Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Carbon black is pulverised in a
(A) Hammer crusher
(B) Ball mill
(C) Roll crusher
(D) Gyratory crusher
by

1 Answer

Answer :

(B) Ball mill
by

Related questions

Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher(B) Ball mill(C) Roll crusher(D) Gyratory crusher

Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Last Answer : (B) Hammer crusher

Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Last Answer : (C) Tube mill

Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill

Description : Which of the following is a coarse crusher? (A) Smooth roll crusher (B) Toothed roll crusher (C) Gyratory crusher (D) Tube mill

Last Answer : (C) Gyratory crusher

Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Last Answer : (C) Gyratory crusher

For the preliminary breaking of hard rock, we use a (A) Gyratory crusher(B) Ball mill(C) Tube mill(D) Squirrel-cage disintegrator

Description : For the preliminary breaking of hard rock, we use a (A) Gyratory crusher (B) Ball mill (C) Tube mill (D) Squirrel-cage disintegrator

Last Answer : (A) Gyratory crusher

To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Which of the following is not an ultrafine grinder (colloid mill)?(A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Description : Which of the following is not an ultrafine grinder (colloid mill)? (A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Last Answer : (C) Toothed roll crusher

Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Last Answer : (B) Hammer crusher

To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Description : To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Last Answer : (D) Fluid energy mill

Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill

Description : Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill

Last Answer : (B) Squirrel-cage disintegrator

Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Description : Which of the following is used for primary crushing of very hard lumpy materials? (A) Toothed roll crusher (B) Gyratory crusher

Last Answer : (B) Gyratory crusher

Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher

Description : Which of the following is a fine crusher? (A) Blake jaw crusher (B) Gyratory crusher (C) Toothed roll crusher (D) Dodge jaw crusher

Last Answer : (C) Toothed roll crusher

Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Description : Size reduction of ice and gypsum can be accomplished suitably by a __________ crusher. (A) Blake jaw (B) Toothed roll (C) Gyratory (D) None of these

Last Answer : (B) Toothed roll

Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Description : Which of the following achieves the least reduction ratio for a given feed size? (A) Jaw crusher (B) Roll crusher (C) Cone crusher (D) Gyratory crusher

Last Answer : (B) Roll crusher

Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill

Description : Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill

Last Answer : (B) Roller crusher

Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Description : Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Last Answer : (D) Fluid energy mil

Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Last Answer : (C) Jaw crusher

Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill(B) Ball mill, Jaw crusher, Fluid energy mill(C) Fluid energy mill, Jaw crusher, Ball mill(D) Fluid energy mill, Ball mill, Jaw crusher

Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher

Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill

Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusherFeed size of ≥ 25 cms can be accepted by(A) Ball mill(B) Rod mill(C) Fluid energy mill(D) Jaw crusher

Description : Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusher

Last Answer : (D) Jaw crusher

The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting

Description : The material is crushed in a gyratory crusher by the action of (A) Impact (B) Compression (C) Attrition (D) Cutting

Last Answer : (B) Compression

Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these

Description : Which of the following comes in the category of primary crusher for hard and tough stone? (A) Jaw crusher (B) Cone crusher (C) Gyratory crusher (D) None of these

Last Answer : (A) Jaw crusher

According to Taggart's rule for selecting between a gyratory crusher and a jaw crusher; the later should be used, if the hourly tonnage to be crushed divided by the square of the gape expressed in cm is less than (A) 0.00184 (B) 0.0184 (C) 0.184 (D) 1.84

Description : According to Taggart's rule for selecting between a gyratory crusher and a jaw crusher; the later should be used, if the hourly tonnage to be crushed divided by the square of the gape expressed in cm is less than (A) 0.00184 (B) 0.0184 (C) 0.184 (D) 1.84

Last Answer : (B) 0.0184

The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Description : The capacity of a gyratory crusher is __________ that of a jaw crusher with the same gape, handling the same feed & for the same product size range. (A) Same as (B) 2.5 times (C) 5 times (D) 10 times

Last Answer : (B) 2.5 times

Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087

Description : Capacity (in tons/hr) of jaw/gyratory crusher is equal to (where, L = length of the receiving opening, cm S = greater width of the discharge opening, cm). (A) 0.01 L.S (B) 0.087 L.S (C) L.S (D) L.S/0.087

Last Answer : (B) 0.087 L.S

Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure drop (C) Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Description : Pick out the wrong statement. (A) For the compressible cake, voidage & the specific resistance of the cake can be assumed to be constant (B) Cake resistance is independent of the pressure ... Crushing of explosive materials are done by employing dry-grinding (D) Gyratory crusher is a coarse crusher

Last Answer : (B) Cake resistance is independent of the pressure drop

Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size (C) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Description : Pick out the wrong statement: (A) Magnetic separation method can be employed to treat both dry & wet ores (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed ... ) Gyratory crusher is used for coarse crushing (D) Screens are of stationary, moving and vibratory types

Last Answer : (B) Reduction ratio in crushing operation is defined as the ratio of minimum feed size to the maximum product size

Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Description : Draw symbol of (i) Tray Dryer (ii) Plate column (iii) Packed column (iv) Jaw crusher (v) Strirrer (vi) Ball mill.

Last Answer : i)Tray dryer:   ii)Plate column:    iii)Packed column:   iv) Jaw crusher:   v) Stirrer:   vi) Ball mill  

For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a(A) Buhrstone mill(B) Ball mill(C) Crushing rolls(D) Hammer mill

Description : For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a (A) Buhrstone mill (B) Ball mill (C) Crushing rolls (D) Hammer mill

Last Answer : (A) Buhrstone mill

. To produce talcum powder, use (A) Ball mill (B) Hammer mill (C) Jet mill (D) Pin mill

Description : . To produce talcum powder, use (A) Ball mill (B) Hammer mill (C) Jet mill (D) Pin mill

Last Answer : (A) Ball mill

Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls

Description : Size reduction of asbestos and mica is done by (A) Hammer mills (B) Rod mills (C) Gyratory crushers (D) Crushing rolls

Last Answer : (A) Hammer mills

The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Description : The term 'angle of nip' is concerned with the operation of the __________ crushers. (A) Jaw (B) Roll (C) Gyratory (D) None of these

Last Answer : (B) Roll

Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Description : Size reduction does not occur due to compression in case of (A) Rod mills (B) Gyratory crushers (C) Jaw crushers (D) Smooth roll crushers

Last Answer : (A) Rod mills

The grinding in a hammer crusher takes place due to the (A) Attrition (B) Impact (C) Both (A) & (B) (D) Neither (A) nor (B

Description : The grinding in a hammer crusher takes place due to the (A) Attrition (B) Impact (C) Both (A) & (B) (D) Neither (A) nor (B

Last Answer : (C) Both (A) & (B)

In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)

Description : In case of a hammer crusher, (A) Crushing takes place by impact breaking (B) Maximum acceptable feed size is 30 cms (C) Reduction ratio can be varied by adjusting the distance from cage to hammers (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed(C) Clearance between hammer & grinding plates(D) All (A), (B) and (C

Description : In case of a hammer crusher, the final product size depends on the (A) Feed rate (B) Rotor speed (C) Clearance between hammer & grinding plates (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

. In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Description : . In case of a hammer crusher, the (A) Feed may be highly abrasive (Moh's scale >5) (B) Minimum product size is 3 mm (C) Maximum feed size may be 50 mm (D) Rotor shaft carrying hammers can be vertical or horizontal

Last Answer : (D) Rotor shaft carrying hammers can be vertical or horizontal

Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the(A) Blake jaw crusher(B) Cage mill(C) Stamp mill(D) Bradford's breaker

Description : Size reduction of fibrous materials like wood, asbestos, mica etc. is done by a disintegrator exemplified by the (A) Blake jaw crusher (B) Cage mill (C) Stamp mill (D) Bradford's breaker

Last Answer : (B) Cage mill

Fluid energy mill comes in the category of (A) Grinder (B) Crusher (C) Cutter (D) Ultrafine grinder

Description : Fluid energy mill comes in the category of (A) Grinder (B) Crusher (C) Cutter (D) Ultrafine grinder

Last Answer : (D) Ultrafine grinder

Horsepower required for a roll crusher is directly proportional to its (A) Reduction ratio (B) Capacity(C) Both (A) & (B)(D) Neither (A) nor (B)

Description : Horsepower required for a roll crusher is directly proportional to its (A) Reduction ratio (B) Capacity (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

In a roll crusher, the specific power consumption and the production rate is affected by the (A) Reduction ratio (B) Differential roll speed (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : In a roll crusher, the specific power consumption and the production rate is affected by the (A) Reduction ratio (B) Differential roll speed (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

In a roll crusher, both the rolls (A) Have the same diameter (B) Are rotated towards each other (C) Run either at the same or different speeds (D) All (A), (B) and (C

Description : In a roll crusher, both the rolls (A) Have the same diameter (B) Are rotated towards each other (C) Run either at the same or different speeds (D) All (A), (B) and (C

Last Answer : (D) All (A), (B) and (C

Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)

Description : Half the angle of nip, (α), for a roll crusher is given by (where, dr, dp and df are diameters of crushing rolls, feed particles and rolls gap respectively). (A) cos α = (dr + dp)/(dr + df) (B) cos α = (dr + df)/(dr + dp) (C) tan α = (dr + dp)/(dr + df) (D) sin α = (dr + dp)/(dr + df)

Last Answer : (A) cos α = (dr + dp)/(dr + df)

Pick out the correct statement: (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products (B) The operating cost of shaking screen is more than that of a vibrating screen (C) Screen capacity does not depend upon the specific gravity of the minerals (D) Asphalt is best crushed using toothed roll crusher

Description : Pick out the correct statement: (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products (B) The operating cost of ... upon the specific gravity of the minerals (D) Asphalt is best crushed using toothed roll crusher

Last Answer : (A) Removal of iron from ceramic material is necessitated (by magnetic separation method) so as to avoid discolouration of ceramic products

Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher(B) Cone crusher(C) Impact crusher(D) Toothed roll crushe

Description : Which is a secondary crusher for a hard & tough stone? (A) Jaw crusher (B) Cone crusher (C) Impact crusher (D) Toothed roll crushe

Last Answer : (B) Cone crusher

The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2. Spike tooth and wire loop type 3. Spike tooth and hammer mill 4. hammer mill and flails

Description : The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2. Spike tooth and wire loop type 3. Spike tooth and hammer mill 4. hammer mill and flails

Last Answer : ans 3

This type threasher consist of spike tooth cylinder, woven wire mesh concave and upper casing provide with helical louvers. a. Hammer mill c. Dummy d. None of above

Description : This type threasher consist of spike tooth cylinder, woven wire mesh concave and upper casing provide with helical louvers. a. Hammer mill c. Dummy d. None of above

Last Answer : Ans-    b. Axial flow

This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above

Description : This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above

Last Answer : Ans-    b. Raspbar