Out of the following four assumptions used in the derivation of theequation for LMTD[LMTD = (∆t1- ∆t2)/ln(∆t1/∆t2)], which one is subject to the largest deviationin practice ?(A) Constant overall heat transfer co-efficient.(B) Constant rate of fluid flow(C) Constant specific heat(D) No partial phase change in the system

Out of the following four assumptions used in the derivation of theequation for LMTD
[LMTD = (∆t1
- ∆t2
)/ln(∆t1
/∆t2
)], which one is subject to the largest deviation
in practice ?
(A) Constant overall heat transfer co-efficient.
(B) Constant rate of fluid flow
(C) Constant specific heat
(D) No partial phase change in the system
by

1 Answer

Answer :

(B) Constant rate of fluid flow
by

Related questions

Log mean temperature difference (LMTD) cannot be used, if (A) Heat transfer co-efficient over the entire heat exchanger is not constant (B) There exists an unsteady state (C) The heat capacity is not constant and there is a phase change (D) None of these

Description : Log mean temperature difference (LMTD) cannot be used, if (A) Heat transfer co-efficient over the entire heat exchanger is not constant (B) There exists an unsteady state (C) The heat capacity is not constant and there is a phase change (D) None of these

Last Answer : (D) None of these

Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for counter flow and parallel flow can be theoretically same when any one of the fluids (hot or cold fluid) passes through the heat exchanger at constant temperature (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs (D) Phase change in case of a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Description : Pick out the wrong statement. (A) The controlling resistance in case of heating of air by condensing steam is in the air film (B) The log mean temperature difference (LMTD) for ... a pure fluid at a given pressure from liquid to vapor or vice-versa occurs at saturation temperature

Last Answer : (C) In case of a 1 - 2 shell and tube heat exchanger, the LMTD correction factor value increases sharply, when a temperature cross occurs

Bernoulli's equation for fluid flow is derived following certain assumptions. Out of the assumptions listed below, which set of assumptions is used in derivation of Bernoulli's equation? A. Fluid flow is frictionless & irrotational. B. Fluid flow is steady. C. Fluid flow is uniform & turbulent. D. Fluid is compressible. E. Fluid is incompressible. (A) A, C, D (B) B, D, E (C) A, B, E (D) A, D, E

Description : Bernoulli's equation for fluid flow is derived following certain assumptions. Out of the assumptions listed below, which set of assumptions is used in derivation of Bernoulli's equation? A. Fluid flow is frictionless & irrotational. B. Fluid flow is ... A, C, D (B) B, D, E (C) A, B, E (D) A, D, E

Last Answer : (C) A, B, E

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1(B) 0.794 h1(C) 0.574 h1(D) 1.741 h1

Description : For a laminar flow of fluid in a circular tube, 'h1 ' is the convective heat transfer co-efficient at velocity 'V1 '. If the velocity is reduced by half and assuming the fluid properties are constant, the new convective heat transfer co-efficient is (A) 1.26 h1 (B) 0.794 h1 (C) 0.574 h1 (D) 1.741 h1

Last Answer : (B) 0.794 h1

In a heat exchanger, the rate of heat transfer from the hot fluid to the cold fluid (A) Varies directly as the area and the LMTD (B) Directly proportional to LMTD and inversely proportional to the area (C) Varies as square of the area (D) None of these

Description : In a heat exchanger, the rate of heat transfer from the hot fluid to the cold fluid (A) Varies directly as the area and the LMTD (B) Directly proportional to LMTD and inversely proportional to the area (C) Varies as square of the area (D) None of these

Last Answer : (A) Varies directly as the area and the LMTD

For a heat exchanger, will the overall heat transfer coefficient increase along with an increase in LMTD (log mean temperature difference) around the unit?

Description : For a heat exchanger, will the overall heat transfer coefficient increase along with an increase in LMTD (log mean temperature difference) around the unit?

Last Answer : The overall heat transfer coefficient is generally weakly dependent on temperature. As the temperatures of the fluids change, the degree to which the overall heat transfer coefficient will be affected depends ... with temperature as I've noted and the U-value will decrease over time with fouling).

In counter flow compared to parallel flow, (A) LMTD is greater (B) Less surface area is required for a given heat transfer rate (C) Both (A) and (B) (D) More surface area is required for a given heat transfer rate

Description : In counter flow compared to parallel flow, (A) LMTD is greater (B) Less surface area is required for a given heat transfer rate (C) Both (A) and (B) (D) More surface area is required for a given heat transfer rate

Last Answer : (C) Both (A) and (B)

Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger, the shell pressure drop is maximum for orifice baffles (C) S.I. unit of fouling factor is Watt/m2 .°K (D) Longitudinal fins are used in extended surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Description : Pick out the wrong statement. (A) Superheated steam is preferably not used for process heating because of its low heat transfer film co-efficient (B) In a shell and tube heat exchanger ... surface heat exchangers, when the direction of fluid flow is parallel to the axis of the tube

Last Answer : (C) S.I. unit of fouling factor is Watt/m2 .°K

Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Description : Convective heat transfer co-efficient in case of fluid flowing in tubes is not affected by the tube length/diameter ratio, if the flow is in the __________ zone. (A) Laminar (B) Transition (C) Both 'a' & 'b' (D) Highly turbulent

Last Answer : (D) Highly turbulent

For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus-Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of (A) 1 (B) 1.74 (C) 6.1 (D) 37

Description : For turbulent flow in a tube, the heat transfer co-efficient is obtained from the Dittus-Boelter correlation. If the tube diameter is halved and the flow rate is doubled, then the heat transfer co-efficient will change by a factor of (A) 1 (B) 1.74 (C) 6.1 (D) 37

Last Answer : (C) 6.1

In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

Description : In a vapor-liquid contacting equipment, the overall gas phase mass transfer co-efficient (M.T.C), KG is related to individual co-efficients (KG and KL ) as (A) KG = 1/KG + m/KL (B) 1/KG = 1/KG + m/KL (C) 1/KG = 1/KL + m/KG (D) KG = 1/KL + m/KG

Last Answer : (B) 1/KG = 1/KG + m/KL

The molar excess Gibbs free energy, gE, for a binary liquid mixture at T and P is given by, (gE/RT) = A . x1. x2, where A is a constant. The corresponding equation for ln y1, where y1is the activity co-efficient of component 1, is (A) A . x22 (B) Ax1 (C) Ax2 (D) Ax12

Description : The molar excess Gibbs free energy, gE, for a binary liquid mixture at T and P is given by, (gE/RT) = A . x1. x2, where A is a constant. The corresponding equation for ln y1, where y1is the activity co-efficient of component 1, is (A) A . x22 (B) Ax1 (C) Ax2 (D) Ax12

Last Answer : (A) A . x22

Gibbs-Duhem equation relates composition in liquid phase and the __________ at constant temperature & pressure. (A) Fugacity (B) Partial pressure (C) Activity co-efficient (D) All (A), (B), and (C)

Description : Gibbs-Duhem equation relates composition in liquid phase and the __________ at constant temperature & pressure. (A) Fugacity (B) Partial pressure (C) Activity co-efficient (D) All (A), (B), and (C)

Last Answer : (D) All (A), (B), and (C)

LMTD for counter-flow and parallel flow heat exchanger will be the same, when the (A) Cold fluid is heated to a certain temperature by condensing steam (isothermal fluid) (B) Outlet temperature of both the hot and cold fluid are same (C) Outlet temperature of hot fluid is less than the outlet temperature of the cold fluid (D) None of these

Description : LMTD for counter-flow and parallel flow heat exchanger will be the same, when the (A) Cold fluid is heated to a certain temperature by condensing steam (isothermal fluid) (B) Outlet temperature of ... temperature of hot fluid is less than the outlet temperature of the cold fluid (D) None of these

Last Answer : (A) Cold fluid is heated to a certain temperature by condensing steam (isothermal fluid)

Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Description : Double pipe heat exchangers are preferably useful, when (A) High viscosity liquid is to be cooled (B) Requirement of heat transfer area is low (C) Overall heat transfer co-efficient is very high (D) A corrosive liquid is to be heated

Last Answer : (B) Requirement of heat transfer area is low

Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Description : Overall heat transfer co-efficient for cooling of hydrocarbons by water is about (A) 50 -100 Kcal/hr.m2 .°C (B) 50 -100 W/m2 .°K (C) 50 -100 BTU/hr. ft. 2°F (D) 1000 - 1500 BTU/hr. ft. 2°F

Last Answer : (C) 50 -100 BTU/hr. ft. 2°F

In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Description : If h1 = inner film co-efficient and /h2 = outer film co-efficient, then the overall heat transfer co-efficient is (A) Always less than h1 (B) Always between h1 and h2 (C) Always higher than h2 (D) Dependent on metal resistance

Last Answer : (B) Always between h1 and h2

Overall heat transfer co-efficient of a particular tube is U1 . If the same tube with some dirt deposited on either side has coefficient U2 , then (A) U1 = U2 (B) U2 > U1 (C) U1 > U2 (D) U1 = dirt factor - U2

Description : Overall heat transfer co-efficient of a particular tube is U1 . If the same tube with some dirt deposited on either side has coefficient U2 , then (A) U1 = U2 (B) U2 > U1 (C) U1 > U2 (D) U1 = dirt factor - U2

Last Answer : (A) U1 = U2

Which of the following has the lowest overall heat transfer co-efficient? (A) Dowtherm (B) Molten sodium (C) Water (D) Air

Description : Which of the following has the lowest overall heat transfer co-efficient? (A) Dowtherm (B) Molten sodium (C) Water (D) Air

Last Answer : (D) Air

The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2.K. The fouling factor after one year ofoperation is found to be hd0 = 2000 W/m2.K. The overall heat transfer co￾efficient at this time is(A) 1200 W/m2.K(B) 894 W/m2.K(C) 333 W/m2.K(D) 287 W/m2.K

Description : The overall heat transfer co-efficient for a shell and tube heat exchangerfor clean surfaces is U0 = 400 W/m2 .K. The fouling factor after one year of operation is found to be hd0 = 2000 W/m2 .K. The overall heat transfer co￾efficient ... 1200 W/m2 .K (B) 894 W/m2 .K (C) 333 W/m2 .K (D) 287 W/m2 .K

Last Answer : (C) 333 W/m2 .K

A thin, flat & square plate measuring 2 m × 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will remain constant at 30°C, if the convective heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200

Last Answer : (B) 100

Pick out the wrong statement. (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity(B) For an ideal mixed reactor at steady state, the exit stream has the samecomposition as fluid within the reactor and the space time is equivalent toholding time for constant density system(C) Plug flow reactor (PFR) is always smaller than mixed reactor for allpositive reaction orders for a particular duty(D) Reaction rate does not decrease appreciably as the reaction proceeds incase of an autocatalytic reaction

Description : Pick out the wrong statement. (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity(B) For an ideal ... D) Reaction rate does not decrease appreciably as the reaction proceeds in case of an autocatalytic reaction

Last Answer : (A) For a first order consecutive reaction, a tubular flow reactor as compared to a stirred tank reactor provides higher overall selectivity

Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Description : Heat transfer co-efficient (h) for a fluid flowing inside a clean pipe is given by h = 0.023 (K/D) (DVρ/µ) 0.8 (CP .µ/k) 0.4 . This is valid for the value of NRe equal to (A) < 2100 (B) 2100-4000 (C) > 4000 (D) > 10000

Last Answer : (D) > 10000

The wetted wall tower is used to determine (A) Individual mass transfer co-efficient (M.T.C.) in gaseous system (B) M.T.C. of individual components in a liquid-liquid system (C) M.T.C. of liquid in liquid-gas system (D) The overall M.T.C. of the system

Description : The wetted wall tower is used to determine (A) Individual mass transfer co-efficient (M.T.C.) in gaseous system (B) M.T.C. of individual components in a liquid-liquid system (C) M.T.C. of liquid in liquid-gas system (D) The overall M.T.C. of the system

Last Answer : (A) Individual mass transfer co-efficient (M.T.C.) in gaseous system

Controlling heat transfer film co-efficient is the one, which offers __________ resistance to heat transfer. (A) No (B) The least (C) The largest (D) Lower

Description : Controlling heat transfer film co-efficient is the one, which offers __________ resistance to heat transfer. (A) No (B) The least (C) The largest (D) Lower

Last Answer : (C) The largest

The outlet temperature of cooling water in a heat exchanger is generally not allowed to exceed above 50°C in industrial practice mainly to avoid (A) Its evaporation loss (B) Excessive corrosion (C) Uneconomic LMTD (D) Decrease in heat exchanger efficiency

Description : The outlet temperature of cooling water in a heat exchanger is generally not allowed to exceed above 50°C in industrial practice mainly to avoid (A) Its evaporation loss (B) Excessive corrosion (C) Uneconomic LMTD (D) Decrease in heat exchanger efficiency

Last Answer : (B) Excessive corrosion

In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Description : In an extended surface heat exchanger, fluid having lower co-efficient (A) Flows through the tube (B) Flows outside the tubes (C) Can flow either inside or outside the tubes (D) Should not be used as it gives very high pressure drop

Last Answer : (B) Flows outside the tubes

Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. (du/dy) n the value of 'n' for pseudoplastic and Dilatant fluid are < 1 and >1 respectively (C) Shear stress for Newtonian fluid is proportional to the rate of shear in the direction perpendicular to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Description : Pick out the wrong statement. (A) The shear stress at the pipe (dia = D, length = L) wall in case of laminar flow of Newtonian fluids is (D/4L). ∆p (B) In the equation, T. gc = k. ... to motion (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

Last Answer : (D) With increase in the Mach number >0.6, the drag co-efficient decreases in case of compressible fluids

The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient(B) Increasing the liquid film co-efficient(C) Increasing the total pressure(D) Decreasing the total pressure

Description : The overall mass transfer co-efficient for the absorption of SO2 in air with dilute NaOH solution can be increased substantially by (A) Increasing the gas film co-efficient (B) Increasing the liquid film co-efficient (C) Increasing the total pressure (D) Decreasing the total pressure

Last Answer : (A) Increasing the gas film co-efficient

What is the value of ln y (where y = activity co-efficient) for ideal gases? (A) Zero (B) Unity (C) Infinity (D) Negative

Description : What is the value of ln y (where y = activity co-efficient) for ideal gases? (A) Zero (B) Unity (C) Infinity (D) Negative

Last Answer : (A) Zero

The expression, nRT ln(P1/P2), is for the __________of an ideal gas. (A) Compressibility (B) Work done under adiabatic condition (C) Work done under isothermal condition (D) Co-efficient of thermal expansion

Description : The expression, nRT ln(P1/P2), is for the __________of an ideal gas. (A) Compressibility (B) Work done under adiabatic condition (C) Work done under isothermal condition (D) Co-efficient of thermal expansion

Last Answer : C) Work done under isothermal condition

In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 (C) Equal to the difference between hot and cold fluids inlet temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Description : In a 1-1 concurrent heat exchanger, if the tube side fluid outlet temperature is equal to the shell side fluid outlet temperature, then the LMTD is (A) ∞ (B) 0 ... temperature (D) Equal to the difference between hot fluid inlet temperature and cold fluid outlet temperature

Last Answer : (B) 0

In Fourier's law, the proportionality constant is called the (A) Heat transfer co-efficient (B) Thermal diffusivity (C) Thermal conductivity (D) Stefan-Boltzmann constant

Description : In Fourier's law, the proportionality constant is called the (A) Heat transfer co-efficient (B) Thermal diffusivity (C) Thermal conductivity (D) Stefan-Boltzmann constant

Last Answer : (C) Thermal conductivity

Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Description : Baffles in the shell side of a shell and tube heat exchanger (A) Increase the cross-section of the shell side liquid (B) Force the liquid to flow parallel to the bank (C) Increase the shell side heat transfer co-efficient (D) Decrease the shell side heat transfer co-efficient

Last Answer : (C) Increase the shell side heat transfer co-efficient

The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Description : The inside heat transfer co-efficient in case of turbulent flow of liquid in the tube side in a 1-2 shell and tube heat exchanger is increased by __________ times, when the number of tube passes is increased to 8. (A) 2 0.8 (B) 4 0.8 (C) 4 0.4 (D) 2 0.4

Last Answer : (B) 4 0.8

The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient varies with the pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Description : The Sieder-Tate correlation for heat transfer in turbulent flow in pipe gives Nu α Re 0.8 , where, Nu is the Nusselt number and Re is the Reynolds number for the flow. Assuming that this relation is valid, the heat transfer co-efficient ... pipe diameter (D) as (A) D-1.8 (B) D-0.2 (C) D0.2 (D) D1.8

Last Answer : (B) D-0.2

Heat transfer co-efficient equation for forced convection, Nu = 0.023 Re 0.8 . Pr n , is not valid, if the value of (A) n = 0.4 is used for heating (B) n = 0.3 is used for cooling (C) Reynolds number for the flow involved is > 10000 (D) Reynolds number for the flow involved is < 2100

Description : Heat transfer co-efficient equation for forced convection, Nu = 0.023 Re 0.8 . Pr n , is not valid, if the value of (A) n = 0.4 is used for heating (B) n = 0.3 is used for cooling (C) Reynolds number for the flow involved is > 10000 (D) Reynolds number for the flow involved is < 2100

Last Answer : (D) Reynolds number for the flow involved is < 2100

(1/V) (∂V/∂T)Pis the mathematical expression (A) Joule-Thomson co-efficient (B) Specific heat at constant pressure (Cp) (C) co-efficient of thermal expansion (D) Specific heat at constant volume (CV)

Description : (1/V) (∂V/∂T)Pis the mathematical expression (A) Joule-Thomson co-efficient (B) Specific heat at constant pressure (Cp) (C) co-efficient of thermal expansion (D) Specific heat at constant volume (CV)

Last Answer : (C) co-efficient of thermal expansion

(∂T/∂P)H is the mathematical expression for (A) Specific heat at constant pressure (Cp) (B) Specific heat at constant volume (Cv) (C) Joule-Thompson co-efficient (D) None of these

Description : (∂T/∂P)H is the mathematical expression for (A) Specific heat at constant pressure (Cp) (B) Specific heat at constant volume (Cv) (C) Joule-Thompson co-efficient (D) None of these

Last Answer : (C) Joule-Thompson co-efficient

For the same heat load and mass flow rate in the tube side of a shell and tube heat exchanger, one may use multipass on the tube side, because it (A) Decreases the pressure drop (B) Decreases the outlet temperature of cooling medium (C) Increases the overall heat transfer coefficient (D) None of these

Description : For the same heat load and mass flow rate in the tube side of a shell and tube heat exchanger, one may use multipass on the tube side, because it (A) Decreases the pressure drop (B) ... the outlet temperature of cooling medium (C) Increases the overall heat transfer coefficient (D) None of these

Last Answer : (C) Increases the overall heat transfer coefficient

Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Description : Baffles are provided in heat exchangers to increase the (A) Fouling factor (B) Heat transfer area (C) Heat transfer co-efficient (D) Heat transfer rate

Last Answer : (C) Heat transfer co-efficient

Heat transfer rate per unit area is called (A) Thermal conductivity (B) Heat flux (C) Heat transfer co-efficient (D) Thermal diffusivity

Description : Heat transfer rate per unit area is called (A) Thermal conductivity (B) Heat flux (C) Heat transfer co-efficient (D) Thermal diffusivity

Last Answer : (B) Heat flux

Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Description : Which of the following parameters is increased by use of finned tube in a multipass shell and tube heat exchanger? (A) Tube side pressure drop and the heat transfer rate (B) Convective heat transfer co-efficient (C) Effective tube surface area for convective heat transfer (D) All (A) (B) and (C)

Last Answer : (D) All (A) (B) and (C)

. The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C and the heat transfer co-efficient between the outer surface of wall and air is 20 W.m-2 .°C-1 . The rate of heat loss from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175

Last Answer : (A) 165.4

LMTD correction factor which is to be applied for a cross-flow heat exchanger increases with increase in the number of shell passes. Its value for a single pass cross flow heat exchanger is (A) 0 (B) 1 (C) > 1 (D) < 1

Description : LMTD correction factor which is to be applied for a cross-flow heat exchanger increases with increase in the number of shell passes. Its value for a single pass cross flow heat exchanger is (A) 0 (B) 1 (C) > 1 (D) < 1

Last Answer : (D) < 1

In a parallel flow heat exchanger, if the outlet temperature of hot and cold fluids are the same, then the log mean temperature difference (LMTD) is (A) Minimum (B) Maximum (C) Zero (D) Infinity

Description : In a parallel flow heat exchanger, if the outlet temperature of hot and cold fluids are the same, then the log mean temperature difference (LMTD) is (A) Minimum (B) Maximum (C) Zero (D) Infinity

Last Answer : (C) Zero