pressure (B) Corrosive nature (C) High vapour pressure (D) High boiling point

Description : Use of water as a manometric liquid suffers from the disadvantage of its (A) Low vapour pressure (B) Corrosive nature (C) High vapour pressure (D) High boiling point

Last Answer : (C) High vapour pressure

Which one of the following statements is correct ? a) For water at 100o Celsius at sea level, the vapour pressure is equal to atmospheric pressure b) Surface energy (or tension) is caused by the force of adhesion between liquid molecules c) Viscosity of a fluid is the property exhibited by it both in static and in dynamic conditions d) Air is 50,000 times more compressible than water

Description : Which one of the following statements is correct ? a) For water at 100o Celsius at sea level, the vapour pressure is equal to atmospheric pressure b) Surface energy (or tension) is caused by ... it both in static and in dynamic conditions d) Air is 50,000 times more compressible than water

Last Answer : c) Viscosity of a fluid is the property exhibited by it both in static and in dynamic conditions

Superior quality laboratory apparatus is made of the __________ glass having low thermal co-efficient of expansion & high chemical resistance. (A) Flint (B) Soda (C) Pyrex (D) Potash

Description : Superior quality laboratory apparatus is made of the __________ glass having low thermal co-efficient of expansion & high chemical resistance. (A) Flint (B) Soda (C) Pyrex (D) Potash

Last Answer : (C) Pyrex

The type of liquor circulation system to be ' employed in evaporators (viz. natural or forced circulation) is determined mainly by the __________ of the liquid. (A) Viscosity (B) Density (C) Thermal conductivity (D) Corrosive nature

Description : The type of liquor circulation system to be ' employed in evaporators (viz. natural or forced circulation) is determined mainly by the __________ of the liquid. (A) Viscosity (B) Density (C) Thermal conductivity (D) Corrosive nature

Last Answer : (A) Viscosity

An ideal coolant for a nuclear reactor should (A) Be a good absorber of neutrons (B) Be capable of attaining high temperature, only when it is pressurised (C) Have high density, but low heat transfer co-efficient (D) Be free from radiation damage and non-corrosive

Description : An ideal coolant for a nuclear reactor should (A) Be a good absorber of neutrons (B) Be capable of attaining high temperature, only when it is pressurised (C) Have high density, but low heat transfer co-efficient (D) Be free from radiation damage and non-corrosive

Last Answer : (D) Be free from radiation damage and non-corrosive

Which of the following is an undesirable property for an absorbingsolvent? (A) Low vapour pressure (B) Low velocity (C) Low freezing point (D) None of these

Description : Which of the following is an undesirable property for an absorbingsolvent? (A) Low vapour pressure (B) Low velocity (C) Low freezing point (D) None of these

Last Answer : (D) None of these

Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore? (A) High fusibility & fluidity (B) High thermal conductivity (C) Low density (D) High chemical activity

Description : Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore? (A) High fusibility & fluidity (B) High thermal conductivity (C) Low density (D) High chemical activity

Last Answer : B) High thermal conductivity

Brass tubes are used in the manufacture of tubes of evaporators used in sugar and salt industries, mainly because of its (A) High co-efficient of thermal expansion (B) Low thermal conductivity (C) High corrosion resistance (D) All (A), (B) and (C)

Description : Brass tubes are used in the manufacture of tubes of evaporators used in sugar and salt industries, mainly because of its (A) High co-efficient of thermal expansion (B) Low thermal conductivity (C) High corrosion resistance (D) All (A), (B) and (C)

Last Answer : (C) High corrosion resistance

Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths

Description : Pick out the wrong statement pertaining to the properties of glasses. Glasses generally have (A) High electrical insulation properties (B) Sharp melting points (C) Low co-efficient of thermal expansion (D) Compressive strength much greater than their tensile strengths

Last Answer : (B) Sharp melting points

Presence of a non-condensing gas in a condensing vapour (A) Increases the rate of condensation (B) Decreases thermal resistance (C) Is desirable to increase the film co-efficient (D) None of these

Description : Presence of a non-condensing gas in a condensing vapour (A) Increases the rate of condensation (B) Decreases thermal resistance (C) Is desirable to increase the film co-efficient (D) None of these

Last Answer : (D) None of these

(1/V) (∂V/∂T)Pis the mathematical expression (A) Joule-Thomson co-efficient (B) Specific heat at constant pressure (Cp) (C) co-efficient of thermal expansion (D) Specific heat at constant volume (CV)

Description : (1/V) (∂V/∂T)Pis the mathematical expression (A) Joule-Thomson co-efficient (B) Specific heat at constant pressure (Cp) (C) co-efficient of thermal expansion (D) Specific heat at constant volume (CV)

Last Answer : (C) co-efficient of thermal expansion

In a gas-liquid shell and tube heat exchanger, the(A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure gases are corrosive in nature (C) Gases to be heated/cooled is normally routed through the shell side, because the corrosion caused by the cooling water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

The film co-efficient between condensing vapour and metal wall increases with (A) Increasing temperature of the vapour (B) Decreasing temperature of the vapour (C) Increasing viscosity of the film of condensate (D) Increasing temperature drop

Description : The film co-efficient between condensing vapour and metal wall increases with (A) Increasing temperature of the vapour (B) Decreasing temperature of the vapour (C) Increasing viscosity of the film of condensate (D) Increasing temperature drop

Last Answer : (A) Increasing temperature of the vapour

Out of the following refrigeration cycles, which one has the minimum COP (Co-efficient of performance)? (A) Air cycle (B) Carnot cycle (C) Ordinary vapour compression cycle (D) Vapour compression with a reversible expansion engine

Description : Out of the following refrigeration cycles, which one has the minimum COP (Co-efficient of performance)? (A) Air cycle (B) Carnot cycle (C) Ordinary vapour compression cycle (D) Vapour compression with a reversible expansion engine

Last Answer : A) Air cycle

Heat transfer by natural convection is enhanced in system with (A) High viscosity (B) High co-efficient of thermal expansio

Description : Heat transfer by natural convection is enhanced in system with (A) High viscosity (B) High co-efficient of thermal expansio

Last Answer : (B) High co-efficient of thermal expansion

__________ glass has the lowest co-efficient of thermal expansion and hence is more heat resistant. (A) Pyrex (B) Soda lime (C) Lead (D) High silica

Description : __________ glass has the lowest co-efficient of thermal expansion and hence is more heat resistant. (A) Pyrex (B) Soda lime (C) Lead (D) High silica

Last Answer : (A) Pyrex

Which of the following is an undesirable characteristic for the solvent used in gas absorption? (A) Low vapor pressure (B) Low viscosity (C) High gas solubility (D) None of these

Description : Which of the following is an undesirable characteristic for the solvent used in gas absorption? (A) Low vapor pressure (B) Low viscosity (C) High gas solubility (D) None of these

Last Answer : (D) None of these

The fluid property which matters for falling rain drops to acquire spherical shape is its (A) Pressure (B) Height of descend (C) Viscosity (D) Surface tension

Description : The fluid property which matters for falling rain drops to acquire spherical shape is its (A) Pressure (B) Height of descend (C) Viscosity (D) Surface tension

Last Answer : (D) Surface tension

High __________ is an undesirable property for a good refrigerant. (A) Specific heat (B) Latent heat of vaporisation (C) Viscosity (D) Specific vapor volume

Description : High __________ is an undesirable property for a good refrigerant. (A) Specific heat (B) Latent heat of vaporisation (C) Viscosity (D) Specific vapor volume

Last Answer : (C) Viscosity

A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co-efficient and fi° is the fugacity of the pure component i. the Ki value (Yi = Ki xi) is therefore, in general a function of (A) Temperature only (B) Temperature and pressure only (C) Temperature, pressure and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Description : A reasonably general expression for vapour-liquid phase equilibrium at low to moderate pressure is φi yi P = Yi xifi° where, Φ is a vapor fugacity component, Yiis the liquid activity co- ... and liquid composition xi only (D) Temperature, pressure, liquid composition xi and vapour composition yi

Last Answer : (C) Temperature, pressure and liquid composition xi only

The sensitiveness of a level tube decreases if (A) Radius of curvature of its inner surface is increased (B) Diameter of the tube is increased (C) Length of the vapour bubble is increased (D) Both viscosity and surface tension are increased

Description : The sensitiveness of a level tube decreases if (A) Radius of curvature of its inner surface is increased (B) Diameter of the tube is increased (C) Length of the vapour bubble is increased (D) Both viscosity and surface tension are increased

Last Answer : (D) Both viscosity and surface tension are increased

Plate towers are preferred to packed towers, when large temperature changes are involved, because of the reason that the (A) Packing may be crushed due to thermal expansion/contraction of the components of the equipments (B) Pressure drop in the equipment will be very high (C) Viscosity variation of the fluids may cause channelling/flooding (D) None of these

Description : Plate towers are preferred to packed towers, when large temperature changes are involved, because of the reason that the (A) Packing may be crushed due to thermal expansion/contraction of the ... C) Viscosity variation of the fluids may cause channelling/flooding (D) None of these

Last Answer : (A) Packing may be crushed due to thermal expansion/contraction of the components of the equipments

Co-efficient of thermal expansion of glass is decreased by the addition of __________ during its manufacture. (A) CaO (B) MnO2 (C) ZnO (D) FeS

Description : Co-efficient of thermal expansion of glass is decreased by the addition of __________ during its manufacture. (A) CaO (B) MnO2 (C) ZnO (D) FeS

Last Answer : (C) ZnO

The expression, nCv(T2- T1), is for the __________ of an ideal gas. (A) Work done under adiabatic condition (B) Co-efficient of thermal expansion (C) Compressibility (D) None of these

Description : The expression, nCv(T2- T1), is for the __________ of an ideal gas. (A) Work done under adiabatic condition (B) Co-efficient of thermal expansion (C) Compressibility (D) None of these

Last Answer : (A) Work done under adiabatic condition

The expression, nRT ln(P1/P2), is for the __________of an ideal gas. (A) Compressibility (B) Work done under adiabatic condition (C) Work done under isothermal condition (D) Co-efficient of thermal expansion

Description : The expression, nRT ln(P1/P2), is for the __________of an ideal gas. (A) Compressibility (B) Work done under adiabatic condition (C) Work done under isothermal condition (D) Co-efficient of thermal expansion

Last Answer : C) Work done under isothermal condition

Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Description : Steel rods are normally used for concrete reinforcement because concrete and steel have almost equal (A) Tensile strength (B) Compressive strength (C) Young's modulus (D) Thermal co-efficient of expansion

Last Answer : (D) Thermal co-efficient of expansion

The pressure co-efficient is the ratio of pressure forces to __________ forces. (A) Viscous (B) Inertial (C) Gravity (D) Surface tension

Description : The pressure co-efficient is the ratio of pressure forces to __________ forces. (A) Viscous (B) Inertial (C) Gravity (D) Surface tension

Last Answer : (A) Viscous

Metallic surveying tapes are made of __________ which has a low co efficient of expansion & enough strength. (A) Invar (B) Hastelloy (C) Duralumin (D) Monel metal

Description : Metallic surveying tapes are made of __________ which has a low co efficient of expansion & enough strength. (A) Invar (B) Hastelloy (C) Duralumin (D) Monel metal

Last Answer : (A) Invar

Power consumption during turbulent flow in agitation tank is proportional to the __________ of the liquid. (A) Viscosity (B) Thermal conductivity(C) Surface tension(D) Density

Description : Power consumption during turbulent flow in agitation tank is proportional to the __________ of the liquid. (A) Viscosity (B) Thermal conductivity (C) Surface tension (D) Density

Last Answer : (D) Density

Rate of heat transfer by vaporisation from pools of water is affected by the (A) Nature of heating surface and distribution of bubbles (B) Surface tension of water (C) Viscosity of water (D) All (A), (B) and (C)

Description : Rate of heat transfer by vaporisation from pools of water is affected by the (A) Nature of heating surface and distribution of bubbles (B) Surface tension of water (C) Viscosity of water (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Which one of the following can truthfully be said of non-school, active agencies of social interaction? Options: A) The less education people have, the more they use established recreational agencies B) The largest items of the expenditure for leisure time activities are for those of a passive nature C) Adult sponsorship of youth serving organizations has proved undesirable D) The community council should conduct activities, not just to co-ordinate them

Description : Which one of the following can truthfully be said of non-school, active agencies of social interaction? Options: A) The less education people have, the more they use established recreational ... has proved undesirable D) The community council should conduct activities, not just to co-ordinate them

Last Answer : B) The largest items of the expenditure for leisure time activities are for those of a passive nature

The fluid property, due to which, mercury does not wet the glass is (A) Surface tension (B) Viscosity (C) Cohesion (D) Adhesion

Description : The fluid property, due to which, mercury does not wet the glass is (A) Surface tension (B) Viscosity (C) Cohesion (D) Adhesion

Last Answer : (A) Surface tension

The fluid property, due to which, mercury does not wet the glass is (A) Surface tension (B) Viscosity (C) Cohesion (D) Adhesion

Description : The fluid property, due to which, mercury does not wet the glass is (A) Surface tension (B) Viscosity (C) Cohesion (D) Adhesion

Last Answer : (A) Surface tension

Sudden temperature fluctuation does not affect pyrex glass, because of its (A) Low co-efficient of expansion (B) High co-efficient of expansion (C) High melting point (D) Both (B) and (C)

Description : Sudden temperature fluctuation does not affect pyrex glass, because of its (A) Low co-efficient of expansion (B) High co-efficient of expansion (C) High melting point (D) Both (B) and (C)

Last Answer : (A) Low co-efficient of expansion

Which of the following is an undesirable property in a tower packing? (A) Large surface per unit volume (B) Large free cross-section (C) Low weight per unit volume (D) Large weight of liquid retained

Description : Which of the following is an undesirable property in a tower packing? (A) Large surface per unit volume (B) Large free cross-section (C) Low weight per unit volume (D) Large weight of liquid retained

Last Answer : (D) Large weight of liquid retained

Alcohol is used in manometers because (A) It has low vapour pressure (B) It is clearly visible (C) It has low surface tension (D) It can provide longer column due to low density

Description : Alcohol is used in manometers because (A) It has low vapour pressure (B) It is clearly visible (C) It has low surface tension (D) It can provide longer column due to low density

Last Answer : Answer: Option D

Dielectric (A) Is an electrical insulating material (B) Of low resistivity is preferred (C) Should have high thermal conductivity (D) Need not defy the corrosive action of chemicals

Description : Dielectric (A) Is an electrical insulating material (B) Of low resistivity is preferred (C) Should have high thermal conductivity (D) Need not defy the corrosive action of chemicals

Last Answer : (A) Is an electrical insulating material

Spherical shape of mercury droplets is due to its (A) High viscosity (B) Low surface tension (C) High density (D) High surface tension

Description : Spherical shape of mercury droplets is due to its (A) High viscosity (B) Low surface tension (C) High density (D) High surface tension

Last Answer : Option D

Relative lowering of vapour pressure is a colligative property because_____________. (a)It depends on the concentration of a non electrolyte solute in solution and does not depend on the nature of the solute molecules. (b)It does not depends on number of particles of electrolyte solute in solution and does not depend on the nature of the solute particles. (c)It depends on the concentration of a non electrolyte solute in solution as well as on the nature of the solute molecules. (d)It depends on the concentration of an electrolyte or nonelectrolyte solutein solution as well as on the nature of solute molecules.

Description : Relative lowering of vapour pressure is a colligative property because_____________. (a)It depends on the concentration of a non electrolyte solute in solution and does not depend on the nature of ... of an electrolyte or nonelectrolyte solutein solution as well as on the nature of solute molecules.

Last Answer : (a)It depends on the concentration of a non electrolyte solute in solution and does not depend on the nature of the solute molecules.

Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a shell and tube heat exchanger (C) Steam jet ejector is used for vapor compression in a thermal recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Description : Pick out the wrong statement: (A) The capacity of an evaporator is reduced by the boiling point elevation (B) Corrosive liquid is normally passed through the tubes in a ... recompression evaporator (D) Heat sensitive materials should be concentrated in high pressure evaporators

Last Answer : (D) Heat sensitive materials should be concentrated in high pressure evaporators

During the manufacture of sulphuric acid, the temperature of molten sulphur is not increased beyond 160°C, as (A) It is very corrosive at elevated temperature (B) Its viscosity is not reduced on further heating (hence pressure drop on pumping it, cannot be further reduced) (C) It decomposes on further increasing the temperature (D) None of these

Description : During the manufacture of sulphuric acid, the temperature of molten sulphur is not increased beyond 160°C, as (A) It is very corrosive at elevated temperature (B) Its viscosity is not reduced on ... be further reduced) (C) It decomposes on further increasing the temperature (D) None of these

Last Answer : (B) Its viscosity is not reduced on further heating (hence pressure drop on pumping it, cannot be further reduced)

Soldering of two metals is possible because of the property of – (1) Viscosity (2) Osmosis (3) Cohesion (4) Surface tension

Description : Soldering of two metals is possible because of the property of – (1) Viscosity (2) Osmosis (3) Cohesion (4) Surface tension

Last Answer : (3) Cohesion Explanation: Soldering is the process of joining two metals by the use of a solder alloy, and it is one of the oldest known joining techniques. It is possible because of the ... through-out the interior of substance. Soldering leads to alloy formation at the layer between two metals.

Falling drops of water become spheres due to the property of (A) Surface tension of water (B) Compressibility of water (C) Capillarity of water (D) Viscosity of water

Description : Falling drops of water become spheres due to the property of (A) Surface tension of water (B) Compressibility of water (C) Capillarity of water (D) Viscosity of water

Last Answer : Answer: Option A

The property of a liquid which offers resistance to the movement of one layer of liquid over another adjacent layer of liquid, is called (A) Surface tension (B) Compressibility (C) Capillarity (D) Viscosity

Description : The property of a liquid which offers resistance to the movement of one layer of liquid over another adjacent layer of liquid, is called (A) Surface tension (B) Compressibility (C) Capillarity (D) Viscosity

Last Answer : Answer: Option D