Draw and explain how one lamp can be controlled by two switch. State application of it.

Draw and explain how one lamp can be controlled by two switch. State application of it.
by

2 Answers

Answer :

image


Explanation: This system is commonly used for stair case wiring. It consists of two way switches (the switch operates always in one of the two possible positions) the circuit diagram is as shown in figure above. Assume that the lamp is in between ground floor and first floor with switch S1 is on ground floor and S2 is on first floor. When the position of the switches S1& S2 is as shown in figure then the lamps is ‘ON’. When a person reaches on first floor the lamp is required to be switched ‘OFF’ so the person will change the position of switch S2 such that the lamp will be switched ‘OFF’. 


Application: 1. It is used for Stair case wiring 2. It is also used for Bedroom wiring 3. It used for corridors. 4. It is used for Hospital lighting

by

Answer :

‏Write down the application of two-way switche
by

Related questions

Explain with neat circuit diagram, low pressure mercury vapour lamp.

Description : Explain with neat circuit diagram, low pressure mercury vapour lamp.

Last Answer : Diagram of low pressure mercury vapour lamp:  Working:-  Whenever 1-ph, 230V, AC Supply is provided to the discharge tube of MVL initially to current will flow from Phase to the ... Capacitor: The function of power factor improvement capacitor is to improve the power factor 0.5 to 0.95 

Application one lamp controlled from two places

Description : Application one lamp controlled from two places

Last Answer : Application one lamp controlled from two places: 1. For Stair case wiring 2. Hospital Wiring ( For operating the lamp in room and nursing station) 3. Bedroom Lighting. 

State any four specific requirements of street lighting.

Description : State any four specific requirements of street lighting.

Last Answer : Following specific requirements of street lighting: 1. The street lighting should be such that the object can be seen by driver of any vehicle. 2. The street lighting should be attractive. 3. It should ... . 3) To make the street more attractive. 4) To increase the community value of the street.

State any four characteristics of flood lighting.

Description : State any four characteristics of flood lighting.

Last Answer : Following are the specific characteristics of flood lighting:- 1. Ideal for landscape and architecture lighting. 2. Widely used in home for the showroom purpose, office decoration, garden ... very simple. The control, multicolour light intensity control is also possible in electrical illumination.

State any six factors on which efficiency of lighting depends.

Description : State any six factors on which efficiency of lighting depends.

Last Answer : 1) Level of illumination or degree of illumination: It depends on nature of work to be carried out. The degree of level of illumination also depends on following factors. i) The size of ... Distribution of lux on working plane: The lux level on working plane should be uniformly distributed.

Explain with neat labeled circuit diagram the staircase wiring in which a lamp is controlled from two different locations.

Description : Explain with neat labeled circuit diagram the staircase wiring in which a lamp is controlled from two different locations. 

Last Answer : one lamp controlled from two places: Explanation: 1. The switch S1 (two way switch is located at bottom position of the staircase. 2. The switch S2 is located at top ... the position of S2 lamp will become OFF due to current discontinuity * This process remains continuously 

Use of polar curves in illumination Engg

Description : Use of polar curves in illumination Engg

Last Answer : The polar curves are required to determine the mean horizontal candle power (MHCP) and mean hemispherical candle power (MHSCP).The polar curves are due to limitations of unsymmetrical design shape of ... lighting scheme. 2. To know the intensity of light emitted by the source in different direction

Circuit diagram at tungsten filament bulb

Description : Circuit diagram at tungsten filament bulb

Last Answer : Circuit diagram at tungsten filament bulb

Define each of following terms of illumination — lux, lumen, luminous flux, illumination.

Description : Define each of following terms of illumination — lux, lumen, luminous flux, illumination.

Last Answer : i) Lux :- It is unit of illumination and it is defined as luminous flux falling per unit area  ii) Lumen: It is defined as the luminous flux emitted by a source of one candle power per unit ... the given surface on the working plane. The unit of illumination is lumens/m2 OR lumens/m2 = 1 Lux

A three-phase electrical system is equipped with ground detecting lamps. If one of the lamp goes dark and the other two burn normally before and after the test switch is operated, this indicates _______________. A. the dark lamp must be replaced B. there is a ground in the line with the dark lamp C. there are grounds in two of the three phases D. the voltage to the dark lamp is less than that of the system

Description : A three-phase electrical system is equipped with ground detecting lamps. If one of the lamp goes dark and the other two burn normally before and after the test switch is operated, this indicates _______________. ... of the three phases D. the voltage to the dark lamp is less than that of the system

Last Answer : Answer: A

How To Fix A Lamp With A Broken Switch?

Description : How To Fix A Lamp With A Broken Switch?

Last Answer : Quick Tip -- You Can Save Your Favorite LampLike almost anything else in your home, your lamp can wear down over time. Eventually, its switch may stop working or its bulb might flicker constantly, but a ... switch. You'll save money and you'll never have to throw away one of your favorite lamps.

In the illustrated ground detection system with a ground on phase A, if the switch is opened __________. EL-0009 A. lamp A will dim or go out depending on the severity of the ground B. all three lamps will return to their normal brightness indicating that the bulbs are not burnt out C. lamps B and C will dim lamp A will be brighter D. lamp A will start flickering if the ground is in an AC induction motor

Description : In the illustrated ground detection system with a ground on phase A, if the switch is opened __________. EL-0009 A. lamp A will dim or go out depending on the severity of the ground B. all three ... lamp A will be brighter D. lamp A will start flickering if the ground is in an AC induction motor

Last Answer : Answer: B

The low voltage porcelain is mainly used for (A) Switch block (B) Insulating tubes (C) Lamp sockets (D) All of these

Description : The low voltage porcelain is mainly used for (A) Switch block (B) Insulating tubes (C) Lamp sockets (D) All of these

Last Answer : Answer: Option D

Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 watt lamp. B. The 100 watt lamp will have a greater resistance. C. Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Description : Which of the following statements is true if a 100 watt lamp and a 75 watt lamp are connected in parallel across a 100 volt power supply? A. The 75 watt lamp will draw as much current as the 100 ... Current flow will be the same across each lamp. D. The 75 watt lamp will have a higher resistance.

Last Answer : Answer: D

Describe control of a single lamp from three places. Draw the relevant circuit diagram.

Description : Describe control of a single lamp from three places. Draw the relevant circuit diagram. 

Last Answer : Single lamp control from three places-  It consists of two way switches & intermediate switch, the circuit diagram is as shown in figure. We require two 2-way switches and one intermediate switch and a lamp ... position of any one switch is changed, then the lamp will be turned off.

When paralleling two AC generators, the frequency of the incoming machine immediately prior to closing its breaker should be ____________. A. controlled by placing the governor switch in the automatic position B. adjusted with the voltage regulator C. slightly greater than the bus frequency D. slightly less than the bus frequency

Description : When paralleling two AC generators, the frequency of the incoming machine immediately prior to closing its breaker should be ____________. A. controlled by placing the governor switch in the automatic ... regulator C. slightly greater than the bus frequency D. slightly less than the bus frequency

Last Answer : Answer: C

The frequency of an alternator is controlled from the main switchboard by adjusting the _____________. A. frequency meter B. voltage regulator C. governor control D. sychroscope switch

Description : The frequency of an alternator is controlled from the main switchboard by adjusting the _____________. A. frequency meter B. voltage regulator C. governor control D. sychroscope switch

Last Answer : Answer: C

What is the difference between Silicon Controlled Switch (SCS) and Gate Turn-off Switch (GTO)?

Description : What is the difference between Silicon Controlled Switch (SCS) and Gate Turn-off Switch (GTO)?

Last Answer : Ans-scs is nothing but it is the silicon controlled switch as an SCR but gate turn off is that in which one of the turnoff method of SCR

Draw & explain touch plate switch using IC555.

Description : Draw & explain touch plate switch using IC555.

Last Answer : It is construct form monostable multivibrator , when metal plates touch by finger then voltage at pin number 2 goes to below 1/3 Vcc then output of lower comparator becomes high hence flip flop set and ... then output of timer goes low and it low till up to the metal plates touch by finger .

Draw the symbol and state the applications of : 1) Push button switch 2) Selector switch 3) Solenoid valve 4) Limit switch

Description : Draw the symbol and state the applications of : 1) Push button switch 2) Selector switch 3) Solenoid valve 4) Limit switch

Last Answer : 1) Push Button  It is used in start-stop control circuit 2) Selector Switch : It is used to select one input out of many,  3) Solenoid valve: is used to control flow of fluid such as air, pressurized oil.  4) Limit switch: It is used to detect presence of object

Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Description : Give the operation of single phase full wave bridge controlled converter with RL load with a neat diagram. Also draw its waveform.

Last Answer : Single phase fully control bridge converter with RL load: 1. During positive half cycle of input voltage, T1 and T2 are forward biased and during negative half cycle, T3 and T4 are forward biased. Therefore, T1-T2 ... cycle till the firing of next pair of SCRs as shown in the waveform.

Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Description : Draw a neat diagram of 1Ф half wave controlled converter with RL load. Give its operation.

Last Answer : Single phase fully controlled half wave converter:  The circuit diagram of single-phase half-wave controlled rectifier with RL load and without freewheeling diode is shown in Fig. (a). The SCR T is ... , when again pulse is applied, the SCR is turned on & the above cycle is repeated. 

Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Description : Which of the following statements represents an application of a silicon controlled rectifier? A. To provide DC power for a main propulsion motor. B. For use as a voltage reference diode. C. For sensing flame in an automated burner. D. To eliminate power supply hum.

Last Answer : Answer: A

Which altra low volume sprayer is used for controlled droplet application a). Herbi sprayer b). Micron herbi sprayer c). Both a and b d). None of these

Description : Which altra low volume sprayer is used for controlled droplet application a). Herbi sprayer b). Micron herbi sprayer c). Both a and b d). None of these

Last Answer : c). Both a and b

What will be an output of the following code if value of variable application is 1? switch(application) -Technology

Description : What will be an output of the following code if value of variable application is 1? switch(application) -Technology

Last Answer : The output is:OS

…………… are very effective because a mode switch is not required to switch from one thread to another. A) Kernel-level threads B) User-level threads C) Alterable threads D) Application level threads

Description : …………… are very effective because a mode switch is not required to switch from one thread to another. A) Kernel-level threads B) User-level threads C) Alterable threads D) Application level threads

Last Answer : B) User-level threads

In the following list of devices which device is used in network layer? (1) Repeaters (2) Router (3) Application Gateway (4) Switch

Description : In the following list of devices which device is used in network layer? (1) Repeaters (2) Router (3) Application Gateway (4) Switch

Last Answer : Router

Draw and explain the working principle of turbine type flow meter. Mention its Application area.

Description : Draw and explain the working principle of turbine type flow meter. Mention its Application area.

Last Answer : Working Principle: The flow of liquid past the wheel causes the wheel to rotate at a rate which is proportional to the velocity of the fluid. A voltage pulse is induced in ... Suitable for low viscosity high flow measurements 3) Used in petrochemical industries, in Aerospace applications etc.

for Delta-Star connection of 3-phase transformer: i) Draw the connection diagram ii) List any two advantages of this connection iii) State its area of application.

Description : for Delta-Star connection of 3-phase transformer: i) Draw the connection diagram ii) List any two advantages of this connection iii) State its area of application. 

Last Answer : Disadvantages: i) In this type of connection, the secondary voltage is not in phase with the primary. Hence it is not possible to operate this connection in parallel with star-star or delta-delta ... iv) As line current is equal to phase current the conductor size of winding should be large. 

Draw symbol and state one application of zener diode and LED.

Description : Draw symbol and state one application of zener diode and LED.

Last Answer : Diagram: Application of Zener diode:  It is used as voltage regulator. Used in protection circuits for MOSFET. Used in pulse amplifier. Used in clipping circuits. ... alarm systems 7-segment, 16- segment and dot matrix displays Indicating power ON/OFF conditions

Draw a neat of full floating rear axle. Label all the parts. State an application of Semi floating, three quarter floating and full floating rear axle.

Description : Draw a neat of full floating rear axle. Label all the parts. State an application of Semi floating, three quarter floating and full floating rear axle.

Last Answer : Semi floating: light motor vehicle three quarter floating:light motor vehicle full floating rear axle: heavy commercial vehicles

Draw a neat sketch of Transfer case arrangement. Label all the parts and state the application of transfer case in Automobiles.

Description : Draw a neat sketch of Transfer case arrangement. Label all the parts and state the application of transfer case in Automobiles. 

Last Answer : Working of transfer case: When the shifter-A is at the central position as shown in fig. here neither the gear G1and nor the gear G2 is connected to the input shaft, it is known as neutral ... in four wheel drive vehicle along with main gearbox to transmit torque and power to the rear axle. 

Draw construction diagram of LVDT with label. Also state the application of LVDT.

Description : Draw construction diagram of LVDT with label. Also state the application of LVDT. 

Last Answer : Application of LVDT 1) L.V.D.T as a primary transducer can be used for displacement measurement ranging from fraction of a mm to a few cm 2) Acting an secondary transducer, used to measure force, weight and pressure. 

Explain how double test lamp used for testing earth?

Description : Explain how double test lamp used for testing earth?

Last Answer : Ans: Double test lamp having three leads. Centre lead should be connected to earth, left side lead to be connected on positive side (+ve), right side to be connected on negative side (-ve) If both ... ) in the coach. If right side bulb glows brightly it indicates positive earth (+ve) in the coach.

Explain the working of HPMV Lamp with neat diagram.

Description : Explain the working of HPMV Lamp with neat diagram.

Last Answer : High-pressure Mercury-Vapour Lamp (HPMVL):  Working:  * Whenever 1-ph, 230V, AC Supply is provided to the discharge tube of MVL, initially the current flows from Phase to the choke to ... : The function of power factor improvement capacitor is to improve the power factor from 0.5 to 0.95.

The work done by a body on application of a constant force is the product of the constant force and distance travelled by the body in the direction of force. Express this in the form of a linear equation in two variables and draw its graph by taking the constant force as 3 units. -Maths 9th

Description : The work done by a body on application of a constant force is the product of the constant force and distance travelled by the body in the direction of force. Express this in the form of a linear equation in two variables and draw its graph by taking the constant force as 3 units. -Maths 9th

Last Answer : Solution :-

Draw the following and write application of each. i. Well type manometer ii. Bellows.

Description :  Draw the following and write application of each. i. Well type manometer ii. Bellows.

Last Answer : 1. Well type manometer Application : Manometers are used in flow, pressure and force measurement systems.   2. Bellows  Applications : i. These are used in the large indicating gauges, recorders where space is not a problem. ii. It is useful in pneumatic controllers.

Draw Hysteresis loop for Hard steel and soft steel. Also write one application of each material.

Description : Draw Hysteresis loop for Hard steel and soft steel. Also write one application of each material.

Last Answer : Application of Hard steel:  Fig. (a) Shows hysteresis loop for hard steel. Such materials are used for producing permanent magnets. Such a hysteresis loop represents a large residual ... Residual flux & coercive force are less. Hence material can be used for making the electromagnets. 

State the use of following: (i) Screw driver (ii) Nose pliers (iii) Wire gauge (iv) Test lamp

Description : State the use of following: (i) Screw driver (ii) Nose pliers (iii) Wire gauge (iv) Test lamp 

Last Answer : i) Screw Driver: Usually hand-operated, for turning screws with slotted heads for losing and tightening the screws.  ii) Nose pliers : To hold and tight the wires   iii) Wire Gauge: To ... supply voltage, Verification of voltage & current in the system and also check the open circuit fault. 

State the selection criterion of the lamp for various purposes.

Description : State the selection criterion of the lamp for various purposes.

Last Answer : Selection criterion of the lamp for various purposes:  While selecting a lamp for a particular purpose, the available lamps are compared on the basis of following criteria: * Light output ... such as ballasts * Compatibility with the electrical system * Suitability for the operating environment