A tube mill compared to a ball mill (A) Has a higher length/diameter ratio(B) Produces a coarser product(C) Has a higher diameter/length ratio(D) Uses much larger balls

A tube mill compared to a ball mill
(A) Has a higher length/diameter ratio
(B) Produces a coarser product
(C) Has a higher diameter/length ratio
(D) Uses much larger balls
by

1 Answer

Answer :

(A) Has a higher length/diameter ratio
by

Related questions

A tube mill as compared to a ball mill (A) Employs smaller balls (B) Gives finer size reduction but consumes more power (C) Has larger length/diameter ratio (>2 as compared to 1 for ball mill) (D) All (A), (B) and (C)

Description : A tube mill as compared to a ball mill (A) Employs smaller balls (B) Gives finer size reduction but consumes more power (C) Has larger length/diameter ratio (>2 as compared to 1 for ball mill) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Tube mill compared to ball mill (A) Produces finer products (B) Is long in comparison with its diameter (C) Uses smaller balls (D) All (A), (B) & (C)

Description : Tube mill compared to ball mill (A) Produces finer products (B) Is long in comparison with its diameter (C) Uses smaller balls (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The main differentiation factor between tube mill and ball mill is the (A) Length to diameter ratio (B) Size of the grinding media (C) Final product size (D) Operating speed

Description : The main differentiation factor between tube mill and ball mill is the (A) Length to diameter ratio (B) Size of the grinding media (C) Final product size (D) Operating speed

Last Answer : (A) Length to diameter ratio

What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls? (A) 0.5 (B) 1.0 (C) 2.76 (D) 0.66

Description : What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls? (A) 0.5 (B) 1.0 (C) 2.76 (D) 0.66

Last Answer : (D) 0.66

Length/diameter ratio of a ball mill is (A) 1.5 (B) 1 (C) < 1 (D) > 1

Description : Length/diameter ratio of a ball mill is (A) 1.5 (B) 1 (C) < 1 (D) > 1

Last Answer : (C) < 1

__________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Description : __________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Last Answer : (B) Minimum size

A __________ mixer resembles a ball mill without balls. (A) Banbury (B) Pug mill (C) Tumbling (D) Pan

Description : A __________ mixer resembles a ball mill without balls. (A) Banbury (B) Pug mill (C) Tumbling (D) Pan

Last Answer : (C) Tumbling

In a ball mill, the volume occupied by the balls (when the mill is stopped) is about __________ percent of the volume of the mill. (A) 35 (B) 50 (C) 70 (D) 85

Description : In a ball mill, the volume occupied by the balls (when the mill is stopped) is about __________ percent of the volume of the mill. (A) 35 (B) 50 (C) 70 (D) 85

Last Answer : (B) 50

Balls in a ball mill are usually made of (A) Steel (B) Cast iron (C) Stainless steel (D) Bronze

Description : Balls in a ball mill are usually made of (A) Steel (B) Cast iron (C) Stainless steel (D) Bronze

Last Answer : (A) Steel

Tabular bowl centrifuges as compared to disk bowl centrifuges (A) Operate at higher speed (B) Employ bowl of larger diameter (C) Can’t be operated under pressure/vacuum (D) Can’t be used for separation of fine suspended solids from a liquid

Description : Tabular bowl centrifuges as compared to disk bowl centrifuges (A) Operate at higher speed (B) Employ bowl of larger diameter (C) Can’t be operated under pressure/vacuum (D) Can’t be used for separation of fine suspended solids from a liquid

Last Answer : (A) Operate at higher speed

The risk of segregation is more for (A) Wetter mix (B) Larger proportion of maximum size aggregate (C) Coarser grading (D) All the above

Description : The risk of segregation is more for (A) Wetter mix (B) Larger proportion of maximum size aggregate (C) Coarser grading (D) All the above

Last Answer : Answer: Option D

Rapid hardening cement attains early strength due to (A) Larger proportion of lime grounded finer than normal cement (B) Lesser proportion of lime grounded coarser than normal cement (C) Lesser proportion of lime grounded finer than normal cement (D) Excess percentage of gypsum

Description : Rapid hardening cement attains early strength due to (A) Larger proportion of lime grounded finer than normal cement (B) Lesser proportion of lime grounded coarser than normal cement (C) Lesser proportion of lime grounded finer than normal cement (D) Excess percentage of gypsum

Last Answer : Answer: Option A

In case of a ball mill, (A) Coarse feed requires a larger ball (B) Fine feed requires a larger ball (C) Operating speed should be more than the critical speed (D) None of these

Description : In case of a ball mill, (A) Coarse feed requires a larger ball (B) Fine feed requires a larger ball (C) Operating speed should be more than the critical speed (D) None of these

Last Answer : (A) Coarse feed requires a larger ball

Beehive coke oven (A) Facilitates by-products recovery (B) Takes 2-3 days for coking of coal but requires no external fuel for heating (C) Gives larger yield of coke (around 85%) as compared to by-product ovens (D) Produces coke with very poor strength

Description : Beehive coke oven (A) Facilitates by-products recovery (B) Takes 2-3 days for coking of coal but requires no external fuel for heating (C) Gives larger yield of coke (around 85%) as compared to by-product ovens (D) Produces coke with very poor strength

Last Answer : (B) Takes 2-3 days for coking of coal but requires no external fuel for heating

In a shell and tube heat exchanger, square pitch compared to triangular pitch (A) Gives a higher shell side pressure drop (B) Gives a lower shell side pressure drop (C) Can pack more surface area into a shell of given diameter (D) None of these

Description : In a shell and tube heat exchanger, square pitch compared to triangular pitch (A) Gives a higher shell side pressure drop (B) Gives a lower shell side pressure drop (C) Can pack more surface area into a shell of given diameter (D) None of these

Last Answer : (A) Gives a higher shell side pressure drop

Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Description : Rod mills employed for grinding (A) Employ a steel shell having L/D ratio of 1.5 to 3.0 (B) Is useful for handling sticky materials (C) Employ steel rods of 2-12 cms diameter extending over full length of the mill (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Last Answer : (B) Hammer crusher

A pebble mill (A) Is a ball mill (B) Employs flints or ceramic pebbles as the grinding medium (C) Is a tube mill lined with ceramic or other non-metallic liner (D) Both (B) and (C)

Description : A pebble mill (A) Is a ball mill (B) Employs flints or ceramic pebbles as the grinding medium (C) Is a tube mill lined with ceramic or other non-metallic liner (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

For the preliminary breaking of hard rock, we use a (A) Gyratory crusher(B) Ball mill(C) Tube mill(D) Squirrel-cage disintegrator

Description : For the preliminary breaking of hard rock, we use a (A) Gyratory crusher (B) Ball mill (C) Tube mill (D) Squirrel-cage disintegrator

Last Answer : (A) Gyratory crusher

Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Last Answer : (C) Jaw crusher

Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Last Answer : (B) Hammer crusher

Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill

Description : Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill

Last Answer : (B) Squirrel-cage disintegrator

Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Last Answer : (C) Tube mill

Power required to drive a ball mill with a particular ball load is proportional to (where, D = diameter of ball mill.) (A) D (B) 1/D (C) D2.5 (D) 1/D2.5

Description : Power required to drive a ball mill with a particular ball load is proportional to (where, D = diameter of ball mill.) (A) D (B) 1/D (C) D2.5 (D) 1/D2.5

Last Answer : (C) D2.5 (D) 1/D2

In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Description : In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Last Answer : (A) Db 2 = K.Df

Ball mills and tube mills with flint or porcelain balls are used for size reduction of (A) Asbestos (B) Rubber (C) Non-metallic ores (D) Limestone

Description : Ball mills and tube mills with flint or porcelain balls are used for size reduction of (A) Asbestos (B) Rubber (C) Non-metallic ores (D) Limestone

Last Answer : (C) Non-metallic ores

As the product becomes finer, the energy required for grinding (A) Decreases (B) Increases (C) Is same as for coarser grinding (D) Is 1.5 times that for coarser grinding

Description : As the product becomes finer, the energy required for grinding (A) Decreases (B) Increases (C) Is same as for coarser grinding (D) Is 1.5 times that for coarser grinding

Last Answer : (B) Increases

For specified tube outside diameter, higher BWG means higher (A) Tube thickness (B) Cross-sectional area (C) Weight per unit length (D) None of these

Description : For specified tube outside diameter, higher BWG means higher (A) Tube thickness (B) Cross-sectional area (C) Weight per unit length (D) None of these

Last Answer : (B) Cross-sectional area

High temperature carbonisation of coal produces (A) Inferior coke compared to low temperature carbonisation(B) Less of gases compared to liquid products(C) Larger quantity of tar compared to low temperature carbonisation(D) None of these

Description : High temperature carbonisation of coal produces (A) Inferior coke compared to low temperature carbonisation (B) Less of gases compared to liquid products (C) Larger quantity of tar compared to low temperature carbonisation (D) None of these

Last Answer : (D) None of these

Two small diameter 10gm dielectric balls can slide freely on a vertical channel. Each carry a negative charge of 1μC. Find the separation between the balls if the lower ball is restrained from moving. a) 0.5 b) 0.4 c) 0.3 d) 0.2

Description : Two small diameter 10gm dielectric balls can slide freely on a vertical channel. Each carry a negative charge of 1μC. Find the separation between the balls if the lower ball is restrained from moving. a) 0.5 b) 0.4 c) 0.3 d) 0.2

Last Answer : c) 0.3

Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

In case of grinding in a ball mill (A) Wet grinding achieves a finer product size than dry grinding (B) Its capacity decreases with increasing fineness of the products (C) Grinding cost and power requirement increases with increasing fineness of the products (D) All (A), (B) and (C)

Description : In case of grinding in a ball mill (A) Wet grinding achieves a finer product size than dry grinding (B) Its capacity decreases with increasing fineness of the products (C) Grinding cost and power requirement increases with increasing fineness of the products (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Wet grinding in a revolving mill __________ as compared to dry grinding. (A) Gives less wear on chamber walls (B) Requires more energy (C) Increases capacity (D) Complicates handling of the product

Description : Wet grinding in a revolving mill __________ as compared to dry grinding. (A) Gives less wear on chamber walls (B) Requires more energy (C) Increases capacity (D) Complicates handling of the product

Last Answer : (C) Increases capacity

In case of a revolving mill, wet grinding compared to dry grinding (A) Requires more energy (B) Has less capacity (C) Complicates handling & classification of the product (D) None of these

Description : In case of a revolving mill, wet grinding compared to dry grinding (A) Requires more energy (B) Has less capacity (C) Complicates handling & classification of the product (D) None of these

Last Answer : (D) None of these

Pick out the wrong statement. (A) Alkylation produces a larger iso-paraffin (having higher octane number) from the reaction of an olefin with smaller iso-paraffin (B) Catalytic alkylation processes use HF, AlCl3 & H2SO4 as Catalysts (C) All the alkylation processes use very high temperature (> 1000°C) (D) Gasoline having an octane number of 90 can be produced by alkylation process

Description : Pick out the wrong statement. (A) Alkylation produces a larger iso-paraffin (having higher octane number) from the reaction of an olefin with smaller iso-paraffin (B) Catalytic alkylation processes use HF ... (> 1000°C) (D) Gasoline having an octane number of 90 can be produced by alkylation process

Last Answer : (C) All the alkylation processes use very high temperature (> 1000°C)

Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to Nusselt number in heat transfer and Schmidt number to Prandtl number (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger (D) Hot gases at moderate pressure are usually in the shell side of shell and tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Description : Pick out the wrong statement. (A) In drying a solid containing moisture above the critical moisture content the number of degrees of freedom is 2 (B) Sherwood number in mass transfer corresponds to ... tube heat exchangers. At higher pressure, however, it is customary to put gas in the tube side

Last Answer : (C) Forced convection is relatively more effective in increasing the rate of mass transfer, if Schmidt number is larger

Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation (B) Cavitation may be caused due to boiling of liquid by decreasing the pressure resulting in formation & collapse of vapor cavities (C) Cavitation begins at higher static pressure and lower velocity in larger diameter pipelines resulting in audible noise(D) Large scale cavitation cannot damage pipeline, restrict fluid flow anddamage steam turbine blades

Description : Pick out the wrong statement about cavitation. (A) Sudden reduction of pressure in a fluid flow system caused by flow separation, vortex formation or abrupt closing of valve leads to cavitation ... (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

Last Answer : (D) Large scale cavitation cannot damage pipeline, restrict fluid flow and damage steam turbine blades

For grinding of softer materials, the grinding wheel should have __________ grain size. (A) Finer (B) Coarser (C) Medium (D) Any type of

Description : For grinding of softer materials, the grinding wheel should have __________ grain size. (A) Finer (B) Coarser (C) Medium (D) Any type of

Last Answer : (B) Coarser

In the manufacture of H3 PO4 (ortho); strong H2 SO4 leaching wet process as compared to electric furnace process (A) Uses lower grade phosphate rock (B) Requires lower capital investment in the plant(C) Produces lower purity acid(D) Is very costly

Description : In the manufacture of H3 PO4 (ortho); strong H2 SO4 leaching wet process as compared to electric furnace process (A) Uses lower grade phosphate rock (B) Requires lower capital investment in the plant (C) Produces lower purity acid (D) Is very costly

Last Answer : (C) Produces lower purity acid

Lurgi gasifier (high pressure gasifier) as compared to Kopper Totzek gasifier (atmospheric pressure gasifier) produces (A) Higher amount of methane (B) Lower amount of hydrogen (C) Both (A) and (B) (D) Higher amount of both methane and hydrogen

Description : Lurgi gasifier (high pressure gasifier) as compared to Kopper Totzek gasifier (atmospheric pressure gasifier) produces (A) Higher amount of methane (B) Lower amount of hydrogen (C) Both (A) and (B) (D) Higher amount of both methane and hydrogen

Last Answer : (C) Both (A) and (B)

Given the following statements : S1 : SLR uses follow information to guide reductions. In case of LR and LALR parsers, the look-aheads are associated with the items and they make use of the left context available to the parser. S2 : LR grammar is a larger sub-class of context free grammar as compared to that SLR and LALR grammars. Which of the following is true ? (A) S1 is not correct and S2 is not correct. (B) S1 is not correct and S2 is correct. (C) S1 is correct and S2 is not correct. (D) S1 is correct and S2 is correct.

Description : Given the following statements : S1 : SLR uses follow information to guide reductions. In case of LR and LALR parsers, the look-aheads are associated with the items and they make use of the left context available to ... (C) S1 is correct and S2 is not correct. (D) S1 is correct and S2 is correct.

Last Answer : (D) S1 is correct and S2 is correct.

Larger length & diameter water pipes are made by (A) Electrical resistance welding (B) Die casting (C) Semi-centrifugal casting (D) Continuous casting

Description : Larger length & diameter water pipes are made by (A) Electrical resistance welding (B) Die casting (C) Semi-centrifugal casting (D) Continuous casting

Last Answer : options A

Larger length & diameter water pipes are made by (A) Electrical resistance welding (B) Die casting (C) Semi-centrifugal casting (D) Continuous casting

Description : Larger length & diameter water pipes are made by (A) Electrical resistance welding (B) Die casting (C) Semi-centrifugal casting (D) Continuous casting

Last Answer : Option C

In the X-ray radiography technique, the tube voltage for thicker plates as compared to thin plates, should be (A) Higher, as it gives higher wavelength (B) Lower, as it gives higher wavelength (C) Higher, as it gives shorter wavelength (D) Lower, as it gives shorter wavelength

Description : In the X-ray radiography technique, the tube voltage for thicker plates as compared to thin plates, should be (A) Higher, as it gives higher wavelength (B) Lower, as it gives higher wavelength (C) Higher, as it gives shorter wavelength (D) Lower, as it gives shorter wavelength

Last Answer : (C) Higher, as it gives shorter wavelength

The operating speed of a ball mill should be __________ the critical speed. (A) Less than (B) Much more than (C) At least equal to (D) Slightly more than

Description : The operating speed of a ball mill should be __________ the critical speed. (A) Less than (B) Much more than (C) At least equal to (D) Slightly more than

Last Answer : (A) Less than

A concave mirror produces a real, inverted image of the same size of the object. Then, the object is at a distance (a) Less than f from the mirror (b) Equal to f from the mirror (c) Equal to 2f from the mirror (d) Larger than 2F from the mirror where f is the focal length of the mirror

Description : A concave mirror produces a real, inverted image of the same size of the object. Then, the object is at a distance (a) Less than f from the mirror (b) Equal to f from the mirror (c) Equal to 2f from the mirror (d) Larger than 2F from the mirror where f is the focal length of the mirror

Last Answer : Ans:(c)

Rapid gravity filters (A) Were developed by G.W. Fuller (B) Make use of coarser sand with effective size as 0.5 mm (C) Yield as high as 30 times the yield of slow sand filters (D) All the above

Description : Rapid gravity filters  (A) Were developed by G.W. Fuller  (B) Make use of coarser sand with effective size as 0.5 mm  (C) Yield as high as 30 times the yield of slow sand filters  (D) All the above 

Last Answer : (D) All the above 

The admixture of coarser particles like sand or silt to clay causes (A) Decrease in liquid limit and increase in plasticity index (B) Decrease in liquid limit and no change in plasticity index (C) Decrease in both liquid limit and plasticity index (D) Increase in both liquid limit and plasticity index

Description : The admixture of coarser particles like sand or silt to clay causes (A) Decrease in liquid limit and increase in plasticity index (B) Decrease in liquid limit and no change in plasticity index ... in both liquid limit and plasticity index (D) Increase in both liquid limit and plasticity index

Last Answer : Answer: Option C

A thermal nuclear reactor compared to a fast breeder reactor (A) Uses slower neutrons for fission (B) Uses faster neutrons for fission (C) Gives higher power density (D) Requires less fuel to run at the same power level

Description : A thermal nuclear reactor compared to a fast breeder reactor (A) Uses slower neutrons for fission (B) Uses faster neutrons for fission (C) Gives higher power density (D) Requires less fuel to run at the same power level

Last Answer : (A) Uses slower neutrons for fission

A coal having high ratio of volatile matter to fixed carbon as compared to a coal having low ratio of volatile matter to fixed carbon (A) Is less liable to spontaneous combustion on storage (B) Is more difficult to ignite and produces a shorter flame (C) Requires smaller combustion space and less secondary air (D) None of these

Description : A coal having high ratio of volatile matter to fixed carbon as compared to a coal having low ratio of volatile matter to fixed carbon (A) Is less liable to spontaneous combustion on storage (B) ... a shorter flame (C) Requires smaller combustion space and less secondary air (D) None of these

Last Answer : (D) None of these