A centrifugal pump is required to be primed before starting if it is located (A) At higher level than water level of reservoir (B) At lower level than water level of reservoir (C) Both (a) and (b) (D) Neither (a) nor (b)

A centrifugal pump is required to be primed before starting if it is located 

(A) At higher level than water level of reservoir 

(B) At lower level than water level of reservoir 

(C) Both (a) and (b) 

(D) Neither (a) nor (b) 

by

1 Answer

Answer :

(A) At higher level than water level of reservoir

by

Related questions

In centrifugal pump installation, (A) Pump is properly primed before starting (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe (C) The motor may burn out if it is started with empty delivery pipe and with open gate valve (D) All the above

Description : In centrifugal pump installation,  (A) Pump is properly primed before starting  (B) The diameter of the pipe at inlet as well as at outlet, is kept smaller than the delivery pipe  (C) The ... out if it is started with empty delivery pipe and with open gate valve  (D) All the above 

Last Answer : (D) All the above 

Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : C) Both (A) and (B)

In a reservoir the average volume of sediment deposition is 0.15 million cubic per year. If the dead storage and total capacity of the reservoir are 8 million cubic metres and 36 million cubic metres respectively, (A) The reservoir will theoretically be silted in 240 years (B) The reservoir will start reducing after 60 years (C) Both (a) and (b) (D) Neither (a) nor (b)

Description : In a reservoir the average volume of sediment deposition is 0.15 million cubic per year. If the dead storage and total capacity of the reservoir are 8 million cubic metres and 36 million cubic metres respectively, (A) The ... reducing after 60 years (C) Both (a) and (b) (D) Neither (a) nor (b)

Last Answer : (C) Both (a) and (b)

In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Description : In centrifugal pump operation, the cavitation can be eliminated by maintaining suction pressure __________ the vapor pressure of the liquid at the suction temperature. (A) Lower than (B) Higher than (C) Equal to (D) None of these

Last Answer : (B) Higher than

To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length of the pipe is 1506 m and f = 0.01, ignoring other minor losses and assuming the economical diameter from Lea's formula D = 1.2 Q, the water horse power of the pump is (A) 400 (B) 450 (C) 500(D) 600

Description : To pump water from a water reservoir 3 m deep and maximum water level at 135 m, a pump is  installed to lift water up to R.L. 175 m at a constant rate of 36,00,000 litres per hour. If the length  of the ... the water horse power of the pump is  (A) 400  (B) 450  (C) 500 (D) 600

Last Answer : (D) 600

Pick up the correct statement from the following regarding radial flow centrifugal pumps: (A) These are provided with volute type or turbine type casings (B) In involute type of radial flow centrifugal pump, the impeller discharges into a gradually expanding spiral casing (C) The efficiency of turbine type of radial flow centrifugal pump, is always higher than that of volute type (D) All the above

Description : Pick up the correct statement from the following regarding radial flow centrifugal pumps:  (A) These are provided with volute type or turbine type casings  (B) In involute type of radial flow ... centrifugal pump, is always higher than that of  volute type  (D) All the above 

Last Answer : (D) All the above 

Thermal efficiency of a Carnot engine can approach 100%, only when the temperature of the (A) Cold reservoir approaches zero (B) Hot reservoir approaches infinity (C) Either (A) or (B) (D) Neither (A) nor (B)

Description : Thermal efficiency of a Carnot engine can approach 100%, only when the temperature of the (A) Cold reservoir approaches zero (B) Hot reservoir approaches infinity (C) Either (A) or (B) (D) Neither (A) nor (B)

Last Answer : C) Either (A) or (B)

Coke oven gas produced by high temperature carbonisation of coal (as compared to that produced by low temperature carbonisation), has (A) Higher calorific value (B) Lower hydrogen content (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Coke oven gas produced by high temperature carbonisation of coal (as compared to that produced by low temperature carbonisation), has (A) Higher calorific value (B) Lower hydrogen content (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (D) Neither (A) nor (B)

The depth of the water table at a place is 45 m below the general ground level. To lift water from a deep tube well in such a locality, the type of pump to be installed is (A) Centrifugal pump (B) Reciprocating pump (C) Deep well turbine pump (D) None of these

Description : The depth of the water table at a place is 45 m below the general ground level. To lift water from a  deep tube well in such a locality, the type of pump to be installed is  (A) Centrifugal pump  (B) Reciprocating pump  (C) Deep well turbine pump  (D) None of these 

Last Answer : (C) Deep well turbine pump

While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Description : While starting a centrifugal pump, its delivery valve should be kept (A) Opened (B) Closed (C) Either opened or closed; it does not make any difference (D) Either opened or closed; depending on the fluid viscosity

Last Answer : (B) Closed

A centrifugal pump loses prime after starting. The reason of this trouble may be (A) Incomplete priming (B) Too high a suction lift (C) Low available NPSH and air leaks in the suction pipe (D) All (A), (B), and (C)

Description : A centrifugal pump loses prime after starting. The reason of this trouble may be (A) Incomplete priming (B) Too high a suction lift (C) Low available NPSH and air leaks in the suction pipe (D) All (A), (B), and (C)

Last Answer : (D) All (A), (B), and (C)

Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Last Answer : (A) Cavitation

A centrifugal pump designed to pump water is employed to pump a more viscous oil. In the later case, the pump (A) Develops a lower head (B) Capacity is reduced (C) Requires more power (D) All (A), (B) and (C)

Description : A centrifugal pump designed to pump water is employed to pump a more viscous oil. In the later case, the pump (A) Develops a lower head (B) Capacity is reduced (C) Requires more power (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)

Description : Factor of safety against sliding of a slope, is the ratio of (A) Actual cohesion to that required to maintain stability of slope (B) Shear strength to shear stress along the surface (C) Neither (a) nor (b) (D) Both (a) and (b)

Last Answer : Answer: Option D

Consider the following statements: 1. Cherrapunji is located on the south side of Garo hills. 2. Cherrapunji is about 1700 m above mean sea level. Which of the statements given above is/are correct? [IAS 2008] (a) 1 only (b) 2 only (c) Both 1 and 2 (d) Neither 1 nor 2

Description : Consider the following statements: 1. Cherrapunji is located on the south side of Garo hills. 2. Cherrapunji is about 1700 m above mean sea level. Which of the statements given above is/are correct? [IAS 2008] (a) 1 only (b) 2 only (c) Both 1 and 2 (d) Neither 1 nor 2

Last Answer : Ans: (c)

Reciprocating pumps are not able to compete with the centrifugal pump for industrial use, mainly because these pumps have (A) Very low speeds (B) Smaller discharge (C) Higher capital &maintenance cost (D) High vibrations

Description : Reciprocating pumps are not able to compete with the centrifugal pump for industrial use, mainly because these pumps have (A) Very low speeds (B) Smaller discharge (C) Higher capital &maintenance cost (D) High vibrations

Last Answer : (C) Higher capital &maintenance cost

Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Description : Higher specific speed (200-500) of a centrifugal pump indicates that the pump is of __________ flow type. (A) Axial (B) Radial (C) Mixed (D) None of these

Last Answer : (A) Axial

To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Description : To handle smaller quantity of fluid at higher discharge pressure, use a __________ pump. (A) Reciprocating (B) Centrifugal (C) Volute (D) Rotary vacuum

Last Answer : (A) Reciprocating

Lime concrete is generally used for (A) Wall foundations (B) Flooring at ground level (C) Both (A) and (B) (D) Neither (A) nor (b)

Description : Lime concrete is generally used for (A) Wall foundations (B) Flooring at ground level (C) Both (A) and (B) (D) Neither (A) nor (b)

Last Answer : Answer: Option B

Starting material for the production of SBR is (A) Ethyl alcohol (B) Ethylene (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Starting material for the production of SBR is (A) Ethyl alcohol (B) Ethylene (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The resource-based perspective suggests that unique firm resources should be the starting point for developing successful strategies a) the business opportunity should be the starting point for developing successful strategiesb) unique firm resources should be the starting point for developing successful strategies.c) both business opportunity and unique firm resources should be the starting point for developing successful strategies.d) neither business opportunity nor unique firm resources should be the starting point for developing successful strategies.

Description : The resource-based perspective suggests that unique firm resources should be the starting point for developing successful strategies a) the business opportunity should be the starting point for ... nor unique firm resources should be the starting point for developing successful strategies.

Last Answer : unique firm resources should be the starting point for developing successful strategies.

Starting material for the production of styrene butadiene rubber (SBR) is (A) Ethyl alcohol (B) Ethylene (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Starting material for the production of styrene butadiene rubber (SBR) is (A) Ethyl alcohol (B) Ethylene (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

A single-phase induction motor starts, comes up to about 75% rated speed, slows down to a lower speed, and accelerates again. The problem is most likely in the ____________. A. starting winding B. running winding C. starting capacitor D. running centrifugal switch

Description : A single-phase induction motor starts, comes up to about 75% rated speed, slows down to a lower speed, and accelerates again. The problem is most likely in the ____________. A. starting winding B. running winding C. starting capacitor D. running centrifugal switch

Last Answer : Answer: B

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Power required by a centrifugal pump is proportional to (where, D = diameter, N = r.p.m) (A) N2D3 (B) ND2 (C) N2D (D) N3D5

Description : Power required by a centrifugal pump is proportional to (where, D = diameter, N = r.p.m) (A) N2D3 (B) ND2 (C) N2D (D) N3D5

Last Answer : (D) N3D5

If the head is doubled in & centrifugal pump, the power required will increase in the ratio of (A) 23 (B) 23/2 (C) 25/2 (D) 21/3

Description : If the head is doubled in & centrifugal pump, the power required will increase in the ratio of (A) 23 (B) 23/2 (C) 25/2 (D) 21/3

Last Answer : B) 23/2

In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) Discharge of water by a centrifugal pump being run at a constant rpm (B) Water flow in the suction and discharge pipe of a reciprocating pump (C) Water discharge from a vertical vessel in which constant level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Description : In case of unsteady fluid flow, conditions & flow pattern change with the passage of time at a position in a flow situation. Which of the following is an example of unsteady flow? (A) ... level is maintained (D) Low velocity flow of a highly viscous liquid through a hydraulically smooth pipe

Last Answer : (B) Water flow in the suction and discharge pipe of a reciprocating pump

The main draw-back of centrifugal pump, is (A) Necessity of priming (B) Discharge from pump varies with the load of water (C) For high heads, efficiency is low up to 50% (D) All the above

Description : The main draw-back of centrifugal pump, is (A) Necessity of priming (B) Discharge from pump varies with the load of water (C) For high heads, efficiency is low up to 50% (D) All the above

Last Answer : (D) All the above

Most commonly used pump for lifting water in water supply mains, is (A) Axial flow pump (B) Reciprocating pump (C) Rotary type pump (D) Centrifugal pumps

Description : Most commonly used pump for lifting water in water supply mains, is  (A) Axial flow pump  (B) Reciprocating pump  (C) Rotary type pump  (D) Centrifugal pumps 

Last Answer : (A) Axial flow pump 

Actual flame temperature is always lower than the adiabatic flame temperature, because there is (A) No possibility of obtaining complete combustion at high temperature (B) Always loss of heat from the flame (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Actual flame temperature is always lower than the adiabatic flame temperature, because there is (A) No possibility of obtaining complete combustion at high temperature (B) Always loss of heat from the flame (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Description : Conversion of dynamic velocity head into static pressure head in a centrifugal pump is the result of : (a) Increasing area of flow between adjacent vanes from inlet to outlet (b) Difference in pressure between suction and delivery ends (c) Radial thrust in pumps (d) Stuffing Box

Last Answer : (b) Difference in pressure between suction and delivery ends

Starting raw material for the manufacture of Maleic anhydride is (A) n-butene (B) Benzene (C) Either (A) or (B) (D) Neither (A) nor (B)

Description : Starting raw material for the manufacture of Maleic anhydride is (A) n-butene (B) Benzene (C) Either (A) or (B) (D) Neither (A) nor (B)

Last Answer : (C) Either (A) or (B)

In catalytic alkylation, higher iso-butane to olefin ratio gives (A) Low final boiling point product (B) Higher yield (C) Both (A) and (B) (D) Neither (A) nor (B

Description : In catalytic alkylation, higher iso-butane to olefin ratio gives (A) Low final boiling point product (B) Higher yield (C) Both (A) and (B) (D) Neither (A) nor (B

Last Answer : (A) Low final boiling point product

Higher vapour pressure of gasoline indicates(A) Low flash point(B) High breathing loss(C) Both (A) and (B)(D) Neither (A) nor (B

Description : Higher vapour pressure of gasoline indicates (A) Low flash point (B) High breathing loss (C) Both (A) and (B) (D) Neither (A) nor (B

Last Answer : (D) Neither (A) nor (B

Steam distillation is used for separation of high boiling (A) Substances from non-volatile impurities (B) Volatile impurity from still higher boiling substances (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Steam distillation is used for separation of high boiling (A) Substances from non-volatile impurities (B) Volatile impurity from still higher boiling substances (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

For the reversible exothermic reaction, N2 + 3H2 ⇌ 2NH3, increase of pressure would (A) Shift the equilibrium towards right (B) Give higher yield of NH3 (C) Both (B) and (C) (D) Neither (A) nor (B)

Description : For the reversible exothermic reaction, N2 + 3H2 ⇌ 2NH3, increase of pressure would (A) Shift the equilibrium towards right (B) Give higher yield of NH3 (C) Both (B) and (C) (D) Neither (A) nor (B)

Last Answer : (C) Both (B) and (C)

A boy presses a side of a blue pencil to a side of a yellow pencil, holding both pencils vertically. One inch of the pressed side of the blue pencil, measuring from its lower end, is smeared with paint. The yellow pencil is held steady while the boy slides the blue pencil down 1 inch, continueing to press it against the yellow one. He returns the blue pencil to its former position, then again it slides down 1 inch. He continues until he has lowered the blue pencil 5 times and raised it 5 times- 10 moves in all.Supposed that during this time the paint neither dries nor diminishes in quantity. How many inches of each pencil will be sneared with paint after the tenth move? -Riddles

Description : A boy presses a side of a blue pencil to a side of a yellow pencil, holding both pencils vertically. One inch of the pressed side of the blue pencil, measuring from its lower end, is smeared ... in quantity. How many inches of each pencil will be sneared with paint after the tenth move? -Riddles

Last Answer : At the start, 1inch of the yellow pencil gets smeared with wet paint. As the blue pencil is moved downward, a second inch of the blue pencils smears a second inch of the yellow pencil. Each pair ... of moves will smear 5 inches. This together with the initial inch, makes 6 inches for each pencil.

Consider the following statements: 1. A flute of smaller length produces waves of lower frequency. 2. Sound travels in rocks in the form of longitudinal elastic waves only. Which of the statements given above is/are correct? (a) 1 only (b) 2 only (c) Both 1 and 2 (d) Neither 1 nor 2

Description : Consider the following statements: 1. A flute of smaller length produces waves of lower frequency. 2. Sound travels in rocks in the form of longitudinal elastic waves only. Which of the statements given above is/are correct? (a) 1 only (b) 2 only (c) Both 1 and 2 (d) Neither 1 nor 2

Last Answer : Ans:(d)

Plutonium (A) Is recovered from spent fuel from thermal nuclear reactor (B) Has much lower melting point (640°C ) compared to thorium (1690°C) (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Plutonium (A) Is recovered from spent fuel from thermal nuclear reactor (B) Has much lower melting point (640°C ) compared to thorium (1690°C) (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B

Which of the following statements are true of the multiple organ dysfunction syndrome (MODS)? A. The “two-hit” model proposes that secondary MODS may be produced when even a relatively minor second insult reactivates, in a more amplified form, the systemic inflammatory response that was primed by an initial insult to the host. B. The systemic inflammatory response syndrome (SIRS), shock due to sepsis or SIRS, and MODS may be regarded as a continuum of illness severity. C. Prolonged stimulation or activation of Kupffer cells in the liver is thought to be a critical factor in the sustained, uncontrolled release of inflammatory mediators. D. The incidence of MODS in intensive care units has decreased owing to increased awareness, prevention, and treatment of the syndrome.

Description : Which of the following statements are true of the multiple organ dysfunction syndrome (MODS)? A. The two-hit model proposes that secondary MODS may be produced when even a relatively ... intensive care units has decreased owing to increased awareness, prevention, and treatment of the syndrome.

Last Answer : Answer: ABC DISCUSSION: MODS is part of a clinical continuum that begins with the systemic inflammatory response syndrome, which is the host's stress response to any major insult such ... pathogenesis of MODS, the incidence of MODS continues to increase without a significant improvement in outcome

Why are the walls primed and how to do it correctly?

Description : Why are the walls primed and how to do it correctly?

Last Answer : Why are the walls primed and how to do it correctly? The upcoming renovation scares almost everyone, but it is especially scary for those who decided to do it on their own. Nothing is impossible, the ... 's all - the walls are ready for further wallpapering or painting. Let the renovation be a joy!

The disintegrating pump in which solid matter is broken up before passing out, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Description : The disintegrating pump in which solid matter is broken up before passing out, is A. Centrifugal pump B. Reciprocating pump C. Pneumatic ejector D. None of these

Last Answer : ANS: A

Pick up the correct statement from the following: (A) The earth work of cutting in trenches or borrow pits in fairly uniform ground is measured with the help of average depths of the dead men (B) The earth work in trenches or borrow pits in irregular ground is measured by taking the difference in levels before and after completion of work (C) The earth work in trenches or borrow pits, where neither a nor b is feasible, are measured from the fillings after deduction of voids (D) All the above

Description : Pick up the correct statement from the following: (A) The earth work of cutting in trenches or borrow pits in fairly uniform ground is measured with the help of average depths of the dead men (B) ... a nor b is feasible, are measured from the fillings after deduction of voids (D) All the above

Last Answer : (D) All the above

Critical time for developing a water hammer, is the time required for (A) Closing the valve (B) The wave to travel from valve to the reservoir (C) The wave to travel from the valve to the reservoir and back (D) None of these

Description : Critical time for developing a water hammer, is the time required for  (A) Closing the valve  (B) The wave to travel from valve to the reservoir  (C) The wave to travel from the valve to the reservoir and back  (D) None of these 

Last Answer : (C) The wave to travel from the valve to the reservoir and back 

Reduced voltage applied to a motor during the starting period will _____________. A. result in decreased acceleration time only B. lower the starting current and increase accelerating time C. cause a greater starting torque D. increase the starting current and pump capacity

Description : Reduced voltage applied to a motor during the starting period will _____________. A. result in decreased acceleration time only B. lower the starting current and increase accelerating time C. cause a greater starting torque D. increase the starting current and pump capacity

Last Answer : Answer: B

Horsepower required for a roll crusher is directly proportional to its (A) Reduction ratio (B) Capacity(C) Both (A) & (B)(D) Neither (A) nor (B)

Description : Horsepower required for a roll crusher is directly proportional to its (A) Reduction ratio (B) Capacity (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The amount of steam required per unit quantity of distillate in case of steam distillation will be reduced by (A) Raising the temperature (B) Lowering the total pressure (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : The amount of steam required per unit quantity of distillate in case of steam distillation will be reduced by (A) Raising the temperature (B) Lowering the total pressure (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B

What are the irregularities which are required to be brought to the notice of the postmaster by the sub account assistant? a) When the amount held in cash by a SO exceeds the authorized max balance and cash is held below the authorized balance b) When the stamps are not sold by SO c) Both the A and B d) Neither A Nor B

Description : What are the irregularities which are required to be brought to the notice of the postmaster by the sub account assistant? a) When the amount held in cash by a SO exceeds the authorized max balance and cash is held ... b) When the stamps are not sold by SO c) Both the A and B d) Neither A Nor B

Last Answer : a) When the amount held in cash by a SO exceeds the authorized max balance and cash is held below the authorized balance

Pick up the correct statement from the following: (A) If ports are closed, the dry intake towers will not have any water (B) Even if ports are closed, the wet intake tower will have water filled up to reservoir level (C) No buoyant force acts on wet intake towers (D) All the above

Description : Pick up the correct statement from the following:  (A) If ports are closed, the dry intake towers will not have any water  (B) Even if ports are closed, the wet intake tower will have water ... to reservoir level  (C) No buoyant force acts on wet intake towers  (D) All the above 

Last Answer : (D) All the above