. To produce talcum powder, use (A) Ball mill (B) Hammer mill (C) Jet mill (D) Pin mill

. To produce talcum powder, use
(A) Ball mill
(B) Hammer mill
(C) Jet mill
(D) Pin mill
by

1 Answer

Answer :

(A) Ball mill
by

Related questions

Property responsible for the talcum powder to cling to the skin is the (A) Capillary action (B) Adhesion (C) Cohesion (D) Surface tension

Description : Property responsible for the talcum powder to cling to the skin is the (A) Capillary action (B) Adhesion (C) Cohesion (D) Surface tension

Last Answer : Option B

Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Last Answer : (B) Hammer crusher

For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a(A) Buhrstone mill(B) Ball mill(C) Crushing rolls(D) Hammer mill

Description : For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a (A) Buhrstone mill (B) Ball mill (C) Crushing rolls (D) Hammer mill

Last Answer : (A) Buhrstone mill

To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Description : To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Last Answer : (D) Fluid energy mill

Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Last Answer : (B) Hammer crusher

Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher(B) Ball mill(C) Roll crusher(D) Gyratory crusher

Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Last Answer : (C) Tube mill

Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Description : Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Talcum powder poisoning?

Description : Talcum powder poisoning?

Last Answer : DefinitionTalcum powder is a powder made from a purified mineral called talc. Talcum powder poisoning may occur when someone accidentally or intentionally breathes in or swallows talcum powder.This is ... talc.SymptomsMost symptoms are caused by accidental or long-term breathing in (inhaling) of ta

We often sprinkle talcum powder on the carom board . This is done to reduce ______ between the board and the striker. a) friction b)movement c)speed d)contact

Description : We often sprinkle talcum powder on the carom board . This is done to reduce ______ between the board and the striker. a) friction b)movement c)speed d)contact

Last Answer : a) friction

Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Last Answer : (C) Jaw crusher

To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Which of the following is not an ultrafine grinder (colloid mill)?(A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Description : Which of the following is not an ultrafine grinder (colloid mill)? (A) Micronizers (B) Agitated mills and fluid energy mills (C) Toothed roll crusher (D) Hammer mills with internal classification

Last Answer : (C) Toothed roll crusher

The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : The mechanism of size reduction by a hammer mill is by impact and attrition between the (A) Grinding element & the housing (B) Feed particles (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) and (B)

Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill

Description : Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill

Last Answer : (B) Roller crusher

The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2. Spike tooth and wire loop type 3. Spike tooth and hammer mill 4. hammer mill and flails

Description : The two types of cylinders used on power wheat threshers are 1. Serrated disc and rasp bar 2. Spike tooth and wire loop type 3. Spike tooth and hammer mill 4. hammer mill and flails

Last Answer : ans 3

This type threasher consist of spike tooth cylinder, woven wire mesh concave and upper casing provide with helical louvers. a. Hammer mill c. Dummy d. None of above

Description : This type threasher consist of spike tooth cylinder, woven wire mesh concave and upper casing provide with helical louvers. a. Hammer mill c. Dummy d. None of above

Last Answer : Ans-    b. Axial flow

This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above

Description : This type thresher consists of corrugated bars are mounted axially on pheripheri of the cylinder. a. Hammer mill c. Dummy d. None of above

Last Answer : Ans-    b. Raspbar

This type thresher consists of beater mounted on a shaft which rotates inside a closed casing and concave. a. Hammer mill b. Spike tooth d. None of above

Description : This type thresher consists of beater mounted on a shaft which rotates inside a closed casing and concave. a. Hammer mill b. Spike tooth d. None of above

Last Answer : Ans-                             c. Dummy

Is hammer mill is similar to dummy type, but it is provided with aspirator for cleaning grains. A) True B) False

Description : Is hammer mill is similar to dummy type, but it is provided with aspirator for cleaning grains. A) True B) False

Last Answer : True

A multi type thresher is equipped with a) Spike tooth cylinder b) Rasp bar cylinder c) Hammer mill cylinder d) All of the above

Description : A multi type thresher is equipped with a) Spike tooth cylinder b) Rasp bar cylinder c) Hammer mill cylinder d) All of the above

Last Answer : All of the above

The dummy type thresher is also termed as a) Rasp bar type thresher b) Hammer mill type thresher c) Spike tooth type thresher d) Syndicator tooth type thresher

Description : The dummy type thresher is also termed as a) Rasp bar type thresher b) Hammer mill type thresher c) Spike tooth type thresher d) Syndicator tooth type thresher

Last Answer : Hammer mill type thresher

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Description : The two types of cylinder used on power wheat threshers are: a) Serrated disc and rasp bar b) Spike tooth and wire loop type c) Spike tooth and hammer mill d) Hammer mill and flails

Last Answer : c) Spike tooth and hammer mill

Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Description : Axial flow thresher uses a) Raspbar type cylinder b) Serrated disc type cylinder c) Spike tooth d) Hammer mill

Last Answer : a) Raspbar type cylinder

Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Description : Axial flow thresher utilises (a) Rasp bar cylinder (b) Spike tooth cylinder (c) Hammer mill cylinder (d) Peg tooth cylinder

Last Answer : (b) Spike tooth cylinder

Give principle construction and working of hammer mill with neat diagram.

Description : Give principle construction and working of hammer mill with neat diagram.

Last Answer : PRINCIPLE: Impact CONSTRUCTION: It consists of a stout metal casing enclosing to which four or more swinging hammer are attached. The lower part of the casing consists of a screen , through which ... are not fixed . The mill can produce coarse to moderately fine powder. DIAGRAM:

Explain construction and working of Cutter mill or Hammer mill

Description : Explain construction and working of Cutter mill or Hammer mill

Last Answer : CONSTRUCTION: It consists of a hopper at top and metal casing enclosing two sets of knives i.e. stationary knives attached to stator and rotating are attached to rotor. The lower part of the casing consists ... are not fixed. The mill can produce coarse to moderately fine powder DIAGRAM:  

Which of the following size reduction equipments employs mainly attrition for ultrafine grinding? (A) Jet mills (B) Fluid energy mill (C) Micronizer (D) All (A), (B) and (C)

Description : Which of the following size reduction equipments employs mainly attrition for ultrafine grinding? (A) Jet mills (B) Fluid energy mill (C) Micronizer (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Pick up the correct statement from the following: (A) Air lift pumps are generally used for pumping water from deep wells (B) Jet pumps are generally used for pumping water from small wells (C) The hydraulic ram works on the principle of water hammer (D) All the above

Description : Pick up the correct statement from the following: (A) Air lift pumps are generally used for pumping water from deep wells (B) Jet pumps are generally used for pumping water from small wells (C) The hydraulic ram works on the principle of water hammer (D) All the above

Last Answer : (D) All the above

Mixing of light fine powder such as insecticides is done by (A) Banbury mixer (B) Pug mill (C) Impact wheels (D) Kneader

Description : Mixing of light fine powder such as insecticides is done by (A) Banbury mixer (B) Pug mill (C) Impact wheels (D) Kneader

Last Answer : (C) Impact wheels

In AT welding process what is the role of asbestos powder & slag ? (i) To separate closing pin from portion* (ii) To hold the portion (iii) Both above are correct (iv) None of the above

Description : In AT welding process what is the role of asbestos powder & slag ? (i) To separate closing pin from portion* (ii) To hold the portion (iii) Both above are correct (iv) None of the above

Last Answer : (i) To separate closing pin from portion*

In AT welding process what is the role of closing pin ? (i) To hold the portion before melt (ii) To hold the asbestos powder & slag (iii) Both above are correct* (iv) None of the above

Description : In AT welding process what is the role of closing pin ? (i) To hold the portion before melt (ii) To hold the asbestos powder & slag (iii) Both above are correct* (iv) None of the above

Last Answer : (iii) Both above are correct*

How many grams asbestos powder is used to cover head of closing pin ? (i) 2 grams (ii) 3 grams (iii) 4 grams (iv) 5 grams*

Description : How many grams asbestos powder is used to cover head of closing pin ? (i) 2 grams (ii) 3 grams (iii) 4 grams (iv) 5 grams*

Last Answer : (iv) 5 grams*

Head of closing pin is covered with (i) Asbestos powder (ii) Slag Powder (iii) Asbestos powder than slag* (iv) None of above

Description : Head of closing pin is covered with (i) Asbestos powder (ii) Slag Powder (iii) Asbestos powder than slag* (iv) None of aboveove

Last Answer : iii) Asbestos powder than slag*

For the preliminary breaking of hard rock, we use a (A) Gyratory crusher(B) Ball mill(C) Tube mill(D) Squirrel-cage disintegrator

Description : For the preliminary breaking of hard rock, we use a (A) Gyratory crusher (B) Ball mill (C) Tube mill (D) Squirrel-cage disintegrator

Last Answer : (A) Gyratory crusher

Which of the following gives the work required for size reduction of coal to -200 mesh in a ball mill most accurately? (A) Rittinger's law (B) Kick's law (C) Bond's law (D) None of these

Description : Which of the following gives the work required for size reduction of coal to -200 mesh in a ball mill most accurately? (A) Rittinger's law (B) Kick's law (C) Bond's law (D) None of these

Last Answer : (A) Rittinger's law

Power required to drive a ball mill with a particular ball load is proportional to (where, D = diameter of ball mill.) (A) D (B) 1/D (C) D2.5 (D) 1/D2.5

Description : Power required to drive a ball mill with a particular ball load is proportional to (where, D = diameter of ball mill.) (A) D (B) 1/D (C) D2.5 (D) 1/D2.5

Last Answer : (C) D2.5 (D) 1/D2

A pebble mill (A) Is a ball mill (B) Employs flints or ceramic pebbles as the grinding medium (C) Is a tube mill lined with ceramic or other non-metallic liner (D) Both (B) and (C)

Description : A pebble mill (A) Is a ball mill (B) Employs flints or ceramic pebbles as the grinding medium (C) Is a tube mill lined with ceramic or other non-metallic liner (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

For achieving maximum capacity of the ball mill, the ball charge should be equal to about __________ percent of the ball mill volume. (A) 10 (B) 25 (C) 50 (D) 75

Description : For achieving maximum capacity of the ball mill, the ball charge should be equal to about __________ percent of the ball mill volume. (A) 10 (B) 25 (C) 50 (D) 75

Last Answer : (C) 50

Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Last Answer : (C) Gyratory crusher

Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Description : Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Last Answer : (D) Fluid energy mil

A tube mill as compared to a ball mill (A) Employs smaller balls (B) Gives finer size reduction but consumes more power (C) Has larger length/diameter ratio (>2 as compared to 1 for ball mill) (D) All (A), (B) and (C)

Description : A tube mill as compared to a ball mill (A) Employs smaller balls (B) Gives finer size reduction but consumes more power (C) Has larger length/diameter ratio (>2 as compared to 1 for ball mill) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In case of grinding in a ball mill (A) Wet grinding achieves a finer product size than dry grinding (B) Its capacity decreases with increasing fineness of the products (C) Grinding cost and power requirement increases with increasing fineness of the products (D) All (A), (B) and (C)

Description : In case of grinding in a ball mill (A) Wet grinding achieves a finer product size than dry grinding (B) Its capacity decreases with increasing fineness of the products (C) Grinding cost and power requirement increases with increasing fineness of the products (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls? (A) 0.5 (B) 1.0 (C) 2.76 (D) 0.66

Description : What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls? (A) 0.5 (B) 1.0 (C) 2.76 (D) 0.66

Last Answer : (D) 0.66

Tube mill compared to ball mill (A) Produces finer products (B) Is long in comparison with its diameter (C) Uses smaller balls (D) All (A), (B) & (C)

Description : Tube mill compared to ball mill (A) Produces finer products (B) Is long in comparison with its diameter (C) Uses smaller balls (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

The energy consumed by a ball mill depends on (A) Its speed (B) Its ball load (C) The density of the material being ground (D) All (A), (B) and (C)

Description : The energy consumed by a ball mill depends on (A) Its speed (B) Its ball load (C) The density of the material being ground (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Description : In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Last Answer : (A) Db 2 = K.Df

__________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Description : __________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Last Answer : (B) Minimum size