Description : The critical speed of a trommel (N) is related to its dia (D) as (A) N ∝ 1/√D (B) N ∝ √D (C) N ∝ D (D) N ∝ 1/D
Last Answer : (A) N ∝ 1/√D
Description : Mass flow of granular solid (M) through a circular opening of dia, D follows (A) M ∝ √D (B) M ∝ D2 (C) M ∝ D3 (D) M ∝ D
Last Answer : (C) M ∝ D
Description : Optimum ratio of operating speed to critical speed of a trommel is (A) 0.33-0.45 (B) 1.33-1.45 (C) 0.5-2 (D) 1.5-2.5
Last Answer : (A) 0.33-0.45
Description : Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N
Last Answer : (A) D = 1840 H0.5 /N
Description : What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls? (A) 0.5 (B) 1.0 (C) 2.76 (D) 0.66
Last Answer : (D) 0.66
Description : For a sphere falling in the constant drag co-efficient regime, its terminal velocity depends on its diameter (D) as (A) d (B) √d (C) d 2 (D) 1/d
Last Answer : (C) d
Description : At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 ... Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0
Last Answer : (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5
Description : A bullet is fired vertically upwards with a velocity of 2200 ft/s. Bullet ascends to a height of a.56,900 ft b.107 dynes c.75,000 ft d.48.300 ft e.65,800 ft
Last Answer : c. 75,000 ft
Description : What is transit time (time delay) of a 50-ft length transmission line of the above problem? A. 50 ns B. 100 ns C. 75 ns D. 65 ns
Last Answer : C. 75 ns
Description : For spheres, the surface shape factor is given by (where, A = area, V = volume, and D = diameter) (A) π = (A/D2 ) (B) π/6 = (V/D3 ) (C) AD/V (D) None of these
Last Answer : (A) π = (A/D2 )
Description : A compound pipe of diameter d1, d2 and d3 having lengths l1, l2 and l3 is to be replaced by an equivalent pipe of uniform diameter d and of the same length (l) as that of the compound pipe. The size of the equivalent pipe is given by (A) l/d² = + + (B) l/d³ = + ) + (C) = + + (D)
Last Answer : Answer: Option D
Description : Rotor shaft of a large electric motor supported between short bearings at both ends shows a deflection of 1.8 mm in middle of motor. Assuming rotor to be perfectly balanced and supported at knife edges at both ends, likely critical speed (rpm) of shaft isA 350 B 4430 C 705 D 2810
Last Answer : C 705
Description : Power required to drive a ball mill with a particular ball load is proportional to (where, D = diameter of ball mill.) (A) D (B) 1/D (C) D2.5 (D) 1/D2.5
Last Answer : (C) D2.5 (D) 1/D2
Description : The specific surface of spherical particles is proportional to (where, Dp = diameter of particle). (A) D2 p (B) Dp (C) 1/Dp (D) 1/D2p
Last Answer : (C) 1/Dp
Description : In a fully turbulent flow (Re > 10 5 ) in a pipe of diameter 'd', for a constant pressure gradient, the dependence of volumetric flow rate of an incompressible fluid is (A) d (B) d 2 (C) d 2.5 (D) d
Last Answer : (C) d 2.5
Description : For pipe flows, head is proportional to __________ at constant capacity(where, D = pipe diameter). (A) 1/D (B) 1/D2 (C) 1/D5 (D) D
Last Answer : (C) 1/D5
Description : Which of the following is not an industrial screening equipment? (A) Sharpies centrifuge (B) Vibrating screen (C) Grizzly (D) Trommel
Last Answer : (A) Sharpies centrifug
Description : For sizing of fine materials, the most suitable equipment is a (A) Trommel (B) Grizzly (C) Shaking screen (D) Vibrating screen
Last Answer : (D) Vibrating screen
Description : The mass transfer co-efficient for a solid sphere of radius 'a' dissolving in a large volume of quiescent liquid, in which ‘D’ is the diffusivity of solute, is (A) D/a (B) D/2a (C) Proportional to √D (D) Dependent on the Reynolds number
Last Answer : (D) Dependent on the Reynolds number
Description : A wheel 8 mts in diameter coasts to rest from a speed of 800 rpm in 10 minutes. Its angular deceleration is a.308/min2 b.683 rad/min2 c.502 rad/min2 d.107 dynes e.809 rad/min2
Last Answer : c. 502 rad/min2
Description : Actual operating speed of a ball mill may vary from 65 to 80% of the critical speed. Which of the following duties would require the ball mill to be operated at maximum percentage of critical speed? (A) ... of large particles (upto 1.25 cms) (D) Dry grinding of large particles in un-baffed mills
Last Answer : (D) Dry grinding of large particles in un-baffed mills
Description : The average age of the men in a team is 76 years and that of the women is 75 years. The average age for the whole team is. A) 75 yrs B) 75.5 yrs C) Cannot be computed with the given information D) None of the above
Last Answer : C) Clearly to find the average, we ought to number of men, women or total persons in the class, neither of which has been given. So the data provided is inadequate.
Description : The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D
Last Answer : (c) π/4fs(D4-d4)/D
Description : Discharge from a 24 inch pipe of water at 10 ft/sec will be __________ ft 3 /sec. (A) 7.65 (B) 32.36 (C) 48.22 (D) 125.6
Last Answer : (D) 125.6
Description : Trommels are revolving screens which normally operate in the range of __________ rpm. (A) 1 - 2 (B) 15 - 20 (C) 40 - 50 (D) 60 - 75
Last Answer : (B) 15 - 20
Description : The peripheral velocity at inlet of a centrifugal pump having inlet diameter of 25 cms and rotating at 950 rpm is __________ m/sec. (A) 1.8 (B) 12.4 (C) 186.2 (D) 736.4
Last Answer : (B) 12.4
Description : A giraffe can one 525 m in 75 seconds and everything can one 260 m in 65 seconds find the speed of the elephant in meters per second.?
Last Answer : 48 we
Description : Calculate damped natural frequency, if a spring mass damper system is subjected to periodic disturbing force of 30 N. Damping coefficient is equal to 0.76 times of critical damping coefficient and undamped natural frequency is 5 rad/sec A. 3.99 rad/sec B. 2.13 rad/sec C. 4.12 rad/sec D. 3.24 rad/sec
Last Answer : D. 3.24 rad/sec
Description : If d is the diameter of a bar, ft is allowable tensile stress and fb, is allowable bond stress, the bond length is given by (A) ft .d/4fb (B) ( /4). (ft .d/fb) (C) ft .d²/fb (D) ( /4). (ft .d 3 /fb)
Last Answer : Answer: Option A
Description : How many feet and inches are in 76.75 inches?
Last Answer : 6 feet, 4.75 inches
Description : Assume postal rates for 'light letters' are: $0.25 up to 10 grams; $0.35 up to 50 grams; $0.45 up to 75 grams; $0.55 up to 100 grams. Which test inputs (in grams) would be selected using boundary value analysis? A. 0, 9,19, ... C. 0, 1,10,11, 50, 51, 75, 76,100,101 D. 25, 26, 35, 36, 45, 46, 55, 56
Last Answer : C. 0, 1,10,11, 50, 51, 75, 76,100,101
Description : The energy consumption and production patterns in a chemical plant over a 9 month period is provided in the table below; Month 1 2 3 4 5 6 7 8 9 Production in Tonnes / month 493 ... and give your inference on the result ? ( consider 9 month data for evaluation for predicted energy consumption)
Last Answer : It is required to use the equations Y= mX + C and nC + mΣX = ΣY cΣX + mΣX2 = ΣXY Month X = Production in Tonnes / month Y =Energy Consumption MWh /month X 2 XY 1 493 78.2 ... 73.7 54756 17240.63 8 239 64.4 57121 15402.96 9 239 72.1 57121 17228.98 3387 665.3 1410683 253221
Description : What is the number that comes next in the sequence? 2, 5, 9, 19, 37, __ (A) 76 (B) 74 (C) 75 (D) 50
Last Answer : Answer: C
Description : The next number in the series 2, 5, 9, 19, 37, ? will be (A) 74 (B) 75 (C) 76 (D) None of the above
Last Answer : Answer: B 2 * 2 = 4 + 1 = 5, 5 * 2 = 10 - 1 = 9, 9 * 2 = 18 +1 = 19, 19*2 = 38 - 1 = 37, 37*2 = 74 + 1= 75.
Description : Is a 56 ft 65 ft 16ft triangle a right angle triangle?
Last Answer : The ratio of the length of the side of a right angle trianglemust be 3,4,516,56,65are not in that ratio.
Description : Is 56 ft 65 ft 16 ft a triangle?
Last Answer : Yes, the three given lengths will form a triangle.Three lengths can make a triangle if, and only if, the sum ofthe two shorter lengths is greater than the longest length.The two shorter lengths are 56 ft and 16 ft ... = 72 ft72 ft is greater than 65 ft so 56 ft, 65 ft and 16 ft will makea triangle.
Description : Is a 65 inch TV too big for my 5 ft. wall?
Last Answer : Yes, there are 12 inches in one foot, which means that your wall is 60 inches wide. The 65 inch TV will be too large to fit on your wall. I would suggest finding a TV that is a bit smaller.
Description : About 2-3 hp, power per gallon of a thin liquid provides vigorous agitation in an agitator. 'Power number' in agitation is given by (A) P. gc /n 3 . D2 . ρ (B) P. gc . ρ/µ
Last Answer : (A) P. gc /n 3 . D2 . ρ
Description : For spheres, volume shape factor is given by (A) π = (A/D2 ) (B) 2π = (2A/D2 ) (C) π/6 = (V/D3 ) (D) AD/V
Last Answer : (C) π/6 = (V/D3 )
Description : A flywheel 200 cm in diameter is rotating at 100 rpm. A point on the rim of the flywheel will not have a.angular velocity b.centripental acceleration c.tangential acceleration d.all of the above e.107 dynes
Last Answer : c. tangential acceleration
Description : What is the total acceleration of a point on the rim of a flywheel 4 mts in diameter 0.6 see after it has started from rest if it accelarates uniformly from rest to 2000 rpm in 20 secs. a.68.9 mts/sec2 b.102.6 mts/sec2 c.78.94 mts/sec2 d.107 dynes e.33.2 mts/sec2
Last Answer : c. 78.94 mts/sec2
Description : A flywheel 200 cm in diameter is rotating at 100 rpm. A point one the rim of the flywheel will not have a.angular velocity b.centripetal acceleration c.tangential acceleration d.all of the above e.107 dynes
Last Answer : a. angular velocity
Description : A sliding contact bearing is operating under stable condition. The pressure developed in oil film is p when the journal rotates at N rpm. The dynamic viscosity of lubricant is μ and effective coefficient of ... to p and f) (d) f is directly proportional to μ and inversely proportional to N
Last Answer : (b) f is directly proportional to μ and N
Description : A hollow shaft of 1 m length is designed to transmit a power of 30 kW at 700 rpm. The maximum permissible angle of twist in the shaft is 1o. The inner diameter of the shaft is 0.7 times the outer diameter. The modulus of ... shaft is _______. (a) 43 to 45 (b) 50to 60 (c) 70 to 80 (d) 85 to 100
Last Answer : (a) 43 to 45
Description : power of absorbing type hydraulic dynamometer varies as a) cube of rpm b) fifth power of the diameter c) none of the above d) both (a) and (b)
Last Answer : d) both (a) and (b)
Description : The critical pressure at which the latent heat of vaporisation of steam becomes zero is __________ Kg/cm2. (A) 273.15 (B) 225.65 (C) 100.03 (D) 373.15
Last Answer : (B) 225.65
Description : The factor which affects critical speed shaft is....... A. eccentricity B. span of shaft C. diameter of disc D. all of above
Last Answer : D. all of above
Description : The critical speed of a shaft is affected by A. Diameter of the disc B. Eccentricity C. Span of shaft D. All of above
Last Answer : D. All of above
Description : The factors which affects the critical speed of the shaft is A. Eccentricity B. Diameter of the Disc C. Span of the shaft D. All the above
Last Answer : D. All the above