Consider the production of ammonia from methene and air as raw materials. The catalysts used are: (i) __________ for steam reforming of methane and (ii) __________ for ammonia synthesis. (A) (i) - Ni/Al2O3 ; (ii) - Cu - ZnO/Al2O3 (B) (i) - Fe/Al2O3 ; (ii) - Cu - ZnO/Al2O3 (C) (i) - Ni/Al2O3 ; (ii) - Fe/Al2O3 (D) (i) - Fe/Al2O3 ; (ii) - Ni/Al2O3

Consider the production of ammonia from methene and air as raw
materials. The catalysts used are: (i) __________ for steam reforming of
methane and (ii) __________ for ammonia synthesis.
(A) (i) - Ni/Al2O3
; (ii) - Cu - ZnO/Al2O3
(B) (i) - Fe/Al2O3
; (ii) - Cu - ZnO/Al2O3
(C) (i) - Ni/Al2O3
; (ii) - Fe/Al2O3
(D) (i) - Fe/Al2O3
; (ii) - Ni/Al2O3
by

1 Answer

Answer :

(C) (i) - Ni/Al2O3
; (ii) - Fe/Al2O3
by

Related questions

Catalyst used in ammonia synthesis uses __________ as a promoter. (A) Pt (B) K2O (C) Al2O3 (D) Ni

Description : Catalyst used in ammonia synthesis uses __________ as a promoter. (A) Pt (B) K2O (C) Al2O3 (D) Ni

Last Answer : (B) K2O

Fat splitting catalyst is(A) CaCO3(B) ZnO(C) Al2O3(D) Fe

Description : Fat splitting catalyst is (A) CaCO3 (B) ZnO (C) Al2O3 (D) Fe

Last Answer : (B) ZnO

Which of the following is the costliest method for commercial production of hydrogen for ammonia synthesis? (A) H2 separation from coke oven gas(B) Steam reforming of naphtha(C) Cracking of natural gas(D) Electrolysis of water

Description : Which of the following is the costliest method for commercial production of hydrogen for ammonia synthesis? (A) H2 separation from coke oven ga (B) Steam reforming of naphtha (C) Cracking of natural gas (D) Electrolysis of water

Last Answer : (D) Electrolysis of water

Steam reforming of naphtha produces ammonia synthesis gas. This is a/an __________ process. (A) Autocatalytic (B) Endothermic (C) Exothermic (D) Non-catalytic

Description : Steam reforming of naphtha produces ammonia synthesis gas. This is a/an __________ process. (A) Autocatalytic (B) Endothermic (C) Exothermic (D) Non-catalytic

Last Answer : (B) Endothermic

Ammonia synthesis gas is produced from fuel oil by (A) Steam reforming (B) Hydro-cracking (C) Partial oxidation (D) Hydrogenation

Description : Ammonia synthesis gas is produced from fuel oil by (A) Steam reforming (B) Hydro-cracking (C) Partial oxidation (D) Hydrogenation

Last Answer : (C) Partial oxidation

Ammonia synthesis gas is produced from natural gas by (A) Thermal cracking (B) Steam reforming (C) Partial oxidation (D) Hydrogenation

Description : Ammonia synthesis gas is produced from natural gas by (A) Thermal cracking (B) Steam reforming (C) Partial oxidation (D) Hydrogenation

Last Answer : (B) Steam reforming

Limestone addition in the blast furnace is done to flux __________ present in the raw materials. (A) SiO2 (B) Al2O3 (C) MnO2 (D) P

Description : Limestone addition in the blast furnace is done to flux __________ present in the raw materials. (A) SiO2 (B) Al2O3 (C) MnO2 (D) P

Last Answer : Limestone addition in the blast furnace is done to flux __________ present in the raw materials. (A) SiO2 (B) Al2O3 (C) MnO2 (D) P

Constantan is an alloy of (A) Cu (55%) & Sn (45%) (B) Cu (55%) & Ni (45%) (C) Pt (95%) & Rh (10%) (D) Fe (80%) & Ni (20%)

Description : Constantan is an alloy of (A) Cu (55%) & Sn (45%) (B) Cu (55%) & Ni (45%) (C) Pt (95%) & Rh (10%) (D) Fe (80%) & Ni (20%)

Last Answer : (B) Cu (55%) & Ni (45%)

The trace metal present in insulin is (A) Cu (B) Zn (C) Fe (D) Ni

Description : The trace metal present in insulin is (A) Cu (B) Zn (C) Fe (D) Ni

Last Answer : (B) Zn

Which is a catalyst promoter used in catalytic ammonia synthesis reaction? (A) Al2O3 (B) Cr2O3 (C) K2O (D) MnO

Description : Which is a catalyst promoter used in catalytic ammonia synthesis reaction? (A) Al2O3 (B) Cr2O3 (C) K2O (D) MnO

Last Answer : (C) K2O

What are amphoteric oxides? Choose the amphoteric oxides from amongst the following oxides: Na2O, ZnO, Al2O3, CO2, H2O -Chemistry

Description : What are amphoteric oxides? Choose the amphoteric oxides from amongst the following oxides: Na2O, ZnO, Al2O3, CO2, H2O -Chemistry

Last Answer : Those oxides which reacts with acids as well as bases to produce salts and water are called amphoteric oxides, e.g. Na2O, ZnO, are amphoteric oxides among given oxides.

Pick out the wrong statement. (A) Use of different catalysts in a reversible catalytic chemical reaction does not change the equilibrium composition (B) Alumina is added as a promoter to iron catalyst in ammonia synthesis reaction (C) Activation energy for a reaction is obtained from the intercept of the Arrhenius plot (D) Presence of inerts affects the equilibrium conversion of reactants in a chemical reaction

Description : Pick out the wrong statement. (A) Use of different catalysts in a reversible catalytic chemical reaction does not change the equilibrium composition (B) Alumina is added as a promoter to ... Arrhenius plot (D) Presence of inerts affects the equilibrium conversion of reactants in a chemical reaction

Last Answer : (C) Activation energy for a reaction is obtained from the intercept of the Arrhenius plot

__________ is used as a catalyst in fat splitting. (A) ZnO (B) Ni (C) V2O5 (D) FeO

Description : __________ is used as a catalyst in fat splitting. (A) ZnO (B) Ni (C) V2O5 (D) FeO

Last Answer : (A) ZnO

The core metal of chlorophyll is (a) Ni (b) Cu (c) Fe (d) Mg.

Description : The core metal of chlorophyll is (a) Ni (b) Cu (c) Fe (d) Mg.

Last Answer : d) Mg.

The deficiencies of micronutrients, not only affect growth of plants but also vital functions such as photosynthetic and mitochondrial electron flow. Among the list given below, which group of three elements shall affect most, both photosynthetic and mitochondrial electron transport?(a) Co, Ni, Mo (b) Ca, K, Na (c) Mn, Co, Ca (d) Cu, Mn, Fe

Description : The deficiencies of micronutrients, not only affect growth of plants but also vital functions such as photosynthetic and mitochondrial electron flow. Among the list given below, which group of three elements shall affect most, both ... , Mo (b) Ca, K, Na (c) Mn, Co, Ca (d) Cu, Mn, Fe

Last Answer : d) Cu, Mn, Fe

Which of the following is the costliest source of hydrogen needed for ammonia manufacture under Indian condition? (A) Electrolysis of water (B) Cryogenic removal of H2 from coke oven gas (C) Steam reforming of naphtha (D) Natural gas cracking

Description : Which of the following is the costliest source of hydrogen needed for ammonia manufacture under Indian condition? (A) Electrolysis of water (B) Cryogenic removal of H2 from coke oven gas (C) Steam reforming of naphtha (D) Natural gas cracking

Last Answer : (A) Electrolysis of water

Manufacture of phthalic anhydride uses __________ as a catalyst. (A) Ni (B) Cr (C) V2O5 (D) Al2O3

Description : Manufacture of phthalic anhydride uses __________ as a catalyst. (A) Ni (B) Cr (C) V2O5 (D) Al2O3

Last Answer : (C) V2O5

Nickel is not used as a catalyst in the __________ reaction. (A) Shift conversion (B) Oil hydrogenation (C) Steaming reforming of naphtha (D) Ammonia cracking/dissociation

Description : Nickel is not used as a catalyst in the __________ reaction. (A) Shift conversion (B) Oil hydrogenation (C) Steaming reforming of naphtha (D) Ammonia cracking/dissociation

Last Answer : (A) Shift conversion

Steam reforming of naphtha is a source of hydrogen production for nitrogenous fertiliser industry. What is the usual ratio of steam to carbon maintained in the process of steam reforming of naphtha? (A) 1.5 : 1 (B) 3.5 : 1 (C) 10 : 1 (D) 15 : 1

Description : Steam reforming of naphtha is a source of hydrogen production for nitrogenous fertiliser industry. What is the usual ratio of steam to carbon maintained in the process of steam reforming of naphtha? (A) 1.5 : 1 (B) 3.5 : 1 (C) 10 : 1 (D) 15 : 1

Last Answer : (B) 3.5 : 1

Commercial production of hydrogen for the manufacture of nitrogenous fertilisers is done by (A) Steam reforming of naphtha and cracking of natural gas (B) Electrolysis of water (C) Cryogenic separation of hydrogen from coke oven gas (D) All (A), (B) and (C)

Description : Commercial production of hydrogen for the manufacture of nitrogenous fertilisers is done by (A) Steam reforming of naphtha and cracking of natural gas (B) Electrolysis of water (C) Cryogenic separation of hydrogen from coke oven gas (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Raw materials for nitric acid manufacture are (A) Hydrogen peroxide, air and water (B) Anhydrous ammonia and air (C) Anhydrous ammonia, air and water (D) Wet ammonia, air and water

Description : Raw materials for nitric acid manufacture are (A) Hydrogen peroxide, air and water (B) Anhydrous ammonia and air (C) Anhydrous ammonia, air and water (D) Wet ammonia, air and water

Last Answer : (C) Anhydrous ammonia, air and water

Pick out the wrong statement. (A) Addition of methane to the furnace atmosphere reduces decarburising by hydrogen (B) Nitrogen in presence of steam decor-burises high carbon steel, whereas hydrocarbon gases carburise the surface of steel at annealing temperatures (C) Active nitrogen (formed by cracking ammonia at the metal surface) cause nitride formation with increase in surface hardness (D) None of these

Description : Pick out the wrong statement. (A) Addition of methane to the furnace atmosphere reduces decarburising by hydrogen (B) Nitrogen in presence of steam decor-burises high carbon steel, whereas hydrocarbon ... the metal surface) cause nitride formation with increase in surface hardness (D) None of these

Last Answer : (D) None of these

Which of the following agents is used in order to make benzene react with bromine to give bromobenzene? (a) Ultraviolet light (b) Fe catalyst (c) Nickel catalyst (d) Al2O3 catalyst

Description : Which of the following agents is used in order to make benzene react with bromine to give bromobenzene? (a) Ultraviolet light (b) Fe catalyst (c) Nickel catalyst (d) Al2O3 catalyst

Last Answer : Fe catalyst

Solvent naphtha' used mostly as a solvent in paints and perfumery is produced by the __________ of virgin naphtha into small boiling range cuts. (A) Steam reforming (B) Distillation (C) Desulphurisation (D) None of these

Description : Solvent naphtha' used mostly as a solvent in paints and perfumery is produced by the __________ of virgin naphtha into small boiling range cuts. (A) Steam reforming (B) Distillation (C) Desulphurisation (D) None of these

Last Answer : (B) Distillation

Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200

Description : Optimum reaction temperature in steam reforming of naphtha is __________ °C. (A) 700 - 1000 (B) 300 - 450 (C) 1500-1700 (D) 100-200

Last Answer : (A) 700 - 1000

Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of Portland cement. The component of Portland cement which first hardens is (A) 5CaO. 3 Al2O3 (B) 3CaO. Al2O3 (C) 3CaO. SiO2 (D) 2CaO. SiO2

Description : Alumina, silica, lime and iron oxide are the basic raw material for the manufacture of Portland cement. The component of Portland cement which first hardens is (A) 5CaO. 3 Al2O3 (B) 3CaO. Al2O3 (C) 3CaO. SiO2 (D) 2CaO. SiO2

Last Answer : Option A

Cold dil. `H_(2)SO_(4)` will completely dissolve : (i) Pb (ii) `Fe_(3)O_(4)` (iii) Fe (iv) Cu (v) Mg (vi) MgO (vii) `CoCO_(3)` (viii) `CuCO_(2)` (ix)

Description : Cold dil. `H_(2)SO_(4)` will completely dissolve : (i) Pb (ii) `Fe_(3)O_(4)` (iii) Fe (iv) Cu (v) Mg (vi) MgO (vii) `CoCO_(3)` (viii) `CuCO_(2)` (ix)

Last Answer : Cold dil. `H_(2)SO_(4)` will completely dissolve : (i) Pb (ii) `Fe_(3)O_(4)` (iii) Fe (iv) Cu (v) ... ) `CoCO_(3)` (viii) `CuCO_(2)` (ix) `SrCO_(3)`

Cold dil. `H_(2)SO_(4)` will completely dissolve : (i) Pb (ii) `Fe_(3)O_(4)` (iii) Fe (iv) Cu (v) Mg (vi) MgO (vii) `CoCO_(3)` (viii) `CuCO_(2)` (ix)

Description : Cold dil. `H_(2)SO_(4)` will completely dissolve : (i) Pb (ii) `Fe_(3)O_(4)` (iii) Fe (iv) Cu (v) Mg (vi) MgO (vii) `CoCO_(3)` (viii) `CuCO_(2)` (ix)

Last Answer : Cold dil. `H_(2)SO_(4)` will completely dissolve : (i) Pb (ii) `Fe_(3)O_(4)` (iii) Fe (iv) Cu (v) ... ) `CoCO_(3)` (viii) `CuCO_(2)` (ix) `SrCO_(3)`

Bessemerization is carried out for (I) Fe (II) Cu (III) Al (IV) silver

Description : Bessemerization is carried out for (I) Fe (II) Cu (III) Al (IV) silver

Last Answer : Bessemerization is carried out for (I) Fe (II) Cu (III) Al (IV) silver A. I,II B. II,III C. I,III D. All

Raw materials for 'Solvay Process' for manufacture of the soda ash are (A) Salt, limestone and coke or gas(B) Ammonia, salt and limestone(C) Ammonia limestone and coke(D) None of these

Description : Raw materials for 'Solvay Process' for manufacture of the soda ash are (A) Salt, limestone and coke or gas (B) Ammonia, salt and limestone (C) Ammonia limestone and coke (D) None of these

Last Answer : (A) Salt, limestone and coke or gas

Pick out the wrong statement. (A) Catalytic hydrogenation of carbon monoxide produces methyl alcohol (B) In nylon-6, the number 6 represents the total number of carbon atoms in the ring (C) Raw materials for DDT manufacture are benzene and chlorine (D) Ethanolamines are produced by using ammonia and ethylene oxide as raw material

Description : Pick out the wrong statement. (A) Catalytic hydrogenation of carbon monoxide produces methyl alcohol (B) In nylon-6, the number 6 represents the total number of carbon atoms in the ring (C ... are benzene and chlorine (D) Ethanolamines are produced by using ammonia and ethylene oxide as raw material

Last Answer : (C) Raw materials for DDT manufacture are benzene and chlorine

Which raw material is used to impart colour to the glass? a) Al2O3 b) CoO c) CaO d) MgO

Description : Which raw material is used to impart colour to the glass? a) Al2O3 b) CoO c) CaO d) MgO

Last Answer : b) CoO

Commercial production of calcium carbide requires limestone and __________ as raw materials. (A) Coke (B) Sand (C) Soda ash (D) Fuel oil

Description : Commercial production of calcium carbide requires limestone and __________ as raw materials. (A) Coke (B) Sand (C) Soda ash (D) Fuel oil

Last Answer : (B) Sand

Commercial production of soda ash by Solvay process requires limestone, __________ as raw materials. (A) Coke and sand (B) Brine and coal (C) Coke and caustic soda (D) None of these

Description : Commercial production of soda ash by Solvay process requires limestone, __________ as raw materials. (A) Coke and sand (B) Brine and coal (C) Coke and caustic soda (D) None of these

Last Answer : (B) Brine and coal

Road grade bitumen is produced from vacuum residue by its (A) Aeration (B) Pyrolysis (C) Hydrogenation (D) Steam reforming

Description : Road grade bitumen is produced from vacuum residue by its (A) Aeration (B) Pyrolysis (C) Hydrogenation (D) Steam reforming

Last Answer : (D) Steam reforming

Which of the following oil gasification processes is non-catalytic? (A) Semet-Solvay process (B) Segas process (C) Onia-Gegi process (D) Steam reforming of naphtha

Description : Which of the following oil gasification processes is non-catalytic? (A) Semet-Solvay process (B) Segas process (C) Onia-Gegi process (D) Steam reforming of naphtha

Last Answer : (A) Semet-Solvay process

Catalyst used in steam reforming of naphtha is (A) Bauxite (B) Cobalt (C) Nickel oxide on alumina support (D) Chromium

Description : Catalyst used in steam reforming of naphtha is (A) Bauxite (B) Cobalt (C) Nickel oxide on alumina support (D) Chromium

Last Answer : (C) Nickel oxide on alumina support

Catalyst used in steam reforming of naphtha is (A) Nickel (B) Platinum (C) Silica gel (D) Rhodium

Description : Catalyst used in steam reforming of naphtha is (A) Nickel (B) Platinum (C) Silica gel (D) Rhodium

Last Answer : (A) Nickel

Which of the following is not endothermic in nature? (A) Combustion of sulphur (B) Gasification of carbon (C) Thermal cracking of fuel oil (D) Steam reforming of naphtha

Description : Which of the following is not endothermic in nature? (A) Combustion of sulphur (B) Gasification of carbon (C) Thermal cracking of fuel oil (D) Steam reforming of naphtha

Last Answer : (A) Combustion of sulphur

Conversion of CO to CO2 by steam in presence of a catalyst is called (A) Steam reforming (B) Shift conversion (C) Steam gasification (D) None of these

Description : Conversion of CO to CO2 by steam in presence of a catalyst is called (A) Steam reforming (B) Shift conversion (C) Steam gasification (D) None of these

Last Answer : (B) Shift conversion

Hydrogen gas is not produced commercially (for nitrogenous fertiliser manufacture) by (A) Iron-steam reaction (B) Electrolysis of water (C) Steam reforming of naphtha (D) Its cryogenic separation from coke oven gas

Description : Hydrogen gas is not produced commercially (for nitrogenous fertiliser manufacture) by (A) Iron-steam reaction (B) Electrolysis of water (C) Steam reforming of naphtha (D) Its cryogenic separation from coke oven gas

Last Answer : (A) Iron-steam reaction

Which of the following is the costliest source of getting hydrogen on commercial scale for the manufacture of nitrogenous fertiliser? (A) Coal gasification (B) Steam reforming of naphtha (C) Electrolysis of water (D) Coke oven gas

Description : Which of the following is the costliest source of getting hydrogen on commercial scale for the manufacture of nitrogenous fertiliser? (A) Coal gasification (B) Steam reforming of naphtha (C) Electrolysis of water (D) Coke oven gas

Last Answer : (C) Electrolysis of water

State the raw materials for manufacturing of ammonia. Write the balanced chemical reaction also.

Description : State the raw materials for manufacturing of ammonia. Write the balanced chemical reaction also. 

Last Answer : Ammonia Raw Material Synthesis gas as a source of hydrogen Air as source of nitrogen Reaction : N2+3H2 =2NH3

Low pressure Zeigler process for the manufacture of polythene uses a catalyst which is (A) Ni (B) V2O5 (C) Fe (D) Aluminium triethyl combined with titanium tetrachloride

Description : Low pressure Zeigler process for the manufacture of polythene uses a catalyst which is (A) Ni (B) V2O5 (C) Fe (D) Aluminium triethyl combined with titanium tetrachloride

Last Answer : (D) Aluminium triethyl combined with titanium tetrachloride

Transformer cores are normally made from (A) Soft ferrites (B) High purity iron (C) Grain oriented Fe-Si alloy (D) Al-Ni-Co alloy

Description : Transformer cores are normally made from (A) Soft ferrites (B) High purity iron (C) Grain oriented Fe-Si alloy (D) Al-Ni-Co alloy

Last Answer : (C) Grain oriented Fe-Si alloy

Maraging steels derive their strength from the following mechanism: (A) A fine, highly dislocated and strong martensite (B) Fine dispersions of inter-metallic of Fe, Ni, Ti etc (C) Fine dispersions of alloy carbides in a ferrite matrix (D) Fine dispersions of Fe3 C nucleated on dislocations in austenite

Description : Maraging steels derive their strength from the following mechanism: (A) A fine, highly dislocated and strong martensite (B) Fine dispersions of inter-metallic of Fe, Ni, Ti etc (C) Fine ... alloy carbides in a ferrite matrix (D) Fine dispersions of Fe3 C nucleated on dislocations in austenite

Last Answer : Option A

Co-efficient of thermal expansion of glass is decreased by the addition of __________ during its manufacture. (A) CaO (B) MnO2 (C) ZnO (D) FeS

Description : Co-efficient of thermal expansion of glass is decreased by the addition of __________ during its manufacture. (A) CaO (B) MnO2 (C) ZnO (D) FeS

Last Answer : (C) ZnO

Which of the following is not a commercially used feed-stock for the production of ammonia synthesis gas? (A) Water (B) Naphtha (C) Tar (D) Coal/coke oven gas

Description : Which of the following is not a commercially used feed-stock for the production of ammonia synthesis gas? (A) Water (B) Naphtha (C) Tar (D) Coal/coke oven gas

Last Answer : (C) Tar

Amongst `[TiE_(6)]^(2-), [CoF_(6)]^(3-), Cu_(2)Cl_(2)` and `[NiCl_(4)]^(2-)` [Atomic no. `Ti = 22, Co = 27, Cu = 29, Ni = 28`] the colourless species

Description : Amongst `[TiE_(6)]^(2-), [CoF_(6)]^(3-), Cu_(2)Cl_(2)` and `[NiCl_(4)]^(2-)` [Atomic no. `Ti = 22, Co = 27, Cu = 29, Ni = 28`] the colourless species

Last Answer : Amongst `[TiE_(6)]^(2-), [CoF_(6)]^(3-), Cu_(2)Cl_(2)` and `[NiCl_(4)]^(2-)` [Atomic no. `Ti = 22, ... (2)Cl_(2)` D. `TiF_(6)^(2-) and Cu_(2)Cl_(2)`

The metal that is used as a catalyst in the hydrogenation of oils is (a) Ni (b) Pb (c) Cu (d) Pt

Description : The metal that is used as a catalyst in the hydrogenation of oils is (a) Ni (b) Pb (c) Cu (d) Pt

Last Answer : Ans:(a)