Description : The coils of spring which are in contact with the seat and do not contribute to spring action are called (A) resting coils (B) static coils (C) inactive coils (D) ideal coils
Last Answer : (C) inactive coils
Description : The ends of spring, which are in contact with the seat, are (A) Active coils (B) Inactive coils (C) Transmit maximum force (D) Do not transmit any force
Last Answer : (B) Inactive coils
Description : Active and inactive, both types of coils support the load although both don’t participate in spring action. a) Active coils don’t support the load b) Inactive coils don’t support the load c) Both active and inactive don’t support the load d) Both active and inactive support the load
Last Answer : b) Inactive coils don’t support the load
Description : If a spring has plain ends then number of inactive coils is? a) 1 b) 2 c) 3 d) 0
Last Answer : d) 0
Description : The maximum shear stress in spring wire is induced at (A) Inner surface of the coil (B) Outer surface of the coil (C) Central surface of the coil (D) End coils
Last Answer : (A) Inner surface of the coil
Description : If uncompressed length of spring is 40mm and number of coils 10mm, then pitch of coil is? a) 4 b) 40/9 c) 40/11 d) None of the mentioned
Last Answer : b) 40/9
Description : If number of coils are 8 and wire diameter of spring 3mm, then solid length is given by? a) None of the listed b) 27mm c) 24mm d) 21mm
Last Answer : c) 24mm
Description : Spring having square ends has 1 inactive coil. a) True b) False
Last Answer : b) False
Description : Axial length of the spring which is so compressed that the adjacent coils touch each other. (A) compressed length (B) solid length (C) free length (D) none of the above
Last Answer : (B) solid length
Description : If the spring is compressed completely and the adjacent coils touch each other,the the length of spring is called as? a) Solid length b) Compressed length c) Free length d) None of the mentioned
Last Answer : a) Solid length
Description : Sliding contact bearings, also called plain bearings have no problem of wear. a) True b) False
Description : The distribution of the forces along the length of key fitted in a shaft (A) Varies linearly (B) Is uniform throughout (C) Varies exponentially, being more near the torque-input end (D) Varies exponentially, being less near the torque-input end
Last Answer : (C) Varies exponentially, being more near the torque-input end
Description : Some dividing cells exit the cell cycle and enter vegetative inactive stage. This is called quiescent stage (G0). This process occurs at the end of (a) M phase (b) G1 phase (c) S phase (d) G2 phase.
Last Answer : (b) G1 phase
Description : A full journal bearing having clearance to radius ratio of 1/100, using a lubricant with μ=28×10-3 Pa s supports the shaft journal running at N = 2400 rpm If bearing pressure is 1.4 MPa, the Somerfield number is [IES-2001] (a) 8×10-3 (b) 8×10-5 (c) 0.48 (d) 0.48×10
Last Answer : (a) S = (μN s /p) (r/c) 2
Description : Calculate the coefficient of fluctuation of speed if maximum speed is 2500rpm and minimum speed is 1800rpm. 1. 1.44 2. 1.33 3. 0.33 4. 0.44
Last Answer : 3. 0.33
Description : The coefficient of fluctuation of speed, when the maximum and minimum speeds are 300rpm and 290 rpm (A) 0.034 (B) 0.017 (C) 0.008 (D) 0/004
Last Answer : (A) 0.034
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering the static load capacity of the sh (a) True (b) False
Last Answer : (a) True
Description : A total permanent deformation of 0.0001 of the ball diameter is taken for considering static load capacity of the shaft. a) True b) False
Last Answer : a) True
Description : Wahl factor to account for direct shear stress and stress concentration due to curvature for helical springs is given by, (A) (4C - 1/4C - 4) + 0.615/C (B) (4C - 1/4C + 4) + 0.615/C (C) (4C + 1/4C - 4) + 0.615/C (D) (4C + 1/4C + 4) + 0.615/C
Last Answer : (A) (4C - 1/4C - 4) + 0.615/C
Description : For a helical torsion sprig, the stress concentration factor at outer fibre is? Give spring index=5. a) 0.78 b) 0.87 c) 1.87 d) 0.69
Last Answer : b) 0.87
Description : The diameter of knuckle pin in the knuckle joint is usually... A. 0.5 d B. 0.8 d C. 1.5 d D. d
Last Answer : D. d
Description : The angle of V-welded joint in a pressure vessel 30 to 45 0 40 to 55 0 55 to 70 0 None
Last Answer : 55 to 70 0
Description : The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None
Last Answer : c. 45 0
Description : Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None
Last Answer : b. 0.707x leg
Description : Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None
Last Answer : (i)0.707 tl
Description : If length of weld is l and leg h, then area of throat can be given by a) 0.707 hl b) 1.414hl c) hl d) None of the listed
Last Answer : a) 0.707 hl
Description : What is the approximate nominal diameter for coarse threads? a. d = 1.136 dc b. d = 1.59 dc c. d = 1.19 dc d. d = 0.5 dc
Last Answer : c. d = 1.19 dc
Description : Standard coarse threads are equally strong in failure by shear and failure by tension, if the height of nut is (A) h = 0.4 d (B) h = 0.6 d (C) h = 0.5 d (D) h = d
Last Answer : (A) h = 0.4 d
Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc
Last Answer : (A) h = 0.5 dc
Description : When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc
Last Answer : (B) h = 0.25 dc
Description : The ratio of endurance limit in shear to the endurance limit in flexure is (a) 0.25 (b) 0.40 (c) 0.55 (d) 0.70
Last Answer : (c) 0.55
Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65
Last Answer : (c) 0.50
Description : The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld
Last Answer : (b) Throat of weld
Description : In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld
Last Answer : (c) 2 × Throat of weld
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm
Last Answer : a) 27mm
Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed
Last Answer : c) 41666.7N
Description : Calculate the shaft diameter on rigidity basis if torsional moment is 196000N-mm, length of shaft is 1000mm. Permissible angle of twist per meter is 0.5’ and take G=79300N/mm2. a) None of the listed b) 41.2mm c) 35.8mm d) 38.8mm
Last Answer : b) 41.2mm
Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a =σ e [1-(σ m /σ u )x], where σ e is the fatigue limit for completely reversed loading. The value of x for Gerber line is equal to _________ a) 1 b) 2 c) 0.5 d) -1
Last Answer : b) 2
Description : The relationship between the alternating stress and mean stress is given by the following equation: σ a = σ e [1-(σ m /σ u ) x ]. The value of x for Goodman line is equal to _________ a) 1 b) 2 c) 0.5 d) -1
Last Answer : a) 1
Description : Calculate fatigue stress concentration factor, when theoretical stress concentration factor is 1.62 and notch sensitivity is equal to 0.9 a. 1.558 b. 3.358 c. 1.162 d. None of the above
Last Answer : a. 1.558
Description : Which of the following conditions is true for repeated stress? 1. σ m = 0 2. σ m = σ max / 2 3. σ m = σ a 4. σ min = 0 5. σ min = - σ max 6. σ a = σ max / 2 where σ m = mean ... amplitude a. condition 2 and 3 b. condition 1, 3 and 5 c. condition 2, 4, and 6 d. condition 3,4, 5 and 6
Last Answer : c. condition 2, 4, and 6
Description : Maximum principal stress is equal to (a) (σx + σy)/2 + [ (σx –σy) 2 + τ 2 ] 0.5 (b) (σx + σy)/2 + 0.5 [ (σx –σy) 2 + τ 2 ] 0.5 (c) (σx + σy)/2 + 0.5 [ (σx –σy) 2 + 4τ 2 ] 0.5 (d) None
Last Answer : (c) (σx + σy)/2 + 0.5 [ (σx –σy) 2 + 4τ 2 ] 0.5
Description : The angle between a principal plane and a plane of maximum shear is a. 15 0 b. 45 0 c. 75 0 d. None
Last Answer : b. 45 0
Description : The angle between a principal plane and a plane of maximum shear is a. 30 0 b. 60 0 c. 90 0 d. None
Last Answer : d. None
Description : All the maximum shear stresses are at an angle of (a)45 0 (b) 90 0 (c) 135 0 (d) None
Last Answer : (b) 90 0
Description : All the principal strains are at an angle of (a) 45 0 (b) 90 0 (c) 135 0 (d) None
Description : All the principal stresses are at an angle of (a)90 0 (b) 45 0 (c) 135 0 (d) None
Last Answer : (a)90 0
Description : All the principal stresses are at an angle of (a) 45 0 (b) 60 0 (c) 75 0 (d) None
Last Answer : (d) None
Description : The magnitude of maximum shear stress is (a) ± (1/2)[ ((σx –σy) 2 + 4 τ 2 )) 0.5 ] (b) ± (1/2)[ (1/2)((σx –σy) 2 + 4 τ 2 )) 0.5 ] (c) ± (1/2)[ ((1/2)(σx –σy) 2 + 4 τ 2 )) 0.5 ] (d) None
Last Answer : (a) ± (1/2)[ ((σx –σy) 2 + 4 τ 2 )) 0.5 ]
Description : The magnitude of principal stresses due to complex stresses is (a) (1/2)[ (σ x + σ y ) ± ((σ x –σ y ) 2 + 4 τ 2 )) 0.5 ] (b) (1/2)[ (σx + σy) ± (1/2)((σx –σy) 2 + 4 τ 2 )) 0.5 ] (c) (1/2)[ (σx + σy) ± ((1/2)(σx –σy) 2 + 4 τ 2 )) 0.5 ]
Last Answer : (a) (1/2)[ (σ x + σ y ) ± ((σ x –σ y ) 2 + 4 τ 2 )) 0.5 ]