Description : Which of the following is not an ultrafine grinder (colloid mill)? (A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification
Last Answer : (C) Toothed roll crusher
Description : To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill
Last Answer : (D) Fluid energy mill
Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill
Last Answer : (C) Gyratory crusher
Description : __________ mill is not used for grinding wheat into flour and for milling of cereals & other vegetable products. (A) Buhrstone (B) Roller (C) Attrition (D) Pebble
Last Answer : (D) Pebble
Description : Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil
Last Answer : (D) Fluid energy mil
Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil
Last Answer : (B) Hammer crusher
Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill
Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher
Last Answer : (B) Ball mill
Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill
Last Answer : (C) Tube mill
Description : Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher
Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher
Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher
Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill
Description : Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusher
Last Answer : (D) Jaw crusher
Description : Fluid energy mill comes in the category of (A) Grinder (B) Crusher (C) Cutter (D) Ultrafine grinder
Last Answer : (D) Ultrafine grinder
Description : The grinding in a hammer crusher takes place due to the (A) Attrition (B) Impact (C) Both (A) & (B) (D) Neither (A) nor (B
Last Answer : (C) Both (A) & (B)
Description : In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) and (B)
Description : The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2. Spike tooth and wire loop type 3. Spike tooth and hammer mill 4. hammer mill and flails
Last Answer : ans 3
Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails
Last Answer : c) Spike tooth and hammer mill
Description : Maximum size reduction in a fluid energy mill is achieved by (A) Compression (B) Interparticle attrition (C) Cutting (D) Impact
Last Answer : (B) Interparticle attrition
Description : In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed (C) Clearance between hammer & grinding plates (D) All (A), (B) and (C
Last Answer : (D) All (A), (B) and (C
Description : . In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal
Last Answer : (D) Rotor shaft carrying hammers can be vertical or horizontal
Description : For the preliminary breaking of hard rock, we use a (A) Gyratory crusher (B) Ball mill (C) Tube mill (D) Squirrel-cage disintegrator
Last Answer : (A) Gyratory crusher
Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser
Last Answer : (C) Jaw crusher
Description : Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the (A) Blake jaw crusher (B) Cage mill (C) Stamp mill (D) Bradford's breaker
Last Answer : (B) Cage mill
Description : Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill
Description : Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill
Last Answer : (B) Squirrel-cage disintegrator
Description : Juice extraction capacity of vertical three roller type bullock down sugercane crusher E. 50-70% F. 70-90% G. 90-100% H. 30-50%
Last Answer : E. 50-70%
Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.
Last Answer : i)Tray dryer: ii)Plate column: iii)Packed column: iv) Jaw crusher: v) Stirrer: vi) Ball mill
Description : For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a (A) Buhrstone mill (B) Ball mill (C) Crushing rolls (D) Hammer mill
Last Answer : (A) Buhrstone mill
Description : . To produce talcum powder, use (A) Ball mill (B) Hammer mill (C) Jet mill (D) Pin mill
Last Answer : (A) Ball mill
Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)
Description : When removing ball or roller bearings from the shaft of a motor, you should use a _____________. A. rawhide hammer B. brass mallet C. wheel puller D. soft iron pry bar
Last Answer : Answer: C
Description : The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting
Last Answer : (B) Compression
Description : Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher (B) Cone crusher (C) Impact crusher (D) Toothed roll crushe
Last Answer : (B) Cone crusher
Description : Pick out the wrong statement. (A) More commonly used jaw crusher between Dodge jaw crusher and Blake jaw crusher is the later one (B) There are only four methods namely compression, impact ... Operating principles of Dodge and Blake jaw crushers are combined in the working of universal jaw crushers
Last Answer : (C) Cutting machines mainly employ 'attrition' for size reduction of solids
Description : This type threasher consist of spike tooth cylinder, woven wire mesh concave and upper casing provide with helical louvers. a. Hammer mill c. Dummy d. None of above
Last Answer : Ans- b. Axial flow
Description : This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above
Last Answer : Ans- b. Raspbar
Description : This type thresher consists of beater mounted on a shaft which rotates inside a closed casing and concave. a. Hammer mill b. Spike tooth d. None of above
Last Answer : Ans- c. Dummy
Description : Is hammer mill is similar to dummy type, but it is provided with aspirator for cleaning grains. A) True B) False
Last Answer : True
Description : A multi type thresher is equipped with a) Spike tooth cylinder b) Rasp bar cylinder c) Hammer mill cylinder d) All of the above
Last Answer : All of the above
Description : The dummy type thresher is also termed as a) Rasp bar type thresher b) Hammer mill type thresher c) Spike tooth type thresher d) Syndicator tooth type thresher
Last Answer : Hammer mill type thresher
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill
Last Answer : a) Raspbar type cylinder
Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill
Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder
Last Answer : (b) Spike tooth cylinder
Description : Give principle construction and working of hammer mill with neat diagram.
Last Answer : PRINCIPLE: Impact CONSTRUCTION: It consists of a stout metal casing enclosing to which four or more swinging hammer are attached. The lower part of the casing consists of a screen , through which ... are not fixed . The mill can produce coarse to moderately fine powder. DIAGRAM:
Description : Explain construction and working of Cutter mill or Hammer mill
Last Answer : CONSTRUCTION: It consists of a hopper at top and metal casing enclosing two sets of knives i.e. stationary knives attached to stator and rotating are attached to rotor. The lower part of the casing consists ... are not fixed. The mill can produce coarse to moderately fine powder DIAGRAM:
Description : Draw well labelled diagram of “triple roller mill”.
Last Answer : diagram of “triple roller mill”.
Description : Explain the construction and working of triple roller mill.
Last Answer : Construction: It consists of 3 rollers. Rollers are made up of hard abrasion resistant material. Rollers are arranged very close to each other's. Rollers are rotated at different speed & in ... A Scraper is provided to remove the material from roller no.3 Diagram:
Description : A fluid energy mill is used for (A) Cutting (B) Grinding (C) Ultra-grinding (D) Crushing
Last Answer : (C) Ultra-grinding