What are the design objectives of Electrical System?

What are the design objectives of Electrical System?
by

1 Answer

Answer :

a. To evacuate generated electrical power.

b. To provide required power to SUT, UT, DG, UPS, and CUPS.

c. To provide required emergency power from onsite DG, UPS & CUPS.

d. To provide Fast transfer in event of Class IV failure. Emergency transfer in events of Class III and Class II failure.

e. Load shedding in event of one DG available.

f. To provide un-interruptible or few milli seconds interrupted power supply by

UPS and un-interruptible power supply by CUPS.

g. To provide operational flexibility by providing required qualities of requirement.

h. To provide isolation, Alarms, indication, protection of the system.

i. To provide fire protection.

j. To provide surge and lightning protection.

k. To provide adequate lighting.

l. To provide equipment earthing, system earthing, and personnel protection.

m. To provide necessary electrical and physical isolation of electrical equipments. 
by

Related questions

What are the design guidelines for electrical system?

Description : What are the design guidelines for electrical system?

Last Answer : a. All safety related equipments are in control building, SRPH and are designed for SSE conditions. As per studies seismic condition is not there within 5 kms and nearest zone is away from ... operating island. h. To reduce fault level in lighting circuits separate 280-kVA transformer is provided.

Statement of scope and objectives, opportunities and performance criteria …………. A) Problem definition B) System analysis C) System Design D) Documentation

Description : Statement of scope and objectives, opportunities and performance criteria …………. A) Problem definition B) System analysis C) System Design D) Documentation

Last Answer : A) Problem definition

An auditor should design the written audit program so that a. All material transactions will be selected for substantive testing. b. Substantive tests prior to the balance sheet date will be minimized. c. Each account balance will be tested under either tests of controls or tests of transactions. d. The audit procedures selected will achieve specific audit objectives

Description : An auditor should design the written audit program so that a. All material transactions will be selected for substantive testing. b. Substantive tests prior to the balance sheet date ... controls or tests of transactions. d. The audit procedures selected will achieve specific audit objectives

Last Answer : The audit procedures selected will achieve specific audit objectives

.As part of audit planning, CPAs should design audit programs for each individual audit and should include audit steps and procedures to a. Ensure that only material items are audited. b. Provide assurance that the objectives of the audit are met. c. Detect and eliminate fraud. d. Increase the amount of management information available

Description : .As part of audit planning, CPAs should design audit programs for each individual audit and should include audit steps and procedures to a. Ensure that only material items are audited. b. Provide ... are met. c. Detect and eliminate fraud. d. Increase the amount of management information available

Last Answer : Provide assurance that the objectives of the audit are met.

An auditor should design a written audit program so that: a. All material transactions will be selected for substantive testing. b. Substantive tests prior to the balance sheet date will be minimized. c. The audit procedures selected will achieve specific audit objectives. d. Each account balance will be tested under either tests of controls or tests of transactions

Description : An auditor should design a written audit program so that: a. All material transactions will be selected for substantive testing. b. Substantive tests prior to the balance sheet date will be minimized ... . d. Each account balance will be tested under either tests of controls or tests of transactions

Last Answer : The audit procedures selected will achieve specific audit objectives

Research design of a study should not include (i) Objectives (ii) Hypothesis (iii) Findings (iv) Blue print of Research

Description : Research design of a study should not include (i) Objectives (ii) Hypothesis (iii) Findings (iv) Blue print of Research

Last Answer : (iii) Findings

To create vehicle of information to provide evidence in the development process and to monitor the process. This is one of the objectives of A) Analysis B) Design C) Development D) Documentation

Description : To create vehicle of information to provide evidence in the development process and to monitor the process. This is one of the objectives of A) Analysis B) Design C) Development D) Documentation

Last Answer : D) Documentation

What are the objectives of software design? How do we transform an informal design to a detailed design?

Description : What are the objectives of software design? How do we transform an informal design to a detailed design?

Last Answer : Ans Objectives of software design The purpose of the design phase is to plan a solution of the problem specified by the requirements document. This phase is the first step in moving from ... details as the design is developed with constant backtracking to correct earlier, less formal, designs.

Write four objectives of concrete mix design.

Description : Write four objectives of concrete mix design. 

Last Answer : i. To achieve a specified compressive strength of concrete. ii. To reduce wastage of concrete by correct proportioning. iii. To achieve economy by selecting appropriate concrete ingredients. iv. To maintain ... yield per bag of cement. vi. To ensure less defects and enhanced durability of concrete.

What are the objectives of tariff?

Description : What are the objectives of tariff?

Last Answer : Electrical energy is sold at such a rate so that it not only returns the cost but also earns reasonable profit. Therefore, a tariff must cover the following items: transmitting and distributing equipment. equipment. costs etc.

Which of the following statements is/are true regarding requirements for receptacle outlets aboard vessels? A. Each receptacle outlet operating at 100 volts or more must have a grounding pole. B. Outlets connecting a lifeboat and the vessel's electrical system must have threaded plugs. C. Machinery spaces must contain sufficient outlets for lighting all machinery with a portable light having a 50 foot flexible cord. D. All of the above.

Description : Which of the following statements is/are true regarding requirements for receptacle outlets aboard vessels? A. Each receptacle outlet operating at 100 volts or more must have a grounding pole. B. Outlets ... machinery with a portable light having a 50 foot flexible cord. D. All of the above.

Last Answer : Answer: A

A diesel driven emergency generator is prevented from being paralleled with the ship's service generators by __________. A. an electrical interlock system B. an automatic paralleling trip switch C. the synchronizing oscilloscope D. the reverse current relay

Description : A diesel driven emergency generator is prevented from being paralleled with the ship's service generators by __________. A. an electrical interlock system B. an automatic paralleling trip switch C. the synchronizing oscilloscope D. the reverse current relay

Last Answer : Answer: A

A three-phase electrical system is equipped with ground detecting lamps. If one of the lamp goes dark and the other two burn normally before and after the test switch is operated, this indicates _______________. A. the dark lamp must be replaced B. there is a ground in the line with the dark lamp C. there are grounds in two of the three phases D. the voltage to the dark lamp is less than that of the system

Description : A three-phase electrical system is equipped with ground detecting lamps. If one of the lamp goes dark and the other two burn normally before and after the test switch is operated, this indicates _______________. ... of the three phases D. the voltage to the dark lamp is less than that of the system

Last Answer : Answer: A

In a three-phase electrical system, three ground detecting lamps are provided. If all three lamps REMAIN at half-brilliance when the ground detecting test switch is operated, ______________. A. there is a slight ground on all three phases B. the switch must be replaced C. there are no grounds present D. the light bulbs are of improper voltage

Description : In a three-phase electrical system, three ground detecting lamps are provided. If all three lamps REMAIN at half-brilliance when the ground detecting test switch is operated, ______________. A. there is a ... must be replaced C. there are no grounds present D. the light bulbs are of improper voltage

Last Answer : Answer: C

In a three-phase electrical system, three ground detecting lamps are provided. One lamp goes dark and the others increase in brightness. When the test button is pushed, all lamps have equal illumination. You should conclude that ____________. A. there is a ground on the line with the dark lamp B. the dark lamp must be replaced C. there are grounds on the lines with the bright lamps D. this is a normal condition

Description : In a three-phase electrical system, three ground detecting lamps are provided. One lamp goes dark and the others increase in brightness. When the test button is pushed, all lamps have equal illumination. You ... C. there are grounds on the lines with the bright lamps D. this is a normal condition

Last Answer : Answer: A

In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Description : In an alternating current electrical system, a low system power factor is a direct sign of _____________. A. wasted energy B. efficient operation C. a short in the exciter field windings D. an excessive number of minor system grounds

Last Answer : Answer: A

Accidental grounds in a shipboard electrical system must be repaired as soon as possible as they will ____________. A. result in immediate power outages B. damage circuit breakers C. appear on the ground detection system D. damage insulation and may cause outages

Description : Accidental grounds in a shipboard electrical system must be repaired as soon as possible as they will ____________. A. result in immediate power outages B. damage circuit breakers C. appear on the ground detection system D. damage insulation and may cause outages

Last Answer : Answer: D

A ground is indicated by the ground-detecting system on the main electrical switchboard. The FIRST step in locating the actual ground is to _____________. A. close all circuit breakers in the distribution panel until the ground detector indicates normal B. open the individual circuit breakers, one by one until the ground detection system indicates normal C. change over generators D. check each circuit with a megohmmeter

Description : A ground is indicated by the ground-detecting system on the main electrical switchboard. The FIRST step in locating the actual ground is to _____________. A. close all circuit breakers in ... ground detection system indicates normal C. change over generators D. check each circuit with a megohmmeter

Last Answer : Answer: B

Which of the following represents a characteristic of an ungrounded electrical distribution system? A. Accidental contact between one line and ground does not cause an outage. B. Double ground faults on different phases will not cause an outage. C. Ground detection systems are unnecessary. D. Accidental contact between one line and ground will always cause an outage.

Description : Which of the following represents a characteristic of an ungrounded electrical distribution system? A. Accidental contact between one line and ground does not cause an outage. B. Double ground faults on ... unnecessary. D. Accidental contact between one line and ground will always cause an outage.

Last Answer : Answer: A

If the illustrated motor fails to start and gives a loud hum when the start button is pushed, the problem is ________. EL-0007 A. one of the phases to the motor is not energized because of an open motor lead B. the 'Disc.sw.' is open C. power to 'L1' at the 'Disc.sw.' is not energized because of a problem with the ship's electrical distribution system D. 'OL1' is open because of 'T1' overload causing the motor to single phase

Description : If the illustrated motor fails to start and gives a loud hum when the start button is pushed, the problem is ________. EL-0007 A. one of the phases to the motor is not energized because of ... electrical distribution system D. 'OL1' is open because of 'T1' overload causing the motor to single phase

Last Answer : Answer: A

A switchboard, for a AC electrical distribution system, will be provided with which of the following components? A. Frequency meter. B. Ammeter C. Voltmeter D. All of the above

Description : A switchboard, for a AC electrical distribution system, will be provided with which of the following components? A. Frequency meter. B. Ammeter C. Voltmeter D. All of the above

Last Answer : Answer: D

A switchboard for an AC electrical system requires the use of which of the following devices? A. Frequency meter. B. Ohmmeter. C. Induction voltage regulator. D. Current transformer governor.

Description : A switchboard for an AC electrical system requires the use of which of the following devices? A. Frequency meter. B. Ohmmeter. C. Induction voltage regulator. D. Current transformer governor.

Last Answer : Answer: A

The part of the shipboard electrical system used to control the distribution of power to the branch circuits, is the _____________. A. bridge control panel B. disconnect links C. governor relay box D. main switchboard

Description : The part of the shipboard electrical system used to control the distribution of power to the branch circuits, is the _____________. A. bridge control panel B. disconnect links C. governor relay box D. main switchboard

Last Answer : Answer: D

How the electrical power system protection is divided?

Description : How the electrical power system protection is divided?

Last Answer : The overall system protection is divided into • Generator protection • Transformer protection • Busbar protection • Transmission line protection and • Feeder protection

What is the difference between 3 phase 3 wire & 3 phase 4 wire system in electrical system?

Description : What is the difference between 3 phase 3 wire & 3 phase 4 wire system in electrical system?

Last Answer : The answer is very simple. A 3-phase 3-wire system does not contain a neutral. This occurs when you have 3-phase loads such as motors that do not require a neutral. A 3-phase 4-wire system has a neutral. A ... enough in HV side - .In utility point 4 ( 230 , 380 or 415 V)wire required in LV side.

How harmonics generated in electrical power distribution system?

Description : How harmonics generated in electrical power distribution system?

Last Answer : Harmonic frequencies are integral multiples of the fundamental supply frequency, i.e. for a fundamental of 50 Hz, the third harmonic would be 150 Hz and the fifth harmonic would be 250 ... the corresponding application guides, since the electricity grid's protection system should cut off the fault.

State the factors, for the choice of electrical system for an aero turbine.

Description : State the factors, for the choice of electrical system for an aero turbine.

Last Answer : A:The choice of electrical system for an aero turbine is guided by three factors: Type of electrical output: dc, variable- frequency ac, and constant- frequency ac. Aero turbine ... energy output: in conjunction with battery or other form of storage, or interconnection with power grid.

What are the main two divisions of MAPS electrical system and what do you understand by it?

Description : What are the main two divisions of MAPS electrical system and what do you understand by it? 

Last Answer : The two main divisions of MAPS electrical system are a. Main output system. Output system supplies power to the grid. Generated voltage is stepped up to 220 kV from 16.5 kV and supplied to grid. b. ... voltage is stepped down to 6.6 kV and 415 V from 16.5 kV and supplies to auxiliary loads. 

What are the advantages of VSCF wind electrical system?

Description : What are the advantages of VSCF wind electrical system?

Last Answer : Advantages of VSCF wind electrical system are: No complex pitch changing mechanism is needed. Aero turbine always operates at maximum efficiency point. Extra energy in the high ... extracted Significant reduction in aerodynamic stresses, which are associated with constant - speed operation.

State the factors, for the choice of electrical system for an aero turbine.

Description : State the factors, for the choice of electrical system for an aero turbine.

Last Answer : The choice of electrical system for an aero turbine is guided by three factors: Type of electrical output: dc, variablefrequency ac, and constant- frequency ac. Aero turbine rotational speed ... output: in conjunction with battery or other form of storage, or interconnection with power grid.

What skills are required to do the electrical design job?

Description : What skills are required to do the electrical design job?

Last Answer : To have an electrical design job, you absolutely must be knowledgeable about hazardous area electrical systems. You may also need Microstation experience, design experience, and experience in an engineering industry.

Which of the following is the basic consideration in the design of insulation ? (a) Electrical considerations (b) Mechanical considerations (c) Thermal considerations (d) All of the above

Description : Which of the following is the basic consideration in the design of insulation ? (a) Electrical considerations (b) Mechanical considerations (c) Thermal considerations (d) All of the above

Last Answer : (d) All of the above

What is phase angle in electrical engineering ?

Description : What is phase angle in electrical engineering ?

Last Answer : In electrical engineering, phase angle is the angular difference in phase between two sinusoidal waves or signals. It is typically measured in degrees or radians, and it represents the amount of shift or ... and current in an AC circuit can affect the power factor and the efficiency of the circuit.

Coast Guard Regulations (46 CFR) state that the minimum conductor size allowed for use in flexible electrical cords is ____________. A. 10 AWG B. 14 AWG C. 18 AWG D. 20 AWG

Description : Coast Guard Regulations (46 CFR) state that the minimum conductor size allowed for use in flexible electrical cords is ____________. A. 10 AWG B. 14 AWG C. 18 AWG D. 20 AWG

Last Answer : Answer: C

When maintenance personnel are working on electrical equipment, all supply switches should be secured in the open position and tagged specifically by the _____________. A. watch engineer B. chief engineer or first assistant C. chief electrician D. person performing the repair

Description : When maintenance personnel are working on electrical equipment, all supply switches should be secured in the open position and tagged specifically by the _____________. A. watch engineer B. chief engineer or first assistant C. chief electrician D. person performing the repair

Last Answer : Answer: D

Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. Secure and tag the supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Description : Before any work on electrical or electronic equipment is performed, which of the following precautions should be carried out? A. De-energize the applicable switchboard bus. B. Bypass the interlocks. C. ... supply circuit breaker in the open position. D. Station a man at the circuit supply switch.

Last Answer : Answer: C

Which of the following statements concerning electrical cables is correct? A. Where they pass through watertight bulkheads, they should be fitted with watertight stuffing boxes. B. Electric cable coverings should never be grounded. C. Electrical cables must be rigidly held in place by welding of armored cable, or glued in place where nonmetallic insulation is used. D. All of the above.

Description : Which of the following statements concerning electrical cables is correct? A. Where they pass through watertight bulkheads, they should be fitted with watertight stuffing boxes. B. Electric cable coverings should ... , or glued in place where nonmetallic insulation is used. D. All of the above.

Last Answer : Answer: A

Which of the following statements represents the FIRST precaution to be taken prior to working on any installed electrical component? A. Wear rubber gloves and boots. B. Use only approved nonconducting tools. C. Ground the case of the machine before beginning any repairs. D. Open the supply circuits and tag the switches.

Description : Which of the following statements represents the FIRST precaution to be taken prior to working on any installed electrical component? A. Wear rubber gloves and boots. B. Use only approved nonconducting ... the machine before beginning any repairs. D. Open the supply circuits and tag the switches.

Last Answer : Answer: D

The emergency electrical power source on tank vessels over 500 GT on an international voyage, should be capable of continuous operation under emergency load for _____________. A. 6 hours B. 12 hours C. 18 hours D. 24 hours

Description : The emergency electrical power source on tank vessels over 500 GT on an international voyage, should be capable of continuous operation under emergency load for _____________. A. 6 hours B. 12 hours C. 18 hours D. 24 hours

Last Answer : Answer: C

Which of the spaces listed is defined as a 'location requiring an exceptional degree of protection' when considering the installation of shipboard electrical equipment? A. Machinery space B. Chart room C. Console room D. Accommodation space

Description : Which of the spaces listed is defined as a 'location requiring an exceptional degree of protection' when considering the installation of shipboard electrical equipment? A. Machinery space B. Chart room C. Console room D. Accommodation space

Last Answer : Answer: A

In the schematic of the electrical circuit shown in the illustration, what is the value of the total capacitance, when compared to the value of equal individual capacitors? EL-0038 A. Equal B. Half C. Double D. Squared

Description : In the schematic of the electrical circuit shown in the illustration, what is the value of the total capacitance, when compared to the value of equal individual capacitors? EL-0038 A. Equal B. Half C. Double D. Squared

Last Answer : Answer: C

As shown in the illustration, the symbol is used in electrical drawings to designate a ____________. EL-0026 A. limit switch with one set of normally open contacts B. maintaining type push button with an electrical interlock C. sustaining type push button with a mechanical interlock D. normally closed contact held open mechanically by an interlock

Description : As shown in the illustration, the symbol is used in electrical drawings to designate a ____________. EL-0026 A. limit switch with one set of normally open contacts B. maintaining type ... type push button with a mechanical interlock D. normally closed contact held open mechanically by an interlock

Last Answer : Answer: C

The electrical schematic illustrated in figure A, depicts a/an _____________. EL-0059 A. autotransformer B. Delta Wye transformer C. primary EMF generator D. potential transformer

Description : The electrical schematic illustrated in figure A, depicts a/an _____________. EL-0059 A. autotransformer B. Delta Wye transformer C. primary EMF generator D. potential transformer

Last Answer : Answer: D

The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across 'R1', 'R2' and 'R3' will be different if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3

Description : The electrical diagram shown in the illustration shows _____________. EL-0021 A. 'R1', 'R2', and 'R3' are connected is series B. 'R1', 'R2', and 'R3' are connected in parallel C. the voltages measured across ... if 'R1', 'R2' and 'R3' have different values D. the total resistance equals R1 + R2 + R3

Last Answer : Answer: B

The electrical diagram shown in the illustration represents a ___________. EL-0054 A. series-wound motor B. shunt-wound motor C. compound-wound motor D. flat-compounded motor

Description : The electrical diagram shown in the illustration represents a ___________. EL-0054 A. series-wound motor B. shunt-wound motor C. compound-wound motor D. flat-compounded motor

Last Answer : Answer: C

Regarding the illustrated electrical schematic, 'S1-P', 'S1-Q', and 'S1-R' represent ____________. EL-0016 A. capacitors B. normally-closed contacts C. normally-open contacts D. normally-closed pushbutton switches

Description : Regarding the illustrated electrical schematic, 'S1-P', 'S1-Q', and 'S1-R' represent ____________. EL-0016 A. capacitors B. normally-closed contacts C. normally-open contacts D. normally-closed pushbutton switches

Last Answer : Answer: C

The electrical diagram shown in the illustration is used to depict a/an ____________. EL-0015 A. resistance circuit B. inductive circuit C. stepdown circuit D. capacitive circuit

Description : The electrical diagram shown in the illustration is used to depict a/an ____________. EL-0015 A. resistance circuit B. inductive circuit C. stepdown circuit D. capacitive circuit

Last Answer : Answer: D

The electrical schematic shown in the illustration indicates the lighting feeder circuit is _____________. EL-0014 A. three phase, 450 volt, and 60 cycle B. three phase, 120 volt, and 60 cycle C. single phase, 120 volt, and 60 cycle D. not specified

Description : The electrical schematic shown in the illustration indicates the lighting feeder circuit is _____________. EL-0014 A. three phase, 450 volt, and 60 cycle B. three phase, 120 volt, and 60 cycle C. single phase, 120 volt, and 60 cycle D. not specified

Last Answer : Answer: A

The electrical schematic shown in the illustration represents a/an ____________. EL-0017 A. across-the-line starter B. primary-resistor starter C. autotransformer starter D. part-winding starter

Description : The electrical schematic shown in the illustration represents a/an ____________. EL-0017 A. across-the-line starter B. primary-resistor starter C. autotransformer starter D. part-winding starter

Last Answer : Answer: A