Check valves are installed (A) On the delivery side of the pumping set (B) At the interconnections between polluted water system and a potable water system (C) Both (a) and (b) (D) Neither (a) nor (b)

Check valves are installed
(A) On the delivery side of the pumping set
(B) At the interconnections between polluted water system and a potable water system
(C) Both (a) and (b)
(D) Neither (a) nor (b)
by

1 Answer

Answer :

(C) Both (a) and (b)
by

Related questions

Replenishment of dissolved oxygen in water stream polluted with industrial waste occurs by (A) Natural aeration of water stream (B) Photosynthetic action of algae (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Replenishment of dissolved oxygen in water stream polluted with industrial waste occurs by (A) Natural aeration of water stream (B) Photosynthetic action of algae (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Biological oxidation ponds remove organic matters present in the polluted water by (A) Using the activities of bacteria and other micro organisms (B) Aerobic oxidation (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Biological oxidation ponds remove organic matters present in the polluted water by (A) Using the activities of bacteria and other micro organisms (B) Aerobic oxidation (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Regenerators are installed in (A) Coke ovens (B) Open hearth furnace (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Regenerators are installed in (A) Coke ovens (B) Open hearth furnace (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Prime coking coal is always blended with medium or non- coking coal before carbonisation (A) To check against its excessive swelling during heating, which may exert high pressure and damage coke oven walls (B) Because, it alone produces unreactive coke (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Prime coking coal is always blended with medium or non- coking coal before carbonisation (A) To check against its excessive swelling during heating, which may exert high pressure and damage coke oven walls (B) Because, it alone produces unreactive coke (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

A voltmeter located on a control panel has been operating correctly for six months, suddenly burns out. After removing it, it is found that neither side of the meter has been grounded. When installing the new meter it should be __________. A. grounded to the negative side B. connected to a large resistor between the positive side and the ground C. installed exactly as the old installation D. grounded to the positive side

Description : A voltmeter located on a control panel has been operating correctly for six months, suddenly burns out. After removing it, it is found that neither side of the meter has been grounded. When ... side and the ground C. installed exactly as the old installation D. grounded to the positive side

Last Answer : Answer: C

Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259

Description : Which coaxial connector is a more complex and expensive but do a better job in maintaining the electrical characteristics of the cable through the interconnections? A. N-type connector B. F-type connector C.BNC D. PL-259

Last Answer : A. N-type connector

Research scientists all over the world are taking steps towards building computers with circuits patterned after the complex interconnections existing among the human brain’s nerve cells. What name is given to such type of computers? a) Intelligent computers b) Supercomputers c) Neural network computers d) Smart computers

Description : Research scientists all over the world are taking steps towards building computers with circuits patterned after the complex interconnections existing among the human brain's nerve cells. What name ... ? a) Intelligent computers b) Supercomputers c) Neural network computers d) Smart computers

Last Answer : c) Neural network computers

What are the three most common methods of interconnections?

Description : What are the three most common methods of interconnections?

Last Answer : Conventional printed circuit boards, multilayer printed circuit boards and modular assemblies.

A boy presses a side of a blue pencil to a side of a yellow pencil, holding both pencils vertically. One inch of the pressed side of the blue pencil, measuring from its lower end, is smeared with paint. The yellow pencil is held steady while the boy slides the blue pencil down 1 inch, continueing to press it against the yellow one. He returns the blue pencil to its former position, then again it slides down 1 inch. He continues until he has lowered the blue pencil 5 times and raised it 5 times- 10 moves in all.Supposed that during this time the paint neither dries nor diminishes in quantity. How many inches of each pencil will be sneared with paint after the tenth move? -Riddles

Description : A boy presses a side of a blue pencil to a side of a yellow pencil, holding both pencils vertically. One inch of the pressed side of the blue pencil, measuring from its lower end, is smeared ... in quantity. How many inches of each pencil will be sneared with paint after the tenth move? -Riddles

Last Answer : At the start, 1inch of the yellow pencil gets smeared with wet paint. As the blue pencil is moved downward, a second inch of the blue pencils smears a second inch of the yellow pencil. Each pair ... of moves will smear 5 inches. This together with the initial inch, makes 6 inches for each pencil.

Consider the following statements: 1. Cherrapunji is located on the south side of Garo hills. 2. Cherrapunji is about 1700 m above mean sea level. Which of the statements given above is/are correct? [IAS 2008] (a) 1 only (b) 2 only (c) Both 1 and 2 (d) Neither 1 nor 2

Description : Consider the following statements: 1. Cherrapunji is located on the south side of Garo hills. 2. Cherrapunji is about 1700 m above mean sea level. Which of the statements given above is/are correct? [IAS 2008] (a) 1 only (b) 2 only (c) Both 1 and 2 (d) Neither 1 nor 2

Last Answer : Ans: (c)

The main function of a muffle in the muffle furnace is to (A) Protect the charge from the effects of the products of combustion (B) Smooth out temperature inequalities on the combustion side of the muffle wall (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The main function of a muffle in the muffle furnace is to (A) Protect the charge from the effects of the products of combustion (B) Smooth out temperature inequalities on the combustion side of the muffle wall (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The efficiency of a pumping set, is generally assumed (A) 50 % (B) 55 % (C) 60 % (D) 65 %

Description : The efficiency of a pumping set, is generally assumed  (A) 50 %  (B) 55 %  (C) 60 %  (D) 65 % 

Last Answer : (D) 65 % 

The permissible amount of nitrites present in potable water, is (A) 10 ppm (B) 15 ppm (C) 45 ppm (D) Nil

Description : The permissible amount of nitrites present in potable water, is (A) 10 ppm (B) 15 ppm (C) 45 ppm (D) Nil

Last Answer : (D) Nil

The prescribed hardness limit of potable water ranges between (A) 50 to 75 P.P.M. (B) 75 to 115 P.P.M. (C) 100 to 150 P.P.M. (D) 150 to 200 P.P.M.

Description : The prescribed hardness limit of potable water ranges between  (A) 50 to 75 P.P.M.  (B) 75 to 115 P.P.M.  (C) 100 to 150 P.P.M.  (D) 150 to 200 P.P.M.

Last Answer : (B) 75 to 115 P.P.M. 

Water used for mixing concrete should be [ A ] Slightly acidic [ B ] Free from bacteria [ C ] Distilled [ D ] Potable

Description : Water used for mixing concrete should be [ A ] Slightly acidic [ B ] Free from bacteria [ C ] Distilled [ D ] Potable

Last Answer : [ D ] Potable

A pushdown automation M = (Q, Σ, Γ, δ, q0, z, F) is set to be deterministic subject to which of the following condition(s), for every q ∈ Q, a ∈ Σ ∪ {λ} and b ∈ Γ (s1) δ(q, a, b) contains at most one element (s2) if δ(q, λ, b) is not empty then δ(q, c, b) must be empty for every c ∈ Σ (A) only s1 (B) only s2 (C) both s1 and s2 (D) neither s1 nor s2

Description : A pushdown automation M = (Q, Σ, Γ, δ, q0, z, F) is set to be deterministic subject to which of the following condition(s), for every q ∈ Q, a ∈ Σ ∪ {λ} and b ∈ Γ (s1) δ(q, a, b) contains at most one ... ) must be empty for every c ∈ Σ (A) only s1 (B) only s2 (C) both s1 and s2 (D) neither s1 nor s2

Last Answer : (C) both s1 and s2

A centrifugal pump is required to be primed before starting if it is located (A) At higher level than water level of reservoir (B) At lower level than water level of reservoir (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : A centrifugal pump is required to be primed before starting if it is located  (A) At higher level than water level of reservoir  (B) At lower level than water level of reservoir  (C) Both (a) and (b)  (D) Neither (a) nor (b) 

Last Answer : (A) At higher level than water level of reservoir

The quantity of seepage of water through soils is proportional to (A) Coefficient of permeability of soil (B) Total head loss through the soil (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : The quantity of seepage of water through soils is proportional to (A) Coefficient of permeability of soil (B) Total head loss through the soil (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option D

Pick up the correct statement from the following: (A) The free water is the amount of water added while mixing and the amount of water held on the surface of the aggregates prior to mixing (B) The total water is the free water and the amount actually absorbed by the aggregates (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : Pick up the correct statement from the following: (A) The free water is the amount of water added while mixing and the amount of water held on the surface of the aggregates prior to mixing (B) The total water ... actually absorbed by the aggregates (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option D

Bitumen felt is used for (A) Water proofing (B) Damp proofing (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Bitumen felt is used for (A) Water proofing (B) Damp proofing (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : Answer: Option C

Increase in water content in a cement concrete (i) Increases workability (ii) Increases the strength [ A ] i [ B ] ii [ C ] both (i) and (ii) [ D ] neither (i) nor (ii)

Description : Increase in water content in a cement concrete (i) Increases workability (ii) Increases the strength [ A ] i [ B ] ii [ C ] both (i) and (ii) [ D ] neither (i) nor (ii)

Last Answer : [ A ] i

In a reservoir the average volume of sediment deposition is 0.15 million cubic per year. If the dead storage and total capacity of the reservoir are 8 million cubic metres and 36 million cubic metres respectively, (A) The reservoir will theoretically be silted in 240 years (B) The reservoir will start reducing after 60 years (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : In a reservoir the average volume of sediment deposition is 0.15 million cubic per year. If the dead storage and total capacity of the reservoir are 8 million cubic metres and 36 million cubic metres respectively, (A) The ... reducing after 60 years (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b)

shaft subjected to a bending moment M and a torque T, experiences (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b) (D) Neither (a) nor (b)

Description :  shaft subjected to a bending moment M and a torque T, experiences  (A) Maximum bending stress = 32M d 3 (B) Maximum shear stress = 16 T d 3 (C) Both (a) and (b)  (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b) 

The slope correction may be ignored if (A) The slope of the ground is less than 3° (B) To slope of the ground is say 1 in 19 (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : The slope correction may be ignored if  (A) The slope of the ground is less than 3°  (B) To slope of the ground is say 1 in 19  (C) Both (a) and (b)  (D) Neither (a) nor (b) 

Last Answer : (C) Both (a) and (b

The Huygens telescope eye piece (A) Is aplanatic (B) Achromatic (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : The Huygens telescope eye piece (A) Is aplanatic (B) Achromatic (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b)

In levelling operation (A) When the instrument is being shifted, the staff must not be moved (B) When the staff is being carried forward, the instrument must remain stationary (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : In levelling operation (A) When the instrument is being shifted, the staff must not be moved (B) When the staff is being carried forward, the instrument must remain stationary (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b)

The method of reversal (A) Is usually directed to examine whether a certain part is truly parallel or perpendicular to another (B) Makes the erroneous relationship between parts evident (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : The method of reversal (A) Is usually directed to examine whether a certain part is truly parallel or perpendicular to another (B) Makes the erroneous relationship between parts evident (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b

Pick up the correct statement from the following: (A) The rate of change of bending moment is equal to rate of shear force (B) The rate of change of shear force is equal to rate of loading (C) Neither (a) nor (b)(D) Both (a) and (b

Description : Pick up the correct statement from the following: (A) The rate of change of bending moment is equal to rate of shear force (B) The rate of change of shear force is equal to rate of loading (C) Neither (a) nor (b) (D) Both (a) and (b

Last Answer : (D) Both (a) and (b

When a cohesionless soil attains quick condition, it looses (A) Shear strength (B) Bearing capacity (C) Both (a) and (b) (D) Neither (a) nor (6

Description : When a cohesionless soil attains quick condition, it looses (A) Shear strength (B) Bearing capacity (C) Both (a) and (b) (D) Neither (a) nor (6

Last Answer : Answer: Option C

Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option D

While propagating through homogeneous, isotropic media, (A) Directions of both the fields are orthogonal (B) Both the fields are at right angles to the direction of propagation (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : While propagating through homogeneous, isotropic media, (A) Directions of both the fields are orthogonal (B) Both the fields are at right angles to the direction of propagation (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : Answer: Option C

According to the Snell's law if an electromagnetic wave is incident in a medium (refractive index n1) on another medium (refractive index m2); (A) The angle of incidence is equal to the angle of refraction (B) The angle of refraction r) is given by sin i (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : According to the Snell's law if an electromagnetic wave is incident in a medium (refractive index n1) on another medium (refractive index m2); (A) The angle of incidence is equal to the angle of refraction (B) The angle of ... r) is given by sin i (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : Answer: Option B

Which one of the following statements regarding remote sensing is correct? (A) The interaction of the electromagnetic radiation with the target (B) The emission of electromagnetic radiation from the target (C) Both (a) and (b) (D) Neither (a) nor (b

Description : Which one of the following statements regarding remote sensing is correct? (A) The interaction of the electromagnetic radiation with the target (B) The emission of electromagnetic radiation from the target (C) Both (a) and (b) (D) Neither (a) nor (b

Last Answer : Answer: Option C

A volume of air at constant barometric pressure may be brought to dew point by (A) Increasing the temperature (B) Decreasing the temperature (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : A volume of air at constant barometric pressure may be brought to dew point by (A) Increasing the temperature (B) Decreasing the temperature (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option B

Pick up the incorrect statement from the following: (A) At two meteorologically homogeneous stations, the average annual precipitation is same (B) If the average annual precipitation at two places is same these are meteorologically homogeneous stations (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : Pick up the incorrect statement from the following: (A) At two meteorologically homogeneous stations, the average annual precipitation is same (B) If the average annual precipitation at two places is same these are ... homogeneous stations (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option B

An aggrading river is a (A) Silting river (B) Scouring river (C) Both silting and scouring river (D) Neither silting nor scouring river

Description : An aggrading river is a (A) Silting river (B) Scouring river (C) Both silting and scouring river (D) Neither silting nor scouring river

Last Answer : Answer: Option A

The safe length L of a valley curve for night travel is (A) 2S - (1.50 + 0.035 S)/N if L < S (B) NS²/(1.50 + 0.035 S) if L > S (C) Neither (a) nor (b)(D) Both (a) and (b

Description : The safe length L of a valley curve for night travel is (A) 2S - (1.50 + 0.035 S)/N if L < S (B) NS²/(1.50 + 0.035 S) if L > S (C) Neither (a) nor (b) (D) Both (a) and (b

Last Answer : Answer: Option D

The distance travelled by revolving the wheel of a vehicle more than its circumferential movement, is known as (A) Slip (B) Skid (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : The distance travelled by revolving the wheel of a vehicle more than its circumferential movement, is known as (A) Slip (B) Skid (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option B

The length of a transition curve, is governed by (A) Rate of change of radial acceleration (B) Rate of change of super-elevation (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : The length of a transition curve, is governed by (A) Rate of change of radial acceleration (B) Rate of change of super-elevation (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : Answer: Option C

The variation of atmospheric potential is caused due to: (A) Difference in temperature over the surface of the earth (B) Change in the density of air (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : The variation of atmospheric potential is caused due to: (A) Difference in temperature over the surface of the earth (B) Change in the density of air (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b)

I.S. Sieve Nos. 10 mm and 4.75 mm are generally used for grading of (A) Coarse aggregates (B) Fine aggregates (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : I.S. Sieve Nos. 10 mm and 4.75 mm are generally used for grading of (A) Coarse aggregates (B) Fine aggregates (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option D

Lime concrete is generally used for (A) Wall foundations (B) Flooring at ground level (C) Both (A) and (B) (D) Neither (A) nor (b)

Description : Lime concrete is generally used for (A) Wall foundations (B) Flooring at ground level (C) Both (A) and (B) (D) Neither (A) nor (b)

Last Answer : Answer: Option B

Stucco paints are suitable for (A) Stone masonry (B) Brick walls (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Stucco paints are suitable for (A) Stone masonry (B) Brick walls (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : Answer: Option C

The entrained concrete is used in lining walls and roofs for making (A) Heat insulated (B) Sound insulated (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : The entrained concrete is used in lining walls and roofs for making (A) Heat insulated (B) Sound insulated (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option D

Consider the following statements: 1. Organic matter decreases the permeability of a soil. 2. Entrapped air decreases the permeability of a soil. Which of these statements are correct? (a) 1 only (b) 2 only (c) Both 1 &2 (d) Neither 1 nor 2

Description : Consider the following statements: 1. Organic matter decreases the permeability of a soil. 2. Entrapped air decreases the permeability of a soil. Which of these statements are correct? (a) 1 only (b) 2 only (c) Both 1 &2 (d) Neither 1 nor 2

Last Answer : (c) Both 1 &2

Consider the following statements: 1. Over the oceans there is more evaporation than precipitation. 2. On land it is more precipitation than evapo-transpiration. Which of these statements are correct? (a) Both 1 & 2 (b) Neither 1 nor 2 (c) 1 only (d) 2 only

Description : Consider the following statements: 1. Over the oceans there is more evaporation than precipitation. 2. On land it is more precipitation than evapo-transpiration. Which of these statements are correct? (a) Both 1 & 2 (b) Neither 1 nor 2 (c) 1 only (d) 2 only

Last Answer : (a) Both 1 & 2

Strain compatibility method is the method used for the analysis and design of [ A ] singly reinforced sections [ B ] doubly reinforced sections [ C ] both (a) and (b) [ D ] neither (a) nor (b)

Description : Strain compatibility method is the method used for the analysis and design of [ A ] singly reinforced sections [ B ] doubly reinforced sections [ C ] both (a) and (b) [ D ] neither (a) nor (b)

Last Answer : [ C ] both (a) and (b)

Strain compatibility method is the method used for the analysis and design of [ A ] singly reinforced sections [ B ] doubly reinforced sections [ C ] both (a) and (b) [ D ] neither (a) nor (b)

Description : Strain compatibility method is the method used for the analysis and design of [ A ] singly reinforced sections [ B ] doubly reinforced sections [ C ] both (a) and (b) [ D ] neither (a) nor (b)

Last Answer : [ C ] both (a) and (b)

When the reduced level of the water source is higher than the reduced level of the consumer's place, water is generally supplied (A) By pumping system (B) By gravitational system (C) Both (a) and (b) (D) All the above

Description : When the reduced level of the water source is higher than the reduced level of the consumer's  place, water is generally supplied  (A) By pumping system  (B) By gravitational system  (C) Both (a) and (b)  (D) All the above 

Last Answer : (B) By gravitational system 

Check valves are used (A) At high pressure (B) In bends (C) For controlling water flow (D) For unidirectional flow

Description : Check valves are used (A) At high pressure (B) In bends (C) For controlling water flow (D) For unidirectional flow

Last Answer : (D) For unidirectional flow