Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should be multiplied with __________ to get the same for dry grinding. (A) 1.0 (B) 0.5 (C) 1.34 (D) 4.34

Work index is the gross energy (kWh/tonne of feed) necessary to reduce
a very large feed to such a size that 80% of product particles will pass
through a 0.1 mm screen. The value of work index determined for wet
grinding should be multiplied with __________ to get the same for dry
grinding.
(A) 1.0
(B) 0.5
(C) 1.34
(D) 4.34
by

1 Answer

Answer :

(C) 1.34
by

Related questions

Work index is defined as the (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen (B) Energy needed to crush one tonne of feed to 200 microns (C) Energy (kWh/ton of feed) needed to crush small feed to such a size that 80% of the product passes a 200 mesh screen (D) Energy needed to crush one ton of feed to 100 microns

Description : Work index is defined as the (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen (B) Energy needed to crush ... of the product passes a 200 mesh screen (D) Energy needed to crush one ton of feed to 100 microns

Last Answer : (A) Gross energy (kWh/ton of feed) needed to reduce very large feed to such a size that 80% of the product passes through a 100 micron screen

Pick out the correct statement. (A) Plastic chips are called non-cohesive solids (B) Kick's crushing law is, P/m = K . ln (D̅sa /Ds̅b ) (C) Communition is a generic term for size enlargement operation (D) Energy required in kwh per ton of product, such that 80% of it passes through a 200 mesh screen, is called 'Work index'

Description : Pick out the correct statement. (A) Plastic chips are called non-cohesive solids (B) Kick's crushing law is, P/m = K . ln (D̅sa /Ds̅b ) (C) Communition is a generic term for size enlargement ... per ton of product, such that 80% of it passes through a 200 mesh screen, is called 'Work index'

Last Answer : (B) Kick's crushing law is, P/m = K . ln (D̅sa /Ds̅b )

Actual operating speed of a ball mill may vary from 65 to 80% of the critical speed. Which of the following duties would require the ball mill to be operated at maximum percentage of critical speed? (A) Wet grinding in low viscous suspension (B) Wet grinding in high viscous suspension (C) Dry grinding of large particles (upto 1.25 cms) (D) Dry grinding of large particles in un-baffed mills

Description : Actual operating speed of a ball mill may vary from 65 to 80% of the critical speed. Which of the following duties would require the ball mill to be operated at maximum percentage of critical speed? (A) ... of large particles (upto 1.25 cms) (D) Dry grinding of large particles in un-baffed mills

Last Answer : (D) Dry grinding of large particles in un-baffed mills

The value of work index does not change materially from one equipment to another. If the value of work index determined for close circuit grinding is Wi, then the same for open circuit grinding will be (A) 0.5 Wi (B) Wi (C) 1.34 Wi (D) 3.34 Wi

Description : The value of work index does not change materially from one equipment to another. If the value of work index determined for close circuit grinding is Wi, then the same for open circuit grinding will be (A) 0.5 Wi (B) Wi (C) 1.34 Wi (D) 3.34 Wi

Last Answer : (C) 1.34 Wi

The energy required per unit mass to grind limestone particles of very large size to 100 μm is 12.7 kWh/ton. An estimate (using Bond's law) of the energy to grind the particles from a very large size to 50 μm is (A) 6.35 kWh/ton (B) 9.0 kWh/ton (C) 18 kWh/ton (D) 25.4 kWh/ton

Description : The energy required per unit mass to grind limestone particles of very large size to 100 μm is 12.7 kWh/ton. An estimate (using Bond's law) of the energy to grind the particles from a very large size to 50 μm is (A) 6.35 kWh/ton (B) 9.0 kWh/ton (C) 18 kWh/ton (D) 25.4 kWh/ton

Last Answer : (C) 18 kWh/ton

Wet grinding in a revolving mill __________ as compared to dry grinding. (A) Gives less wear on chamber walls (B) Requires more energy (C) Increases capacity (D) Complicates handling of the product

Description : Wet grinding in a revolving mill __________ as compared to dry grinding. (A) Gives less wear on chamber walls (B) Requires more energy (C) Increases capacity (D) Complicates handling of the product

Last Answer : (C) Increases capacity

Bond crushing law (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law (B) Is less realistic in estimating the power requirements of commercial crushers (C) States that the work required to form particle of any size from very large feed is proportional to the square root of the volume to surface ratio of the product (D) States that the work required for the crushing is proportional to the new surface created

Description : Bond crushing law (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law (B) Is less realistic in estimating the power requirements of commercial crushers ( ... (D) States that the work required for the crushing is proportional to the new surface created

Last Answer : (A) Calls for relatively less energy for the smaller product particles, than does the Rittinger law

In case of grinding in a ball mill (A) Wet grinding achieves a finer product size than dry grinding (B) Its capacity decreases with increasing fineness of the products (C) Grinding cost and power requirement increases with increasing fineness of the products (D) All (A), (B) and (C)

Description : In case of grinding in a ball mill (A) Wet grinding achieves a finer product size than dry grinding (B) Its capacity decreases with increasing fineness of the products (C) Grinding cost and power requirement increases with increasing fineness of the products (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In case of a revolving mill, wet grinding compared to dry grinding (A) Requires more energy (B) Has less capacity (C) Complicates handling & classification of the product (D) None of these

Description : In case of a revolving mill, wet grinding compared to dry grinding (A) Requires more energy (B) Has less capacity (C) Complicates handling & classification of the product (D) None of these

Last Answer : (D) None of these

The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Use of 'grinding aids' is done in __________ grinding. (A) Dry (B) Wet (C) Ultrafine (D) Intermediate

Description : Use of 'grinding aids' is done in __________ grinding. (A) Dry (B) Wet (C) Ultrafine (D) Intermediate

Last Answer : (A) Dry

Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size (C) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size

In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed(C) Clearance between hammer & grinding plates(D) All (A), (B) and (C

Description : In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed (C) Clearance between hammer & grinding plates (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

__________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Description : __________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Last Answer : (B) Minimum size

For achieving rapid drying rate in a spray dryer, the diameter of the particles in the feed should be in the range of __________ microns (1 mm = 1000 microns). (A) 1-5 (B) 10-60 (C) 200-300

Description : For achieving rapid drying rate in a spray dryer, the diameter of the particles in the feed should be in the range of __________ microns (1 mm = 1000 microns). (A) 1-5 (B) 10-60 (C) 200-300

Last Answer : (B) 10-60

In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine

Description : In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine

Last Answer : (C) Fine

In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine

Last Answer : (B) Secondary

In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine

Description : In a size reduction crushing operation, feed size is 300 to 1500 mm while the product size is 100 to 300 mm. This is a case of the __________ crushing. (A) Secondary (B) Fine (C) Primary (D) Ultrafine

Last Answer : (C) Primary

Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will just take hold of a particle and draw it in the crushing zone (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing (D) Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Description : Pick out the wrong statement. (A) Gape is the greatest distance between the crushing surfaces or the jaws (B) The angle of nip (2α) is the angle between roll faces at the level where they will ... Reduction ratio is the ratio of the maximum size of the particles in the feed to that in the product

Last Answer : (C) Crushing efficiency is the ratio of the energy absorbed by the solid to the surfaces energy created by crushing

According to Bond crushing law, the work required to form particle of size 'D' from very large feed is (where (S/V)p and (S/V) f are surface to volume ratio of the product and feed respectively). (A) (S/V)p (B) √(S/V)p (C) (S/V) 2 p (D) (S/V) f

Description : According to Bond crushing law, the work required to form particle of size 'D' from very large feed is (where (S/V)p and (S/V) f are surface to volume ratio of the product and feed respectively). (A) (S/V)p (B) √(S/V)p (C) (S/V) 2 p (D) (S/V) f

Last Answer : (B) √(S/V)

If the gross vehicle weight of a truck is 30 tonne and rolling resistance is 30 kg/tonne, then the tractive effort required to keep the truck moving at a uniform speed is (A) 30 kg (B) 300 kg (C) 900 kg (D) 1000 kg

Description : If the gross vehicle weight of a truck is 30 tonne and rolling resistance is 30 kg/tonne, then the tractive effort required to keep the truck moving at a uniform speed is (A) 30 kg (B) 300 kg (C) 900 kg (D) 1000 kg

Last Answer : (C) 900 kg

Explain the following a) Dry Bulb Temperature and Wet bulb Temperature b) Maximum Demand and Power Factor c) Gross Calorific Value & Net Calorific Value d) 5S & Return of Investment (ROI) e) CUSUM

Description : Explain the following a) Dry Bulb Temperature and Wet bulb Temperature b) Maximum Demand and Power Factor c) Gross Calorific Value & Net Calorific Value d) 5S & Return of Investment (ROI) e) CUSUM

Last Answer : a) Dry Bulb Temperature and Wet bulb Temperature Dry bulb Temperature is an indication of the sensible heat content of air-water vapour  mixtures Wet bulb Temperature is a measure of ... of capital cost. This is a broad indicator of the annual return expected from initial capital investment

In screen analysis, the notation +5 mm/-10 mm means particles passing through (A) 10 mm screen and retained on 5 mm screen (B) 5 mm screen and retained on 10 mm screen (C) Both 5 mm and 10 mm screens (D) Neither 5 mm nor 10 mm screen

Description : In screen analysis, the notation +5 mm/-10 mm means particles passing through (A) 10 mm screen and retained on 5 mm screen (B) 5 mm screen and retained on 10 mm screen (C) Both 5 mm and 10 mm screens (D) Neither 5 mm nor 10 mm screen

Last Answer : (A) 10 mm screen and retained on 5 mm screen

The capillary rise of water (A) Depends upon the force responsible (B) Increases as the size of the soil particles increases (C) Decreases as the size of the soil particles decreases (D) Is less in wet soil than in dry soil

Description : The capillary rise of water (A) Depends upon the force responsible (B) Increases as the size of the soil particles increases (C) Decreases as the size of the soil particles decreases (D) Is less in wet soil than in dry soil

Last Answer : (A) Depends upon the force responsible

Wet sieving is employed, when the product contains __________ materials. (A) Abrasive (B) Large quantity of very fine (C) Coarse (D) Non-sticky

Description : Wet sieving is employed, when the product contains __________ materials. (A) Abrasive (B) Large quantity of very fine (C) Coarse (D) Non-sticky

Last Answer : (B) Large quantity of very fine

Pulverised coal passing through 200 mesh screen has a diameter of 0.074 mm (74 micron). The same passing through 50 mesh screen will have a dia of __________ mm. (A) 0.007 (B) 0.30 (C) 50 (D) 0.014

Description : Pulverised coal passing through 200 mesh screen has a diameter of 0.074 mm (74 micron). The same passing through 50 mesh screen will have a dia of __________ mm. (A) 0.007 (B) 0.30 (C) 50 (D) 0.014

Last Answer : (B) 0.30

Grindability index of a coal is 100. It implies that the (A) Coal can be pulverised with great difficulty (B) Coal can't be pulverised (C) Coal can be easily pulverised (D) Power consumption in grinding the coal will be very high

Description : Grindability index of a coal is 100. It implies that the (A) Coal can be pulverised with great difficulty (B) Coal can't be pulverised (C) Coal can be easily pulverised (D) Power consumption in grinding the coal will be very high

Last Answer : (C) Coal can be easily pulverised

or Indian standard (IS) screens, the mesh number is equal to its aperture size expressed to the nearest deca-micron (0.01 mm). Aperture width of IS screen of mesh number 50 will be approximately __________ microns. (A) 5 (B) 50 (C) 500 (D) 5000

Description : or Indian standard (IS) screens, the mesh number is equal to its aperture size expressed to the nearest deca-micron (0.01 mm). Aperture width of IS screen of mesh number 50 will be approximately __________ microns. (A) 5 (B) 50 (C) 500 (D) 5000

Last Answer : (C) 500

80% less than 200 mesh size particles are called (A) Smoke (B) Powder (C) Grit (D) Aggregates

Description : 80% less than 200 mesh size particles are called (A) Smoke (B) Powder (C) Grit (D) Aggregates

Last Answer : (B) Powder

The work index in Bond's law for crushing of solids has the following dimensions (A) No units (dimensionless) (B) kWh/ton (C) kW/ton (D) kWh.m1/2 /ton

Description : The work index in Bond's law for crushing of solids has the following dimensions (A) No units (dimensionless) (B) kWh/ton (C) kW/ton (D) kWh.m1/2 /ton

Last Answer : (B) kWh/ton

Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year showing the cost at that time relative to a certain base year (C) Turnover ratio of a chemical plant is the ratio of gross annual sales to the fixed capital investment (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Description : Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year ... butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Last Answer : (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

. In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Description : . In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Last Answer : (D) Rotor shaft carrying hammers can be vertical or horizontal

In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net settlement (i.e. total settlement minus rebound) per tonne of test load should not exceed (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Description : In testing a pile by load test, pile platform is loaded with one and half times the design load and a maximum settlement is noted. The load is gradually removed and the consequent rebound is measured. For a safe pile, the net ... load should not exceed (A) 10 mm (B) 15 mm (C) 20 mm (D) 25 mm

Last Answer : Answer: Option D

Energy consumed for crushing one ton of material ranges from __________ kWh. (A) 0.01 to 0.1 (B) 0.5 to 1.5 (C) 2 to 3.5 (D) 4 to 5

Description : Energy consumed for crushing one ton of material ranges from __________ kWh. (A) 0.01 to 0.1 (B) 0.5 to 1.5 (C) 2 to 3.5 (D) 4 to 5

Last Answer : (B) 0.5 to 1.5

For a cement plant the parameter, ―kWh/MT of clinker ―indicates a) Energy Index parameter b) Utility factor

Description : For a cement plant the parameter, ―kWh/MT of clinker ―indicates a) Energy Index parameter b) Utility factor

Last Answer :  Energy Index parameter 

19. For a cement plant the parameter, ―kWh/MT of clinker ―indicates a) Energy Index parameter b) Utility factor c) Production factor d) Load factor

Description : For a cement plant the parameter, ―kWh/MT of clinker ―indicates a) Energy Index parameter b) Utility factor c) Production factor d) Load factor

Last Answer : Utility factor

For a cement plant the parameter, ―kWh/MT of clinker ―indicates c) Energy Index parameter c) Production factor d) Utility factor d) load factor

Description : For a cement plant the parameter, ―kWh/MT of clinker ―indicates c) Energy Index parameter c) Production factor d) Utility factor d) load factor

Last Answer :  Energy Index parameter

For a cement plant the parameter, ―kWh/MT of clinker ―indicates a) Energy Index parameter c) Production factor b) Utility factor d) load factor

Description : For a cement plant the parameter, ―kWh/MT of clinker ―indicates a) Energy Index parameter c) Production factor b) Utility factor d) load factor

Last Answer : Energy Index parameter

For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Description : For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Last Answer : (a) 1.5 mm less than the plate thickness

Moist air is cooled along the line of constant __________ , when it is passed over a cold & dry cooling coil, such that no condensation occurs? (A) Enthalpy (B) Relative humidity (C) Wet bulb temperature (D) Dew point temperature

Description : Moist air is cooled along the line of constant __________ , when it is passed over a cold & dry cooling coil, such that no condensation occurs? (A) Enthalpy (B) Relative humidity (C) Wet bulb temperature (D) Dew point temperature

Last Answer : (D) Dew point temperature

__________ temperature is the steady state temperature attained by a small amount of liquid evaporating into a large quantity of unsaturated gas￾vapor mixture. (A) Dry bulb (B) Wet bulb (C) Dew point (D) None of these

Description : __________ temperature is the steady state temperature attained by a small amount of liquid evaporating into a large quantity of unsaturated gas￾vapor mixture. (A) Dry bulb (B) Wet bulb (C) Dew point (D) None of these

Last Answer : (B) Wet bulb

Steady state temperature reached by a small amount of liquid evaporating into a large amount of unsaturated vapour-gas mixture is called the __________ temperature. (A) Dry-bulb (B) Wet-bulb (C) Dew point (D) Adiabatic saturation

Description : Steady state temperature reached by a small amount of liquid evaporating into a large amount of unsaturated vapour-gas mixture is called the __________ temperature. (A) Dry-bulb (B) Wet-bulb (C) Dew point (D) Adiabatic saturation

Last Answer : (B) Wet-bulb

The porosity of a certain soil sample was found to be 80% and its specific gravity was 2:7; the critical hydraulic gradient will be estimated as (a) 0.34 (b) 0.92 (c) 1.0 (d) 1.5

Description : The porosity of a certain soil sample was found to be 80% and its specific gravity was 2:7; the critical hydraulic gradient will be estimated as (a) 0.34 (b) 0.92 (c) 1.0 (d) 1.5

Last Answer : (a) 0.34

A tractor whose weight is 20 tonnes has a drawbar pull of 2500 kg, when operated on a level road having a rolling resistance of 30 kg per tonne. If this tractor is operated on a level road having a rolling resistance of 40 kg per tonne, then the drawbar pull of the tractor will (A) Reduce by 200 kg (B) Increase by 200 kg (C) Increase by 250 kg (D) Reduce by 250 kg

Description : A tractor whose weight is 20 tonnes has a drawbar pull of 2500 kg, when operated on a level road having a rolling resistance of 30 kg per tonne. If this tractor is operated on a level road having a rolling resistance ... 200 kg (B) Increase by 200 kg (C) Increase by 250 kg (D) Reduce by 250 kg

Last Answer : (A) Reduce by 200 kg

The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity. (A) 0 (B) 100 (C) 50 (D) None of these

Description : The wet bulb temperature is lower in dry air than in wet air at the same temperature. A dry bulb thermometer registers a higher temperature than a wet bulb thermometer except at __________ percent relative humidity. (A) 0 (B) 100 (C) 50 (D) None of these

Last Answer : Option B

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below : Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, the minimum fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle ... fluidisation velocity, VOM is (A) 12 mm/s (B) 16 mm/s (C) 24 mm/s (D) 28 mm/s

Last Answer : (B) 16 mm/s

After finishing the work by Aswin for 9 days, Ajay finds that only 1/4 of the work has been done. He employs Ajay who is 80% as efficient as Aswin. How many days more would Ajay take to complete the work? a) 32 b) 28 c) 34 d) 26

Description : After finishing the work by Aswin for 9 days, Ajay finds that only 1/4 of the work has been done. He employs Ajay who is 80% as efficient as Aswin. How many days more would Ajay take to complete the work? a) 32 b) 28 c) 34 d) 26

Last Answer : C Aswin has completed 1/4 of the work in 9 days Then he can complete the total work in 1/4 ---- 9 1 ---- ? = 36 days But given Ajay is only 80% as efficient as Aswin Ajay = 1/36*80/100=1/45 Ajay can ... work can be completed in 1 ------ 45 3/4 ------ ? =3/4*45 =33.75=34 days (approx.)

The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Description : The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Last Answer : (B) 2.5 times

When the difference in the temperature of the wet-bulb thermometer and dry-bulb thermometer is large, what does it indicate about the air? w) it is very dry x) it is nearly saturated y) it is very warm z) it is very cold

Description : When the difference in the temperature of the wet-bulb thermometer and dry-bulb thermometer is large, what does it indicate about the air? w) it is very dry x) it is nearly saturated y) it is very warm z) it is very cold

Last Answer : ANSWER: W -- IT IS VERY DRY

As the product becomes finer, the energy required for grinding (A) Decreases (B) Increases (C) Is same as for coarser grinding (D) Is 1.5 times that for coarser grinding

Description : As the product becomes finer, the energy required for grinding (A) Decreases (B) Increases (C) Is same as for coarser grinding (D) Is 1.5 times that for coarser grinding

Last Answer : (B) Increases