Which of the following equations as suggested by Colebrook and White gives the increase in roughness of a new surface (ε0 ) with age/time (t) (where, ε = roughness of the surface after time't'. α = a co-efficient to be experimentally determined)? (A) ε = ε0 + α.t (B) ε = ε0 + α.t 2 (C) ε = ε0 + α.t 3 (D) ε = ε0 + α.t

Which of the following equations as suggested by Colebrook and White
gives the increase in roughness of a new surface (ε0
) with age/time (t)
(where, ε = roughness of the surface after time't'. α = a co-efficient to be
experimentally determined)?
(A) ε = ε0 + α.t
(B) ε = ε0 + α.t
2
(C) ε = ε0 + α.t
3
(D) ε = ε0 + α.t
by

1 Answer

Answer :

(A) ε = ε0 + α.t
by

Related questions

Colebrook equation for friction factor in turbulent flow is given by, f -0.5 = -4 loge [(ε/D) + (1.26/NRe √F). It reduces to Nikuradse equation for a value of (ϵ/D) equal to (A) 0(B) 1 (C) ∞ (D) 0.5

Description : Colebrook equation for friction factor in turbulent flow is given by, f -0.5 = -4 loge [(ε/D) + (1.26/NRe √F). It reduces to Nikuradse equation for a value of (ϵ/D) equal to (A) 0 (B) 1 (C) ∞ (D) 0.5

Last Answer : (B) 1

The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient varies with the pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Description : The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient ... pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Last Answer : (B) D-0.2

In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said to have the same hydraulic roughness, when they have equal values of (A) Relative roughness (B) Absolute roughness (C) Friction co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Description : In case of hydraulically smooth pipe, the resistance to flow depends only on the Reynolds number, whereas for a hydraulically rough pipe, the resistance to flow is governed by the relative roughness. Two pipes are said ... co-efficient for flows at equal Reynold number (D) All (A), (B) & (C)

Last Answer : (C) Friction co-efficient for flows at equal Reynold number

In thermal radiation for a black body (where, ε is emissivity and α is absorptivity) (A) α = 1; ε ≠ 1 (B) α ≠ 1, ε = 1 (C) α ≠ 1, ε ≠ 1 (D) α = 1; ε = 1

Description : In thermal radiation for a black body (where, ε is emissivity and α is absorptivity) (A) α = 1; ε ≠ 1 (B) α ≠ 1, ε = 1 (C) α ≠ 1, ε ≠ 1 (D) α = 1; ε = 1

Last Answer : (D) α = 1; ε = 1

The experimentally determined overall order of the reaction, A + B → C + D, is two. Then the (A) Reaction is elementary with a molecularity of 2 (B) Molecularity of the reaction is 2, but the reaction may not be elementary (C) Reaction may be elementary with molecularity of 2 (D) Reaction is elementary but the molecularity may not be 2

Description : The experimentally determined overall order of the reaction, A + B → C + D, is two. Then the (A) Reaction is elementary with a molecularity of 2 (B) Molecularity of the reaction is 2, ... Reaction may be elementary with molecularity of 2 (D) Reaction is elementary but the molecularity may not be 2

Last Answer : (A) Reaction is elementary with a molecularity of 2

The order of a chemical reaction is (A) An experimentally determined quantity (B) Always equal to the total stoichiometric number of reactants (C) Never fractional (D) None of these

Description : The order of a chemical reaction is (A) An experimentally determined quantity (B) Always equal to the total stoichiometric number of reactants (C) Never fractional (D) None of these

Last Answer : (A) An experimentally determined quantity

The order of a chemical reaction (A) Can be determined only experimentally (B) Can be determined from the stoichiometry of the reaction (C) Cannot be zero (D) Can be fractional

Description : The order of a chemical reaction (A) Can be determined only experimentally (B) Can be determined from the stoichiometry of the reaction (C) Cannot be zero (D) Can be fractional

Last Answer : (B) Can be determined from the stoichiometry of the reaction (C) Cannot be zero

Alloxan can experimentally induce diabetes mellitus due to (A) Stimulation of α cells of the islets of langerhans (B) Necrosis of the β cells of the islets (C) Potentiation of insulinase activity (D) Epinephrine like action

Description : Alloxan can experimentally induce diabetes mellitus due to (A) Stimulation of α cells of the islets of langerhans (B) Necrosis of the β cells of the islets (C) Potentiation of insulinase activity (D) Epinephrine like action

Last Answer : Answer : B

In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Description : In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Last Answer : (B) Flows outside the tubes

Pick out the wrong statement. (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment (B) The emissivity of a surface increases with increase in surface roughness (C) The emissivity of a polished surface is quite low (D) The emissivity of a non-metallic surface decreases with increase in the temperature

Description : Pick out the wrong statement. (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment (B) The emissivity of a surface increases with increase in surface roughness ... quite low (D) The emissivity of a non-metallic surface decreases with increase in the temperature

Last Answer : (A) The emissivity of a surface decreases, if it gets corroded by atmospheric environment

Which of the following equations is used for the prediction of activity co-efficient from experiments? (A) Van Laar equation (B) Margules equation (C) Wilson's equation (D) All (A), (B) and (C)

Description : Which of the following equations is used for the prediction of activity co-efficient from experiments? (A) Van Laar equation (B) Margules equation (C) Wilson's equation (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

. Which of the following relationships between co-efficient of friction (μ) between rock & roll and a (half of the angle of nip) of the particle to be crushed is correct? (A) μ > tan α (B) μ ≥ tan α (C) μ > tan 2α (D) μ ≤ tan α

Description : . Which of the following relationships between co-efficient of friction (μ) between rock & roll and a (half of the angle of nip) of the particle to be crushed is correct? (A) μ > tan α (B) μ ≥ tan α (C) μ > tan 2α (D) μ ≤ tan α

Last Answer : (B) μ ≥ tan α

What happens when a chemical bond is formed? (1) energy is always absorbed (2) energy in always released (3) more energy is released than is absorbed (4) energy is neither released nor absorbed Correct (4) Answer – (1) energy is always absorbed Explanation: If a bond is broken, energy is released; and if a bond is formed, energy must have been absorbed. As these occur, a change in the chemical energy of the system also occurs. Within each bond of a molecule is an experimentally determined amount of enemy that upon the breaking of that bond is released into the chemical system. The energy within these bonds are 'stored' and can be easily thought of as potential energy. Upon the breaking of these bonds the energy is released thereby creating usable energy.

Description : What happens when a chemical bond is formed? (1) energy is always absorbed (2) energy in always released (3) more energy is released than is absorbed (4) energy is neither released nor ... as potential energy. Upon the breaking of these bonds the energy is released thereby creating usable energy.

Last Answer : Silver nitrate solution is kept in brown bottles in laboratory because - (1) it reacts with ordinary white bottles (2) brown bottles stops the passage of light through it (3) brown bottles do not react with it (4) brown bottles react with it

All chiral D-sugars rotate plane-polarized light : (a) clockwise (b) counterclockwise (c) +20.0° (d) in a direction that cannot be predicted but must be determined experimentally

Description : All chiral D-sugars rotate plane-polarized light : (a) clockwise (b) counterclockwise (c) +20.0° (d) in a direction that cannot be predicted but must be determined experimentally

Last Answer : in a direction that cannot be predicted but must be determined experimentally

Which one of the following statements is not correct? A Since voltage depends on concentrations, using standard conditions makes it easier to compare different electrochemical reactions. B We have to measure the cell potential to obtain the difference in potential energy because the potential of half-reactions cannot be measured directly. C The direction of a redox reaction can only be determined experimentally. D Half-cell potentials for half-reactions are determined by combining the relevant half-cell with a standardised half-cell.

Description : Which one of the following statements is not correct? A Since voltage depends on concentrations, using standard conditions makes it easier to compare different electrochemical reactions. B We have ... half-reactions are determined by combining the relevant half-cell with a standardised half-cell.

Last Answer : C The direction of a redox reaction can only be determined experimentally. 

The equation f -0.5 = 4.07 loge (NRe √f) -0.6 is called the __________.(A) Colebrook formula (B) Von-Karman equation (C) Fanning equation (D) None of these

Description : The equation f -0.5 = 4.07 loge (NRe √f) -0.6 is called the __________. (A) Colebrook formula (B) Von-Karman equation (C) Fanning equation (D) None of these

Last Answer : (B) Von-Karman equation

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

For infinite parallel planes having emissivities ε1 & ε2, the interchange factor for radiation from surface 1 to surface 2 is given by (A) (ε1 + ε2)/ε1.ε2 (B) ε1.ε2/(ε1 + ε2 - ε1.ε2) (C) ε1.ε2 (D) ε1 + ε

Description : For infinite parallel planes having emissivities ε1 & ε2, the interchange factor for radiation from surface 1 to surface 2 is given by (A) (ε1 + ε2)/ε1.ε2 (B) ε1.ε2/(ε1 + ε2 - ε1.ε2) (C) ε1.ε2 (D) ε1 + ε

Last Answer : Option B

The main purpose of providing fins on heat transfer surface is to increase the (A) Temperature gradient (B) Mechanical strength of the equipment (C) Heat transfer area (D) Heat transfer co-efficient

Description : The main purpose of providing fins on heat transfer surface is to increase the (A) Temperature gradient (B) Mechanical strength of the equipment (C) Heat transfer area (D) Heat transfer co-efficient

Last Answer : (C) Heat transfer area

Transition from laminar flow to turbulent flow is aided by the (A) Surface roughness and curvature (i.e. sharp corners) (B) Vibration (C) Pressure gradient and the compressibility of the flowing medium (D) All (A), (B) & (C)

Description : Transition from laminar flow to turbulent flow is aided by the (A) Surface roughness and curvature (i.e. sharp corners) (B) Vibration (C) Pressure gradient and the compressibility of the flowing medium (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

Pressure drag does not depend upon the(A) Roughness of surface of the body (B) Pressure of main flow only (C) Length of the body in flow direction (D) All (A), (B) and (C)

Description : Pressure drag does not depend upon the (A) Roughness of surface of the body (B) Pressure of main flow only (C) Length of the body in flow direction (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The most serious manufacturing defect from fracture toughness point of view is (A) Surface roughness (B) Pores (C) Spherical inclusion (D) Crack

Description : The most serious manufacturing defect from fracture toughness point of view is (A) Surface roughness (B) Pores (C) Spherical inclusion (D) Crack

Last Answer : Option D

Friction factor for a hydraulically smooth pipe at NRe = 2100 is f1 . If the pipe is further smoothened (i.e., roughness is reduced), the friction factor at the same value of NRe , will (A) Increase (B) Decrease (C) Remain unchanged (D) Increase or decrease depending on the pipe material

Description : Friction factor for a hydraulically smooth pipe at NRe = 2100 is f1 . If the pipe is further smoothened (i.e., roughness is reduced), the friction factor at the same value of NRe , will (A) Increase (B) Decrease (C) Remain unchanged (D) Increase or decrease depending on the pipe material

Last Answer : (A) Increase

Which of the following is not a dimension-less group used in catalysis? (Where, D = dispersion co-efficient, cm2 /sec.D1 = diffusion co-efficient; cm2 /sec L = length of the reactor, cm t = time, sec, v = volumetric flow rate, cm3 /sec. V = volume, cm3 .) (A) Reactor dispersion number (D/vL) (B) Reduced time (vt/V) (C) Thiele modulus L √(k/D1 ) (D) None of these

Description : Which of the following is not a dimension-less group used in catalysis? (Where, D = dispersion co-efficient, cm2 /sec.D1 = diffusion co-efficient; cm2 /sec L = length of the reactor, cm t = time, sec, v = volumetric ... (D/vL) (B) Reduced time (vt/V) (C) Thiele modulus L √(k/D1 ) (D) None of these

Last Answer : (D) None of these

The wetted wall tower is used to determine (A) Individual mass transfer co-efficient (M.T.C.) in gaseous system (B) M.T.C. of individual components in a liquid-liquid system (C) M.T.C. of liquid in liquid-gas system (D) The overall M.T.C. of the system

Description : The wetted wall tower is used to determine (A) Individual mass transfer co-efficient (M.T.C.) in gaseous system (B) M.T.C. of individual components in a liquid-liquid system (C) M.T.C. of liquid in liquid-gas system (D) The overall M.T.C. of the system

Last Answer : (A) Individual mass transfer co-efficient (M.T.C.) in gaseous system

In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

Description : In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

Last Answer : (B) 1/KG = 1/KG + m/KL

The molar excess Gibbs free energy, gE, for a binary liquid mixture at T and P is given by, (gE/RT) = A . x1. x2, where A is a constant. The corresponding equation for ln y1, where y1is the activity co-efficient of component 1, is (A) A . x22 (B) Ax1 (C) Ax2 (D) Ax12

Description : The molar excess Gibbs free energy, gE, for a binary liquid mixture at T and P is given by, (gE/RT) = A . x1. x2, where A is a constant. The corresponding equation for ln y1, where y1is the activity co-efficient of component 1, is (A) A . x22 (B) Ax1 (C) Ax2 (D) Ax12

Last Answer : (A) A . x22

depends upon The Chezy’s constant C in the formula V = C A. Size of the sewer B. Shape of the sewer C. Roughness of sewer surface D. All the above

Description : depends upon The Chezy’s constant C in the formula V = C A. Size of the sewer B. Shape of the sewer C. Roughness of sewer surface D. All the above

Last Answer : ANS: D

Roughness index of roads, is expressed as (A) Size of the stone on the pavement (B) Number of patches on the pavement (C) Cumulative deformation of surface per horizontal distance (D) Type of the road surface

Description : Roughness index of roads, is expressed as (A) Size of the stone on the pavement (B) Number of patches on the pavement (C) Cumulative deformation of surface per horizontal distance (D) Type of the road surface

Last Answer : Answer: Option C

What is the maximum surface roughness permitted by ASME B31.1 for the sidewall of ring grooves? a) 63 µ in b) 125 µ in. c) 250 µ in. d) 400 µ in

Description : What is the maximum surface roughness permitted by ASME B31.1 for the sidewall of ring grooves? a) 63 µ in b) 125 µ in. c) 250 µ in. d) 400 µ in

Last Answer : a) 63 µ in

What is the maximum surface roughness for tongue and groove and small male and female gasket surfaces? a) 63 µ in b) 125 µ in c) 250 µ in d) 400 µ in

Description : What is the maximum surface roughness for tongue and groove and small male and female gasket surfaces? a) 63 µ in b) 125 µ in c) 250 µ in d) 400 µ in

Last Answer : b) 125 µ in

In regard to the enamel surface: A. It is a perfect substance for bonding B. It does not conform to the bonding requirements C. It is the most inorganic, rough part D. It is free from contamination and roughness E. None of the above

Description : In regard to the enamel surface: A. It is a perfect substance for bonding B. It does not conform to the bonding requirements C. It is the most inorganic, rough part D. It is free from contamination and roughness E. None of the above

Last Answer : B. It does not conform to the bonding requirements

________ refer to the surface roughness of the tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape

Description : ________ refer to the surface roughness of the tool a) Micro shape c) Edge shape b) Macro shape d) Gross shape

Last Answer : a) Micro shape

The heat dissipated by from a surface depends upon its temperature and its characteristics like colour, roughness etc. (a) conduction (b) convection (c) radiation (d) any ofthe above

Description : The heat dissipated by from a surface depends upon its temperature and its characteristics like colour, roughness etc. (a) conduction (b) convection (c) radiation (d) any ofthe above

Last Answer : (c) radiation

__________ paint has the minimum absorption co-efficient. (A) Black (B) White lead (C) Grey (D) Light cream

Description : __________ paint has the minimum absorption co-efficient. (A) Black (B) White lead (C) Grey (D) Light cream

Last Answer : (B) White lead

Babbitt metal used for making bearings should have (A) High co-efficient of friction between journal and bearing (B) Ability to retain lubricant on its surface (C) Low co-efficient of friction between journal and bearing (D) Both (B) & (C)

Description : Babbitt metal used for making bearings should have (A) High co-efficient of friction between journal and bearing (B) Ability to retain lubricant on its surface (C) Low co-efficient of friction between journal and bearing (D) Both (B) & (C)

Last Answer : (A) High co-efficient of friction between journal and bearing

Mass transfer co-efficient is directly proportional to DAB 0.5 , according to __________ theory. (A) Penetration (B) Surface renewal (C) Film (D) None of these

Description : Mass transfer co-efficient is directly proportional to DAB 0.5 , according to __________ theory. (A) Penetration (B) Surface renewal (C) Film (D) None of these

Last Answer : (A) Penetration

Mass transfer co-efficient is directly proportional to DAB according to the __________ theory. (A) Film (B) Penetration (C) Surface-renewal (D) None of these

Description : Mass transfer co-efficient is directly proportional to DAB according to the __________ theory. (A) Film (B) Penetration (C) Surface-renewal (D) None of these

Last Answer : (A) Film

Calculation of mass transfer co-efficient is mostly/normally done using __________ theory. (A) Surface renewal (B) Film (C) Penetration (D) None of these

Description : Calculation of mass transfer co-efficient is mostly/normally done using __________ theory. (A) Surface renewal (B) Film (C) Penetration (D) None of these

Last Answer : (B) Film

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

Heat exchangers operating, when the asymptotic range is reached, (A) Provide very large heat transfer co-efficient (B) Results in making part of the heating surface inactive (C) Results in abruptly increased velocity (D) None of these

Description : Heat exchangers operating, when the asymptotic range is reached, (A) Provide very large heat transfer co-efficient (B) Results in making part of the heating surface inactive (C) Results in abruptly increased velocity (D) None of these

Last Answer : (B) Results in making part of the heating surface inactive

Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Description : Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Last Answer : (D) All (A) (B) and (C)

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface). (A) U1 - U2 (B) 1/U1 - 1/U2 (C) 1/U2 - 1/U1 (D) U2 - U1

Description : Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface). (A) U1 - U2 (B) 1/U1 - 1/U2 (C) 1/U2 - 1/U1 (D) U2 - U1

Last Answer : (B) 1/U1 - 1/U2

Which of the following is an undesirable property of a manometricliquid? (A) Non-sticky & non-corrosive nature (B) High vapour pressure (C) Low viscosity & surface tension (D) Low co-efficient of thermal expansion

Description : Which of the following is an undesirable property of a manometricliquid? (A) Non-sticky & non-corrosive nature (B) High vapour pressure (C) Low viscosity & surface tension (D) Low co-efficient of thermal expansion

Last Answer : (B) High vapour pressure

The pressure co-efficient is the ratio of pressure forces to __________ forces. (A) Viscous (B) Inertial (C) Gravity (D) Surface tension

Description : The pressure co-efficient is the ratio of pressure forces to __________ forces. (A) Viscous (B) Inertial (C) Gravity (D) Surface tension

Last Answer : (A) Viscous

Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Description : Even though heat transfer co-efficient in boiling liquids is large, use of fins is advantageous, when the entire surface is exposed to __________ boiling. (A) Film (B) Nucleate (C) Transition (D) All modes of

Last Answer : Option A

Addition of filter aid to the slurry before filtration is done to __________ of the cake. (A) Increase the porosity (B) Increase the compressibility co-efficient (C) Decrease the porosity (D) Decrease the compressibility co-efficient

Description : Addition of filter aid to the slurry before filtration is done to __________ of the cake. (A) Increase the porosity (B) Increase the compressibility co-efficient (C) Decrease the porosity (D) Decrease the compressibility co-efficient

Last Answer : (A) Increase the porosity

Gaseous diffusion co-efficient increases with increase in the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Gaseous diffusion co-efficient increases with increase in the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (B) Temperature