In a transverse WELD tensile test, if the break was in the weld metal, the sample would he: a) Rejected b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate c) Retested d) Acceptable if the UTS is between 80 - 90% of the specified UTS of the plate

In a transverse WELD tensile test, if the break was in the weld metal, the sample would he:  
a) Rejected  
b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate
c) Retested  
d) Acceptable if the UTS is between 80 - 90% of the specified UTS of the plate
by

1 Answer

Answer :

b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate
by

Related questions

In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Description : In a cross joint tensile test the following observations were made: Specimen width 20mm, Material thickness 20mm, Max Load: 180kN, Break position: Parent Plate. What is the UTS? a) 45 kN/mm b) 450 N/mm2c) 39 kN/mm2d) 39 N/mm2

Last Answer : b) 450 N/mm2

In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Description : In a welding procedure transverse joint tensile test the following observations were made. The specimen CSA was recorded as 30mm x 20mm and the maximum load applied was recorded as 200kN. What is the UTS? a) 33kN/mm2b) 333N/mm2c) 3333N/mm2d) 33N/mm2

Last Answer : b) 333N/mm2

When examining a completed bend test, the angle of the bend was found to be 185°. The testing specification calls for the sample to have been formed through 180°? a) They should be acceptable as the standard refers to minimum forming angle b) The bends should be considered as fail c) New bends should be produced and bent to 180° then re-examined d) They should be rejected as the angle is not close enough to be acceptable

Description : When examining a completed bend test, the angle of the bend was found to be 185°. The testing specification calls for the sample to have been formed through 180°? a) They should be acceptable as ... then re-examined d) They should be rejected as the angle is not close enough to be acceptable

Last Answer : c) New bends should be produced and bent to 180° then re-examined

Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False

Description : Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False

Last Answer : b) False

Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Description : Weld decay will cause which of the following problems? a) A reduced resistance to corrosion b) a lower tensile strength c) The toughness is reduced d) The hardness will increase

Last Answer : a) A reduced resistance to corrosion

Tandem rig test with 450 probe for AT weld detects. (i) Horizontal longitudinal defect in weld. (ii) Vertical oriented defect in AT weld.* (iii) Transverse defect in AT weld. (iv) Defect in flange of AT welds.

Description : Tandem rig test with 450 probe for AT weld detects. (i) Horizontal longitudinal defect in weld. (ii) Vertical oriented defect in AT weld.* (iii) Transverse defect in AT weld. (iv) Defect in flange of AT welds.

Last Answer : (ii) Vertical oriented defect in AT weld.*

Min. breaking load of 60kg weld during transverse breaking load test is? (i) 110 MT (ii) 115 MT* (iii) 90 MT (iv) 120 MT

Description : Min. breaking load of 60kg weld during transverse breaking load test is? (i) 110 MT (ii) 115 MT* (iii) 90 MT (iv) 120 MT

Last Answer : (ii) 115 MT*

Min. breaking load of 52kg weld during transverse breaking load test is? (i) 90MT* (ii) 100 MT (iii) 110 MT (iv) 120 MT

Description : Min. breaking load of 52kg weld during transverse breaking load test is? (i) 90MT* (ii) 100 MT (iii) 110 MT (iv) 120 MT

Last Answer : (i) 90MT*

In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Description : In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Last Answer : (c) 2 × Throat of weld

When the steel is subjected to normalising, its __________ decreases. (A) Yield point (B) Ductility (C) Ultimate tensile strength (UTS)

Description : When the steel is subjected to normalising, its __________ decreases. (A) Yield point (B) Ductility (C) Ultimate tensile strength (UTS)

Last Answer : (B) Ductility

Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron Answer: Option C

Description : Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron Answer: Option C

Last Answer : (C) Cast iron

With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Description : With increasing carbon percent in steel beyond 0.8%, its ultimate tensile strength (UTS) and __________ is not affected. (A) Impact strength (B) Percent elongation (C) Hardness (D) Both 'b' & 'c'

Last Answer : (A) Impact strength

Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron

Description : Which of the following has the least value of ultimate tensile strength (UTS)? (A) Medium carbon steel (B) High carbon steel (C) Cast iron (D) Wrought iron

Last Answer : Option B

What is the full form UTS of rails a. Ultimate technical Strength b. Ultimate tensile Strength* c. Upper Top surface d. None of above

Description : What is the full form UTS of rails a. Ultimate technical Strength b. Ultimate tensile Strength* c. Upper Top surface d. None of above

Last Answer : b. Ultimate tensile Strength*

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Description : In an all weld tensile test, the original specimen gauge length was 50mm, and after the test the increased gauge length was 65mm, what is the elongation percentage? a) % A is 40 b) % A is 60 c) % A is 30 d) % A is 36

Last Answer : c) % A is 30

When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress

Description : When equal and opposite forces applied to a body, tend to elongate it, the stress so produced, is called (A) Shear stress (B) Compressive stress (C) Tensile stress (D) Transverse stress

Last Answer : (C) Tensile stress

For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Description : For two plates of equal thickness, full strength of square-edged fillet weld can be ensured if its maximum size is limited to (a) 1.5 mm less than the plate thickness (b) 67% of the plate thickness (c) 80% of the plate thickness (d) Thickness of the plate

Last Answer : (a) 1.5 mm less than the plate thickness

he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Description : he transverse fillet welded joints are designed for (a) tensile strength (b) compressive strength (c) bending strength (d) shear strength

Last Answer : (a) tensile strength

Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Last Answer : b) False

A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Last Answer : b) False

Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None

Description : Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None

Last Answer : (i)0.707 tl

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Last Answer : b) False

If force act in a direction parallel to the direction of weld, then fillet weld is called as? a) Transverse b) Longitudinal c) Parallel d) Longitudinal or Parallel

Description : If force act in a direction parallel to the direction of weld, then fillet weld is called as? a) Transverse b) Longitudinal c) Parallel d) Longitudinal or Parallel

Last Answer : d) Longitudinal or Parallel

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl

A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Description : A force 2P is acting on the double transverse fillet weld. Leg of weld is h and length l. Determine the shear stress in a plane inclined at θ with horizontal. a) PSinθ(Sinθ+Cosθ)/hl b) P(Sinθ+Cosθ)/hl c) Pcosθ(Sinθ+Cosθ)/hl d) None of the listed

Last Answer : a) PSinθ(Sinθ+Cosθ)/hl

Why is it essential to clean the excess weld metal on completion of the production weld? a) So it can be ready for painting b) To remove any rust c) To ensure it is suitably clean for visual inspection and NDT d) To remove slag from the undercut

Description : Why is it essential to clean the excess weld metal on completion of the production weld? a) So it can be ready for painting b) To remove any rust c) To ensure it is suitably clean for visual inspection and NDT d) To remove slag from the undercut

Last Answer : c) To ensure it is suitably clean for visual inspection and NDT

Why would visual inspection of the excess weld metal at the bottom of a cross country pipeline be important? a) It is the most difficult area to weld b) It is the dirtiest part of the pipe as it is near the ground c) Welders always forget to weld the bottom d) It is the most difficult area to radiograph

Description : Why would visual inspection of the excess weld metal at the bottom of a cross country pipeline be important? a) It is the most difficult area to weld b) It is the dirtiest part of the pipe as ... ground c) Welders always forget to weld the bottom d) It is the most difficult area to radiograph

Last Answer : a) It is the most difficult area to weld

Give a logical expression for : 1) score is greater than or equal to 80 but less than 90 -Technology

Description : Give a logical expression for : 1) score is greater than or equal to 80 but less than 90 -Technology

Last Answer : \(80

As per IS:456, the strength of concrete sample is less than [ A ] The characteristic strength minus 1.35times the standard deviation [ B ] 0.80 times the characteristic strength [ C ] Greater of (a) and (b) [ D ] None of the above

Description : As per IS:456, the strength of concrete sample is less than [ A ] The characteristic strength minus 1.35times the standard deviation [ B ] 0.80 times the characteristic strength [ C ] Greater of (a) and (b) [ D ] None of the above

Last Answer : [ C ] Greater of (a) and (b)

The natural water content of the soil sample was found to be 40%, specific gravity is 2.7 and void ratio 1.2; then the degree of saturation of the soil will be (a) 100% (b) 69% (c) 87% (d) 90%

Description : The natural water content of the soil sample was found to be 40%, specific gravity is 2.7 and void ratio 1.2; then the degree of saturation of the soil will be (a) 100% (b) 69% (c) 87% (d) 90%

Last Answer : (d) 90%

Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Description : Transverse fillet welds are under (i) Bending and shear stresses (ii)Compressive and torsion shear stresses (iii)Tensile and compressive stresses (iv)None

Last Answer : (iv)None

Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Description : Transverse fillet welds are under (i) Shear stress (ii) Compressive stress (iii) Tensile stress

Last Answer : (iii) Tensile stress

When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be A Shear stress B Bending stress C Tensile stress D Compressive stress

Last Answer : B Bending stress

During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above

Description : During transverse vibrations, shaft is subjected to which type of stresses? A) Tensile stresses B) Torsional shear stress C) Bending stresses D) All of the above

Last Answer : C) Bending stresses

When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body B will be (A) Shear stress (B) Bending stress (C) Tensile stress (D)Compressive stress

Last Answer : (B) Bending stress

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Last Answer : b) bending stress

During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above

Description : During transverse vibrations, shaft is subjected to which type of stresses? a. Tensile stresses b. Torsional shear stress c. Bending stresses d. All of the above

Last Answer : c. Bending stresses

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) bending stress c) tensile stress d) compressive stress

Last Answer : b) bending stress

When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) tensile stress c) compressive stress d) none of the mentioned

Description : When a body is subjected to transverse vibrations, the stress induced in a body will be a) shear stress b) tensile stress c) compressive stress d) none of the mentioned

Last Answer : b) tensile stress

t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved qualification to cover the intended scope of work d) Yes as long as no NDT is required on the finished weld

Description : t is permissible to allow trainee welder to carry out production welding? a) Never b) Yes as long as the supervisor is happy with his workmanship standard c) Yes as long as he has the approved ... cover the intended scope of work d) Yes as long as no NDT is required on the finished weld

Last Answer : a) Never

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process

Description : Cast irons are generally specified by their (A) Carbon content (B) Tensile strength (C) Hardness (D) Manufacturing process

Last Answer : (B) Tensile strength

(2) amount of oxygen used for biochemical oxidation Explanation: Biochemical oxygen demand or B.O.D. is the amount of dissolved oxygen needed by aerobic biological organisms in a body of water to break down organic material present in a given water sample at certain temperature over a specific time period. The term also refers to a chemical procedure for determining this amount. This is not a precise quantitative test, although it is widely used as an indication of the organic quality of water.

Description : (2) amount of oxygen used for biochemical oxidation Explanation: Biochemical oxygen demand or B.O.D. is the amount of dissolved oxygen needed by aerobic biological organisms in a body of water to ... quantitative test, although it is widely used as an indication of the organic quality of water.

Last Answer : The addition of gypsum to port-land cement helps in : (1) increasing the strength of cement (2) rapid setting of cement (3) preventing rapid setting of cement (4) reduction in the cost of cement

In trickling filter, B.O.D. is reduced to A. 30 to 40% B. 40 to 60% C. 60 to 80% D. 80 to 90%

Description : In trickling filter, B.O.D. is reduced to A. 30 to 40% B. 40 to 60% C. 60 to 80% D. 80 to 90%

Last Answer : ANS: C

Seed germination percentage of rough lemon is: a. 50-60% b. 60-70% c. 70-80% d. 80-90%

Description : Seed germination percentage of rough lemon is: a. 50-60% b. 60-70% c. 70-80% d. 80-90%

Last Answer : 60-70%

In citrus 80-90% of the active roots are present in the soil to a depth of: a. 25 cm b. 50 cm c. 75 cm d. 100 cm

Description : In citrus 80-90% of the active roots are present in the soil to a depth of: a. 25 cm b. 50 cm c. 75 cm d. 100 cm

Last Answer : 25 cm