Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Weld decay will cause which of the following problems?
a) A reduced resistance to corrosion b) a lower tensile strength
c) The toughness is reduced d) The hardness will increase
by

1 Answer

Answer :

a) A reduced resistance to corrosion
by

Related questions

Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance

Description : Shock resisting steels should possess high (A) Hardness (B) Toughness (C) Tensile strength (D) Wear resistance

Last Answer : (B) Toughness

The area under stress-strain curve represents a.Hardness of material b.Breaking strength of the material c.Energy required to cause failure d.Toughness of material e.Malleabbility of material

Description : The area under stress-strain curve represents a.Hardness of material b.Breaking strength of the material c.Energy required to cause failure d.Toughness of material e.Malleabbility of material

Last Answer : c. Energy required to cause failure

_______ property of a material is determined by the Herbert Pendulum device. (A) Hardness (B) Tensile (C) Toughness (D) Compressive

Description : _______ property of a material is determined by the Herbert Pendulum device. (A) Hardness (B) Tensile (C) Toughness (D) Compressive

Last Answer : (A) Hardness

Weld decay can be minimized by specifying steel with: a) Higher carbon level b) higher chromium level c) lower carbon level d) lower chromium level

Description : Weld decay can be minimized by specifying steel with: a) Higher carbon level b) higher chromium level c) lower carbon level d) lower chromium level

Last Answer : c) lower carbon level

Wrought iron is having very high (A) Hardness (B) Strength (C) Corrosion resistance (D) Susceptibility to changes in its properties by heat treatment

Description : Wrought iron is having very high (A) Hardness (B) Strength (C) Corrosion resistance (D) Susceptibility to changes in its properties by heat treatment

Last Answer : (C) Corrosion resistance

Smith's test of stones is performed to find out (A) The presence of soluble matter of stone (B) The compressive strength of the stone (C) The hardness of the stone (D) The toughness of the stone

Description : Smith's test of stones is performed to find out (A) The presence of soluble matter of stone (B) The compressive strength of the stone (C) The hardness of the stone (D) The toughness of the stone

Last Answer : Answer: Option A

Detrimental property of a material for shock load applications (a) High density (b) Low toughness (c) High strength (d) Low hardness

Description : Detrimental property of a material for shock load applications (a) High density (b) Low toughness (c) High strength (d) Low hardness  

Last Answer : (b) Low toughness

Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Description : Addition of lead, sulphur and phosphorus to low carbon steel helps in improving its (A) Corrosion resistance (B) Tensile strength (C) Machinability (D) Compressive strength

Last Answer : (C) Machinability

Presence of cobalt in steel improves its (A) Cutting ability (B) Corrosion resistance (C) Tensile strength

Description : Presence of cobalt in steel improves its (A) Cutting ability (B) Corrosion resistance (C) Tensile strength

Last Answer : (A) Cutting ability

High copper amalgam lasts longer than low copper amalgam because of:** A. Increased compressive strength B. Increased corrosion resistance C. High creep D. Increased tensile strength E. Decreased setting expansion

Description : High copper amalgam lasts longer than low copper amalgam because of:**  A. Increased compressive strength  B. Increased corrosion resistance  C. High creep  D. Increased tensile strength  E. Decreased setting expansion 

Last Answer : A. Increased compressive strength 

Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Description : Which of the following mechanical properties of a material is most structure insensitive? (A) Modulus of elasticity (young's modulus) (B) Toughness (C) Percentage reduction of area (D) Tensile strength

Last Answer : (A) Modulus of elasticity (young's modulus)

On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Description : On decreasing the grain size of a polycrystalline material, the property most likely to deteriorate is (A) Creep (B) Toughness (C) Tensile strength (D) Fatigue

Last Answer : (B) Toughnes

The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Description : The percentage elongation and the percentage reduction in area depends upon (a) Tensile strength of the material (b) Ductility of the material (c) Toughness of the material (d) None of these

Last Answer : B

With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)

Description : With increase in the carbon percentage in the steel, its (A) Hardness increases (B) Ductility reduces (C) Tensile strength increases (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The ability of a material to offer resistance to scratching or indentation is a measure of its (A) Brittleness (B) Toughness (C) Hardness (D) Resilience

Description : The ability of a material to offer resistance to scratching or indentation is a measure of its (A) Brittleness (B) Toughness (C) Hardness (D) Resilience

Last Answer : (C) Hardness

Presence of manganese in alloy steel improves its (A) Corrosion resistance (B) Cutting ability (C) Abrasion resistance & toughness (D) Elasticity & creep resistance

Description : Presence of manganese in alloy steel improves its (A) Corrosion resistance (B) Cutting ability (C) Abrasion resistance & toughness (D) Elasticity & creep resistance

Last Answer : (C) Abrasion resistance & toughness

Non-ferrous alloys used for making cutting tools need not have high (A) Abrasion resistance (B) Toughness (C) Red hardness (D) Cutting speed

Description : Non-ferrous alloys used for making cutting tools need not have high (A) Abrasion resistance (B) Toughness (C) Red hardness (D) Cutting speed

Last Answer : (C) Red hardness

A post weld heat treatment may also be of benefit in minimizing the risk of weld decay, this heat treatment would be called? a) Stress relief b) Normalizing c) Quench and Tempering d) Solution treatment over 1000 °C

Description : A post weld heat treatment may also be of benefit in minimizing the risk of weld decay, this heat treatment would be called? a) Stress relief b) Normalizing c) Quench and Tempering d) Solution treatment over 1000 °C

Last Answer : d) Solution treatment over 1000 °C

Weld decay is caused by the formation of a compound with carbon. The other element in this compound is: a) Manganese b) Sulphur c) Chromium d) Nickel

Description : Weld decay is caused by the formation of a compound with carbon. The other element in this compound is: a) Manganese b) Sulphur c) Chromium d) Nickel

Last Answer : c) Chromium

Weld decay occurs in which of the following steel types? a) Carbon/Manganese b) Low alloy c) Any stainless steel d) Austenitic stainless steels

Description : Weld decay occurs in which of the following steel types? a) Carbon/Manganese b) Low alloy c) Any stainless steel d) Austenitic stainless steels

Last Answer : d) Austenitic stainless steels

In a transverse WELD tensile test, if the break was in the weld metal, the sample would he: a) Rejected b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate c) Retested d) Acceptable if the UTS is between 80 - 90% of the specified UTS of the plate

Description : In a transverse WELD tensile test, if the break was in the weld metal, the sample would he: a) Rejected b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate c) Retested d) Acceptable if the UTS is between 80 - 90% of the specified UTS of the plate

Last Answer : b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate

Steels with high carbon equivalent have poor Weldability, because in these steels during welding (A) Carbon and other alloying elements get oxidised from the weld pool (B) Excessive ferrite forms in the heat affected zone leading to poor toughness of the weld (C) Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld (D) Segregation of carbon and other element occurs in the weld pool leading to poor properties of the weld

Description : Steels with high carbon equivalent have poor Weldability, because in these steels during welding (A) Carbon and other alloying elements get oxidised from the weld pool (B) Excessive ferrite forms in the ... of carbon and other element occurs in the weld pool leading to poor properties of the weld

Last Answer : (C) Martensite forms in the heat affected zone leading to poor toughness/ductility of the weld

A metallic alloy in general as compared to their pure metal components is (A) More corrosion resistant (B) Having higher melting point (C) Having lower hardness, reactivity and fusibility (D) Having lower electrical conductivity

Description : A metallic alloy in general as compared to their pure metal components is (A) More corrosion resistant (B) Having higher melting point (C) Having lower hardness, reactivity and fusibility (D) Having lower electrical conductivity

Last Answer : (A) More corrosion resistant

. In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

Description : . In a linear polymer, the monomeric units are linked together to form long straight chains. The cross linked or branched chain polymers compared to linear polymers have higher (A) Densities (B) Melting point (C) Tensile strength (D) Hardness, rigidity & brittleness

Last Answer : (D) Hardness, rigidity & brittleness

Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process

Description : Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process

Last Answer : (B) Tensile strength

Manganese in steel affects its (A) Ductility (B) Tensile strength (C) Hardness (D) None of these

Description : Manganese in steel affects its (A) Ductility (B) Tensile strength (C) Hardness (D) None of these

Last Answer : (B) Tensile strength

With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Last Answer : (A) Impact strength

In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Description : In case of brasses, with decreasing zinc percentage and increasing copper percentage, its __________ increases. (A) Percentage elongation (B) Brinell hardness (C) Tensile strength (D) All 'a', 'b' & 'c'

Last Answer : (A) Percentage elongation

Primary designation of steel is based on its (A) Hardness & tensile strength (B) Carbon content (C) Iron content (D) Alloying elements content

Description : Primary designation of steel is based on its (A) Hardness & tensile strength (B) Carbon content (C) Iron content (D) Alloying elements content

Last Answer : (D) Alloying elements content Sh

Wrought iron is not (A) Ductile & resistant to corrosion/rusting (B) Weldable easily (C) Having uniform strength in all directions (D) Having maximum tensile strength along the lines of slag distribution

Description : Wrought iron is not (A) Ductile & resistant to corrosion/rusting (B) Weldable easily (C) Having uniform strength in all directions (D) Having maximum tensile strength along the lines of slag distribution

Last Answer : Option C

.The main advantage of amalgam with high content of Cu is: A. Better marginal sealing B. Less corrosion C. Better tensile strength D. Higher and immediate compressive strength

Description : .The main advantage of amalgam with high content of Cu is: A. Better marginal sealing B. Less corrosion C. Better tensile strength D. Higher and immediate compressive strength

Last Answer : B. Less corrosion

Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Description : Distortion or change in shape of a cast partial denture clasp during its clinical use probably indicates that the: A. Ductility was too low B. Hardness was too great C. Ultimate tensile strength was too low D. Tension temperature was too high E. Elastic limit was exceeded

Last Answer : E. Elastic limit was exceeded

Tick of the property, which is different from the group (A) Ductility. (B) Resistivity. (C) Tensile strength. (D) Hardness.

Description : Tick of the property, which is different from the group (A) Ductility. (B) Resistivity. (C) Tensile strength. (D) Hardness.

Last Answer : (B) Resistivity

Define the term: i)Tensile strength ii) Hardness iii) Ductility iv) Soldering

Description : Define the term: i)Tensile strength ii) Hardness iii) Ductility iv) Soldering

Last Answer : i)Tensile Strength : Tensile Strength is the ability of metal to carry a load without breaking. ii)Hardness :- Hardness is the ability of metal to resist wear or abrasion and resist penetration. ... a non ferrous alloy having melting point below 4000 c in between them is called as soldering. 

Addition of tungsten to steel imparts (A) Magnetic properties (B) Cutting hardness (C) Corrosion resistance (D) Ductility

Description : Addition of tungsten to steel imparts (A) Magnetic properties (B) Cutting hardness (C) Corrosion resistance (D) Ductility

Last Answer : (B) Cutting hardness

Which of the following in NOT a quantitative test? a) Root bend b) Macro hardness c) Charpy d) Tensile

Description : Which of the following in NOT a quantitative test? a) Root bend b) Macro hardness c) Charpy d) Tensile

Last Answer : a) Root bend

Pick up the correct statement from the following: (A) Catalysts are added to assist and accelerate the hardening of resin (B) The fillers are inert materials and they impart strength and hardness (C) Fibrous fillers increase thermal resistance (D) All the above

Description : Pick up the correct statement from the following: (A) Catalysts are added to assist and accelerate the hardening of resin (B) The fillers are inert materials and they impart strength and hardness (C) Fibrous fillers increase thermal resistance (D) All the above

Last Answer : Answer: Option D

Grindability of a material does not depend upon its (A) Elasticity (B) Hardness (C) Toughness (D) Size

Description : Grindability of a material does not depend upon its (A) Elasticity (B) Hardness (C) Toughness (D) Size

Last Answer : (D) Size

The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Description : The ability of materials to develop a characteristic behavior under repeated loading known as ___________ a) Toughness b) Resilience c) Hardness d) Fatigue

Last Answer : d) Fatigue

Pick out the correct statement. (A) Hot worked materials are subjected to annealing to remove internal stresses (B) Annealing of steel hardens it slightly (C) Normalising of a material induces stresses (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness

Description : Pick out the correct statement. (A) Hot worked materials are subjected to annealing to remove internal stresses (B) Annealing of steel hardens it slightly (C) Normalising of a material induces stresses (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness

Last Answer : (D) Tempering of a material improves ductility & toughness but reduces hardness & brittleness Share

The important test to be conducted on a stone used in docks and harbours is (A) Hardness test (B) Workability test (C) Weight test (D) Toughness test

Description : The important test to be conducted on a stone used in docks and harbours is (A) Hardness test (B) Workability test (C) Weight test (D) Toughness test

Last Answer : Answer: Option C

Define the terms: i) Hardness ii) Toughness iii) Brazing iv) Machinability

Description : Define the terms: i) Hardness ii) Toughness iii) Brazing iv) Machinability

Last Answer : i) Hardness:- Hardness is the property of metal possessed by a material which enables it to resist penetration or abrasion or scratching by other material. Diamond is the hardest of known materials.  ... can be easily cut by cutting tools to produce a desired shape & surface finish on its surface

Moist atmospheric air at high temperature (e.g., in summer) having high concentration of sulphur dioxide causes(A) Fading of dyes on textiles(B) Corrosion, tarnishing & soiling of metals(C) Reduced strength of textiles(D) All (A), (B) and (C)

Description : Moist atmospheric air at high temperature (e.g., in summer) having high concentration of sulphur dioxide causes (A) Fading of dyes on textiles (B) Corrosion, tarnishing & soiling of metals (C) Reduced strength of textiles (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Half life is a term used to describe a) The penetrating ability a gamma source b) Half the total time a gamma source will be useful c) The time taken for the gamma source to reduce the strength by half d) The rate of decay of an X-ray tube

Description : Half life is a term used to describe a) The penetrating ability a gamma source b) Half the total time a gamma source will be useful c) The time taken for the gamma source to reduce the strength by half d) The rate of decay of an X-ray tube

Last Answer : c) The time taken for the gamma source to reduce the strength by half

In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Description : In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Last Answer : c) % A is 30

When MMA welding what will be the effect on the weld f the power source was changed from AC to DC-ve? a) None b) Higher deposition rate c) It would slightly increase the depth of penetration d) The arc would become unstable

Description : When MMA welding what will be the effect on the weld f the power source was changed from AC to DC-ve? a) None b) Higher deposition rate c) It would slightly increase the depth of penetration d) The arc would become unstable

Last Answer : b) Higher deposition rate

Ceramic nuclear metals compared to solid nuclear metals have (A) Higher melting points (B) Low strength at high temperature (C) More chances of radiation damage (D) Poorer corrosion resistance

Description : Ceramic nuclear metals compared to solid nuclear metals have (A) Higher melting points (B) Low strength at high temperature (C) More chances of radiation damage (D) Poorer corrosion resistance

Last Answer : (A) Higher melting points

The addition of antimony in tin-based alloys improves its (A) Rupture strength and hot hardness (B) Impact strength and bonding strength (C) Deformation resistance (D) Wear resistance

Description : The addition of antimony in tin-based alloys improves its (A) Rupture strength and hot hardness (B) Impact strength and bonding strength (C) Deformation resistance (D) Wear resistance

Last Answer : (C) Deformation resistance

Aluminium alloy is one of the most suitable materials of construction for aircrafts mainly due to its (A) High strength to weight ratio (B) Low temperature strength properties (C) Its ability to be cast, rolled, forged & stamped (D) High strength and corrosion & oxidation-resistance at elevated temperature

Description : Aluminium alloy is one of the most suitable materials of construction for aircrafts mainly due to its (A) High strength to weight ratio (B) Low temperature strength properties (C) Its ability ... rolled, forged & stamped (D) High strength and corrosion & oxidation-resistance at elevated temperature

Last Answer : (A) High strength to weight ratio

Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Description : Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Last Answer : (A) Impact strength