For grinding of softer materials, the grinding wheel should have __________ grain size. (A) Finer (B) Coarser (C) Medium (D) Any type of

For grinding of softer materials, the grinding wheel should have __________ grain size.
(A) Finer
(B) Coarser
(C) Medium
(D) Any type of
by

1 Answer

Answer :

(B) Coarser
by

Related questions

As the product becomes finer, the energy required for grinding (A) Decreases (B) Increases (C) Is same as for coarser grinding (D) Is 1.5 times that for coarser grinding

Description : As the product becomes finer, the energy required for grinding (A) Decreases (B) Increases (C) Is same as for coarser grinding (D) Is 1.5 times that for coarser grinding

Last Answer : (B) Increases

Rapid hardening cement attains early strength due to (A) Larger proportion of lime grounded finer than normal cement (B) Lesser proportion of lime grounded coarser than normal cement (C) Lesser proportion of lime grounded finer than normal cement (D) Excess percentage of gypsum

Description : Rapid hardening cement attains early strength due to (A) Larger proportion of lime grounded finer than normal cement (B) Lesser proportion of lime grounded coarser than normal cement (C) Lesser proportion of lime grounded finer than normal cement (D) Excess percentage of gypsum

Last Answer : Answer: Option A

In case of grinding in a ball mill (A) Wet grinding achieves a finer product size than dry grinding (B) Its capacity decreases with increasing fineness of the products (C) Grinding cost and power requirement increases with increasing fineness of the products (D) All (A), (B) and (C)

Description : In case of grinding in a ball mill (A) Wet grinding achieves a finer product size than dry grinding (B) Its capacity decreases with increasing fineness of the products (C) Grinding cost and power requirement increases with increasing fineness of the products (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Use of grinding aids results in the (A) Enhanced production rate (B) Finer products (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Use of grinding aids results in the (A) Enhanced production rate (B) Finer products (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

A dense structure of grinding wheel is not used for the (A) Ductile material (B) Hard materials (C) Brittle materials (D) Finishing cuts

Description : A dense structure of grinding wheel is not used for the (A) Ductile material (B) Hard materials (C) Brittle materials (D) Finishing cuts

Last Answer : A) Ductile material

The high strength of rapid hardening cement at early stage, is due to its (A) Finer grinding (B) Burning at high temperature (C) Increased lime cement (D) Higher content of tricalcium

Description : The high strength of rapid hardening cement at early stage, is due to its (A) Finer grinding (B) Burning at high temperature (C) Increased lime cement (D) Higher content of tricalcium

Last Answer : Answer: Option C

Finer grinding of cement (A) Affects only the early development of strength (B) Affects only the ultimate strength (C) Both (A) and (B) (D) Does not affect the strength

Description : Finer grinding of cement (A) Affects only the early development of strength (B) Affects only the ultimate strength (C) Both (A) and (B) (D) Does not affect the strength

Last Answer : Answer: Option A

Early attainment of strength in rapid hardening cement is mainly due to (A) Gypsum (B) Finer grinding (C) Tri-calcium silicate (D) Tri-calcium aluminate

Description : Early attainment of strength in rapid hardening cement is mainly due to (A) Gypsum (B) Finer grinding (C) Tri-calcium silicate (D) Tri-calcium aluminate

Last Answer : Answer: Option B

Rapid gravity filters (A) Were developed by G.W. Fuller (B) Make use of coarser sand with effective size as 0.5 mm (C) Yield as high as 30 times the yield of slow sand filters (D) All the above

Description : Rapid gravity filters  (A) Were developed by G.W. Fuller  (B) Make use of coarser sand with effective size as 0.5 mm  (C) Yield as high as 30 times the yield of slow sand filters  (D) All the above 

Last Answer : (D) All the above 

The risk of segregation is more for (A) Wetter mix (B) Larger proportion of maximum size aggregate (C) Coarser grading (D) All the above

Description : The risk of segregation is more for (A) Wetter mix (B) Larger proportion of maximum size aggregate (C) Coarser grading (D) All the above

Last Answer : Answer: Option D

In which of the following cases, kinetic energy is being used in performing work? (1) Paddling the bicycle to cover a distance (2) Driving a car to cover a distance (3) Wind mill grinding wheat grain (4) Rowing a boat in the lake

Description : In which of the following cases, kinetic energy is being used in performing work? (1) Paddling the bicycle to cover a distance (2) Driving a car to cover a distance (3) Wind mill grinding wheat grain (4) Rowing a boat in the lake

Last Answer : (2) Driving a car to cover a distance Explanation: The work done on any object goes into changing the kinetic energy of that object. Since the work done by the car engine is equal to the change in ... defined as the work needed to accelerate a body of a given mass from rest to its stated velocity.

In which of the following cases, kinetic energy is being used in performing work ? (1) Paddling the bicycle to cover a distance (2) Driving a car to cover a distance (3) Wind mill grinding wheat grain (4) Rowing a boat in the lake

Description : In which of the following cases, kinetic energy is being used in performing work ? (1) Paddling the bicycle to cover a distance (2) Driving a car to cover a distance (3) Wind mill grinding wheat grain (4) Rowing a boat in the lake

Last Answer : Driving a car to cover a distance

A tube mill as compared to a ball mill (A) Employs smaller balls (B) Gives finer size reduction but consumes more power (C) Has larger length/diameter ratio (>2 as compared to 1 for ball mill) (D) All (A), (B) and (C)

Description : A tube mill as compared to a ball mill (A) Employs smaller balls (B) Gives finer size reduction but consumes more power (C) Has larger length/diameter ratio (>2 as compared to 1 for ball mill) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Powdery materials can be guarded against caking tendency on storage by (A) Providing irregular grain size (B) Providing minimum percentage of voids (C) Having maximum possible points of contact (D) None of these

Description : Powdery materials can be guarded against caking tendency on storage by (A) Providing irregular grain size (B) Providing minimum percentage of voids (C) Having maximum possible points of contact (D) None of these

Last Answer : (D) None of these

Dislocation cross-slip is difficult in those materials, which have (A) Large number of slip systems (B) High work hardening rate (C) Coarse grain size (D) Low stacking fault energy

Description : Dislocation cross-slip is difficult in those materials, which have (A) Large number of slip systems (B) High work hardening rate (C) Coarse grain size (D) Low stacking fault energy

Last Answer : (D) Low stacking fault energy

__________ conveyor is the most suitable for short distance transportation of non-abrasive loose materials like garbage, grain, food wastes etc. (A) Flight (B) Screw (C) Drag (D) Belt

Description : __________ conveyor is the most suitable for short distance transportation of non-abrasive loose materials like garbage, grain, food wastes etc. (A) Flight (B) Screw (C) Drag (D) Belt

Last Answer : (A) Flight

A grinding wheel rotates at 3000 rpm. When power supply is cut off the wheel stops in 5 sec. The number of revolutions made by the wheel before coming to rest would be a.500 b.107 dynes c.250 d.3000 e.1000

Description : A grinding wheel rotates at 3000 rpm. When power supply is cut off the wheel stops in 5 sec. The number of revolutions made by the wheel before coming to rest would be a.500 b.107 dynes c.250 d.3000 e.1000

Last Answer : c. 250

A grinding wheel rotates at 3000 rpm. When power supply is cut-off the wheel stops in 10 seconds. The number of revolutions made by the wheel before coming to rest would be a.1500 b.3000 c.1000 d.250 e.500

Description : A grinding wheel rotates at 3000 rpm. When power supply is cut-off the wheel stops in 10 seconds. The number of revolutions made by the wheel before coming to rest would be a.1500 b.3000 c.1000 d.250 e.500

Last Answer : d. 250

A grinding wheel is rotating at 3000 rpm. When the switch is turned off the wheel stops in 10 seconds. The uniform deceleration of the wheel was a.1 rad/s2 b.31.4 rad/s2 c.4 rad/s2 d.62.8 rad/s2 e.10.4 rad/s2

Description : A grinding wheel is rotating at 3000 rpm. When the switch is turned off the wheel stops in 10 seconds. The uniform deceleration of the wheel was a.1 rad/s2 b.31.4 rad/s2 c.4 rad/s2 d.62.8 rad/s2 e.10.4 rad/s2

Last Answer : b. 31.4 rad/s2

Should I use a diamond grinding wheel for cutting ceramic tile?

Description : Should I use a diamond grinding wheel for cutting ceramic tile?

Last Answer : Use a wheel specifically rated for grinding concrete or ceramic tile. It doesn't have to be a diamond wheel; titanium-coated, tungsten-coated or carbide coated wheels will also work.

A tube mill compared to a ball mill (A) Has a higher length/diameter ratio(B) Produces a coarser product(C) Has a higher diameter/length ratio(D) Uses much larger balls

Description : A tube mill compared to a ball mill (A) Has a higher length/diameter ratio (B) Produces a coarser product (C) Has a higher diameter/length ratio (D) Uses much larger balls

Last Answer : (A) Has a higher length/diameter ratio

__________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Description : __________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Last Answer : (B) Minimum size

In a grinding operation, the limiting particle size is the size of the __________ particle in the sample. (A) Smallest (B) Largest (C) Either (A) or (B) (D) Neither (A) nor (B)

Description : In a grinding operation, the limiting particle size is the size of the __________ particle in the sample. (A) Smallest (B) Largest (C) Either (A) or (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should be multiplied with __________ to get the same for dry grinding. (A) 1.0 (B) 0.5 (C) 1.34 (D) 4.34

Description : Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should ... to get the same for dry grinding. (A) 1.0 (B) 0.5 (C) 1.34 (D) 4.34

Last Answer : (C) 1.34

A pebble mill (A) Is a ball mill (B) Employs flints or ceramic pebbles as the grinding medium (C) Is a tube mill lined with ceramic or other non-metallic liner (D) Both (B) and (C)

Description : A pebble mill (A) Is a ball mill (B) Employs flints or ceramic pebbles as the grinding medium (C) Is a tube mill lined with ceramic or other non-metallic liner (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Description : Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Which of the following crushing laws is most accurately applicable to the fine grinding of materials? (A) Bond's crushing law (B) Kick's law (C) Rittinger's law (D) None of these

Description : Which of the following crushing laws is most accurately applicable to the fine grinding of materials? (A) Bond's crushing law (B) Kick's law (C) Rittinger's law (D) None of these

Last Answer : (C) Rittinger's law

Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure drop (C) Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Description : Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure ... Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Last Answer : (B) Cake resistance is independent of the pressure drop

hich of the following is the most suitable abrasive for grinding high tensile strength materials? (A) Silicon carbide (B) Corundum (C) Aluminium oxide (D) Boron carbide

Description : hich of the following is the most suitable abrasive for grinding high tensile strength materials? (A) Silicon carbide (B) Corundum (C) Aluminium oxide (D) Boron carbide

Last Answer : Option C

Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Description : Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Last Answer : a) Fluted wheel

The admixture of coarser particles like sand or silt to clay causes (A) Decrease in liquid limit and increase in plasticity index (B) Decrease in liquid limit and no change in plasticity index (C) Decrease in both liquid limit and plasticity index (D) Increase in both liquid limit and plasticity index

Description : The admixture of coarser particles like sand or silt to clay causes (A) Decrease in liquid limit and increase in plasticity index (B) Decrease in liquid limit and no change in plasticity index ... in both liquid limit and plasticity index (D) Increase in both liquid limit and plasticity index

Last Answer : Answer: Option C

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (C) Creep resistance

Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Description : Reduction in the grain size reduces the __________ of the material. (A) Fatigue resistance (B) Tensile strength (C) Creep resistance (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Tube mill compared to ball mill (A) Produces finer products (B) Is long in comparison with its diameter (C) Uses smaller balls (D) All (A), (B) & (C)

Description : Tube mill compared to ball mill (A) Produces finer products (B) Is long in comparison with its diameter (C) Uses smaller balls (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Which of the following materials is recommended for finishing the slip rings after grinding or turning? A. grade 00 sandpaper B. canvas wiper C. crocus cloth D. smooth file

Description : Which of the following materials is recommended for finishing the slip rings after grinding or turning? A. grade 00 sandpaper B. canvas wiper C. crocus cloth D. smooth file

Last Answer : Answer: C

Synthetic rubber (A) Deforms, if stretched to double of its original dimension (B) Is brittle at low temperature (C) Is softer at higher temperature (D) Is highly permeable to air & water and is readily attacked by chemicals & atmospheric gases

Description : Synthetic rubber (A) Deforms, if stretched to double of its original dimension (B) Is brittle at low temperature (C) Is softer at higher temperature (D) Is highly permeable to air & water and is readily attacked by chemicals & atmospheric gases

Last Answer : (D) Is highly permeable to air & water and is readily attacked by chemicals & atmospheric gases

Preheating before welding is done to (A) Make the plate softer (B) Burn oil & grease sticking to plate surfaces (C) Avoid plate distortion (D) Prevent cold cracks

Description : Preheating before welding is done to (A) Make the plate softer (B) Burn oil & grease sticking to plate surfaces (C) Avoid plate distortion (D) Prevent cold cracks

Last Answer : (D) Prevent cold cracks

Which one of the following statements is NOT correct? [IAS 2003] (a) Black cotton soil of north-west India was formed by the weathering of basaltic lava rocks (b) Sedimentary rocks are distinguished from other types of rocks by the presence of distinct layers (c) Granite has large crystals of quartz, feldspar and mica in it (d) A metamorphic rock is softer and less compact than its original type

Description : Which one of the following statements is NOT correct? [IAS 2003] (a) Black cotton soil of north-west India was formed by the weathering of basaltic lava rocks (b) Sedimentary rocks are distinguished ... feldspar and mica in it (d) A metamorphic rock is softer and less compact than its original type

Last Answer : Ans: (d)

Pick out the wrong statement. (A) Close circuit grinding is more economical than open circuit grinding (B) Cod oil, beef tallow or aluminium stearates are used as grinding aids in cement 'industries' (C) The equipment used for the removal of traces of solids from a liquid is called a classifier (D) Size enlargement is a mechanical operation exemplified by medicinal tablet making

Description : Pick out the wrong statement. (A) Close circuit grinding is more economical than open circuit grinding (B) Cod oil, beef tallow or aluminium stearates are used as grinding aids in cement ... is called a classifier (D) Size enlargement is a mechanical operation exemplified by medicinal tablet making

Last Answer : (C) The equipment used for the removal of traces of solids from a liquid is called a classifier

For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a(A) Buhrstone mill(B) Ball mill(C) Crushing rolls(D) Hammer mill

Description : For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a (A) Buhrstone mill (B) Ball mill (C) Crushing rolls (D) Hammer mill

Last Answer : (A) Buhrstone mill

The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed(C) Clearance between hammer & grinding plates(D) All (A), (B) and (C

Description : In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed (C) Clearance between hammer & grinding plates (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

The main differentiation factor between tube mill and ball mill is the (A) Length to diameter ratio (B) Size of the grinding media (C) Final product size (D) Operating speed

Description : The main differentiation factor between tube mill and ball mill is the (A) Length to diameter ratio (B) Size of the grinding media (C) Final product size (D) Operating speed

Last Answer : (A) Length to diameter ratio

In closed circuit grinding as compared to open circuit grinding, the (A) Specific surface of product is more (B) Product has lesser size uniformity (C) Production rate at a given limiting size is lower (D) Operation is economical

Description : In closed circuit grinding as compared to open circuit grinding, the (A) Specific surface of product is more (B) Product has lesser size uniformity (C) Production rate at a given limiting size is lower (D) Operation is economical

Last Answer : (D) Operation is economical

Which of the following size reduction equipments employs mainly attrition for ultrafine grinding? (A) Jet mills (B) Fluid energy mill (C) Micronizer (D) All (A), (B) and (C)

Description : Which of the following size reduction equipments employs mainly attrition for ultrafine grinding? (A) Jet mills (B) Fluid energy mill (C) Micronizer (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Is it okay to use medium grain Japanese rice for fried rice?

Description : Is it okay to use medium grain Japanese rice for fried rice?

Last Answer : Sure. You can use anything really.

Colloidal mills are used for __________ grinding. (A) Coarse (B) Intermediate (C) Fine (D) Ultrafine

Description : Colloidal mills are used for __________ grinding. (A) Coarse (B) Intermediate (C) Fine (D) Ultrafine

Last Answer : (D) Ultrafine

3. __________ mill is normally used for grinding of talc. (A) Tube (B) Compartment (C) Ring-roll (D) Pebble

Description : 3. __________ mill is normally used for grinding of talc. (A) Tube (B) Compartment (C) Ring-roll (D) Pebble

Last Answer : (A) Tube

A __________ mill is a revolving mill divided into two or more sections by perforated partitions in which preliminary grinding takes place at one end and the finishing grinding at the discharge end. (A) Compartment (B) Tube (C) Rod (D) Pebble

Description : A __________ mill is a revolving mill divided into two or more sections by perforated partitions in which preliminary grinding takes place at one end and the finishing grinding at the discharge end. (A) Compartment (B) Tube (C) Rod (D) Pebble

Last Answer : (A) Compartmen

__________ mill is not used for grinding wheat into flour and for milling of cereals & other vegetable products. (A) Buhrstone (B) Roller (C) Attrition (D) Pebble

Description : __________ mill is not used for grinding wheat into flour and for milling of cereals & other vegetable products. (A) Buhrstone (B) Roller (C) Attrition (D) Pebble

Last Answer : (D) Pebble