Compared with Babbitt, bronze (A) Is cheaper (B) Has high strength (C) Can withstand high pressure (D) Has all three characteristics

Compared with Babbitt, bronze

(A) Is cheaper

(B) Has high strength

(C) Can withstand high pressure

(D) Has all three characteristics
by

1 Answer

Answer :

(D) Has all three characteristics
by

Related questions

Babbitt lining is used on brass/bronze bearings to increase the (A) Antifriction properties (B) Compressive strength (C) Bearing resistance

Description : Babbitt lining is used on brass/bronze bearings to increase the (A) Antifriction properties (B) Compressive strength (C) Bearing resistance

Last Answer : Option D

The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Description : The endurance or fatigue limit is defined as the maximum value of the stress which a polished standard specimen can withstand without failure, for infinite number of cycles, when subjected to (a) static load (b) dynamic load (c) static as well as dynamic load (d) completely reversed load

Last Answer : (d) completely reversed load

Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above

Description : Which of the following is (are) true? (A) Cast iron has poor tensile strength compared to steel (B) Failure of cast iron flywheel is sudden and total (C) Machinability of cast iron flywheel is poor compared to steel flywheel (D) All of the above

Last Answer : (D) All of the above

Bronze is an alloy of A. Copper and zinc B. Copper and tin C. Copper, tin and zinc D. None of these

Description : Bronze is an alloy of A. Copper and zinc B. Copper and tin C. Copper, tin and zinc D. None of these

Last Answer : B. Copper and tin

Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is generated by the rotation of the journal. [IES-1998] (a) Both A and R are individually true and R is the correct explanation of A (b) Both A and R are individually true but R is not the correct explanation of A (c) A is true but R is false (d) A is false but R is true

Description : Assertion (A): Hydrostatic lubrication is more advantageous when compared to hydrodynamic lubrication during starting and stopping the journal in its bearing. Reason (R): In hydrodynamic lubrication, the fluid film pressure is ... (c) A is true but R is false (d) A is false but R is true

Last Answer : (b) Both A and R are individually true but R is not the correct explanation of A

The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Description : The rolling contact bearings as compared to sliding contact bearings have (a) small overall dimensions (b) accuracy of shaft alignment (c) low starting and low running friction except at very high speeds (d) all the mentioned

Last Answer : (d) all the mentioned

Dielectric strength of a material is (A) Its energy storage capacity (B) A magnetic property (C) Its capacity to resist the flow of current(D) Its capacity to withstand high voltage

Description : Dielectric strength of a material is (A) Its energy storage capacity (B) A magnetic property (C) Its capacity to resist the flow of current (D) Its capacity to withstand high voltage

Last Answer : (D) Its capacity to withstand high voltage

A flywheel is made of 1. cast iron 2. high strength steels 3. graphic fiber reinforced polymer 4. any one of the above materials

Description : A flywheel is made of 1. cast iron 2. high strength steels 3. graphic fiber reinforced polymer 4. any one of the above materials

Last Answer : 4. any one of the above materials

Flywheel are generally made from (A) Cast Iron (B) High strength steel (C) Ceramics (D) All of the above

Description : Flywheel are generally made from (A) Cast Iron (B) High strength steel (C) Ceramics (D) All of the above

Last Answer : (D) All of the above

Lap welded joints used in circumferential joints because of ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements

Description : Lap welded joints used in circumferential joints because of ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements

Last Answer : ii. Low strength requirements

Why are butt welded joints longitudinal joints ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements iv. None

Description : Why are butt welded joints longitudinal joints ? i. High strength requirements ii. Low strength requirements iii. Low as well as high strength requirements iv. None

Last Answer : i. High strength requirements

Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above

Description : Threads used in screw fasteners are ______ a. having high strength b. having low efficiency c. single start type d. all of the above

Last Answer : d. all of the above

The following element can't impart high strength at elevated temperature A. Manganese B. Magnesium C. Nickel D. Silicon

Description : The following element can't impart high strength at elevated temperature A. Manganese B. Magnesium C. Nickel D. Silicon

Last Answer : B. Magnesium

Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False

Description : Cylindrical roller bearing has a lower load capacity as compared to deep groove ball bearing. (a) True (b) False

Last Answer : (b) False

As compared with oil with VI=80, a lubricating oil with VI=90 (A) Has more viscosity (B) Has less viscosity (C) Has more rate of change of viscosity with respect to temperature (D) Has less rate of change of viscosity with respect to temperature

Description : As compared with oil with VI=80, a lubricating oil with VI=90 (A) Has more viscosity (B) Has less viscosity (C) Has more rate of change of viscosity with respect to temperature (D) Has less rate of change of viscosity with respect to temperature

Last Answer : (D) Has less rate of change of viscosity with respect to temperature

Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False

Description : Cylindrical load bearing has lower load capacity as compared to deep groove ball bearing. a) True b) False

Last Answer : b) False

The yield point in static loading is ............... as compared to fatigue loading. (a) higher (b) lower (c) same

Description : The yield point in static loading is ............... as compared to fatigue loading. (a) higher (b) lower (c) same

Last Answer : (a) higher

Distortion energy theory is slightly liberal as compared to maximum shear stress theory. a) True b) False

Description : Distortion energy theory is slightly liberal as compared to maximum shear stress theory. a) True b) False

Last Answer : a) True

The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

Description : The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

Last Answer : D) Endurance limit

The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Description : The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Last Answer : Option A

What Properties Are Needed To Be Considered For Application Calling For Following Requirements? I) Rigidity. Ii) Strength Of No Plastic Deformation Under Static Load. Iii) Strength To Withstand Overload Without Fracture.

Description : What Properties Are Needed To Be Considered For Application Calling For Following Requirements? I) Rigidity. Ii) Strength Of No Plastic Deformation Under Static Load. Iii) Strength To Withstand Overload Without Fracture.

Last Answer : i) Reliability – elastic modulus and yield strength. ii) Strength (for no plastic deformation under static loading) – yield point. iii) Strength (overload) – Toughness and impact resistance. iv) Wear resistance – Hardness. v) Reliability and safety – Endurance limit and yield.

_____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Last Answer : (b) Pitting

Welded structures with respect to riveted joint is a. Weakened in tension b. Strengthened in tension c. No change in tension strength d. None

Description : Welded structures with respect to riveted joint is a. Weakened in tension b. Strengthened in tension c. No change in tension strength d. None

Last Answer : c. No change in tension strength

The strength of a welded joint with respect to a riveted joint is a. Greater b. Smaller c. Equal d. None

Description : The strength of a welded joint with respect to a riveted joint is a. Greater b. Smaller c. Equal d. None

Last Answer : a. Greater

Welded joint strength increases due to annealing by i. 6% ii. 10% iii. 14% iv. None

Description : Welded joint strength increases due to annealing by i. 6% ii. 10% iii. 14% iv. None

Last Answer : i. 6%

Strength of a welded joint increases by radio graphing by i. 10 % ii. 12% iii. 15% iv. None

Description : Strength of a welded joint increases by radio graphing by i. 10 % ii. 12% iii. 15% iv. None

Last Answer : ii. 12%

Testing the ultimate strength of the weld falls in nondestructive examination. a) True b) False

Description : Testing the ultimate strength of the weld falls in nondestructive examination. a) True b) False

Last Answer : b) False

Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False

Description : Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False

Last Answer : b) False

When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is equal to the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (A) h = 0.5 dc

When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Description : When the shear strength of nut is half the tensile strength of bolt, the height of nut (h) should be (A) h = 0.5 dc (B) h = 0.25 dc (C) h = 0.75 dc (D) h = dc

Last Answer : (B) h = 0.25 dc

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : The parallel fillet welded joint is designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (d) shear strength

he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (a) tensile strength

Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Last Answer : b) Distortion energy theory

The strength of hollow shaft is more than the strength of solid shaft of same weight. a) True b) False

Description : The strength of hollow shaft is more than the strength of solid shaft of same weight. a) True b) False

Last Answer : a) True

If yielding strength=400N/mm2, the find the permissible shear stress according to ASME standards. a) 72 N/mm2 b) 76 N/mm2 c) 268 N/mm2 d) 422 N/mm2

Description : If yielding strength=400N/mm2, the find the permissible shear stress according to ASME standards. a) 72 N/mm2 b) 76 N/mm2 c) 268 N/mm2 d) 422 N/mm2

Last Answer : a) 72 N/mm2

According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

The strength of hollow shaft is more than the strength of solid shaft of same weight. a) True b) False

Description : The strength of hollow shaft is more than the strength of solid shaft of same weight. a) True b) False

Last Answer : a) True

According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Description : According to the ASME code, maximum allowable shear stress is taken as X% of yield strength or Y% of ultimate strength. a) X=30 Y=18 b) X=30 Y=30 c) X=18 Y=18 d) X=18 Y=30

Last Answer : a) X=30 Y=18

The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above

Description : The keyway, (A) Reduces strength of shaft (B) Reduces rigidity of shaft (C) Increases stress concentration (D) All of above

Last Answer : (D) All of above

The shafts will have same strength on the basis of torsional rigidity, if (A) Diameter and length of both shafts is same (B) Material of both shafts is same (C) Angle of twist for both shafts is same (D) All of above conditions are satisfied

Description : The shafts will have same strength on the basis of torsional rigidity, if (A) Diameter and length of both shafts is same (B) Material of both shafts is same (C) Angle of twist for both shafts is same (D) All of above conditions are satisfied

Last Answer : (D) All of above conditions are satisfied

Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Description : Among maximum shear stress theory and distortion energy theory, which gives the higher value shear yield strength? a) Maximum shear stress theory b) Distortion energy theory c) Both give equal values d) Vary from material to material

Last Answer : b) Distortion energy theory

In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Description : In S-N diagram, the graph plotted between fatigue strength and number of stress cycles becomes horizontal for which type of materials? a. Ferrous materials b. Non-ferrous materials c. Both a. and b. d. None of the above

Last Answer : a. Ferrous materials

Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Description : Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Last Answer : b. Soderberg line

In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Description : In a ductile material, the strength are (a)Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Last Answer : (a)Firstly Ultimate >yield > elastic limit

In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Description : In a brittle material, the strength are (a) Firstly Ultimate >yield > elastic limit (b) Secondly Ultimate > yield =elastic limit (c) Thirdly Ultimate=yield=elastic limit (d) None

Last Answer : (c) Thirdly Ultimate=yield=elastic limit

Theories of elastic failure is the (a) Firstly analysis of the various failures (b) Secondly analysis of the strength of a material (c) Both (a) & (b) (d) None

Description : Theories of elastic failure is the (a) Firstly analysis of the various failures (b) Secondly analysis of the strength of a material (c) Both (a) & (b) (d) None

Last Answer : (c) Both (a) & (b)

The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Description : The ability of a material to resist plastic deformation known as _____________ a) Tensile strength b) Yield strength c) Modulus of elasticity d) Impact strength

Last Answer : b) Yield strength