Description : Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill
Last Answer : (B) Squirrel-cage disintegrator
Description : Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the (A) Blake jaw crusher (B) Cage mill (C) Stamp mill (D) Bradford's breaker
Last Answer : (B) Cage mill
Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill
Last Answer : (C) Gyratory crusher
Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher
Last Answer : (B) Ball mill
Description : Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher
Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher
Description : Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill
Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil
Last Answer : (B) Hammer crusher
Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser
Last Answer : (C) Jaw crusher
Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill
Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill
Last Answer : (C) Tube mill
Description : Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these
Last Answer : (A) Jaw crusher
Description : Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher
Last Answer : (B) Gyratory crusher
Description : In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil
Last Answer : (D) Fluid energy mil
Description : To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill
Last Answer : (D) Fluid energy mill
Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher
Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill
Description : Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusher
Last Answer : (D) Jaw crusher
Description : A __________ mill is a revolving mill divided into two or more sections by perforated partitions in which preliminary grinding takes place at one end and the finishing grinding at the discharge end. (A) Compartment (B) Tube (C) Rod (D) Pebble
Last Answer : (A) Compartmen
Description : The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting
Last Answer : (B) Compression
Description : According to Taggart's rule for selecting between a gyratory crusher and a jaw crusher; the later should be used, if the hourly tonnage to be crushed divided by the square of the gape expressed in cm is less than (A) 0.00184 (B) 0.0184 (C) 0.184 (D) 1.84
Last Answer : (B) 0.0184
Description : The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times
Last Answer : (B) 2.5 times
Description : Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher
Last Answer : (C) Toothed roll crusher
Description : Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these
Last Answer : (B) Toothed roll
Description : Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087
Last Answer : (B) 0.087 L.S
Description : Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure ... Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher
Last Answer : (B) Cake resistance is independent of the pressure drop
Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types
Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size
Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher
Last Answer : (B) Roll crusher
Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.
Last Answer : i)Tray dryer: ii)Plate column: iii)Packed column: iv) Jaw crusher: v) Stirrer: vi) Ball mill
Description : __________ mill is not a revolving mill. (A) Pebble (B) Compartment (C) Cage (D) Tube
Last Answer : (C) Cage
Description : Which of the following is not an ultrafine grinder (colloid mill)? (A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification
Description : Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill
Last Answer : (B) Roller crusher
Description : Fluid energy mill comes in the category of (A) Grinder (B) Crusher (C) Cutter (D) Ultrafine grinder
Last Answer : (D) Ultrafine grinder
Description : A pebble mill (A) Is a ball mill (B) Employs flints or ceramic pebbles as the grinding medium (C) Is a tube mill lined with ceramic or other non-metallic liner (D) Both (B) and (C)
Last Answer : (D) Both (B) and (C)
Description : A tube mill as compared to a ball mill (A) Employs smaller balls (B) Gives finer size reduction but consumes more power (C) Has larger length/diameter ratio (>2 as compared to 1 for ball mill) (D) All (A), (B) and (C)
Description : Tube mill compared to ball mill (A) Produces finer products (B) Is long in comparison with its diameter (C) Uses smaller balls (D) All (A), (B) & (C)
Last Answer : (D) All (A), (B) & (C)
Description : The main differentiation factor between tube mill and ball mill is the (A) Length to diameter ratio (B) Size of the grinding media (C) Final product size (D) Operating speed
Last Answer : (A) Length to diameter ratio
Description : A tube mill compared to a ball mill (A) Has a higher length/diameter ratio (B) Produces a coarser product (C) Has a higher diameter/length ratio (D) Uses much larger balls
Last Answer : (A) Has a higher length/diameter ratio
Description : Can we add extra resistance in series with squirrel cage rotor? State the reason?
Last Answer : We cannot add extra resistance in series with the rotor because all the copper bars of the rotor are short circuited in both the sides by copper end rings to have a closed circuit.
Description : Squirrel cage induction motor has a) Zero starting torque b) Very small starting torque c) Medium starting torque d) Very high starting torque
Last Answer : Ans: B
Description : The speed of a squirrel-cage, multi-speed, induction motor, as used aboard ship, is varied by changing the __________. A. number of connected poles in the stator B. frequency to the motor C. excitation voltage D. resistance of the rotor circuit
Last Answer : Answer: A
Description : A four-pole, 60 cycle, squirrel-cage motor has a full load speed of 1725 RPM. What will be the percent of slip at full load? A. 4.16 B. 4.34 C. 95.66 D. 95.84
Description : Discoloration of the rotor bars in a squirrel-cage motor is typical evidence of _____________. A. moisture B. overheating C. vibration D. all of the above
Last Answer : Answer: B
Description : A split-phase induction squirrel-cage motor will not come up to speed, even though the rated voltage, rated frequency, and rated load are applied. The suspected trouble could be due to _____________. A. a faulty centrifugal switch B. broken rotor bars C. worn bearings D. all of the above
Last Answer : Answer: D
Description : A three-phase, squirrel cage, induction motor will run hot due to a/an ______________. A. improper brush position B. reversed commutating pole C. shorted stator D. high power factor
Last Answer : Answer: C
Description : A three-phase, squirrel cage, induction motor will run hot due to _____________. A. open stator coils B. high power factor C. dirty or corroded slip rings D. reversed commutating poles
Description : In the illustrated device, the part labeled '1A' _________. EL-0001 A. are start and run windings for a single phase shaded pole induction motor B. is the stator for a polyphase induction ... armature for a squirrel cage rotor motor D. are direct current shunt field windings for a universal motor
Description : In the illustration, the assembly labeled 2 is a ________. EL-0001 A. wound rotor and shaft for a single phase induction motor B. conduction rotor and shaft for a polyphase induction motor C. ... cage rotor and shaft for a polyphase motor D. squirrel cage rotor for a single phase induction motor
Description : The speed of a multi-speed, squirrel-cage, induction motor operating in a fixed frequency system can be changed by _____________. A. reconnecting stator windings for different numbers of poles B. ... sequence of the applied voltage D. reconnecting the stator so that no poles have the same polarity
Description : The speed of a squirrel-cage motor is usually changed by _____________. A. varying the frequency to the machine B. adding resistance in series with the stator windings C. adding resistance in parallel with the stator windings D. changing the number of connected poles in the stator