For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus-Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of (A) 1 (B) 1.74 (C) 6.1 (D) 37

For turbulent flow in a tube, the heat transfer co-efficient is obtained

from the Dittus-Boelter correlation. If the tube diameter is halved and the

flow rate is doubled, then the heat transfer co-efficient will change by a

factor of

(A) 1

(B) 1.74

(C) 6.1

(D) 37

by

1 Answer

Answer :

(C) 6.1

by

Related questions

Dittus-Boelter equation used for the determination of heat transfer co￾efficient is valid (A) For fluids in laminar flow (B) For fluids in turbulent flow (C) When Grashoff number is very important (D) For liquid metals

Description : Dittus-Boelter equation used for the determination of heat transfer co￾efficient is valid (A) For fluids in laminar flow (B) For fluids in turbulent flow (C) When Grashoff number is very important (D) For liquid metals

Last Answer : (B) For fluids in turbulent flow

The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient varies with the pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Description : The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient ... pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Last Answer : (B) D-0.2

Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

Which of the following forced convection heat transfer equation accounts for the liquid viscosity effect for viscous liquids? (A) Dittus-Boelter equation (B) Sieder-Tate equation (C) Nusselt equation (D) None of these

Description : Which of the following forced convection heat transfer equation accounts for the liquid viscosity effect for viscous liquids? (A) Dittus-Boelter equation (B) Sieder-Tate equation (C) Nusselt equation (D) None of these

Last Answer : (B) Sieder-Tate equation

The Dittus-Boelter equation for convective heat transfer [(i.e. h = 0.023 (K/D) (Re) 0.8 (Pr) 0.4 ] cannot be used for (A) Low Reynold's number (B) Very low Grashoff number (C) Molten metals (D) All (A), (B) and (C)

Description : The Dittus-Boelter equation for convective heat transfer [(i.e. h = 0.023 (K/D) (Re) 0.8 (Pr) 0.4 ] cannot be used for (A) Low Reynold's number (B) Very low Grashoff number (C) Molten metals (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Description : The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Last Answer : (B) 4 0.8

A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Description : A fluid is flowing inside the inner tube of a double pipe heat exchanger with diameter 'd'. For a fixed mass flow rate, the tube side heat transfer co￾efficient for turbulent flow conditions is proportional to (A) d 0.8 (B) d -0.2 (C) d -1 (D) d -1.8

Last Answer : (B) d -0.2

Dittus-Boelter equation cannot be used for molten metals mainly due to its very low (A) Prandtl number (B) Grashoff number (C) Thermal conductivity (D) Viscosity

Description : Dittus-Boelter equation cannot be used for molten metals mainly due to its very low (A) Prandtl number (B) Grashoff number (C) Thermal conductivity (D) Viscosity

Last Answer : (A) Prandtl number

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

If the velocity of flow as well as the diameter of the flowing pipe are respectively doubled through a pipe system in use since long, the head loss will thereafter be (a) Halved (b) Doubled (c) Increased 4 times (d) No change

Description : If the velocity of flow as well as the diameter of the flowing pipe are respectively doubled through a pipe system in use since long, the head loss will thereafter be (a) Halved (b) Doubled (c) Increased 4 times (d) No change

Last Answer : (b) Doubled

Overall heat transfer co-efficient of a particular tube is U1 . If the same tube with some dirt deposited on either side has coefficient U2 , then (A) U1 = U2 (B) U2 > U1 (C) U1 > U2 (D) U1 = dirt factor - U2

Description : Overall heat transfer co-efficient of a particular tube is U1 . If the same tube with some dirt deposited on either side has coefficient U2 , then (A) U1 = U2 (B) U2 > U1 (C) U1 > U2 (D) U1 = dirt factor - U2

Last Answer : (A) U1 = U2

Maximum heat transfer rate is obtained in __________ flow. (A) Laminar (B) Turbulent (C) Creeping (D) Transition region

Description : Maximum heat transfer rate is obtained in __________ flow. (A) Laminar (B) Turbulent (C) Creeping (D) Transition region

Last Answer : (B) Turbulent

Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient for the cooling water, whether on shell side or tube side is the same. The best arrangement is (A) Vertical heat exchanger with steam on tube side (B) Vertical heat exchanger with steam on shell side (C) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Description : Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient ... ) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Last Answer : (B) Vertical heat exchanger with steam on shell side

Maximum heat transfer rate is achieved in __________ flow. (A) Co-current (B) Counter-current (C) Turbulent (D) Laminar

Description : Maximum heat transfer rate is achieved in __________ flow. (A) Co-current (B) Counter-current (C) Turbulent (D) Laminar

Last Answer : (C) Turbulen

Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Description : Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Last Answer : (C) Increase the shell side heat transfer co-efficient

For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1(B) 0.794 h1(C) 0.574 h1(D) 1.741 h1

Description : For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1 (B) 0.794 h1 (C) 0.574 h1 (D) 1.741 h1

Last Answer : (B) 0.794 h1

The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2.K. The fouling factor after one year ofoperation is found to be hd0 = 2000 W/m2.K. The overall heat transfer co￾efficient at this time is(A) 1200 W/m2.K(B) 894 W/m2.K(C) 333 W/m2.K(D) 287 W/m2.K

Description : The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2 .K. The fouling factor after one year of operation is found to be hd0 = 2000 W/m2 .K. The overall heat transfer co￾efficient ... 1200 W/m2 .K (B) 894 W/m2 .K (C) 333 W/m2 .K (D) 287 W/m2 .K

Last Answer : (C) 333 W/m2 .K

Out of the following four assumptions used in the derivation of theequation for LMTD[LMTD = (∆t1- ∆t2)/ln(∆t1/∆t2)], which one is subject to the largest deviationin practice ?(A) Constant overall heat transfer co-efficient.(B) Constant rate of fluid flow(C) Constant specific heat(D) No partial phase change in the system

Description : Out of the following four assumptions used in the derivation of theequation for LMTD [LMTD = (∆t1 - ∆t2 )/ln(∆t1 /∆t2 )], which one is subject to the largest deviation in practice ? (A) Constant ... (B) Constant rate of fluid flow (C) Constant specific heat (D) No partial phase change in the system

Last Answer : (B) Constant rate of fluid flow

Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Description : Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Last Answer : (D) All (A) (B) and (C)

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

If the length of a simple pendulum is halved then its period of oscillation is - (1) doubled (2) halved (3) increased by a factor √ 2 (4) decreased by a factor √ 2

Description : If the length of a simple pendulum is halved then its period of oscillation is - (1) doubled (2) halved (3) increased by a factor √ 2 (4) decreased by a factor √ 2

Last Answer : (4) decreased by a factor √ 2

If the length of a simple pendulum is halved then its period of oscillation is (1) doubled (2) halved (3) increased by a factor 2 (4) decreased by a factor 2

Description : If the length of a simple pendulum is halved then its period of oscillation is (1) doubled (2) halved (3) increased by a factor root 2 (4) decreased by a factor root  2

Last Answer : decreased by a factor root 2

All analogy equations connecting friction factor and heat transfer co￾efficient apply only to (A) Wall or skin friction (B) Form friction (C) Both (A) and (B) (D) Turbulent flow

Description : All analogy equations connecting friction factor and heat transfer co￾efficient apply only to (A) Wall or skin friction (B) Form friction (C) Both (A) and (B) (D) Turbulent flow

Last Answer : (A) Wall or skin friction

Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Description : Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Last Answer : (C) Heat transfer co-efficient

. In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Description : . In a shell and tube heat exchanger, the tube side heat transfer co￾efficient just at the entrance of the tube is (A) Infinity (B) Zero (C) Same as average heat transfer co-efficient for tube side (D) None of these

Last Answer : (A) Infinity

In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

The advantage of using a 1 - 2 shell and tube heat exchanger over a 1 - 1 shell and tube heat exchanger is (A) Lower tube side pressure drop (B) Lower shell side pressure drop (C) Higher tube side heat transfer co-efficient (D) Higher shell side heat transfer co-efficient

Description : The advantage of using a 1 - 2 shell and tube heat exchanger over a 1 - 1 shell and tube heat exchanger is (A) Lower tube side pressure drop (B) Lower shell side pressure drop (C) Higher tube side heat transfer co-efficient (D) Higher shell side heat transfer co-efficient

Last Answer : (C) Higher tube side heat transfer co-efficient

Multipass heat exchangers are used (A) Because of simplicity of fabrication (B) For low heat load (C) To obtain higher heat transfer co-efficient and shorter tube (D) To reduce the pressure drop

Description : Multipass heat exchangers are used (A) Because of simplicity of fabrication (B) For low heat load (C) To obtain higher heat transfer co-efficient and shorter tube (D) To reduce the pressure drop

Last Answer : (C) To obtain higher heat transfer co-efficient and shorter tube

Extremely large or small volumes of fluids are generally best routed through the shell side of a shell and tube heat exchanger, because of the (A) Less corrosion problems (B) Flexibility possible in the baffle arrangement (C) Low pressure drop (D) High heat transfer co-efficient

Description : Extremely large or small volumes of fluids are generally best routed through the shell side of a shell and tube heat exchanger, because of the (A) Less corrosion problems (B) Flexibility possible in the baffle arrangement (C) Low pressure drop (D) High heat transfer co-efficient

Last Answer : (B) Flexibility possible in the baffle arrangement

In a shell and tube heat exchanger, floating head is used for (A) Large temperature differentials (B) High heat transfer co-efficient (C) Low pressure drop (D) Less corrosion of tubes

Description : In a shell and tube heat exchanger, floating head is used for (A) Large temperature differentials (B) High heat transfer co-efficient (C) Low pressure drop (D) Less corrosion of tubes

Last Answer : (A) Large temperature differentials

When the current flow in a power transmission line is halved, the power loss _____________. A. is halved B. is doubled C. is divided by four D. remains the same

Description : When the current flow in a power transmission line is halved, the power loss _____________. A. is halved B. is doubled C. is divided by four D. remains the same

Last Answer : Answer: C

When the current flow through a power transmission line is doubled, the power loss _____________. A. is halved B. is doubled C. is quadrupled D. remains the same

Description : When the current flow through a power transmission line is doubled, the power loss _____________. A. is halved B. is doubled C. is quadrupled D. remains the same

Last Answer : Answer: C

If the antenna current is doubled, the field strength at a particular position is A. doubled B. halved C. multiplied by a factor of four D. divided by a factor of four

Description : If the antenna current is doubled, the field strength at a particular position is A. doubled B. halved C. multiplied by a factor of four D. divided by a factor of four

Last Answer : A. doubled

In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Description : In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Last Answer : (B) Flows outside the tubes

If radius of a batch basket centrifuge is halved & the r.p.m. is doubled, then the (A) Linear speed of the basket is doubled (B) Linear speed of the basket is halved (C) Centrifugal force is doubled (D) Capacity of centrifuge is increased

Description : If radius of a batch basket centrifuge is halved & the r.p.m. is doubled, then the (A) Linear speed of the basket is doubled (B) Linear speed of the basket is halved (C) Centrifugal force is doubled (D) Capacity of centrifuge is increased

Last Answer : (C) Centrifugal force is doubled

In a reversible chemical reaction having two reactants in equilibrium, if the concentration of the reactants are doubled, then the equilibrium constant will (A) Remain the same (B) Be halved (C) Also be doubled (D) Become one fourth

Description : In a reversible chemical reaction having two reactants in equilibrium, if the concentration of the reactants are doubled, then the equilibrium constant will (A) Remain the same (B) Be halved (C) Also be doubled (D) Become one fourth

Last Answer : (A) Remain the same

Two substances are in equilibrium in a reversible chemical reaction. If the concentration of each substance is doubled, then the value of the equilibrium constant will be (A) Same (B) Doubled (C) Halved (D) One fourth of its original value

Description : Two substances are in equilibrium in a reversible chemical reaction. If the concentration of each substance is doubled, then the value of the equilibrium constant will be (A) Same (B) Doubled (C) Halved (D) One fourth of its original value

Last Answer : (A) Same

Assuming flow to be laminar, if the diameter of the pipe is halved, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Be quadrupled

Description : Assuming flow to be laminar, if the diameter of the pipe is halved, then the pressure drop will (A) Increase (B) Decrease (C) Remain same (D) Be quadrupled

Last Answer : (A) Increase

Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low interfacial tension (C) When Henry's law constant is very small, then the mass transfer rate is controlled by the gas film resistance (D) Taylor-Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Description : Pick out the wrong statement. (A) Mechanical agitation is required, if the system has low interfacial tension (B) Sieve tray towers are generally used for systems having low ... Prandtl analogy for heat and mass transfer considers the transfer through both laminar and turbulent layers

Last Answer : (A) Mechanical agitation is required, if the system has low interfacial tension

Heat transfer co-efficient equation for forced convection, Nu = 0.023 Re 0.8 . Pr n , is not valid, if the value of (A) n = 0.4 is used for heating (B) n = 0.3 is used for cooling (C) Reynolds number for the flow involved is > 10000 (D) Reynolds number for the flow involved is < 2100

Description : Heat transfer co-efficient equation for forced convection, Nu = 0.023 Re 0.8 . Pr n , is not valid, if the value of (A) n = 0.4 is used for heating (B) n = 0.3 is used for cooling (C) Reynolds number for the flow involved is > 10000 (D) Reynolds number for the flow involved is < 2100

Last Answer : (D) Reynolds number for the flow involved is < 2100

Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface). (A) U1 - U2 (B) 1/U1 - 1/U2 (C) 1/U2 - 1/U1 (D) U2 - U1

Description : Fouling factor for a heat exchanger is given by (where, U1 = heat transfer co-efficient of dirty surface U2 = heat transfer co-efficient of clean surface). (A) U1 - U2 (B) 1/U1 - 1/U2 (C) 1/U2 - 1/U1 (D) U2 - U1

Last Answer : (B) 1/U1 - 1/U2

In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation will (A) Increase (B) Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Description : In a co-current double pipe heat exchanger used for condensing saturated steam over the inner tube, if the entrance and exit conditions of the coolant are interchanged, then the rate of condensation ... Decrease (C) Remain unchanged (D) Either increase or decrease; depends on the coolant flow rate

Last Answer : (C) Remain unchanged

A straight line is obtained on plotting reciprocal of filtration rate vs. the volume of filtrate for __________ flow of filtrate. (A) Compressible cakes and laminar (B) Incompressible cake and laminar (C) Compressible cake and turbulent (D) Incompressible cake and turbulent

Description : A straight line is obtained on plotting reciprocal of filtration rate vs. the volume of filtrate for __________ flow of filtrate. (A) Compressible cakes and laminar (B) Incompressible cake and laminar (C) Compressible cake and turbulent (D) Incompressible cake and turbulent

Last Answer : (B) Incompressible cake and laminar

In a fully turbulent flow (Re > 10 5 ) in a pipe of diameter 'd', for a constant pressure gradient, the dependence of volumetric flow rate of an incompressible fluid is (A) d(B) d2(C) d2.5(D) d

Description : In a fully turbulent flow (Re > 10 5 ) in a pipe of diameter 'd', for a constant pressure gradient, the dependence of volumetric flow rate of an incompressible fluid is (A) d (B) d 2 (C) d 2.5 (D) d

Last Answer : (C) d 2.5

If in a cylinder, radius is doubled and height is halved, then find its curved surface area. -Maths 9th

Description : If in a cylinder, radius is doubled and height is halved, then find its curved surface area. -Maths 9th

Last Answer : Let r and h be radius and height of the cyclinder, then C.S.A. = 2πrh Now, radius is doubled and height is halved. ∴ New radius = 2r and new height = h / 2 New C.S.A. = 2π × 2r × h / 2 = 2πrh .

A spherical ball is divided into two equal halves. If the curved surface area of each half is 56.57 cm?, find the volume of the spherical ball.11531/cylinder-radius-halved-and-height-doubled-then-find-volume-with-respect-original-volume -Maths 9th

Description : A spherical ball is divided into two equal halves. If the curved surface area of each half is 56.57 cm?, find the volume of the spherical ball.11531/cylinder-radius-halved-and-height-doubled-then-find-volume-with-respect-original-volume -Maths 9th

Last Answer : since curved surface of half of the spherical ball = 56.57 cm2 ∴ 2πr2 = 56.57 ⇒ r2 = 56.57 / 2 × 3.14 = 9 ⇒ r = 3 cm Now, volume of spherical ball = 4 / 3 πr3 = 4 / 3 × 3.14 × 3 × 3 × 3 = 113.04 cm3

If in a cylinder, radius is doubled and height is halved, then find its curved surface area. -Maths 9th

Description : If in a cylinder, radius is doubled and height is halved, then find its curved surface area. -Maths 9th

Last Answer : Let r and h be radius and height of the cyclinder, then C.S.A. = 2πrh Now, radius is doubled and height is halved. ∴ New radius = 2r and new height = h / 2 New C.S.A. = 2π × 2r × h / 2 = 2πrh .

A spherical ball is divided into two equal halves. If the curved surface area of each half is 56.57 cm?, find the volume of the spherical ball.11531/cylinder-radius-halved-and-height-doubled-then-find-volume-with-respect-original-volume -Maths 9th

Description : A spherical ball is divided into two equal halves. If the curved surface area of each half is 56.57 cm?, find the volume of the spherical ball.11531/cylinder-radius-halved-and-height-doubled-then-find-volume-with-respect-original-volume -Maths 9th

Last Answer : since curved surface of half of the spherical ball = 56.57 cm2 ∴ 2πr2 = 56.57 ⇒ r2 = 56.57 / 2 × 3.14 = 9 ⇒ r = 3 cm Now, volume of spherical ball = 4 / 3 πr3 = 4 / 3 × 3.14 × 3 × 3 × 3 = 113.04 cm3

In a cylinder, radius is doubled and height is halved, then curved surface area will be -Maths 9th

Description : In a cylinder, radius is doubled and height is halved, then curved surface area will be -Maths 9th

Last Answer : The curved surface area will remain same. So, there is no change in the curved surface area of cylinder . Hence the curved surface area will remain same.