Diaphragm electrolytic cell as compared to mercury electrolytic cell (A) Produces 70% NaOH solution (B) Requires less specific power consumption for the production of chlorine (C) Requires lesser investment for similar capacity (D) All (A), (B) and (C)

Diaphragm electrolytic cell as compared to mercury electrolytic cell
(A) Produces 70% NaOH solution
(B) Requires less specific power consumption for the production of chlorine
(C) Requires lesser investment for similar capacity
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(C) Requires lesser investment for similar capacity
by

Related questions

Mercury electrolytic cells are preferred over diaphragm electrolytic cell (for production of caustic soda), as it (A) Has larger production capacity per unit cell (B) Consumes less power per ton of Cl2 produced (C) Produces high purity (70%) caustic soda directly (D) All (A), (B) and (C)

Description : Mercury electrolytic cells are preferred over diaphragm electrolytic cell (for production of caustic soda), as it (A) Has larger production capacity per unit cell (B) Consumes less power per ton of Cl2 produced (C) Produces high purity (70%) caustic soda directly (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Mercury electrolytic cell produces 50-70% NaOH solution. Its operating temperature is __________ °C. (A) 25 (B) 60-70 (C) 150-200 (D) 250-300

Description : Mercury electrolytic cell produces 50-70% NaOH solution. Its operating temperature is __________ °C. (A) 25 (B) 60-70 (C) 150-200 (D) 250-300

Last Answer : (B) 60-70

Mercury cells for caustic soda manufacture, compared to diaphragm cells (A) Require lower initial investment (B) Require more power (C) Produce lower concentration NaOH (D) None of these

Description : Mercury cells for caustic soda manufacture, compared to diaphragm cells (A) Require lower initial investment (B) Require more power (C) Produce lower concentration NaOH (D) None of these

Last Answer : (D) None of these

Concentration of NaOH solution produced by diaphragm electrolytic cell is about __________ percent. (A) 10 (B) 25 (C) 50 (D) 98

Description : Concentration of NaOH solution produced by diaphragm electrolytic cell is about __________ percent. (A) 10 (B) 25 (C) 50 (D) 98

Last Answer : (A) 10

Concentration of NaOH solution produced by mercury electrolytic cell is about __________ percent. (A) 10 (B) 25 (C) 50 (D) 98

Description : Concentration of NaOH solution produced by mercury electrolytic cell is about __________ percent. (A) 10 (B) 25 (C) 50 (D) 98

Last Answer : (C) 50

Chlorine gas is produced by the electrolysis of brine (NaCl solution with solid NaCl make up) in mercury electrolytic cell. Which of the following is the anodic reaction? (A) Oxidation of Na + ions (B) Oxidation of Cl - ions (C) Reduction of Na + ions (D) Reduction of Cl - ions

Description : Chlorine gas is produced by the electrolysis of brine (NaCl solution with solid NaCl make up) in mercury electrolytic cell. Which of the following is the anodic reaction? (A) Oxidation of Na + ions (B) Oxidation of Cl - ions (C) Reduction of Na + ions (D) Reduction of Cl - ions

Last Answer : (B) Oxidation of Cl - ions

Which of the following processes does not produce Cl2 as a co-product during the manufacture of caustic soda? (A) Diaphragm electrolytic cell process (B) Mercury electrolytic cell process (C) Lime-soda process (D) None of these

Description : Which of the following processes does not produce Cl2 as a co-product during the manufacture of caustic soda? (A) Diaphragm electrolytic cell process (B) Mercury electrolytic cell process (C) Lime-soda process (D) None of these

Last Answer : (C) Lime-soda process

Which of the following is the most adverse factor challenging the choice of mercury electrolytic cell process for the production of caustic soda? (A) High cost of mercury (B) High specific gravity of mercury (C) Non-availability of high purity mercury (D) Pollution of water stream by mercury

Description : Which of the following is the most adverse factor challenging the choice of mercury electrolytic cell process for the production of caustic soda? (A) High cost of mercury (B) High specific gravity of mercury (C) Non-availability of high purity mercury (D) Pollution of water stream by mercury

Last Answer : (D) Pollution of water stream by mercury

The specific power consumption of non lubricated compressor compared to lubricated type is ____ a) Lesser b) Same c) Higher d) None

Description : The specific power consumption of non lubricated compressor compared to lubricated type is ____ a) Lesser b) Same c) Higher d) None 

Last Answer : c) Higher

What products do we get on electrolysis of saturated brine using steel cathode and graphite anode in an electrolytic cell? (A) Cl2 & Na (B) Cl2 & H2 (C) O2 & H2 (D) Cl2 , H2 & NaOH solution

Description : What products do we get on electrolysis of saturated brine using steel cathode and graphite anode in an electrolytic cell? (A) Cl2 & Na (B) Cl2 & H2 (C) O2 & H2 (D) Cl2 , H2 & NaOH solution

Last Answer : (D) Cl2 , H2 & NaOH solution

The electrolytic solution used in a hydrogen-oxygen fuel cell is ____________ a) 75% KOH solution b) 25% KOH solution c) 75% NaOH solution d) 25% NaOH solution

Description : The electrolytic solution used in a hydrogen-oxygen fuel cell is ____________ a) 75% KOH solution b) 25% KOH solution c) 75% NaOH solution d) 25% NaOH solution

Last Answer : b) 25% KOH solution

In the manufacture of H3 PO4 (ortho); strong H2 SO4 leaching wet process as compared to electric furnace process (A) Uses lower grade phosphate rock (B) Requires lower capital investment in the plant(C) Produces lower purity acid(D) Is very costly

Description : In the manufacture of H3 PO4 (ortho); strong H2 SO4 leaching wet process as compared to electric furnace process (A) Uses lower grade phosphate rock (B) Requires lower capital investment in the plant (C) Produces lower purity acid (D) Is very costly

Last Answer : (C) Produces lower purity acid

In closed circuit grinding as compared to open circuit grinding, the (A) Specific surface of product is more (B) Product has lesser size uniformity (C) Production rate at a given limiting size is lower (D) Operation is economical

Description : In closed circuit grinding as compared to open circuit grinding, the (A) Specific surface of product is more (B) Product has lesser size uniformity (C) Production rate at a given limiting size is lower (D) Operation is economical

Last Answer : (D) Operation is economical

Which of the following is the most suitable material of construction for evaporator & its tubes for concentrating NaOH solution to 70%? (A) Cast iron (B) Steel (C) Nickel (D) Karbate

Description : Which of the following is the most suitable material of construction for evaporator & its tubes for concentrating NaOH solution to 70%? (A) Cast iron (B) Steel (C) Nickel (D) Karbate

Last Answer : (C) Nickel

Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Description : Gyratory crushers compared to the reciprocating jaw crushers (A) Have greater capacity per unit of discharge area (B) Crush intermittently (C) Are less suitable for coarse materials (D) Have less steady power consumption

Last Answer : (A) Have greater capacity per unit of discharge area

A coal having high ratio of volatile matter to fixed carbon as compared to a coal having low ratio of volatile matter to fixed carbon (A) Is less liable to spontaneous combustion on storage (B) Is more difficult to ignite and produces a shorter flame (C) Requires smaller combustion space and less secondary air (D) None of these

Description : A coal having high ratio of volatile matter to fixed carbon as compared to a coal having low ratio of volatile matter to fixed carbon (A) Is less liable to spontaneous combustion on storage (B) ... a shorter flame (C) Requires smaller combustion space and less secondary air (D) None of these

Last Answer : (D) None of these

Wet grinding in a revolving mill __________ as compared to dry grinding. (A) Gives less wear on chamber walls (B) Requires more energy (C) Increases capacity (D) Complicates handling of the product

Description : Wet grinding in a revolving mill __________ as compared to dry grinding. (A) Gives less wear on chamber walls (B) Requires more energy (C) Increases capacity (D) Complicates handling of the product

Last Answer : (C) Increases capacity

In case of a revolving mill, wet grinding compared to dry grinding (A) Requires more energy (B) Has less capacity (C) Complicates handling & classification of the product (D) None of these

Description : In case of a revolving mill, wet grinding compared to dry grinding (A) Requires more energy (B) Has less capacity (C) Complicates handling & classification of the product (D) None of these

Last Answer : (D) None of these

A solution containing `Na_(2)CO_(3)` and `NaOH` requires `300 ml` of `0.1 N HCl` using phenolphthalein as an indicator. Methyl orange is then added to

Description : A solution containing `Na_(2)CO_(3)` and `NaOH` requires `300 ml` of `0.1 N HCl` using phenolphthalein as an indicator. Methyl orange is then added to

Last Answer : A solution containing `Na_(2)CO_(3)` and `NaOH` requires `300 ml` of `0.1 N HCl` using phenolphthalein ... solution is `(NaOH=40, Na_(2)CO_(3)=106)`

The specific fuel consumption of a petrol engine compared to diesel engine of same H.P is A. same B.more C. less D. unpredictable

Description : The specific fuel consumption of a petrol engine compared to diesel engine of same H.P is A. same B.more C. less D. unpredictable

Last Answer : ANSWER : B

Beehive coke oven (A) Facilitates by-products recovery (B) Takes 2-3 days for coking of coal but requires no external fuel for heating (C) Gives larger yield of coke (around 85%) as compared to by-product ovens (D) Produces coke with very poor strength

Description : Beehive coke oven (A) Facilitates by-products recovery (B) Takes 2-3 days for coking of coal but requires no external fuel for heating (C) Gives larger yield of coke (around 85%) as compared to by-product ovens (D) Produces coke with very poor strength

Last Answer : (B) Takes 2-3 days for coking of coal but requires no external fuel for heating

Industrial production of chloroform requires acetone and (A) Phosgene (B) Calcium hypochlorite (C) Chlorine (D) Ammonium chloride

Description : Industrial production of chloroform requires acetone and (A) Phosgene (B) Calcium hypochlorite (C) Chlorine (D) Ammonium chloride

Last Answer : (B) Calcium hypochlorite

Consider the following statements: (a) Revised simplex method requires lesser computations than the simplex method. (b) Revised simplex method automatically generates the inverse of the current basis matrix. (c) Less number of entries are needed in each table of revised simplex method than usual simplex method. Which of these statements are correct? (A) (a) and (b) only (B) (a) and (c) only (C) (b) and (c) only (D) (a), (b) and (c)

Description : Consider the following statements: (a) Revised simplex method requires lesser computations than the simplex method. (b) Revised simplex method automatically generates the inverse of the current basis matrix. (c) Less number of entries are needed ... c) only (C) (b) and (c) only (D) (a), (b) and (c)

Last Answer : (D) (a), (b) and (c)

The following graph represents the installed capacity for cement production (in tonnes) and the actual production (in tonnes) of nine cement plants of a cement company. Capacity utilization of a plant is defined as ratio of actual production of cement to installed capacity. A plant with installed capacity of at least 200 tonnes is called a large plant and a plant with lesser capacity is called a small plant. The difference between total production of large plants and small plants, in tonnes is _____

Description : The following graph represents the installed capacity for cement production (in tonnes) and the actual production (in tonnes) of nine cement plants of a cement company. Capacity utilization of a plant ... difference between total production of large plants and small plants, in tonnes is _____

Last Answer : Correct answer is 120.

If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Description : If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Last Answer : Ans :c

A thermal nuclear reactor compared to a fast breeder reactor (A) Uses slower neutrons for fission (B) Uses faster neutrons for fission (C) Gives higher power density (D) Requires less fuel to run at the same power level

Description : A thermal nuclear reactor compared to a fast breeder reactor (A) Uses slower neutrons for fission (B) Uses faster neutrons for fission (C) Gives higher power density (D) Requires less fuel to run at the same power level

Last Answer : (A) Uses slower neutrons for fission

Which of the following can be purified by the electrolytic method? (a) Sodium (Na) (b) Copper (Cu) (c) Boron (B) (d) Chlorine (C12)

Description : Which of the following can be purified by the electrolytic method? (a) Sodium (Na) (b) Copper (Cu) (c) Boron (B) (d) Chlorine (C12)

Last Answer : Ans:129

In a roll crusher, the specific power consumption and the production rate is affected by the (A) Reduction ratio (B) Differential roll speed (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In a roll crusher, the specific power consumption and the production rate is affected by the (A) Reduction ratio (B) Differential roll speed (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Maintain 850 OC for 1 hour (soaking time).  Cool the material to 60 OC in 4 hours. a) Calculate the efficiency of the furnace, if the specific heat of steel is 0.12 kcal/kgOC and fuel oil consumption per batch is 1400 litres.  GCV of fuel oil - 10200 kcal/kg,  Cost of fuel oil - Rs. 46,000/kL,  Sp. gr. of fuel oil - 0.92. b) Due to high cost of oil, the plant management decides to convert to a lower operating cost LPG fired furnace lined on the inside with ceramic fibre insulation and with an operating efficiency of 80%, for same requirement. The investment towards installation of the new furnace is Rs. 50 lakhs. Calculate the Return on Investment, if the plant operates two batches per day and 250 days in a year.  Cost of LPG - Rs. 75/kg,  GCV of LPG - 12500 kcal/kg.

Description : In a heat treatment shop, steel components are heat-treated in batches of 80 Tons. The  heat treatment cycle is as follows;  Increase temperature from 30 OC to 850 OC in 3 hours.  ... efficiency of 80%, for same requirement. The investment towards installation of  the new furnace is Rs. 50

Last Answer : Quantity of steel treated per batch - 80 Tons a. Efficiency of Furnace: Useful heat supplied to steel - 80000 x 0.12 x (850 - 30)   = 7872000 kcal/batch .1 mark Total heat ... = Rs. 64400/batch Efficiency of new LPG furnace - 80% Heat supplied in new LPG furnace - 7872000/0.8

Pick out the wrong statement about coating/electroplating of metals. (A) Phosphate coating is used as an excellent base for paints & enamels (B) Phosphate coating is less corrosion resistant than chromate coating (C) The base metal to be electroplated is normally made the cathode of the electrolytic cell and coating metal is made the anode (D) Calorising is the process of coating steel with chromium

Description : Pick out the wrong statement about coating/electroplating of metals. (A) Phosphate coating is used as an excellent base for paints & enamels (B) Phosphate coating is less corrosion resistant than ... coating metal is made the anode (D) Calorising is the process of coating steel with chromium

Last Answer : (D) Calorising is the process of coating steel with chromium

Steel sheets used in the production of furnitures is an example of (1) an intermediate good (2) a final good (3) an investment good (4) a consumption good

Description : Steel sheets used in the production of furnitures is an example of (1) an intermediate good (2) a final good (3) an investment good (4) a consumption good

Last Answer : (1) an intermediate good Explanation: Intermediate goods are semifinished products are goods that are used as inputs in the production of oilier goods including final goods. It comprises material or ... , intermediate goods either become part of the final product, or are changed beyond recognition.

What is the term in economics for the consumption of fixed capital? a) Investment b) Value added c) Production flow d) Depreciation

Description : What is the term in economics for the consumption of fixed capital? a) Investment b) Value added c) Production flow d) Depreciation

Last Answer : d) Depreciation

Steel sheets used in the production of furnitures is an example of (1) an intermediate good (2) a final good (3) an investment good (4) a consumption good

Description : Steel sheets used in the production of furnitures is an example of (1) an intermediate good (2) a final good (3) an investment good (4) a consumption good

Last Answer : an intermediate good

Pick out the wrong statement (A) Low ozone layer thickness in polar regions is due to cold climatic conditions (B) Amount of unburnt hydrocarbons emitted by two stroke petrol engine is more as compared to that emitted by a four stroke engine (C) Carbon monoxide present in the two stroke petrol engine exhaust is much less as compared to that emitted from a four stroke engine (D) Mercury as a pollutant can enter the blood stream & the digestive system/ lungs and is responsible for causing Minamata disease

Description : Pick out the wrong statement (A) Low ozone layer thickness in polar regions is due to cold climatic conditions (B) Amount of unburnt hydrocarbons emitted by two stroke petrol engine is more ... can enter the blood stream & the digestive system/ lungs and is responsible for causing Minamata disease

Last Answer : (D) Mercury as a pollutant can enter the blood stream & the digestive system/ lungs and is responsible for causing Minamata disease

When a fluid flows over a solid surface, the (A) Velocity is uniform at any cross-section (B) Velocity gradient is zero at the solid surface (C) Resistance between the surface & the fluid is lesser as compared to that between the fluid layers themselves (D) Velocity is not zero at the solid surface

Description : When a fluid flows over a solid surface, the (A) Velocity is uniform at any cross-section (B) Velocity gradient is zero at the solid surface (C) Resistance between the surface & the fluid is lesser as compared to that between the fluid layers themselves (D) Velocity is not zero at the solid surface

Last Answer : (B) Velocity gradient is zero at the solid surface

Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW

Description : Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW then annual energy production is  (1) 122.8 GWh (2) 198.55 GWh (3) 128.2 GWh (4) 188.82 GWh

Last Answer : Power station having Load factor = 70%, capacity factor = 50%, used factor = 60%, maximum demand = 20MW then annual energy production is 122.8 GWh

Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)

Description : Choke crushing (in case of a Jaw crusher) compared to free crushing (A) Results in increased capacity (B) Consumes less power (C) Consumes more power (D) Both (A) and (C)

Last Answer : (C) Consumes more power

Capacity & power requirement for an air compressor working at high altitude compared to sea-level will be (A) More (B) Less (C) Same (D) Either more or less; depends on the climatic conditions

Description : Capacity & power requirement for an air compressor working at high altitude compared to sea-level will be (A) More (B) Less (C) Same (D) Either more or less; depends on the climatic conditions

Last Answer : (B) Less

The reactions of `CI_(2)` gas with cold-dilute and hot-concentrated NaOH in water give sodium salts of two different oxioacids of chlorine, P and Q, r

Description : The reactions of `CI_(2)` gas with cold-dilute and hot-concentrated NaOH in water give sodium salts of two different oxioacids of chlorine, P and Q, r

Last Answer : The reactions of `CI_(2)` gas with cold-dilute and hot-concentrated NaOH in water give sodium salts of ... `H_3PO_2` D. `SOCl_2 , PCl_5` and `H_3PO_5`

The reactions of `CI_(2)` gas with cold-dilute and hot-concentrated NaOH in water give sodium salts of two different oxioacids of chlorine, P and Q, r

Description : The reactions of `CI_(2)` gas with cold-dilute and hot-concentrated NaOH in water give sodium salts of two different oxioacids of chlorine, P and Q, r

Last Answer : The reactions of `CI_(2)` gas with cold-dilute and hot-concentrated NaOH in water give ... porchloric acids D. (D) chloric and hypochlorus acids

An oil fired boiler is retrofitted to fire coconut shell chips. Boiler thermal efficiency drops from 82% to 70%. What will be the percentage change in energy consumption to generate the same output a) 12% increase b) 14.6% increase c) 17.1% decrease d) 17.1% increase

Description : An oil fired boiler is retrofitted to fire coconut shell chips. Boiler thermal efficiency drops from 82% to 70%. What will be the percentage change in energy consumption to generate the same output a) 12% increase b) 14.6% increase c) 17.1% decrease d) 17.1% increase

Last Answer : d) 17.1% increase

A concentric double pipe heat exchanger as compared to the shell and tube heat exchanger for the same heat load requires (A) Less heating surface (B) More space (C) Lower maintenance cost (D) None of these

Description : A concentric double pipe heat exchanger as compared to the shell and tube heat exchanger for the same heat load requires (A) Less heating surface (B) More space (C) Lower maintenance cost (D) None of these

Last Answer : (B) More space

Asseration: The thermal stability of hydrides of oxygen family decrease with molecular weight. Reason: The decomposition of `M-H` bond requires lesser

Description : Asseration: The thermal stability of hydrides of oxygen family decrease with molecular weight. Reason: The decomposition of `M-H` bond requires lesser

Last Answer : Asseration: The thermal stability of hydrides of oxygen family decrease with molecular weight. Reason: The decomposition ... in `O-H` than `S-H`.

For the transfer of solution of thick slurry, the pump used is a __________ pump(A) Reciprocating(B) Gear(C) Diaphragm(D) Centrifugal.

Description : For the transfer of solution of thick slurry, the pump used is a __________ pump. (A) Reciprocating (B) Gear (C) Diaphragm (D) Centrifugal

Last Answer : (C) Diaphragm

Solvay process as compared to dual process (i.e. modified Solvay process). (A) Can use low grade brine (B) Has less corrosion problems (C) Involves higher investment in NH3 recovery units than that for crystallisation units for NH4Cl(D) Both (B) and (C)

Description : Solvay process as compared to dual process (i.e. modified Solvay process). (A) Can use low grade brine (B) Has less corrosion problems (C) Involves higher investment in NH3 recovery units than that for crystallisation units for NH4Cl (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year showing the cost at that time relative to a certain base year (C) Turnover ratio of a chemical plant is the ratio of gross annual sales to the fixed capital investment (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Description : Pick out the wrong statement. (A) Longer tubes are less expensive per unit heat transfer area as compared to shorter tubes (B) A cost index is merely a number for a given year ... butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

Last Answer : (D) Plates with butt welded joints are less expensive compared to lap welded joints, because squaring of plates is not necessary

High temperature carbonisation of coal produces (A) Inferior coke compared to low temperature carbonisation (B) Less of gases compared to liquid products (C) Large quantity of tar compared to low temperature carbonisation (D) None of these

Description : High temperature carbonisation of coal produces (A) Inferior coke compared to low temperature carbonisation (B) Less of gases compared to liquid products (C) Large quantity of tar compared to low temperature carbonisation (D) None of these

Last Answer : (D) None of these

Electric process as compared to wet process (for the manufacture of phosphoric acid) (A) Can use only high grade phosphate rock (B) Is used less frequently (C) Produces a valuable by-product called gypsum (D) Is weak acid process

Description : Electric process as compared to wet process (for the manufacture of phosphoric acid) (A) Can use only high grade phosphate rock (B) Is used less frequently (C) Produces a valuable by-product called gypsum (D) Is weak acid process

Last Answer : (B) Is used less frequently

High temperature carbonisation of coal produces (A) Inferior coke compared to low temperature carbonisation(B) Less of gases compared to liquid products(C) Larger quantity of tar compared to low temperature carbonisation(D) None of these

Description : High temperature carbonisation of coal produces (A) Inferior coke compared to low temperature carbonisation (B) Less of gases compared to liquid products (C) Larger quantity of tar compared to low temperature carbonisation (D) None of these

Last Answer : (D) None of these

The surface tension of mercury at normal temperature compared to that of water is (A) More (B) Less (C) Same (D) More or less depending on size of glass tube

Description : The surface tension of mercury at normal temperature compared to that of water is (A) More (B) Less (C) Same (D) More or less depending on size of glass tube

Last Answer : Answer: Option A