Description : Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher
Last Answer : (B) Ball mill
Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill
Last Answer : (C) Tube mill
Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill
Last Answer : (B) Hammer crusher
Description : Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill
Last Answer : (C) Gyratory crusher
Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil
Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill
Description : For the preliminary breaking of hard rock, we use a (A) Gyratory crusher (B) Ball mill (C) Tube mill (D) Squirrel-cage disintegrator
Last Answer : (A) Gyratory crusher
Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher
Description : Which of the following gives the work required for size reduction of coal to -200 mesh in a ball mill most accurately? (A) Rittinger's law (B) Kick's law (C) Bond's law (D) None of these
Last Answer : (A) Rittinger's law
Description : Which of the following is not an ultrafine grinder (colloid mill)? (A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification
Last Answer : (C) Toothed roll crusher
Description : Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these
Last Answer : (B) Toothed roll
Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher
Last Answer : (B) Roll crusher
Description : To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill
Last Answer : (D) Fluid energy mill
Description : Use of pulverised coal in boilers provides (A) Higher calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace wall
Last Answer : (B) Better combustion
Description : Limestone powder is injected during pulverised coal burning in boilers to __________ the flue gases. (A) Reduce SO2 content in (B) Catalytically convert SO2 to SO3 in (C) Increase the dew point of (D) None of these
Last Answer : (A) Reduce SO2 content in
Description : Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill
Last Answer : (B) Squirrel-cage disintegrator
Description : Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher
Last Answer : (B) Gyratory crusher
Description : Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher
Description : Pulverised coal passing through 200 mesh screen has a diameter of 0.074 mm (74 micron). The same passing through 50 mesh screen will have a dia of __________ mm. (A) 0.007 (B) 0.30 (C) 50 (D) 0.014
Last Answer : (B) 0.30
Description : Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill
Last Answer : (B) Roller crusher
Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser
Last Answer : (C) Jaw crusher
Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher
Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill
Description : Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusher
Last Answer : (D) Jaw crusher
Description : Emission of dense white smoke out of the chimney of a thermal power plant is an indication of the use of (A) Less air for combustion (B) Correct amount of air for combustion (C) Too much air for combustion (D) Pulverised coal in boilers
Last Answer : (C) Too much air for combustion
Description : The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times
Last Answer : (B) 2.5 times
Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types
Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size
Description : For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a (A) Buhrstone mill (B) Ball mill (C) Crushing rolls (D) Hammer mill
Last Answer : (A) Buhrstone mill
Description : This type threasher consist of spike tooth cylinder, woven wire mesh concave and upper casing provide with helical louvers. a. Hammer mill c. Dummy d. None of above
Last Answer : Ans- b. Axial flow
Description : Reciprocating screens are normally inclined at an angle of 5° with the horizontal and employ gyratory motion at feed end & reciprocating motion at the discharge end. They are not suitable for the ... Dry chemicals (C) Heavy tonnages of rocks or gravel (D) Powdered food & granular materials
Last Answer : (C) Heavy tonnages of rocks or gravel
Description : Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls
Last Answer : (A) Hammer mills
Description : Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil
Last Answer : (D) Fluid energy mil
Description : Pick out the wrong statement. (A) Hammer crushers operate by impact action (B) Standard screens have circular opening (C) With increase in mesh number of screens, their diameter in microns decreases (D) 200 mesh screen has 200 openings per linear cm
Last Answer : (D) 200 mesh screen has 200 openings per linear cm
Description : The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting
Last Answer : (B) Compression
Description : Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these
Last Answer : (A) Jaw crusher
Description : According to Taggart's rule for selecting between a gyratory crusher and a jaw crusher; the later should be used, if the hourly tonnage to be crushed divided by the square of the gape expressed in cm is less than (A) 0.00184 (B) 0.0184 (C) 0.184 (D) 1.84
Last Answer : (B) 0.0184
Description : Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087
Last Answer : (B) 0.087 L.S
Description : Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure ... Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher
Last Answer : (B) Cake resistance is independent of the pressure drop
Description : Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers
Last Answer : (A) Rod mills
Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.
Last Answer : i)Tray dryer: ii)Plate column: iii)Packed column: iv) Jaw crusher: v) Stirrer: vi) Ball mill
Description : The advantages of firing pulverised coal in the furnace lies in the fact that, it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel consumption (D) All (A), (B) and (C)
Last Answer : (C) Accelerates the burning rate and economises on fuel consumption
Description : Use of pulverised coal in boiler furnace provides (A) High calorific value (B) Better combustion (C) Smokeless burning (D) Less erosion on furnace walls
Description : Function of secondary air in pulverised coal firing is to (A) Transport the coal to the burner (B) Dry the coal (C) Ensure efficient burning of coal around the burner (D) Reduce primary air requirement
Last Answer : (C) Ensure efficient burning of coal around the burner
Description : The advantage of firing pulverised coal in the furnace lies in the fact, that it (A) Permits the use of high ash content coal (B) Permits the use of low fusion point ash coal (C) Accelerates the burning rate and economises on fuel combustion (D) All (A), (B) and (C)
Last Answer : (C) Accelerates the burning rate and economises on fuel combustion
Description : A travelling grate stoker is meant for the efficient burning of __________ coal. (A) Caking (B) Pulverised (C) Non-caking (D) High ash
Last Answer : (C) Non-caking
Description : Which of the following fuels is the best for burning on chain grate stoker? (A) Non-caking coal (B) Caking coal (C) Coking coal (D) Pulverised coal
Last Answer : (A) Non-caking coal
Description : Coal is pulverised before burning in large capacity boiler furnaces mainly to (A) Ensure its complete combustion (B) Facilitate easy ash removal (C) Enhance its calorific value (D) Provide trouble free operation
Last Answer : (A) Ensure its complete combustion
Description : In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed (C) Clearance between hammer & grinding plates (D) All (A), (B) and (C
Last Answer : (D) All (A), (B) and (C
Description : . In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal
Last Answer : (D) Rotor shaft carrying hammers can be vertical or horizontal
Description : . To produce talcum powder, use (A) Ball mill (B) Hammer mill (C) Jet mill (D) Pin mill
Last Answer : (A) Ball mill