Yield of urea can be increased with excess ammonia and higher pressure & temperature, but because of __________ this is normally not done. (A) Increased biuret formation (B) High corrosion rate (C) Increased cost of equipment (D) All (A), (B) & (C)

Yield of urea can be increased with excess ammonia and higher pressure
& temperature, but because of __________ this is normally not done.
(A) Increased biuret formation
(B) High corrosion rate
(C) Increased cost of equipment
(D) All (A), (B) & (C)
by

1 Answer

Answer :

(D) All (A), (B) & (C)
by

Related questions

Lower temperature and large excess of ammonia in urea melt (A) Increases biuret formation (B) Decreases biuret formation (C) Is undesirable (D) Does not effect biuret formation

Description : Lower temperature and large excess of ammonia in urea melt (A) Increases biuret formation (B) Decreases biuret formation (C) Is undesirable (D) Does not effect biuret formation

Last Answer : (B) Decreases biuret formation

Pick out the correct statement. (A) Reaction of NH3 with HNO3 to produce (NH4 )2NO3 is endothermic (B) With increase in NH3 /CO2 ratio, urea yield decreases for a given temperature, pressure and total feed rate (C) Biuret (an intermediate during urea manufacture) is toxic to seeds and animals (D) Both (B) and (C)

Description : Pick out the correct statement. (A) Reaction of NH3 with HNO3 to produce (NH4 )2NO3 is endothermic (B) With increase in NH3 /CO2 ratio, urea yield decreases for a given temperature, pressure and total ... (an intermediate during urea manufacture) is toxic to seeds and animals (D) Both (B) and (C)

Last Answer : (B) With increase in NH3 /CO2 ratio, urea yield decreases for a given temperature, pressure and total feed rate

Describe the following points with respect to manufacturing of Urea. (i) Temperature (ii) Pressure (iii) Formation of Biuret

Description : Describe the following points with respect to manufacturing of Urea. (i) Temperature (ii) Pressure (iii) Formation of Biuret

Last Answer : Manufacturing of Urea w.r.t following points 1. Temperature: Urea production rate increases as temperature increases up to 180oC and then fall sharply. 2. Pressure: Urea production rate increases as pressure ... before sending to prilling tower. 2NH2 .CO.NH2 = NH2.CO.NH.CO.NH2 + NH

Biuret formation in urea is kept at minimum (< 1 %), because it is (A) Corrosive in nature (B) Toxic and harmful to some crops (C) Helpful in decomposition of urea (D) Explosive in nature

Description : Biuret formation in urea is kept at minimum (< 1 %), because it is (A) Corrosive in nature (B) Toxic and harmful to some crops (C) Helpful in decomposition of urea (D) Explosive in nature

Last Answer : (B) Toxic and harmful to some crops

The composition of fresh feed to the high temperature, high pressure urea autoclave is (A) Excess liquid ammonia and liquefied CO2 (B) Excess liquid ammonia and compressed CO2 gas (C) Liquid ammonia and excess compressed CO2 (D) Compressed ammonia gas and excess compressed CO2

Description : The composition of fresh feed to the high temperature, high pressure urea autoclave is (A) Excess liquid ammonia and liquefied CO2 (B) Excess liquid ammonia and compressed CO2 gas (C) Liquid ammonia and excess compressed CO2 (D) Compressed ammonia gas and excess compressed CO2

Last Answer : (B) Excess liquid ammonia and compressed CO2 gas

Dehydration of ammonium carbamate produces (A) Urea (B) Biuret (C) Ammonia water (D) None of these

Description : Dehydration of ammonium carbamate produces (A) Urea (B) Biuret (C) Ammonia water (D) None of these

Last Answer : (A) Urea

Prilling of urea should be accomplished (in a sprayer) just above the melting point of urea with minimum of retention time, otherwise it will result in (A) Low bulk density product (B) Biuret formation (C) Non-spherical prills (D) Substantially wet non-flowing and sticky product

Description : Prilling of urea should be accomplished (in a sprayer) just above the melting point of urea with minimum of retention time, otherwise it will result in (A) Low bulk density product (B) Biuret formation (C) Non-spherical prills (D) Substantially wet non-flowing and sticky product

Last Answer : (B) Biuret formation

In a gas-liquid shell and tube heat exchanger, the(A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure gases are corrosive in nature (C) Gases to be heated/cooled is normally routed through the shell side, because the corrosion caused by the cooling water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Description : In a gas-liquid shell and tube heat exchanger, the (A) Presence of a non-condensable gas decreases the condensing film co￾efficient (B) Gases under high pressure are routed through the tube side, because high pressure ... water or steam condensate remain localised to the tubes (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

__________ is the undesirable by-product produced in the manufacture of urea. (A) Ammonium carbonate (B) Biuret (C) Carbon dioxide (D) Ammonium carbamate

Description : __________ is the undesirable by-product produced in the manufacture of urea. (A) Ammonium carbonate (B) Biuret (C) Carbon dioxide (D) Ammonium carbamate

Last Answer : (B) Biuret

In low temperature carbonisation of coal as compared to high temperature carbonisation __________ produced is less. (A) Difference in gross & net calorific value of the coke oven gas (B) Free carbon content in tar (C) Yield percentage of coke (D) Yield of ammonia present in coke oven gas

Description : In low temperature carbonisation of coal as compared to high temperature carbonisation __________ produced is less. (A) Difference in gross & net calorific value of the coke oven gas (B) Free carbon content in tar (C) Yield percentage of coke (D) Yield of ammonia present in coke oven gas

Last Answer : (A) Difference in gross & net calorific value of the coke oven gas

With increases in pressure, the conversion of Ammonium carbamate into urea (A) Increases (B) Decreases (C) Remains unaltered (D) Can either increase or decrease depends on biuret content

Description : With increases in pressure, the conversion of Ammonium carbamate into urea (A) Increases (B) Decreases (C) Remains unaltered (D) Can either increase or decrease depends on biuret content

Last Answer : (A) Increases

During conversion of ammonium carbamate into urea, presence of large excess of water (A) Increases the yield of urea (B) Adversely affects the yield of urea (C) Reduces the evaporator load by diluting the urea solution (D) Does not affect the yield of urea

Description : During conversion of ammonium carbamate into urea, presence of large excess of water (A) Increases the yield of urea (B) Adversely affects the yield of urea (C) Reduces the evaporator load by diluting the urea solution (D) Does not affect the yield of urea

Last Answer : (B) Adversely affects the yield of urea

__________ is the process of coating the surface of steel with aluminium oxide, thereby imparting it increased resistance to corrosion & oxidation upto a temperature of 700°C. (A) Veneering (B) Galvanising (C) Electroplating (D) Calorising

Description : __________ is the process of coating the surface of steel with aluminium oxide, thereby imparting it increased resistance to corrosion & oxidation upto a temperature of 700°C. (A) Veneering (B) Galvanising (C) Electroplating (D) Calorising

Last Answer : (D) Calorising

In the manufacture of urea, the intermediate chemical formed is (A) Biuret (B) Ammonium carbamate (C) Ammonium carbonate (D) None of these

Description : In the manufacture of urea, the intermediate chemical formed is (A) Biuret (B) Ammonium carbamate (C) Ammonium carbonate (D) None of these

Last Answer : (B) Ammonium carbamat

Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250

Description : Metallic recuperators are not used for waste heat recovery, if the hot flue gas temperature is above __________ °C, because corrosion prevails at higher temperatures. (A) 350 (B) 750 (C) 1050 (D) 1250

Last Answer : (B) 750

Which of the following set of conditions is favourable for the maximum yield of ammonia by Haber's process? (A) High pressure, low reactants concentration, high temperature (B) High pressure, low reactants concentration, low temperature (C) High pressure, high reactants concentration, low temperature (D) Low pressure, high reactants concentration, low temperature

Description : Which of the following set of conditions is favourable for the maximum yield of ammonia by Haber's process? (A) High pressure, low reactants concentration, high temperature (B) High ... , high reactants concentration, low temperature (D) Low pressure, high reactants concentration, low temperature

Last Answer : (C) High pressure, high reactants concentration, low temperature

An increase in the NH3 /CO2 ratio in urea manufacture results in (A) Increased degree of conversion of CO2 to urea (B) Decreased degree of conversion of NH3 to urea (C) Decreased yield of urea (D) Decreased specific volume of molten mass

Description : An increase in the NH3 /CO2 ratio in urea manufacture results in (A) Increased degree of conversion of CO2 to urea (B) Decreased degree of conversion of NH3 to urea (C) Decreased yield of urea (D) Decreased specific volume of molten mass

Last Answer : (A) Increased degree of conversion of CO2 to urea

Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of light distillates (B) Suppress coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline

Description : Though increased pressure has a retarding effect on cracking reaction, yet in actual process, a positive pressure of 10-15 kgf/cm2 is maintained during cracking mainly to (A) Increase the yield of ... coke formation (C) Enhance the octane number of gasoline (D) Reduce gum content in gasoline

Last Answer : (B) Suppress coke formation

What happens when urea is treated with hydrazine? (a) Biuret is formed (b) Semicarbazide is formed(c) Carbon dioxide and nitrogen is formed(d) Acetamide is formed

Description : What happens when urea is treated with hydrazine? (a) Biuret is formed (b) Semicarbazide is formed (c) Carbon dioxide and nitrogen is formed (d) Acetamide is formed

Last Answer : Semicarbazide is formed

Which of the following is not a result of the excess of impurity in boiler-feed. a) Scale and sludge formation b) Decomposition c) Corrosion, priming and foaming d) Caustic embrittlement

Description : Which of the following is not a result of the excess of impurity in boiler-feed. a) Scale and sludge formation b) Decomposition c) Corrosion, priming and foaming d) Caustic embrittlement

Last Answer : b) Decomposition

For formation of urea which one of the following is required alongwith ammonia

Description : For formation of urea which one of the following is required alongwith ammonia

Last Answer : For formation of urea which one of the following is required alongwith ammonia A. Arginase, `CO_(2)` and `O_(2 ... D. Asparate, `CO_(2)` and `O_(2)`

Though kinetics of ammonia synthesis dictates the use of low temperature for high equilibrium conversion, yet it is kept moderately high (550°C), because at low temperature (A) Rate of reaction is very low (B) Very high pressure is required resulting in costly pressure vessel (C) Space velocity of gas is very low resulting in decreased conversion (D) None of these

Description : Though kinetics of ammonia synthesis dictates the use of low temperature for high equilibrium conversion, yet it is kept moderately high (550°C), because at low temperature (A) Rate of reaction is very low ... (C) Space velocity of gas is very low resulting in decreased conversion (D) None of these

Last Answer : (A) Rate of reaction is very low

In the ammonia synthesis reaction, N2 + 3H2 ⇌ 2NH3 + 22.4 kcal, the formation of NH3 will be favoured by (A) High temperature (B) Low pressure (C) Low temperature only (D) Both low temperature and high pressure

Description : In the ammonia synthesis reaction, N2 + 3H2 ⇌ 2NH3 + 22.4 kcal, the formation of NH3 will be favoured by (A) High temperature (B) Low pressure (C) Low temperature only (D) Both low temperature and high pressure

Last Answer : (D) Both low temperature and high pressure

Higher plants take up nitrogen as (a) Nitrites only (b) Nitrates only (c) Nitrates and ammonia (d) Urea

Description : Higher plants take up nitrogen as (a) Nitrites only (b) Nitrates only (c) Nitrates and ammonia (d) Urea

Last Answer : Ans:(c)

In low temperature carbonisation (as compared to high temperature carbonisation) of coal (A) Ammonia yield is more (B) Aliphatic tar is produced (C) Free carbon in tar is more (D) All (A), (B) and (C

Description : In low temperature carbonisation (as compared to high temperature carbonisation) of coal (A) Ammonia yield is more (B) Aliphatic tar is produced (C) Free carbon in tar is more (D) All (A), (B) and (C

Last Answer : (B) Aliphatic tar is produced

In high temperature carbonisation of coal compared to low temperature carbonisation (A) Yield of ammonia is less (B) Aromatic content of tar is low (C) H2 content in the coke oven gas is more (D) Calorific value of the coke oven gas is lower

Description : In high temperature carbonisation of coal compared to low temperature carbonisation (A) Yield of ammonia is less (B) Aromatic content of tar is low (C) H2 content in the coke oven gas is more (D) Calorific value of the coke oven gas is lower

Last Answer : (C) H2 content in the coke oven gas is more

Dehydration of ammonium carbamate to yield urea is a/an __________ reaction. (A) Exothermic (B) Endothermic (C) Autocatalytic (D) Catalytic

Description : Dehydration of ammonium carbamate to yield urea is a/an __________ reaction. (A) Exothermic (B) Endothermic (C) Autocatalytic (D) Catalytic

Last Answer : (B) Endothermic

Pick out the wrong statement about coating/electroplating of metals. (A) Phosphate coating is used as an excellent base for paints & enamels (B) Phosphate coating is less corrosion resistant than chromate coating (C) The base metal to be electroplated is normally made the cathode of the electrolytic cell and coating metal is made the anode (D) Calorising is the process of coating steel with chromium

Description : Pick out the wrong statement about coating/electroplating of metals. (A) Phosphate coating is used as an excellent base for paints & enamels (B) Phosphate coating is less corrosion resistant than ... coating metal is made the anode (D) Calorising is the process of coating steel with chromium

Last Answer : (D) Calorising is the process of coating steel with chromium

Conversion of ammonia to urea is done by `…......................` Cycl -

Description : Conversion of ammonia to urea is done by `…......................` Cycl -

Last Answer : Conversion of ammonia to urea is done by `…......................` Cycl - A. Ornithine cycle B. Arginine cycle C. Fumaric cycle D. Citrulline cycle

Conversion of ammonia to urea is done by `…......................` Cycl -

Description : Conversion of ammonia to urea is done by `…......................` Cycl -

Last Answer : Conversion of ammonia to urea is done by `…......................` Cycl - A. Omithine cycle B. Arginine cycle C. Fumaric cycle D. Citrulline cycle

Conversion of ammonia to urea is done by (a) ornithine cycle (b) arginine cycle (c) fumaric cycle (d) citrulline cycle.

Description : Conversion of ammonia to urea is done by (a) ornithine cycle (b) arginine cycle (c) fumaric cycle (d) citrulline cycle.

Last Answer : (a) ornithine cycle

In the gaseous phase ammonia formation reaction (N2 + 3H2 ⇌ 2NH3 ), the value of the equilibrium constant depends on the (A) Total pressure of the system (B) Volume of the reactor (C) Temperature (D) Initial concentration of N2 and H2

Description : In the gaseous phase ammonia formation reaction (N2 + 3H2 ⇌ 2NH3 ), the value of the equilibrium constant depends on the (A) Total pressure of the system (B) Volume of the reactor (C) Temperature (D) Initial concentration of N2 and H2

Last Answer : (C) Temperature

In a shell and tube type heat exchanger, the floating tube bundle heat arrangement is used (A) In low range of temperature differences (B) In high range of temperature differences (C) Because of its low cost (D) To prevent corrosion of the tube bundles

Description : In a shell and tube type heat exchanger, the floating tube bundle heat arrangement is used (A) In low range of temperature differences (B) In high range of temperature differences (C) Because of its low cost (D) To prevent corrosion of the tube bundles

Last Answer : (B) In high range of temperature differences

Indirect contact heat exchangers are preferred over direct contact heat exchangers, because (A) Heat transfer co-efficient are high (B) There is no risk of contamination (C) There is no mist formation (D) Cost of equipment is lower

Description : Indirect contact heat exchangers are preferred over direct contact heat exchangers, because (A) Heat transfer co-efficient are high (B) There is no risk of contamination (C) There is no mist formation (D) Cost of equipment is lower

Last Answer : (B) There is no risk of contamination

In cooling tower ,higher temperature __________ corrosion potential • Decrease • Increase • Temperature has no effect on corrosion

Description : In cooling tower ,higher temperature __________ corrosion potential • Decrease • Increase • Temperature has no effect on corrosion

Last Answer : Increase

Choose the correct statement regarding thermal cracking. (A) Moderate changes in operating temperature does not change the depth of cracking (B) Increased residence time results in the decreased severity of cracking (C) At low pressure, the yield of lighter hydrocarbons are more (D) Greater depth of cracking gives lower octane number gasoline

Description : Choose the correct statement regarding thermal cracking. (A) Moderate changes in operating temperature does not change the depth of cracking (B) Increased residence time results in the decreased ... of lighter hydrocarbons are more (D) Greater depth of cracking gives lower octane number gasoline

Last Answer : (D) Greater depth of cracking gives lower octane number gasoline

During manufacture of H2SO4 , the oxidation of SO2 to SO3 by oxygen is an endothermic reaction. The yield of SO3 will be maximised, if the (A) Temperature is increased (B) Pressure is reduced (C) Temperature is increased and pressure is reduced (D) Temperature is reduced and pressure is increased

Description : During manufacture of H2SO4 , the oxidation of SO2 to SO3 by oxygen is an endothermic reaction. The yield of SO3 will be maximised, if the (A) Temperature is increased (B) Pressure is reduced (C) Temperature is increased and pressure is reduced (D) Temperature is reduced and pressure is increased

Last Answer : (D) Temperature is reduced and pressure is increased

Ceramic nuclear metals compared to solid nuclear metals have (A) Higher melting points (B) Low strength at high temperature (C) More chances of radiation damage (D) Poorer corrosion resistance

Description : Ceramic nuclear metals compared to solid nuclear metals have (A) Higher melting points (B) Low strength at high temperature (C) More chances of radiation damage (D) Poorer corrosion resistance

Last Answer : (A) Higher melting points

Corrosion rate cannot be lowered by reducing the __________ of the corroding medium. (A) Concentration (B) Velocity (C) Temperature (D) None of these

Description : Corrosion rate cannot be lowered by reducing the __________ of the corroding medium. (A) Concentration (B) Velocity (C) Temperature (D) None of these

Last Answer : (A) Concentration

Use of catalyst is a must in the ammonia manufacture, because the reaction is reversible as well as the heat of dissociation of N2 & H2 is high. The presence of promoter along with the catalyst helps in __________ of the catalyst. (A) Stabilisation (B) Increasing the effectiveness (C) Improving the strength & heat resistance (D) All a, b & c

Description : Use of catalyst is a must in the ammonia manufacture, because the reaction is reversible as well as the heat of dissociation of N2 & H2 is high. The presence of promoter along with the catalyst helps in ... B) Increasing the effectiveness (C) Improving the strength & heat resistance (D) All a, b & c

Last Answer : (D) All a, b & c

Probability of cavitation occuring becomes very high, when the local __________ resulting in water bubbles formation, which on rupture cause cavitation (A) Pressure falls below the vapour pressure (B) Pressure becomes very high (C) Temperature becomes low (D) All 'a', 'b' & 'c'

Description : Probability of cavitation occuring becomes very high, when the local __________ resulting in water bubbles formation, which on rupture cause cavitation (A) Pressure falls below the vapour pressure (B) Pressure becomes very high (C) Temperature becomes low (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Description : Higher efficiency in the combustion of solid fuel cannot be achieved by (A) Proper fuel preparation (B) Keeping the flue gas exhaust temperature very high (C) Adopting efficient-fuel firing technique & equipment (D) Supplying correct quantity of combustion air

Last Answer : (B) Keeping the flue gas exhaust temperature very high

Tar yield in the low temperature and high temperature carbonisation of dry coal may be respectively __________ percent. (A) 3 & 10 (B) 10 & 3 (C) 10 & 20 (D) 15 & 8

Description : Tar yield in the low temperature and high temperature carbonisation of dry coal may be respectively __________ percent. (A) 3 & 10 (B) 10 & 3 (C) 10 & 20 (D) 15 & 8

Last Answer : (B) 10 & 3

The most prominent single cause of corrosion in boiler-tubes, drums, economisers and steam superheaters in a thermal power plant boiler is the (A) Water alkalinity & leakage (B) Hydrazine addition during feed water treatment (C) Release of non-condensable gas from water in the boiler (D) Scale formation

Description : The most prominent single cause of corrosion in boiler-tubes, drums, economisers and steam superheaters in a thermal power plant boiler is the (A) Water alkalinity & leakage (B) Hydrazine addition during ... treatment (C) Release of non-condensable gas from water in the boiler (D) Scale formation

Last Answer : (C) Release of non-condensable gas from water in the boiler

High copper amalgam lasts longer than low copper amalgam because of:** A. Increased compressive strength B. Increased corrosion resistance C. High creep D. Increased tensile strength E. Decreased setting expansion

Description : High copper amalgam lasts longer than low copper amalgam because of:**  A. Increased compressive strength  B. Increased corrosion resistance  C. High creep  D. Increased tensile strength  E. Decreased setting expansion 

Last Answer : A. Increased compressive strength 

Higher pressure in the reforming reactor (A) Increases coke formation (B) Increases the rate of reaction(C) Produces high octane number gasoline(D) None of these

Description : Higher pressure in the reforming reactor (A) Increases coke formation (B) Increases the rate of reaction (C) Produces high octane number gasoline (D) None of these

Last Answer : (D) None of these

Which of the following statements about respiratory acidosis are true? A. Compensation occurs by a shift of chloride out of the red blood cells. B. Renal compensation occurs rapidly. C. Retention of bicarbonate and increased ammonia formation are normal compensatory mechanisms. D. Narcotic administration is an unusual cause of respiratory acidosis. E. The ratio of bicarbonate to carbonic acid is less than 20:1.

Description : Which of the following statements about respiratory acidosis are true? A. Compensation occurs by a shift of chloride out of the red blood cells. B. Renal compensation occurs rapidly. C. Retention of ... of respiratory acidosis. E. The ratio of bicarbonate to carbonic acid is less than 20:1.

Last Answer : Answer: CE DISCUSSION: Renal compensation for acute hypoventilation is relatively slow. Depression of the respiratory center by morphine can lead to respiratory acidosis. Renal retention of bicarbonate, ... into red cells combine to increase the ratio of bicarbonate to carbonic acid to 20:1

Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Description : Combustion of pulverised coal compared to the lumpy coal (A) Provides better control of furnace temperature (B) Facilitates combustion with lower excess air (C) Provides higher thermal efficiency & flame temperature (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Exposure to SO2 containing chimney gases results in the (A) Reduction in strength of leather & cloth (B) Acceleration of corrosion rates of metals (C) Increased drying & hardening time of paints (D) All (A), (B) and (C)

Description : Exposure to SO2 containing chimney gases results in the (A) Reduction in strength of leather & cloth (B) Acceleration of corrosion rates of metals (C) Increased drying & hardening time of paints (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

What steps can be taken to avoid stress corrosion cracking (SCC) in steel vessels used for storing anhydrous ammonia?

Description : What steps can be taken to avoid stress corrosion cracking (SCC) in steel vessels used for storing anhydrous ammonia?

Last Answer : The U.S. National Board of Pressure Vessel Inspectors recommends the following in one of their classic articles: 1. Pressure vessels should be fully stress relieved or fabricated with heads that ... at least 0.2 percent water to inhibit SCC. Source: National Board of Pressure Vessel Inspectors