Pressure drag does not depend upon the(A) Roughness of surface of the body (B) Pressure of main flow only (C) Length of the body in flow direction (D) All (A), (B) and (C)

Pressure drag does not depend upon the
(A) Roughness of surface of the body
(B) Pressure of main flow only
(C) Length of the body in flow direction
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C)
by

Related questions

Friction factor for fluid flow in pipe does not depend upon the (A) Pipe length (B) Pipe roughness (C) Fluid density & viscosity (D) Mass flow rate of fluid

Description : Friction factor for fluid flow in pipe does not depend upon the (A) Pipe length (B) Pipe roughness (C) Fluid density & viscosity (D) Mass flow rate of fluid

Last Answer : A) Pipe length

Location of vena-contracta in an orificemeter does not depend upon the (A) Type of orifice (B) Density, viscosity & compressibility of the fluid (C) Ratio of pipe diameter to orifice diameter (D) Pipe roughness

Description : Location of vena-contracta in an orificemeter does not depend upon the (A) Type of orifice (B) Density, viscosity & compressibility of the fluid (C) Ratio of pipe diameter to orifice diameter (D) Pipe roughness

Last Answer : (A) Type of orifice

The friction factor for turbulent flow in a hydraulically smooth pipe (A) Depends only on Reynolds number (B) Does not depend on Reynolds number (C) Depends on the roughness (D) None of these

Description : The friction factor for turbulent flow in a hydraulically smooth pipe (A) Depends only on Reynolds number (B) Does not depend on Reynolds number (C) Depends on the roughness (D) None of these

Last Answer : (A) Depends only on Reynolds number

Drag force acting on a body does not depend upon the (A) Density of the fluid (B) Density of the body (C) Velocity of the body (D) Projected area of the body

Description : Drag force acting on a body does not depend upon the (A) Density of the fluid (B) Density of the body (C) Velocity of the body (D) Projected area of the body

Last Answer : (B) Density of the body

Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads (D) Fanning friction factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Description : Pick out the wrong statement: (A) Greater is the kinematic viscosity of the liquid, greater is the thickness of the boundary layer (B) Blowers develop a maximum pressure of 2 atmospheres ( ... factor in case of turbulent flow of liquids in pipe depends upon relative roughness & Reynolds number

Last Answer : (C) Friction losses in pipe fittings are generally expressed in terms of velocity heads

Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent) varies linearly as the radial distance (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Description : Pick out the wrong statement. (A) The form drag is dependent upon the occurrence of a wake (B) The shear stress at any given cross-section of a pipe for steady flow (either laminar or turbulent ... of viscosity (D) Existence of the boundary layer in fluid flow is because of viscosity of the fluid

Last Answer : (C) An ideal fluid is the one, which has negligible surface tension and obeys the Newton's law of viscosity

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Transition from laminar flow to turbulent flow is aided by the (A) Surface roughness and curvature (i.e. sharp corners) (B) Vibration (C) Pressure gradient and the compressibility of the flowing medium (D) All (A), (B) & (C)

Description : Transition from laminar flow to turbulent flow is aided by the (A) Surface roughness and curvature (i.e. sharp corners) (B) Vibration (C) Pressure gradient and the compressibility of the flowing medium (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Description : Transition from laminar flow to turbulent flow in fluid flow through a pipe does not depend upon the (A) Length of the pipe (B) Diameter of the pipe (C) Density of the fluid (D) Velocity of the fluid

Last Answer : (A) Length of the pipe

depends upon The Chezy’s constant C in the formula V = C A. Size of the sewer B. Shape of the sewer C. Roughness of sewer surface D. All the above

Description : depends upon The Chezy’s constant C in the formula V = C A. Size of the sewer B. Shape of the sewer C. Roughness of sewer surface D. All the above

Last Answer : ANS: D

The heat dissipated by from a surface depends upon its temperature and its characteristics like colour, roughness etc. (a) conduction (b) convection (c) radiation (d) any ofthe above

Description : The heat dissipated by from a surface depends upon its temperature and its characteristics like colour, roughness etc. (a) conduction (b) convection (c) radiation (d) any ofthe above

Last Answer : (c) radiation

Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, in the direction of flow of the liquid, is known as (A) Lift (B) Drag (C) Stagnation pressure (D) Bulk modulus

Description : Whenever a plate is held immersed at some angle with the direction of flow of the liquid, it is subjected to some pressure. The component of this pressure, in the direction of flow of the liquid, is known as (A) Lift (B) Drag (C) Stagnation pressure (D) Bulk modulus

Last Answer : Answer: Option B

In the complete turbulence zone (in rough pipes), the (A) Rough and smooth pipes have the same friction factor (B) Laminar film covers the roughness projections (C) Friction factor depends upon NRe only (D) Friction factor is independent of the relative roughness

Description : In the complete turbulence zone (in rough pipes), the (A) Rough and smooth pipes have the same friction factor (B) Laminar film covers the roughness projections (C) Friction factor depends upon NRe only (D) Friction factor is independent of the relative roughness

Last Answer : (D) Friction factor is independent of the relative roughness

Filtration rate does not depend upon the (A) Pressure drop & area of filtering surface (B) Resistance of the cake & the septum (C) Properties of the cake & the filtrate (D) None of these

Description : Filtration rate does not depend upon the (A) Pressure drop & area of filtering surface (B) Resistance of the cake & the septum (C) Properties of the cake & the filtrate (D) None of these

Last Answer : (D) None of these

Isothermal turbulent flow of a fluid results in decrease of its pressure, which depends on the (A) Wall roughness (B) Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Isothermal turbulent flow of a fluid results in decrease of its pressure, which depends on the (A) Wall roughness (B) Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The rate of emission of radiation by a body does not depend upon the (A) Wavelength of radiation (B) Surface temperature of the body (C) Nature of the surface (D) Shape and porosity of the body

Description : The rate of emission of radiation by a body does not depend upon the (A) Wavelength of radiation (B) Surface temperature of the body (C) Nature of the surface (D) Shape and porosity of the body

Last Answer : (D) Shape and porosity of the body

The rate of emission of radiation by a body does not depend upon the (A) Wavelength of radiation (B) Surface temperature of the body (C) Nature of the surface (D) Shape and porosity of the body

Description : The rate of emission of radiation by a body does not depend upon the (A) Wavelength of radiation (B) Surface temperature of the body (C) Nature of the surface (D) Shape and porosity of the body

Last Answer : (D) Shape and porosity of the body

Drag is defined as the force exerted by the (A) Fluid on the solid in a direction opposite to flow (B) Fluid on the solid in the direction of flow (C) Solid on the fluid (D) None of these

Description : Drag is defined as the force exerted by the (A) Fluid on the solid in a direction opposite to flow (B) Fluid on the solid in the direction of flow (C) Solid on the fluid (D) None of these

Last Answer : (B) Fluid on the solid in the direction of flow

In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said to have the same hydraulic roughness, when they have equal values of (A) Relative roughness (B) Absolute roughness (C) Friction co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Description : In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said ... co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Last Answer : (C) Friction co-efficient for flows at equal Reynold number

The time period of a simple pendulum does not depend upon the mass of the body suspended at the free end of the string. This statement is known as ___________ . (A) law of gravity (B) law of mass (C) law of isochronism (D) law of length

Description : The time period of a simple pendulum does not depend upon the mass of the body suspended at the free end of the string. This statement is known as ___________ . (A) law of gravity (B) law of mass (C) law of isochronism (D) law of length

Last Answer : (B) law of mass

The frictional resistance in laminar flow does not depend on the (A) Area of surface in contact (B) Flow velocity (C) Fluid temperature (D) Pressure of flow

Description : The frictional resistance in laminar flow does not depend on the (A) Area of surface in contact (B) Flow velocity (C) Fluid temperature (D) Pressure of flow

Last Answer : (A) Area of surface in contact

Cvfor an ideal gas (A) Does not depend upon temperature (B) Is independent of pressure only (C) Is independent of volume only (D) Is independent of both pressure and volume

Description : Cvfor an ideal gas (A) Does not depend upon temperature (B) Is independent of pressure only (C) Is independent of volume only (D) Is independent of both pressure and volume

Last Answer : (D) Is independent of both pressure and volume

The discharge co-efficient for an orifice meter does not depend upon the (A) Pipe length (B) Ratio of pipe diameter to orifice diameter (C) Type of orifice & the Reynolds number (D) Pipe diameter

Description : The discharge co-efficient for an orifice meter does not depend upon the (A) Pipe length (B) Ratio of pipe diameter to orifice diameter (C) Type of orifice & the Reynolds number (D) Pipe diameter

Last Answer : (A) Pipe length

Radiation heat transfer rates does not depend upon the (A) Type of absorbing surface (B) Distance between the heat source and the object receiving the heat (C) Surface area and temperature of the heat source (D) None of these

Description : Radiation heat transfer rates does not depend upon the (A) Type of absorbing surface (B) Distance between the heat source and the object receiving the heat (C) Surface area and temperature of the heat source (D) None of these

Last Answer : (D) None of these

Thermal conductivity of a material does not depend upon its (A) Mass (B) Volume (C) Surface area (D) All 'a', 'b' & 'c'

Description : Thermal conductivity of a material does not depend upon its (A) Mass (B) Volume (C) Surface area (D) All 'a', 'b' & 'c'

Last Answer : (D) All 'a', 'b' & 'c'

In turbulent flow, a rough pipe has the same friction factor as a smooth pipe (A) In the zone of complete turbulence (B) When the roughness projections are much smaller than the thickness of the laminar film (C) Everywhere in the transition zone (D) When the friction factor is independent of the Reynold's number

Description : In turbulent flow, a rough pipe has the same friction factor as a smooth pipe (A) In the zone of complete turbulence (B) When the roughness projections are much smaller than the thickness of ... ) Everywhere in the transition zone (D) When the friction factor is independent of the Reynold's number

Last Answer : (B) When the roughness projections are much smaller than the thickness of the laminar film

The losses in open channel flow generally vary as the (A) Inverse of the roughness (B) First power of the roughness (C) Square of the velocity (D) Inverse square of hydraulic radius

Description : The losses in open channel flow generally vary as the (A) Inverse of the roughness (B) First power of the roughness (C) Square of the velocity (D) Inverse square of hydraulic radius

Last Answer : (B) First power of the roughness

Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Fanning friction factor for laminar flow of fluid in a circular pipe is (A) Not a function of the roughness of pipe wall (B) Inversely proportional to Reynolds number (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Pick out the wrong statement. (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment (B) The emissivity of a surface increases with increase in surface roughness (C) The emissivity of a polished surface is quite low (D) The emissivity of a non-metallic surface decreases with increase in the temperature

Description : Pick out the wrong statement. (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment (B) The emissivity of a surface increases with increase in surface roughness ... quite low (D) The emissivity of a non-metallic surface decreases with increase in the temperature

Last Answer : (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment

Which of the following equations as suggested by Colebrook and White gives the increase in roughness of a new surface (ε0 ) with age/time (t) (where, ε = roughness of the surface after time't'. α = a co-efficient to be experimentally determined)? (A) ε = ε0 + α.t (B) ε = ε0 + α.t 2 (C) ε = ε0 + α.t 3 (D) ε = ε0 + α.t

Description : Which of the following equations as suggested by Colebrook and White gives the increase in roughness of a new surface (ε0 ) with age/time (t) (where, ε = roughness of the surface after time't'. α = a co-efficient to be experimentally determined ... ε = ε0 + α.t 2 (C) ε = ε0 + α.t 3 (D) ε = ε0 + α.t

Last Answer : (A) ε = ε0 + α.t

The most serious manufacturing defect from fracture toughness point of view is (A) Surface roughness (B) Pores (C) Spherical inclusion (D) Crack

Description : The most serious manufacturing defect from fracture toughness point of view is (A) Surface roughness (B) Pores (C) Spherical inclusion (D) Crack

Last Answer : Option D

Drag co-efficient for flow past immersed body is the ratio of __________ to the product of velocity head and density. (A) Shear stress (B) Shear force (C) Average drag per unit projected area (D) None of these

Description : Drag co-efficient for flow past immersed body is the ratio of __________ to the product of velocity head and density. (A) Shear stress (B) Shear force (C) Average drag per unit projected area (D) None of these

Last Answer : (C) Average drag per unit projected area

The binary diffusivity in gases does not depend upon the (A) Pressure (B) Temperature (C) Nature of the components (D) None of these

Description : The binary diffusivity in gases does not depend upon the (A) Pressure (B) Temperature (C) Nature of the components (D) None of these

Last Answer : (D) None of these

The dew point of an unsaturated gas-vapor mixture does not depend upon the __________ of the mixture. (A) Composition (B) Temperature (C) Total pressure (D) All (A), (B) and (C)

Description : The dew point of an unsaturated gas-vapor mixture does not depend upon the __________ of the mixture. (A) Composition (B) Temperature (C) Total pressure (D) All (A), (B) and (C)

Last Answer : (B) Temperature

Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Description : Shell side pressure drop in a shell and tube heat exchanger does not depend upon the (A) Baffle spacing & shell diameter (B) Tube diameter & pitch (C) Viscosity, density & mass velocity of shell side fluid (D) None of these

Last Answer : (D) None of these

Extensive properties of a thermodynamic system depend upon the __________ of the system. (A) Specific volume (B) Temperature (C) Mass (D) Pressure

Description : Extensive properties of a thermodynamic system depend upon the __________ of the system. (A) Specific volume (B) Temperature (C) Mass (D) Pressure

Last Answer : (C) Mass

The heat capacities for the ideal gas state depend upon the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : The heat capacities for the ideal gas state depend upon the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (B) Temperature

ECE Board Exam March 1996 The characteristics impedance of a transmission line does not depend upon its ________. A. conductor spacing B. conductor diameter C. length D. conductor radius

Description : ECE Board Exam March 1996 The characteristics impedance of a transmission line does not depend upon its ________. A. conductor spacing B. conductor diameter C. length D. conductor radius

Last Answer : C. length

The efficiency of sedimentation tank does not depend upon (A) Depth of tank (B) Length of tank (C) Detention period (D) Velocity of water

Description : The efficiency of sedimentation tank does not depend upon  (A) Depth of tank  (B) Length of tank  (C) Detention period  (D) Velocity of water

Last Answer : (D) Velocity of water

The accuracy of measurement in chain surveying, does not depend upon (A) Length of the offset (B) Scale of the plotting (C) Importance of the features (D) General layout of the chain lines

Description : The accuracy of measurement in chain surveying, does not depend upon (A) Length of the offset (B) Scale of the plotting (C) Importance of the features (D) General layout of the chain lines

Last Answer : (D) General layout of the chain lines

The limiting length of an offset does not depend upon (A) Accuracy of the work (B) Method of setting out perpendiculars (C) Scale of plotting (D) Indefinite features to be surveyed

Description : The limiting length of an offset does not depend upon (A) Accuracy of the work (B) Method of setting out perpendiculars (C) Scale of plotting (D) Indefinite features to be surveyed

Last Answer : (D) Indefinite features to be surveyed

For same weight, same material, same length a. Solid shaft is always stronger than a hollow shaft b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of hollow shaft c. Strength of both the shafts in equal d. Strength of a solid shaft is always weaker and the strength ratio will depend upon Do/Di of hollow shaft

Description : For same weight, same material, same length a. Solid shaft is always stronger than a hollow shaft b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of ... of a solid shaft is always weaker and the strength ratio will depend upon Do/Di of hollow shaft

Last Answer : b. Solid shaft is always weaker than a hollow shaft and strength ratio will depend upon Do/Di of hollow shaft

Deformation drag, which is caused by widespread deformation of fluid around the immersed body(A) Occurs when NReis very small(B) Is primarily a friction drag(C) Is independent of body length(D) Depends mainly on cross-sectional shape

Description : Deformation drag, which is caused by widespread deformation of fluid around the immersed body (A) Occurs when NRe is very small (B) Is primarily a friction drag (C) Is independent of body length (D) Depends mainly on cross-sectional shape

Last Answer : (A) Occurs when NRe is very small

Evaporation losses depend upon (A) Area of the water surface and depth of the water (B) Nature of precipitation and type of vegetation (C) Humidity and wind velocity (D) All the above

Description : Evaporation losses depend upon (A) Area of the water surface and depth of the water (B) Nature of precipitation and type of vegetation (C) Humidity and wind velocity (D) All the above

Last Answer : Answer: Option D

With an increase in size of tube, the rise or depression of liquid in the tube due to surface tension will (A) Decrease (B) Increase (C) Remain unchanged (D) Depend upon the characteristics of liquid

Description : With an increase in size of tube, the rise or depression of liquid in the tube due to surface tension will (A) Decrease (B) Increase (C) Remain unchanged (D) Depend upon the characteristics of liquid

Last Answer : Answer: Option A

The strength and quality of concrete, depend upon: (A) Grading of aggregates (B) Surface area of aggregates (C) Shape of aggregates (D) All the above

Description : The strength and quality of concrete, depend upon: (A) Grading of aggregates (B) Surface area of aggregates (C) Shape of aggregates (D) All the above

Last Answer : Answer: Option D

For laminar flow of a fluid through a packed bed of spheres of diameter d, the pressure drop per unit length of bed depends upon the sphere diameter as (A) d (B) d 2 (C) d 4 (D) d

Description : For laminar flow of a fluid through a packed bed of spheres of diameter d, the pressure drop per unit length of bed depends upon the sphere diameter as (A) d (B) d 2 (C) d 4 (D) d

Last Answer : (D) d

Roughness index of roads, is expressed as (A) Size of the stone on the pavement (B) Number of patches on the pavement (C) Cumulative deformation of surface per horizontal distance (D) Type of the road surface

Description : Roughness index of roads, is expressed as (A) Size of the stone on the pavement (B) Number of patches on the pavement (C) Cumulative deformation of surface per horizontal distance (D) Type of the road surface

Last Answer : Answer: Option C

What is the maximum surface roughness permitted by ASME B31.1 for the sidewall of ring grooves? a) 63 µ in b) 125 µ in. c) 250 µ in. d) 400 µ in

Description : What is the maximum surface roughness permitted by ASME B31.1 for the sidewall of ring grooves? a) 63 µ in b) 125 µ in. c) 250 µ in. d) 400 µ in

Last Answer : a) 63 µ in

What is the maximum surface roughness for tongue and groove and small male and female gasket surfaces? a) 63 µ in b) 125 µ in c) 250 µ in d) 400 µ in

Description : What is the maximum surface roughness for tongue and groove and small male and female gasket surfaces? a) 63 µ in b) 125 µ in c) 250 µ in d) 400 µ in

Last Answer : b) 125 µ in