Pore size of the molecular sieve 5A is __________ mm.
(A) 5
(B) 0.5
(C) 0.05
(D) 50
Description : If aggregates completely pass through a sieve of size 75 mm and are retained on a sieve of size 60 mm, the particular aggregate will be flaky if its minimum dimension is less than (A) 20.5 mm (B) 30.5 mm (C) 40.5 mm (D) 50.5 mm
Last Answer : Answer: Option C
Description : The most suitable pore size for bacterial filtration in a membrane filter is ------- A 0.22 mm B 0.45 nm C 0.22 µm D 30 µm
Last Answer : C 0.22 µm
Description : Regeneration of molecular sieve requires it to be heated to a temperature of about __________ °C. (A) 80-120 (B) 200-300 (C) 600-800 (D) 1000-1100
Last Answer : (D) 1000-1100
Description : The Knudsen diffusivity is dependent on the (A) Molecular velocity only (B) Pore radius of the catalyst only (C) Molecular mean free path only (D) Molecular velocity and pore radius of the catalyst
Last Answer : (D) Molecular velocity and pore radius of the catalyst
Description : A soil sample has passing 0.075 mm sieve = 60% liquid limit = 65% and plastic limit = 40%. The group index of the soil, is (A) 5 (B) 20 (C) 40 (D) None of these
Last Answer : (D) None of these
Description : Vibrating screens have capacity in the range of __________ tons/ft 2 .mm mesh size. (A) 0.2 to 0.8 (B) 5 to 25 (C) 50 to 100 (D) 100 to 250
Last Answer : (A) 0.2 to 0.8
Description : or Indian standard (IS) screens, the mesh number is equal to its aperture size expressed to the nearest deca-micron (0.01 mm). Aperture width of IS screen of mesh number 50 will be approximately __________ microns. (A) 5 (B) 50 (C) 500 (D) 5000
Last Answer : (C) 500
Description : 200 mesh sieve size corresponds to __________ microns. (A) 24 (B) 74 (C) 154 (D) 200
Last Answer : (B) 74
Description : For an ordinary Portland cement (A) Residual does not exceed 10% when sieved through IS Sieve No. 9 (B) Soundness varies from 5 to 10 mm (C) Initial setting time is not less than 30 minutes (D) Compressive stress after 7 days, is not less than 175 kg/cm2
Last Answer : (C) Initial setting time is not less than 30 minutes
Description : An aggregate which passes through 25 mm I.S. sieve and is retained on 20 mm sieve, is said to be flaky if its least dimension is less than (A) 22.5 mm (B) 18.5 mm (C) 16.5 mm (D) 13.5 mm
Last Answer : Answer: Option D
Description : I.S. Sieve Nos. 10 mm and 4.75 mm are generally used for grading of (A) Coarse aggregates (B) Fine aggregates (C) Neither (a) nor (b) (D) Both (a) and (b)
Description : If a grading curve is horizontal between the portions of 20 mm I.S. Sieve and 4.75 mm I.S. Sieve, the graded aggregates do not contain (A) 20 mm particles (B) 10 mm particles (C) 4.75 mm particles (D) All the above
Description : If Thiele modulus is __________, then the pore diffusion resistance in a catalyst may be considered as negligible. (A) 0 (B) ∞ (C) < 0.5 (D) > 0.5
Last Answer : (C) < 0.5
Description : In a size reduction crushing operation, the feed size is 10 to 50 mm, while the product size is 2 to 10 mm. This is a case of __________ crushing. (A) Primary (B) Secondary (C) Fine
Last Answer : (C) Fine
Description : In a size reduction crushing operation, feed size is 100 to 300 mm. while the product size is 10 to 50 mm. This is a case of the __________ crushing. (A) Primary (B) Secondary (C) Fine (D) Ultrafine
Last Answer : (B) Secondary
Description : A simply supported beam deflects by 5 mm when it is subjected to a concentrated load of 10 kN at its centre. What will be deflection in a 1/10 model of the beam if the model is subjected to a 1 kN load at its centre? (A) 5 mm (B) 0.5 mm (C) 0.05 mm (D) 0.005 mm
Last Answer : (A) 5 mm
Description : Hazen’s formula VS = 418 (GS – Gw)d [(3T + 70)/100] is used for the settlement velocity of the particles of diameter A. Less than 0.01 mm B. Less than 0.05 mm C. Less than 0.1 mm D. Greater than 0.1 mm
Last Answer : ANS: D
Description : The diameter of very fine sand particles is- (a) Below 0.002 mm (b) 0.05-0.002mm (c) 0.01-0.05 mm (d) 0.05-0.10mm
Last Answer : (c) 0.01-0.05 mm
Description : The force per unit length of two conductors carrying equal currents of 5A separated by a distance of 20cm in air(in 10 -6 order) a) 25 b) 35 c) 40 d) 50
Last Answer : a) 25
Description : Find the power of an inductor of 5H and current 4.5A after 2 seconds. a) 25.31 b) 50.62 c) 102.4 d) 204.8
Last Answer : a) 25.31
Description : A cylinder contains oxygen at a pressure of 10 atm and a temperature of 300 K. The volume of the cylinder is 10 liters. What is the mass of the oxygen in grams? Molecular weight (MW) of oxygen is 32 g/mole? a. 125.02 b. 130.08 c. 135.05 d. 120.04
Last Answer : 130.08 {(10atm)(10)(32)/(0.0821) (300K)}
Description : The importance of diffusion in a catalyst are increased by (A) Large catalyst particle size (B) An active surface of the catalyst (C) Small pore diameter (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : If the catalyst pore size is small in comparison with the mean free path, collisions with the pore wall controls the process'. The diffusivity under this condition is called 'Knudsen diffusivity', which is affected by the (A) Pressure (B) Temperature (C) Both (A) & (B) (D) Neither (A) nor (B)
Last Answer : (B) Temperature
Description : Pick out the wrong statement. (A) Exit age description function (E) and internal age distribution function (I) are related as, E = -(dI/dθ) (B) Chemisorption studies are useful in the ... energy (D) A catalyst increases the potential energy barrier over which the reactants must pass to form products
Last Answer : (D) A catalyst increases the potential energy barrier over which the reactants must pass to form products
Description : BET apparatus is used to determine the (A) Specific surface of a porous catalyst (B) Pore size distribution (C) Pore diameter (D) Porosity of the catalyst bed
Last Answer : (A) Specific surface of a porous catalyst
Description : Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3 /min) of density 800 kg/m3 and specific heat of ... mean temperature difference in °C is approximately (A) 32 (B) 37 (C) 45 (D) 50
Last Answer : (A) 32
Description : Pick out the correct statement pertaining to transition/ entrance length in fluid flow. (A) The length of entrance region of pipe, in which full development of fluid flow takes place such that velocity profile does not change ... pipe of diameter 'd' is equal to 50 D (D) All (A), (B) and (C)
Description : Helium-mercury method can be used to determine the __________ of the catalyst particle. (A) Pore volume (B) Solid density (C) Porosity (D) All (A), (B), & (C)
Last Answer : (D) All (A), (B), & (C)
Description : Helium-mercury method is used for the measurement of the __________ of the catalyst. (A) Surface area (B) Porosity (C) Pore volume (D) Both (B) & (C)
Last Answer : (D) Both (B) & (C)
Description : Effectiveness factor of a catalyst pellet is a measure of the __________ resistance. (A) Pore diffusion (B) Gas film (C) Chemical reaction (D) None of these
Last Answer : (A) Pore diffusion
Description : Bulk diffusion in catalyst pore __________ with increase in pressure. (A) Increases (B) Decreases (C) Remains unchanged (D) Increases exponentially
Last Answer : (B) Decreases
Description : . B.E.T. method can be used to determine the __________ of a porous catalyst. (A) Solid density (B) Pore volume (C) Surface area (D) All (A), (B) and (C)
Last Answer : (C) Surface area
Description : If a solid-gas non-catalytic reaction occurs at very high temperature, the rate controlling step is the __________ diffusion. (A) Film (B) Ash layer (C) Pore (D) None of these
Last Answer : (A) Film
Description : Pulverised coal passing through 200 mesh screen has a diameter of 0.074 mm (74 micron). The same passing through 50 mesh screen will have a dia of __________ mm. (A) 0.007 (B) 0.30 (C) 50 (D) 0.014
Last Answer : (B) 0.30
Description : A helical spring is fabricated by wrapping wire 19.05 mm in diameter around a forming cylinder 203.2 mm in diameter. Compute the number of turns required to permit an elongation of 101.6 mm. without exceeding a shearing ... G = 82737 N/mm2. a. 10 turns b. 20 turns c. 25 turns d. 30 turns
Last Answer : a. 10 turns
Description : Work index is the gross energy (kWh/tonne of feed) necessary to reduce a very large feed to such a size that 80% of product particles will pass through a 0.1 mm screen. The value of work index determined for wet grinding should ... to get the same for dry grinding. (A) 1.0 (B) 0.5 (C) 1.34 (D) 4.34
Last Answer : (C) 1.34
Description : Hydrogenation of oil is carried out in a/an __________ in Vanaspati manufacturing plant. (A) Agitated vessel (B) Sieve tray column (C) Bubble cap column (D) Packed tower
Last Answer : (A) Agitated vessel
Description : __________ columns are used for liquid dispersion in a continuous gas phase. (A) Packed (B) Pulse (C) Bubble cap (D) Sieve plate
Last Answer : (A) Packed
Description : __________ column is used in gas absorption process. (A) Wetted wall (B) Sieve/perforated tray (C) Bubble cap (D) Packed
Last Answer : (D) Packed
Description : __________ extractor is used for the concentration of radioactive nuclear waste. (A) Pulsed column (B) Sieve plate (C) Mixer-settler (D) Bollman
Last Answer : (A) Pulsed column
Description : There are five concentric layers within the atmosphere which is differentiated on the basis of temperature. The atmospheric layer which lies close to the earth's surface in which human being along with other organisms live is called ... is about __________ °C/km. (A) 0.05 (B) 1 (C) 6.5 (D) 15
Last Answer : (C) 6.5
Description : Salt content in sea water is about __________ percent. (A) 0.5 (B) 1 (C) 3.5 (D) 9.05
Last Answer : (C) 3.5
Description : Cation exchange resins (0.3 to 1 mm size) used in water treatment is prepared from __________ resins. (A) Epoxy (B) Phenol formaldehyde (C) Urea formaldehyde (D) Melamine formaldehyde
Last Answer : (C) Urea formaldehyde
Description : Size of blast furnace grade coke is __________ mm. (A) 25-80 (B) 0-15 (C) 15-25 (D) > 100
Last Answer : (A) 25-80
Description : Flat rate parcel rates Flat Rate Parcel Boxes size Dimension of boxes (in mm) Weight (in Kg.) Tariff (in Rs.) Small - S 250*50*300 0 to 1 125 Medium - M 250*100*300 Above 1 to 2.5 200 Large - L 300*250*200 Above 2.5 to 5 400
Last Answer : Large - L 300*250*200 Above 2.5 to 5 400
Description : If the viscosity of ground water is 1.00, the Slitcher's constant is 400, the effective size of soil particles in aquifer is 0.5 mm and hydraulic gradient is 1 in 80, the velocity of flow is (A) 0.25 m/day (B) 0.50 m/day (C) 1.00 m/day (D) 1.25 m/day
Description : Density of high density polythene is about __________ gm/c.c. (A) 1.18 (B) 1.05 (C) 0.95 (D) 0.99
Last Answer : (C) 0.95
Description : . In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal
Last Answer : (D) Rotor shaft carrying hammers can be vertical or horizontal
Description : Pick up the incorrect statement from the following: (A) The smaller the size of the pores, the higher the water can rise above the water table (B) Below the water table, the pore water may be static (C) The hydrostatic pressure depends on the depth below the water level (D) None of these
Description : What is the Thiele modulus of the solid catalysed first order reaction as shown in the bellow figure, if the pore diffusion offers negligible resistance to reaction? (A) < 5 (B) < 0.5 (C) > 1 (D) 5
Last Answer : (B) < 0.5