To ascertain the maximum permissible eccentricity of loads on circular columns, the rule generally followed, is (A) Middle half rule of columns (B) Middle third rule of columns (C) Middle fourth rule of columns (D) None of these

To ascertain the maximum permissible eccentricity of loads on circular columns, the rule generally
followed, is
(A) Middle half rule of columns
(B) Middle third rule of columns
(C) Middle fourth rule of columns
(D) None of these
by

1 Answer

Answer :

(C) Middle fourth rule of columns
by

Related questions

The maximum permissible eccentricity for no tension at the base of a gravity dam is (A) B/2 (B) B/3 (C) B/4 (D) B/6

Description : The maximum permissible eccentricity for no tension at the base of a gravity dam is (A) B/2 (B) B/3 (C) B/4 (D) B/6

Last Answer : Answer: Option D

The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is (A) One-half of the radius (B) One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (C) One-quarter of the radius (D) One-fifth of the radius

Last Answer : (C) One-quarter of the radius

According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is (A) Half of the width of the slab (B) Two-third of the width of the slab (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Description : According to I.S. : 456, slabs which span in two directions with corners held down, are assumed to be divided in each direction into middle strips and edge strips such that the width of the middle strip, is ... (C) Three-fourth of the width of the slab (D) Four-fifth of the width of the slab

Last Answer : Answer: Option C

The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom

Description : The thickness of base slab of a retaining wall generally provided, is (A) One half of the width of the stem at the bottom (B) One-third of the width of the stem at the bottom (C) One fourth of the width of the steam at the bottom (D) Width of the stem at the bottom

Last Answer : Answer: Option D

The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, is (a) One-half of the radius (b) One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius

Description : The region of the cross-section of a column in which compressive load may be applied without producing any tensile stress, is known as the core of the cross-section. In circular columns the radius of the core, ... One-third of the radius (c) One-quarter of the radius (d) One-fifth of the radius

Last Answer : (c) One-quarter of the radius

In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force

Description : In a combined footing for two columns carrying unequal loads, the maximum hogging bending moment occurs at (A) Less loaded column (B) More loaded column (C) A point of the maximum shear force (D) A point of zero shear force

Last Answer : Answer: Option D

Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of (A) 0.1 L from the outer edge of column (B) 0.1 L from the centre edge of column (C) Half the distance of projection (D) One-fourth the distance of projection

Description : Top bars are extended to the projecting parts of the combined footing of two columns Ldistance apart for a distance of (A) 0.1 L from the outer edge of column (B) 0.1 L from the centre edge of column (C) Half the distance of projection (D) One-fourth the distance of projection

Last Answer : Answer: Option B

The power transmitted through the pipe is maximum when the head lost due to friction is equal to (A) One-fourth of the total supply head (B) One-third of the total supply head (C) One-half of the total supply head (D) Two-third of the total supply head

Description : The power transmitted through the pipe is maximum when the head lost due to friction is equal to (A) One-fourth of the total supply head (B) One-third of the total supply head (C) One-half of the total supply head (D) Two-third of the total supply head

Last Answer : Answer: Option B

The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm for an eccentric load 100 t for non-development of tension, is (A) 2.75 cm (B) 3.00 cm (C) 3.50 cm (D) 4.25 cm

Description : The eccentricity (e) of a hollow circular column, external diameter 25 cm, internal diameter 15 cm  for an eccentric load 100 t for non-development of tension, is  (A) 2.75 cm  (B) 3.00 cm  (C) 3.50 cm  (D) 4.25 cm

Last Answer : (D) 4.25 cm

A uniformly-loaded D.C. distributor is fed at both ends with equal voltages. As compared to a similar distributor fed at one end only, the drop at the middle point is (a) one-fourth (b) one-third (c) one-half (d) twice (e) none of the above

Description : A uniformly-loaded D.C. distributor is fed at both ends with equal voltages. As compared to a similar distributor fed at one end only, the drop at the middle point is (a) one-fourth (b) one-third (c) one-half (d) twice (e) none of the above

Last Answer : (a) one-fourth

Pick up the correct statement from the following: (A) Construction joints in columns are provided a few cm below the junction of beam (B) Construction joints in columns are provided at the bottom hunching (C) Construction joints in beams and slabs are provided within middle third (D) All the above

Description : Pick up the correct statement from the following: (A) Construction joints in columns are provided a few cm below the junction of beam (B) Construction joints in columns are provided at the bottom ... (C) Construction joints in beams and slabs are provided within middle third (D) All the above

Last Answer : Answer: Option D

The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0

Description : The length of a column, having a uniform circular cross-section of 7.5 cm diameter and whose ends are hinged, is 5 m. If the value of E for the material is 2100 tonnes/cm2 , the permissible maximum crippling load will be (A) 1.288 tonnes (B) 12.88 (C) 128.8 tonnes (D) 288.0

Last Answer : (B) 12.88

According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Description : According to IS:456, the diameter of the helices in circular a column shall be at least [ A ] The diameter of longitudinal steel [ B ] One-half the diameter of longitudinal steel [ C ] One-fourth the diameter of longitudinal steel [ D ] Three-fourth the diameter of longitudinal steel

Last Answer : [ C ] One-fourth the diameter of longitudinal steel

Columns of given length, cross-section and material have different values of buckling loads for different end conditions. The strongest column is one whose (A) One end is fixed and other end is hinged (B) Both ends are hinged or pin jointed (C) One end is fixed and the other end entirely free (D) Both the ends are fixed

Description : Columns of given length, cross-section and material have different values of buckling loads for different end conditions. The strongest column is one whose (A) One end is fixed and other end is hinged (B) Both ... (C) One end is fixed and the other end entirely free (D) Both the ends are fixed

Last Answer : (D) Both the ends are fixed

If the length of a combined footing for two columns l metres apart is L and the projection on the left side of the exterior column is x, then the projection y on the right side of the exterior column, in order to have a uniformly distributed load, is (where is the distance of centre of gravity of column loads). (A) y = L - (l - ) (B) y = L/2 + (l - ) (C) y = L/2 - (l + ) (D) y = L/2 - (l - )

Description : If the length of a combined footing for two columns l metres apart is L and the projection on the left side of the exterior column is x, then the projection y on the right side of the exterior column, in order to have a uniformly distributed ... l - ) (C) y = L/2 - (l + ) (D) y = L/2 - (l - )

Last Answer : Answer: Option D

Grillage foundation (A) Is used to transfer heavy structural loads from steel columns to a soil having low bearing capacity (B) Is light and economical (C) Does not require deep cutting as the required base area with required pressure intensity is obtained at a shallow depth (D) All the above

Description : Grillage foundation (A) Is used to transfer heavy structural loads from steel columns to a soil having low bearing capacity (B) Is light and economical (C) Does not require deep cutting as the required base area with required pressure intensity is obtained at a shallow depth (D) All the above

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The roof slabs of multi-storeyed buildings are constructed monolithically to carry the various floor loads (B) The beams of multi-storeyed buildings rest on girders and are the main load transferring members to the columns (C) The slab is spanned across the secondary beams provided between the main beams (D) All of these

Description : Pick up the correct statement from the following: (A) The roof slabs of multi-storeyed buildings are constructed monolithically to carry the various floor loads (B) The beams of multi-storeyed ... slab is spanned across the secondary beams provided between the main beams (D) All of these

Last Answer : Answer: Option D

The type of footing which is used to transmit heavy loads through steel columns is (A) Raft foundation (B) Grillage foundation (C) Well foundation (D) Isolated footing

Description : The type of footing which is used to transmit heavy loads through steel columns is (A) Raft foundation (B) Grillage foundation (C) Well foundation (D) Isolated footing

Last Answer : Option B

The columns of multi-storeyed buildings are designed to withstand the forces due to (A) Dead loads (B) Live loads (C) Wind loads (D) All of these

Description : The columns of multi-storeyed buildings are designed to withstand the forces due to (A) Dead loads (B) Live loads (C) Wind loads (D) All of these

Last Answer : Option D

Columns in which lateral loads have to be resisted in addition to vertical loads by the strength of the columns themselves are considered as [ A ] Braced columns [ B ] Un braced columns [ C ] Slender columns [ D ] None of the above

Description : Columns in which lateral loads have to be resisted in addition to vertical loads by the strength of the columns themselves are considered as [ A ] Braced columns [ B ] Un braced columns [ C ] Slender columns [ D ] None of the above

Last Answer : [ B ] Un braced columns

A pre-stressed rectangular beam which carries two concentrated loads W at L/3 from either end, is provided with a bent tendon with tension P such that central one-third portion of the tendon remains parallel to the longitudinal axis, the maximum dip h is (A) WL/P (B) WL/2P (C) WL/3P (D) WL/4P

Description : A pre-stressed rectangular beam which carries two concentrated loads W at L/3 from either end, is provided with a bent tendon with tension P such that central one-third portion of the tendon remains parallel to the longitudinal axis, the maximum dip h is (A) WL/P (B) WL/2P (C) WL/3P (D) WL/4P

Last Answer : Answer: Option C

Which one of the following activities is not correct as applicable to brick corbels? (A) The maximum projection of the corbel should not be more than the thickness of the wall (B) The maximum projection of each corbel course should be limited to a quarter brick at a time (C) The discontinuous corbels are used to carry heavy concentrated loads (D) Stretcher bond is generally used for the construction of brick corbel

Description : Which one of the following activities is not correct as applicable to brick corbels? (A) The maximum projection of the corbel should not be more than the thickness of the wall (B) The ... to carry heavy concentrated loads (D) Stretcher bond is generally used for the construction of brick corbel

Last Answer : Answer: Option D

You are asked to design sewer pipes of diameters 0.4 m to 0.9 m at maximum flow, you will assume the sewer flow running at A. Full depth B. Half full C. Two third full D. Three fourth full

Description : You are asked to design sewer pipes of diameters 0.4 m to 0.9 m at maximum flow, you will assume the sewer flow running at A. Full depth B. Half full C. Two third full D. Three fourth full

Last Answer : ANS: B

Under section 65 of IPC sentence of imprisonment for non-payment of fine shall be limited to (a) One-third of the maximum term of imprisonment fixed for the offence (b) One-fourth of the maximum term of imprisonment fixed for the offence (c) One-half of the maximum term of imprisonment fixed for the offence (d) Equal to the maximum term of imprisonment fixed for the offence.

Description : Under section 65 of IPC sentence of imprisonment for non-payment of fine shall be  limited to (a) One-third of the maximum term of imprisonment fixed for the offence (b) One-fourth of the ... imprisonment fixed for the offence (d) Equal to the maximum term of imprisonment fixed for the offence.

Last Answer : (b) One-fourth of the maximum term of imprisonment fixed for the offence

Center of gravity of a solid cone lies on the axis at the height (A) One-fourth of the total height above base (B) One-third of the total height above base (C) One-half of the total height above base (D) Three-eighth of the total height above the base

Description : Center of gravity of a solid cone lies on the axis at the height (A) One-fourth of the total height above base (B) One-third of the total height above base (C) One-half of the total height above base (D) Three-eighth of the total height above the base

Last Answer : (A) One-fourth of the total height above base

Center of gravity of a thin hollow cone lies on the axis at a height of (A) One-fourth of the total height above base (B) One-third of the total height above base (C) One-half of the total height above base (D) Three-eighth of the total height above the base

Description : Center of gravity of a thin hollow cone lies on the axis at a height of (A) One-fourth of the total height above base (B) One-third of the total height above base (C) One-half of the total height above base (D) Three-eighth of the total height above the base

Last Answer : (B) One-third of the total height above base

In a short cylindrical external mouthpiece, the vena contracta occurs at a distance __________ the diameter of the orifice from the outlet of orifice. (A) Equal to (B) One-fourth (C) One-third (D) One-half

Description : In a short cylindrical external mouthpiece, the vena contracta occurs at a distance __________ the diameter of the orifice from the outlet of orifice. (A) Equal to (B) One-fourth (C) One-third (D) One-half

Last Answer : Answer: Option B

The loose pockets in soil mass can be bridged safely by providing a raft foundation provided the soft area is smaller than (A) The column spacing (B) One-third the column spacing (C) Half the column spacing (D) Three-fourth the column spacing

Description : The loose pockets in soil mass can be bridged safely by providing a raft foundation provided the soft area is smaller than (A) The column spacing (B) One-third the column spacing (C) Half the column spacing (D) Three-fourth the column spacing

Last Answer : Answer: Option B

The breadth of rib in a T-beam should at least be equal to __________the depth of rib (a) One –half (b) One –third (c) One-fourth (d) One –sixth

Description : The breadth of rib in a T-beam should at least be equal to __________the depth of rib (a) One –half (b) One –third (c) One-fourth (d) One –sixth

Last Answer : (b) One –third

The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm

Description : The diameter of transverse reinforcement of columns should be equal to one-fourth of the diameter of the main steel rods but not less than (A) 4 mm (B) 5 mm (C) 6 mm (D) 7 mm

Last Answer : Answer: Option D

In a broad-crested weir, the discharge is maximum if the head of water on the downstream side of weir is __________ the head of water on the upstream side of weir. (A) Equal to (B) One-third (C) Two-third (D) Three-fourth

Description : In a broad-crested weir, the discharge is maximum if the head of water on the downstream side of weir is __________ the head of water on the upstream side of weir. (A) Equal to (B) One-third (C) Two-third (D) Three-fourth

Last Answer : Answer: Option C

The minimum number of main steel bars provided in R.C.C. (A) Rectangular columns is 4 (B) Circular columns is 6 (C) Octagonal columns is 8 (D) All the above

Description : The minimum number of main steel bars provided in R.C.C. (A) Rectangular columns is 4 (B) Circular columns is 6 (C) Octagonal columns is 8 (D) All the above

Last Answer : Answer: Option D

Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not exceed four [ C ] The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Description : Select the incorrect statement from the following [ A ] Reinforcing bars in a column should not be less than 12 mm in diameter [ B ] The number of longitudinal bars in a circular column should not ... The minimum percentage of longitudinal steel in columns should be 0.8% [ D ] None of the above

Last Answer : [ B ] The number of longitudinal bars in a circular column should not exceed four

The Minimum pitch of the helical reinforcement in circular columns should be [ A ] 25 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm

Description : The Minimum pitch of the helical reinforcement in circular columns should be [ A ] 25 mm [ B ] 40 mm [ C ] 50 mm [ D ] 60 mm

Last Answer : [ A ] 25 mm

The Pitch of helixes in circular columns shall not exceed [ A ] 25 mm [ B ] 50 mm [ C ] 60 mm [ D ] 75 mm

Description : The Pitch of helixes in circular columns shall not exceed [ A ] 25 mm [ B ] 50 mm [ C ] 60 mm [ D ] 75 mm

Last Answer : [ D ] 75 mm

Pick out the correct statement. (A) For identical gas flow rates, less pressure drop occurs through a plate tower than through a packed tower (B) Plate column can handle greater liquid loads without flooding than packed column, but the liquid hold up is more in the case of plate column (C) For the same duty, plate columns weigh less than packed columns (D) All (A), (B) and (C)

Description : Pick out the correct statement. (A) For identical gas flow rates, less pressure drop occurs through a plate tower than through a packed tower (B) Plate column can handle greater liquid loads without flooding than packed ... duty, plate columns weigh less than packed columns (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Columns of given length, cross-section and material have different values of buckling loads for different end conditions. The strongest column is one whose (a) One end is fixed and other end is hinged (b) Both ends are hinged or pin jointed (c) One end is fixed and the other end entirely free (d) Both the ends are fixed

Description : Columns of given length, cross-section and material have different values of buckling loads for different end conditions. The strongest column is one whose (a) One end is fixed and other end is hinged (b) ... (c) One end is fixed and the other end entirely free (d) Both the ends are fixed

Last Answer : (d) Both the ends are fixed

The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Description : The Maximum diameter steel in slabs should not exceed --------- the total thickness of the slab [ A ] One-half [ B ] One-fourth [ C ] One-eighth [ D ] One-sixteenth

Last Answer : [ C ] One-eighth

The Maximum shear stress in Slabs should not exceed -------- the maximum values allowed for beams. [ A ] Half Of [ B ] One-Fourth Of [ C ] Twice [ D ] Those Given In

Description : The Maximum shear stress in Slabs should not exceed -------- the maximum values allowed for beams. [ A ] Half Of [ B ] One-Fourth Of [ C ] Twice [ D ] Those Given In

Last Answer : [ A ] Half Of

A circular gravity aqueduct is not generally preferred to because of (A) Its maximum hydraulic mean depth (B) Maximum area per unit of wetted perimeter (C) Minimum cost of construction (D) Its proper support on the ground

Description : A circular gravity aqueduct is not generally preferred to because of (A) Its maximum hydraulic mean depth (B) Maximum area per unit of wetted perimeter (C) Minimum cost of construction (D) Its proper support on the ground

Last Answer : (D) Its proper support on the ground

Pickup the incorrect statement from the following: (A) The invert of pressure conduit is independent of the grade of the hydraulic gradient line (B) The pressure conduits may be taken uphill upto a maximum height of 8.3 m (C) Aqueducts and tunnels sections are generally kept circular (D) None of these

Description : Pickup the incorrect statement from the following:  (A) The invert of pressure conduit is independent of the grade of the hydraulic gradient line  (B) The pressure conduits may be taken uphill ... m  (C) Aqueducts and tunnels sections are generally kept circular  (D) None of these 

Last Answer : (D) None of these 

Sharp crested weirs are generally used (A) For large flows (B) For small flows (C) For streams carrying high sediment loads (D) For rivers carrying floating debris

Description : Sharp crested weirs are generally used (A) For large flows (B) For small flows (C) For streams carrying high sediment loads (D) For rivers carrying floating debris

Last Answer : Answer: Option A

Pick up the correct statement from the following: (A) The sand in the sand pile is well compacted (B) The sand is kept moist at the time of placing and tamping (C) Sand piles are generally used under column loads (D) All of the above

Description : Pick up the correct statement from the following: (A) The sand in the sand pile is well compacted (B) The sand is kept moist at the time of placing and tamping (C) Sand piles are generally used under column loads (D) All of the above

Last Answer : Answer: Option D

Liquefied Petroleum Gas (LPG) in domestic use cylinders is in the liquid form. The density of LPG in liquid form is about __________ of that of water (i.e. 1 gm/c.c). (A) One fourth (B) One third (C) Half (D) One eighth

Description : Liquefied Petroleum Gas (LPG) in domestic use cylinders is in the liquid form. The density of LPG in liquid form is about __________ of that of water (i.e. 1 gm/c.c). (A) One fourth (B) One third (C) Half (D) One eighth

Last Answer : (C) Half

The fraction of earth’s surface covered with water. (a) One-fourth (b) Half (c) Three-fourth (d) Two-third.

Description : The fraction of earth’s surface covered with water. (a) One-fourth (b) Half (c) Three-fourth (d) Two-third.

Last Answer : (c) Three-fourth

Ultimate strength in tension as compared to that in shear for steel is (A) Half (B) One third (C) One and half times (D) One fourth

Description : Ultimate strength in tension as compared to that in shear for steel is (A) Half (B) One third (C) One and half times (D) One fourth

Last Answer : (C) One and half times

The diameter of internal flue tubes of a Lancashire boiler is about _______ that of it’s shell a. One fourth b. One third c. Two fifth d. One half

Description : The diameter of internal flue tubes of a Lancashire boiler is about _______ that of it’s shell a. One fourth b. One third c. Two fifth d. One half

Last Answer : c. Two fifth

The pressure exerted by an ideal gas is __________ of the kinetic energy of all the molecules contained in a unit volume of gas.  A.one-half  B.one-third  C.two-third  D.three-fourth

Description : The pressure exerted by an ideal gas is __________ of the kinetic energy of all the molecules contained in a unit volume of gas.  A.one-half  B.one-third  C.two-third  D.three-fourth

Last Answer : Answer: C