During a tensile test on a ductile material (A) Nominal stress at fracture is higher than the ultimate stress (B) True stress at fracture is higher than the ultimate stress (C) True stress at fracture is the same as the ultimate stress (D) None of these

During a tensile test on a ductile material
(A) Nominal stress at fracture is higher than the ultimate stress
(B) True stress at fracture is higher than the ultimate stress
(C) True stress at fracture is the same as the ultimate stress
(D) None of these
by

1 Answer

Answer :

(B) True stress at fracture is higher than the ultimate stress
by

Related questions

Which of the following is prone to cup and cone fracture? (A) Cast iron (B) Soft brass (C) Round specimen of ductile metal (D) Flat tensile specimen of ductile metal

Description : Which of the following is prone to cup and cone fracture? (A) Cast iron (B) Soft brass (C) Round specimen of ductile metal (D) Flat tensile specimen of ductile metal

Last Answer : Option C

A member which is subjected to reversible tensile or compressive stress may fail at a stress lower than the ultimate stress of the material. This property of metal, is called (A) Plasticity of the metal (B) Elasticity of the metal (C) Fatigue of the metal (D) Workability of the metal

Description : A member which is subjected to reversible tensile or compressive stress may fail at a stress lower  than the ultimate stress of the material. This property of metal, is called  (A) Plasticity of the ... ) Elasticity of the metal  (C) Fatigue of the metal  (D) Workability of the metal

Last Answer : (C) Fatigue of the metal

__________ test is the appropriate test to determine whether a material is ductile or brittle. (A) Impact (B) Cupping (C) Hardness (D) Tensile

Description : __________ test is the appropriate test to determine whether a material is ductile or brittle. (A) Impact (B) Cupping (C) Hardness (D) Tensile

Last Answer : (A) Impact

Theories of elastic failure while dealing with ductile materials consider the failure criterion as (a) Ultimate stress (b) Yield stress (c) Both ultimate and yield stress (d) None

Description : Theories of elastic failure while dealing with ductile materials consider the failure criterion as (a) Ultimate stress (b) Yield stress (c) Both ultimate and yield stress (d) None

Last Answer : (b) Yield stress

In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Description : In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Last Answer : (a)Firstly Ultimate >yield > elastic limit

A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Description : A power transmitting ductile material shaft under P, T and M will fail under (a) Tensile considerations only (b) Compressive considerations only (c) Shear considerations only (d) None

Last Answer : (c) Shear considerations only

List at least two factors that promote transition from ductile to brittle fracture.

Description : List at least two factors that promote transition from ductile to brittle fracture.

Last Answer : Manner of loading, and the rate of loading promote transition from ductile to brittle frac¬ture. A machine member may have ductile failure under static loading but may fail in brittle fashion when the ... testing speed but if load is applied at a high velocity then failure may be brittle.

Fibrous fracture is normally encountered in the __________ materials. (A) Hard (B) Elastic (C) Ductile

Description : Fibrous fracture is normally encountered in the __________ materials. (A) Hard (B) Elastic (C) Ductile

Last Answer : Option C

The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic

Description : The materials which fracture even at small strains are termed as brittle, while those materials which exhibit an appreciable deformation before failure are termed as (A) Rigid (B) Tough (C) Ductile (D) Plastic

Last Answer : Option C

List At Least Two Factors That Promote The Transition From Ductile To Brittle Fracture?

Description : List At Least Two Factors That Promote The Transition From Ductile To Brittle Fracture?

Last Answer : The manner of loading and the rate of loading promote the transition from ductile to brittle fracture. A machine member may have ductile failure under static loading but may fail in brittle fashion when the ... testing speed, but if the load is applied at a high velocity then failure may be brittle.

Distinguish Between Brittle Fracture And Ductile Fracture?

Description : Distinguish Between Brittle Fracture And Ductile Fracture?

Last Answer : In brittle fracture, crack growth is up to a small depth of the material. In ductile fracture large amount of plastic deformation is present to a higher depth.

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

Factor of safety is a. Tensile stress / Permissible stress b. Compressive stress / Ultimate stress c. Ultimate stress / Permissible stress d. Ultimate stress / Shear stress

Description : Factor of safety is a. Tensile stress / Permissible stress b. Compressive stress / Ultimate stress c. Ultimate stress / Permissible stress d. Ultimate stress / Shear stress

Last Answer : c. Ultimate stress / Permissible stress

The Mohr's straight theory is based on the following fact: (A) Material fails essentially by shear (B) Ultimate strength of the material is determined by the stress in the plane of slip (C) Failure criterion is independent of the intermediate principal stress (D) All the above

Description : The Mohr's straight theory is based on the following fact: (A) Material fails essentially by shear (B) Ultimate strength of the material is determined by the stress in the plane of slip (C) Failure criterion is independent of the intermediate principal stress (D) All the above

Last Answer : Answer: Option D

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Description : In which of the following case stress concentration factor is ignored? a) Ductile material under static load b) Ductile material under fluctuating load c) Brittle material under static load

Last Answer : a) Ductile material under static load

A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None

Description : A ductile material may not meet a failure if it has been tested for the theories of failure (a) Firstly Maximum Shear Stress Theory (b) Secondly Maximum Shear Strain Energy Theory (c) Both (a) & (b) (d) None

Last Answer : (c) Both (a) & (b)

Which stress strain curve is more steep (a) For a ductile material (b) For a brittle material (c) For a pure metal (d) None

Description : Which stress strain curve is more steep (a) For a ductile material (b) For a brittle material (c) For a pure metal (d) None

Last Answer : b) For a brittle material

The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm2

Description : The ultimate tensile strength of structural mild steel is about (A) 160 N/mm² (B) 260 N/mm² (C) 420 N/mm² (D) 520 N/mm

Last Answer : Answer: Option C

Wrought iron is not (A) Ductile & resistant to corrosion/rusting (B) Weldable easily (C) Having uniform strength in all directions (D) Having maximum tensile strength along the lines of slag distribution

Description : Wrought iron is not (A) Ductile & resistant to corrosion/rusting (B) Weldable easily (C) Having uniform strength in all directions (D) Having maximum tensile strength along the lines of slag distribution

Last Answer : Option C

Hooke’s law is applicable within (a)Elastic limit (b)Plastic limit (c)Fracture point (d) Ultimate strength

Description : Hooke’s law is applicable within (a)Elastic limit (b)Plastic limit (c)Fracture point (d) Ultimate strength

Last Answer : (a)Elastic limit

For a loose sand sample and a dense sand sample consolidated to the same effective stress (A) Ultimate strength is same and also peak strength is same (B) Ultimate strength is different but peak strength is same (C) Ultimate strength is same but peak strength of dense sand is greater than that of loose sand (D) Ultimate strength is same but peak

Description : For a loose sand sample and a dense sand sample consolidated to the same effective stress (A) Ultimate strength is same and also peak strength is same (B) Ultimate strength is different but peak strength ... of dense sand is greater than that of loose sand (D) Ultimate strength is same but peak

Last Answer : (C) Ultimate strength is same but peak strength of dense sand is greater than that of loose sand

In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2 , nominal reinforcement is provided at a pitch of (A) One-half lever arm of the section (B) One-third lever arm of the section (C) Lever arm of the section (D) One and half lever arm of the section

Description : In the zone of R.C.C. beam where shear stress is less than 5 kg/cm2 , nominal reinforcement is provided at a pitch of (A) One-half lever arm of the section (B) One-third lever arm of the section (C) Lever arm of the section (D) One and half lever arm of the section

Last Answer : Answer: Option C

When the nominal shear stress is less than permissible shear stress in concrete then [ A ] Provide minimum shear reinforcement [ B ] No shear reinforcement is necessary [ C ] Provide design shear reinforcement [ D ] None of the above

Description : When the nominal shear stress is less than permissible shear stress in concrete then [ A ] Provide minimum shear reinforcement [ B ] No shear reinforcement is necessary [ C ] Provide design shear reinforcement [ D ] None of the above

Last Answer : [ A ] Provide minimum shear reinforcement

Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Description : Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Last Answer : E. Elastic limit was exceeded

When mild steel is subjected to a tensile load, its fracture will conform to (a) Star shape (b) Granular shape (c) Cup and cone shape (d) Fibrous shape

Description : When mild steel is subjected to a tensile load, its fracture will conform to (a) Star shape (b) Granular shape (c) Cup and cone shape (d) Fibrous shape

Last Answer : (c) Cup and cone shape

In the Haig-Soderberg diagram, the test data for ductile material falls near the ______________ a) Soderberg line b) Goodman Line c) Gerber line d) Haig line

Description : In the Haig-Soderberg diagram, the test data for ductile material falls near the ______________ a) Soderberg line b) Goodman Line c) Gerber line d) Haig line

Last Answer : c) Gerber line

In a combined footing if shear stress does not exceed 5 kg/cm2 , the nominal stirrups provided are (A) 6 legged (B) 8 legged (C) 10 legged (D) 12 legged

Description : In a combined footing if shear stress does not exceed 5 kg/cm2 , the nominal stirrups provided are (A) 6 legged (B) 8 legged (C) 10 legged (D) 12 legged

Last Answer : Answer: Option B

If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Description : If the maximum shear stress at the end of a simply supported R.C.C. beam of 16 m effective span is 10 kg/cm2 , the length of the beam having nominal reinforcement, is (A) 8 cm (B) 6 m (C) 8 m (D) 10 m

Last Answer : Answer: Option C

In a combined footing if shear stress exceeds 5 kg/cm2 , the nominal stirrups provided are: (A) 6 legged (B) 8 legged (C) 10 legged (D) 12 legged

Description : In a combined footing if shear stress exceeds 5 kg/cm2 , the nominal stirrups provided are: (A) 6 legged (B) 8 legged (C) 10 legged (D) 12 legged

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) A ductile material has large plastic zone (B) A brittle material has no plastic zone (C) A rigid material has no plastic zone (D) All the above

Description : Pick up the correct statement from the following: (A) A ductile material has large plastic zone (B) A brittle material has no plastic zone (C) A rigid material has no plastic zone (D) All the above

Last Answer : All the above

The material in which large deformation is possible before absolute failure by rupture takes place, is known as (a) Ductile (b) Plastic (c) Brittle (d) Elastic

Description : The material in which large deformation is possible before absolute failure by rupture takes place, is known as (a) Ductile (b) Plastic (c) Brittle (d) Elastic

Last Answer : Ductile

The ratio of the length and diameter of a simply supported uniform circular beam which experiences maximum bending stress equal to tensile stress due to same load at its mid span, is (A) 1/8 (B) 1/4 (C) 1/2 (D) 1/3

Description : The ratio of the length and diameter of a simply supported uniform circular beam which  experiences maximum bending stress equal to tensile stress due to same load at its mid span, is  (A) 1/8  (B) 1/4  (C) 1/2  (D) 1/3 

Last Answer : (C) 1/2 

The ratio of the length and depth of a simply supported rectangular beam which experiences maximum bending stress equal to tensile stress, due to same load at its mid span, is (A) 1/2 (B) 2/3 (C) 1/4 (D) 1/3

Description : The ratio of the length and depth of a simply supported rectangular beam which experiences  maximum bending stress equal to tensile stress, due to same load at its mid span, is  (A) 1/2  (B) 2/3  (C) 1/4  (D) 1/3

Last Answer : (B) 2/3 

Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress – strain curve for steel in compression is the same as in tension [ C ] The strain at different points in the section will be same [ D ] Plane section remain plane even after bending

Description : Select the incorrect statement from the following In eccentrically loaded columns, [ A ] The tensile strength of concrete is ignored [ B ] Design stress - strain curve for steel in compression is the ... different points in the section will be same [ D ] Plane section remain plane even after bending

Last Answer : [ C ] The strain at different points in the section will be same

In cement concrete pavements, tensile stress is due to: (A) Bending or deflection under wheel loads (B) Difference in temperature of the top and bottom of pavement (C) Contraction of slab during falling temperature (D) All the above

Description : In cement concrete pavements, tensile stress is due to: (A) Bending or deflection under wheel loads (B) Difference in temperature of the top and bottom of pavement (C) Contraction of slab during falling temperature (D) All the above

Last Answer : Answer: Option D

Ceramic compounds as compared to metallic compounds (A) Crystallise faster (B) Resist greater tensile stress at room temperature (C) Have higher melting temperature (D) Are better conductor of electricity at higher temperature

Description : Ceramic compounds as compared to metallic compounds (A) Crystallise faster (B) Resist greater tensile stress at room temperature (C) Have higher melting temperature (D) Are better conductor of electricity at higher temperature

Last Answer : Option C

The stress at which extension of the material takes place more rapidly as compared to the increase in load is termed as the __________ point of the material. (A) Elastic (B) Ultimate (C) Yielding (D) Breaking

Description : The stress at which extension of the material takes place more rapidly as compared to the increase in load is termed as the __________ point of the material. (A) Elastic (B) Ultimate (C) Yielding (D) Breaking

Last Answer : (C) Yielding

Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False

Description : Stress Concentration Factor is the ratio of nominal stress obtained by elementary equations for minimum cross- section and highest value of actual stress near discontinuity. a) True b) False

Last Answer : b) False

Examine the following statements: (i) Factor of safety for steel should be based on its yield stress, (ii) Factor of safety for steel should be based on its ultimate stress, (iii) Factor of safety for concrete should be based on its yield stress, (iv) Factor of safety for concrete should be based on its ultimate stress. The correct statements are (A) (i) and (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv

Description : Examine the following statements: (i) Factor of safety for steel should be based on its yield stress, (ii) Factor of safety for steel should be based on its ultimate stress, (iii) Factor of safety for concrete should be based on ... (iii) (B) (i) and (iv) (C) (ii) and (iii) (D) (ii) and (iv

Last Answer : Answer: Option B

Which of the following stresses is used for identifying the quality of structural steel? (A) Ultimate stress (B) Yield stress (C) Proof stress (D) None of the abov

Description : Which of the following stresses is used for identifying the quality of structural steel? (A) Ultimate stress (B) Yield stress (C) Proof stress (D) None of the above

Last Answer : Answer: Option B

Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild steel bar in tension from initial zero strain to failure is (a) 4, 1, 2, 3 and 5 (b) 1, 4, 3, 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Description : Consider the following salient points in a stress-strain curve of a mild steel bar: 1. Yield point 2. Braking point 3. Yield plateau 4 . Proportionality limit 5. Ultimate point The correct sequence in which they occur while testing the mild ... , 5 and 2 (c) 4, 1, 3, 5 and 2 (d) 1, 4, 2, 3 and 5

Last Answer : (c) 4, 1, 3, 5 and 2

The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2

Description : The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2

Last Answer : [ B ] 1.92 N/mm2

The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2

Description : The ultimate average anchorage bond stress for plain bars in tension is _______ if the grade of concrete is M20 [ A ] 1.60 N/mm2 [ B ] 1.92 N/mm2 [ C ] 2.24 N/mm2 [ D ] 2.40 N/mm2

Last Answer : [ B ] 1.92 N/mm2

Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Description : Cast iron has (A) Very high tensile strength (B) High ductility (C) High malleability (D) Elastic limit close to ultimate breaking strength

Last Answer : (D) Elastic limit close to ultimate breaking strength

When the steel is subjected to normalising, its __________ decreases. (A) Yield point (B) Ductility (C) Ultimate tensile strength (UTS)

Description : When the steel is subjected to normalising, its __________ decreases. (A) Yield point (B) Ductility (C) Ultimate tensile strength (UTS)

Last Answer : (B) Ductility

Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Description : Cast iron has (A) High ductility (B) High malleability (C) Very high tensile strength (D) Its elastic limit very close to ultimate breaking strength

Last Answer : (D) Its elastic limit very close to ultimate breaking strength