The energy consumed by a ball mill depends on (A) Its speed (B) Its ball load (C) The density of the material being ground (D) All (A), (B) and (C)

The energy consumed by a ball mill depends on
(A) Its speed
(B) Its ball load
(C) The density of the material being ground
(D) All (A), (B) and (C)
by

1 Answer

Answer :

(D) All (A), (B) and (C)
by

Related questions

Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Description : Energy requirement (per unit mass of material crushed/ground) is highest for (A) Jaw crusher (B) Rod mill (C) Ball mill (D) Fluid energy mil

Last Answer : (D) Fluid energy mil

Power required to drive a ball mill with a particular ball load is proportional to (where, D = diameter of ball mill.) (A) D (B) 1/D (C) D2.5 (D) 1/D2.5

Description : Power required to drive a ball mill with a particular ball load is proportional to (where, D = diameter of ball mill.) (A) D (B) 1/D (C) D2.5 (D) 1/D2.5

Last Answer : (C) D2.5 (D) 1/D2

Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill

Description : Fibrous material is broken by a (A) Roll-crusher (B) Squirrel-cage disintegrator (C) Ball mill (D) Tube mill

Last Answer : (B) Squirrel-cage disintegrator

Liners of a ball mill are never made of (A) Lead (B) Alloy steel (C) Rubber or ceramic material (D) Cast iron

Description : Liners of a ball mill are never made of (A) Lead (B) Alloy steel (C) Rubber or ceramic material (D) Cast iron

Last Answer : (A) Lead

What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls? (A) 0.5 (B) 1.0 (C) 2.76 (D) 0.66

Description : What is the critical rotation speed in revolutions per second, for a ball mill of 1.2 m diameter charged with 70 mm dia balls? (A) 0.5 (B) 1.0 (C) 2.76 (D) 0.66

Last Answer : (D) 0.66

The main differentiation factor between tube mill and ball mill is the (A) Length to diameter ratio (B) Size of the grinding media (C) Final product size (D) Operating speed

Description : The main differentiation factor between tube mill and ball mill is the (A) Length to diameter ratio (B) Size of the grinding media (C) Final product size (D) Operating speed

Last Answer : (A) Length to diameter ratio

The operating speed of a ball mill should be __________ the critical speed. (A) Less than (B) Much more than (C) At least equal to (D) Slightly more than

Description : The operating speed of a ball mill should be __________ the critical speed. (A) Less than (B) Much more than (C) At least equal to (D) Slightly more than

Last Answer : (A) Less than

Actual operating speed of a ball mill may vary from 65 to 80% of the critical speed. Which of the following duties would require the ball mill to be operated at maximum percentage of critical speed? (A) Wet grinding in low viscous suspension (B) Wet grinding in high viscous suspension (C) Dry grinding of large particles (upto 1.25 cms) (D) Dry grinding of large particles in un-baffed mills

Description : Actual operating speed of a ball mill may vary from 65 to 80% of the critical speed. Which of the following duties would require the ball mill to be operated at maximum percentage of critical speed? (A) ... of large particles (upto 1.25 cms) (D) Dry grinding of large particles in un-baffed mills

Last Answer : (D) Dry grinding of large particles in un-baffed mills

Critical Speed (Nc ) of a ball mill is given by (where R1 and R2 are radii of ball mill and the ball respectively). (A) Nc = (1/4π). √(g/R1 - R2 ) (B) Nc = (1/2π). √(g/R1 - R2 ) (C) Nc = (1/π). √(g/R1 - R2 ) (D) Nc = (1/2π). √(R1 - R2 /g)

Description : Critical Speed (Nc ) of a ball mill is given by (where R1 and R2 are radii of ball mill and the ball respectively). (A) Nc = (1/4π). √(g/R1 - R2 ) (B) Nc = (1/2π). √(g/R1 - R2 ) (C) Nc = (1/π). √(g/R1 - R2 ) (D) Nc = (1/2π). √(R1 - R2 /g)

Last Answer : (B) Nc = (1/2π). √(g/R1 - R2 )

In case of a ball mill, (A) Coarse feed requires a larger ball (B) Fine feed requires a larger ball (C) Operating speed should be more than the critical speed (D) None of these

Description : In case of a ball mill, (A) Coarse feed requires a larger ball (B) Fine feed requires a larger ball (C) Operating speed should be more than the critical speed (D) None of these

Last Answer : (A) Coarse feed requires a larger ball

Width and speed of a conveyor belt depends upon the __________ of the material. (A) Lump size (B) Bulk density (C) Both (A) & (B) (D) Neither (A) nor (B

Description : Width and speed of a conveyor belt depends upon the __________ of the material. (A) Lump size (B) Bulk density (C) Both (A) & (B) (D) Neither (A) nor (B

Last Answer : (C) Both (A) & (B)

Temperature of the product during ultrafine grinding (A) Increases (B) Decreases (C) Remain constant (D) May increase or decrease; depends on the material being ground

Description : Temperature of the product during ultrafine grinding (A) Increases (B) Decreases (C) Remain constant (D) May increase or decrease; depends on the material being ground

Last Answer : (A) Increases

Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Description : Which of the following crushers can be considered as a combination of a jaw crusher and a roller crusher? (A) Rod mill (B) Fluid energy mill (C) Gyratory crusher (D) Ball mill

Last Answer : (C) Gyratory crusher

To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Description : To get ultrafine particles, the equipment used is a (A) Ball mill (B) Rod mill (C) Hammer crusher (D) Fluid energy mill

Last Answer : (D) Fluid energy mill

Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill(B) Ball mill, Jaw crusher, Fluid energy mill(C) Fluid energy mill, Jaw crusher, Ball mill(D) Fluid energy mill, Ball mill, Jaw crusher

Description : Arrange the following size reduction equipment in the decreasing order of the average particle size produced by each of them. (A) Jaw crusher, Ball mill, Fluid energy mill (B) Ball mill, Jaw crusher, Fluid ... C) Fluid energy mill, Jaw crusher, Ball mill (D) Fluid energy mill, Ball mill, Jaw crusher

Last Answer : (A) Jaw crusher, Ball mill, Fluid energy mill

Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusherFeed size of ≥ 25 cms can be accepted by(A) Ball mill(B) Rod mill(C) Fluid energy mill(D) Jaw crusher

Description : Feed size of ≥ 25 cms can be accepted by (A) Ball mill (B) Rod mill (C) Fluid energy mill (D) Jaw crusher

Last Answer : (D) Jaw crusher

Compute the power consumed by a material with current density 15 units in an area of 100 units. The potential measured across the material is 20V. a) 100kJ b) 250kJ c) 30kJ d) 15kJ

Description : Compute the power consumed by a material with current density 15 units in an area of 100 units. The potential measured across the material is 20V. a) 100kJ b) 250kJ c) 30kJ d) 15kJ

Last Answer : c) 30kJ

Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill

Description : Wheat is ground into flour in a (A) Hammer crusher (B) Roller crusher (C) Impact mill (D) Fluid energy mill

Last Answer : (B) Roller crusher

When all the limiting reactant is consumed in the reaction, the operational yield __________ the relative yield. (A) Is greater than (B) Is smaller than (C) Equals (D) Can be either greater or smaller than (depends on the type of reaction)

Description : When all the limiting reactant is consumed in the reaction, the operational yield __________ the relative yield. (A) Is greater than (B) Is smaller than (C) Equals (D) Can be either greater or smaller than (depends on the type of reaction)

Last Answer : (C) Equals

In case of grinding in a ball mill (A) Wet grinding achieves a finer product size than dry grinding (B) Its capacity decreases with increasing fineness of the products (C) Grinding cost and power requirement increases with increasing fineness of the products (D) All (A), (B) and (C)

Description : In case of grinding in a ball mill (A) Wet grinding achieves a finer product size than dry grinding (B) Its capacity decreases with increasing fineness of the products (C) Grinding cost and power requirement increases with increasing fineness of the products (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

Tube mill compared to ball mill (A) Produces finer products (B) Is long in comparison with its diameter (C) Uses smaller balls (D) All (A), (B) & (C)

Description : Tube mill compared to ball mill (A) Produces finer products (B) Is long in comparison with its diameter (C) Uses smaller balls (D) All (A), (B) & (C)

Last Answer : (D) All (A), (B) & (C)

To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Description : To get a fine talc powder from its granules, the equipment used is (A) Roller crusher (B) Ball mill (C) Jaw crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Which of the following gives the work required for size reduction of coal to -200 mesh in a ball mill most accurately? (A) Rittinger's law (B) Kick's law (C) Bond's law (D) None of these

Description : Which of the following gives the work required for size reduction of coal to -200 mesh in a ball mill most accurately? (A) Rittinger's law (B) Kick's law (C) Bond's law (D) None of these

Last Answer : (A) Rittinger's law

Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Description : Run of mine (ROM) coal is crushed by a __________ for use in domestic ovens. (A) Jaw crusher (B) Hammer crusher (C) Ball mill (D) Tube mil

Last Answer : (B) Hammer crusher

A pebble mill (A) Is a ball mill (B) Employs flints or ceramic pebbles as the grinding medium (C) Is a tube mill lined with ceramic or other non-metallic liner (D) Both (B) and (C)

Description : A pebble mill (A) Is a ball mill (B) Employs flints or ceramic pebbles as the grinding medium (C) Is a tube mill lined with ceramic or other non-metallic liner (D) Both (B) and (C)

Last Answer : (D) Both (B) and (C)

For achieving maximum capacity of the ball mill, the ball charge should be equal to about __________ percent of the ball mill volume. (A) 10 (B) 25 (C) 50 (D) 75

Description : For achieving maximum capacity of the ball mill, the ball charge should be equal to about __________ percent of the ball mill volume. (A) 10 (B) 25 (C) 50 (D) 75

Last Answer : (C) 50

For the preliminary breaking of hard rock, we use a (A) Gyratory crusher(B) Ball mill(C) Tube mill(D) Squirrel-cage disintegrator

Description : For the preliminary breaking of hard rock, we use a (A) Gyratory crusher (B) Ball mill (C) Tube mill (D) Squirrel-cage disintegrator

Last Answer : (A) Gyratory crusher

A tube mill as compared to a ball mill (A) Employs smaller balls (B) Gives finer size reduction but consumes more power (C) Has larger length/diameter ratio (>2 as compared to 1 for ball mill) (D) All (A), (B) and (C)

Description : A tube mill as compared to a ball mill (A) Employs smaller balls (B) Gives finer size reduction but consumes more power (C) Has larger length/diameter ratio (>2 as compared to 1 for ball mill) (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a(A) Buhrstone mill(B) Ball mill(C) Crushing rolls(D) Hammer mill

Description : For grinding of cereals, grains, spices, pigments, saw dust, cork etc., the most extensively used size reduction equipment is a (A) Buhrstone mill (B) Ball mill (C) Crushing rolls (D) Hammer mill

Last Answer : (A) Buhrstone mill

Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Description : Out of the following size reduction equipments, the maximum feed size can be accepted by the (A) Tube mill (B) Ball mill (C) Jaw crusher (D) Jet pulveriser

Last Answer : (C) Jaw crusher

In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Description : In ball mill operation, the feed size (Df in meters) and the ball diameter (Db in metres) are related as (where, K = grindability constant (varying from 0.9 to 1.4 in increasing order of hardness)) (A) Db 2 = K.Df (B) Db = K.Df (C) Db 3 = K.Df (D) Db 2 = K.Df

Last Answer : (A) Db 2 = K.Df

__________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Description : __________ balls capable of grinding the feed in a ball mill gives the maximum efficiency. (A) Cast iron (B) Minimum size (C) Maximum size (D) Elliptical

Last Answer : (B) Minimum size

. To produce talcum powder, use (A) Ball mill (B) Hammer mill (C) Jet mill (D) Pin mill

Description : . To produce talcum powder, use (A) Ball mill (B) Hammer mill (C) Jet mill (D) Pin mill

Last Answer : (A) Ball mill

Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Description : Limestone is normally crushed in a (A) Roll crusher (B) Hammer crusher (C) Ball mill (D) Tube mill

Last Answer : (B) Hammer crusher

Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher(B) Ball mill(C) Roll crusher(D) Gyratory crusher

Description : Coal is finally pulverised to 200 mesh size for burning in boilers by a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Ball mill is used for (A) Crushing (B) Coarse grinding (C) Fine grinding (D) Attrition

Description : Ball mill is used for (A) Crushing (B) Coarse grinding (C) Fine grinding (D) Attrition

Last Answer : (C) Fine grinding

A __________ mixer resembles a ball mill without balls. (A) Banbury (B) Pug mill (C) Tumbling (D) Pan

Description : A __________ mixer resembles a ball mill without balls. (A) Banbury (B) Pug mill (C) Tumbling (D) Pan

Last Answer : (C) Tumbling

Close circuit grinding by a ball mill with air sweeping employs a (A) Classifier (B) Cyclone separator between mill & classifier (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Close circuit grinding by a ball mill with air sweeping employs a (A) Classifier (B) Cyclone separator between mill & classifier (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Maximum size reduction in a ball mill is done by the, __________ action. (A) Attrition (B) Compression (C) Impact (D) Cutting

Description : Maximum size reduction in a ball mill is done by the, __________ action. (A) Attrition (B) Compression (C) Impact (D) Cutting

Last Answer : (C) Impact

A tube mill compared to a ball mill (A) Has a higher length/diameter ratio(B) Produces a coarser product(C) Has a higher diameter/length ratio(D) Uses much larger balls

Description : A tube mill compared to a ball mill (A) Has a higher length/diameter ratio (B) Produces a coarser product (C) Has a higher diameter/length ratio (D) Uses much larger balls

Last Answer : (A) Has a higher length/diameter ratio

In a ball mill, the volume occupied by the balls (when the mill is stopped) is about __________ percent of the volume of the mill. (A) 35 (B) 50 (C) 70 (D) 85

Description : In a ball mill, the volume occupied by the balls (when the mill is stopped) is about __________ percent of the volume of the mill. (A) 35 (B) 50 (C) 70 (D) 85

Last Answer : (B) 50

Length/diameter ratio of a ball mill is (A) 1.5 (B) 1 (C) < 1 (D) > 1

Description : Length/diameter ratio of a ball mill is (A) 1.5 (B) 1 (C) < 1 (D) > 1

Last Answer : (C) < 1

Grinding efficiency of a ball mill is of the order of __________ percent. (A) 1-5 (B) 40-50 (C) 75-80 (D) 90-95

Description : Grinding efficiency of a ball mill is of the order of __________ percent. (A) 1-5 (B) 40-50 (C) 75-80 (D) 90-95

Last Answer : (A) 1-5

Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Description : Cement clinker is reduced to fine size by a (A) Roll crusher (B) Ball mill (C) Tube mill (D) Hammer mill

Last Answer : (C) Tube mill

Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Description : Carbon black is pulverised in a (A) Hammer crusher (B) Ball mill (C) Roll crusher (D) Gyratory crusher

Last Answer : (B) Ball mill

Balls in a ball mill are usually made of (A) Steel (B) Cast iron (C) Stainless steel (D) Bronze

Description : Balls in a ball mill are usually made of (A) Steel (B) Cast iron (C) Stainless steel (D) Bronze

Last Answer : (A) Steel

Energy consumed for crushing one ton of material ranges from __________ kWh. (A) 0.01 to 0.1 (B) 0.5 to 1.5 (C) 2 to 3.5 (D) 4 to 5

Description : Energy consumed for crushing one ton of material ranges from __________ kWh. (A) 0.01 to 0.1 (B) 0.5 to 1.5 (C) 2 to 3.5 (D) 4 to 5

Last Answer : (B) 0.5 to 1.5

Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not exceed 4 (C) Both the rolls run necessarily at the same speed (D) Reduction ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Description : Pick out the wrong statement pertaining to the roll crushers. (A) Maximum feed size determines the required roll diameter (B) For hard material's crushing, the reduction ratio should not ... ratio and differential roll speed affect production rate & energy consumed per unit of surface produced

Last Answer : (C) Both the rolls run necessarily at the same speed

What is the absolute time a pilot should stop drinking before flying? a. 6 hours but it depends upon the amount of alcohol that has been consumed b. 24 hours but it depends upon the amount of alcoho l that has been consumed c. 12 hours but it depends upon the amount of alcohol that has been consumed d. 8 hours but it depends upon the amount of alcohol that has been consumed

Description : What is the absolute time a pilot should stop drinking before flying? a. 6 hours but it depends upon the amount of alcohol that has been consumed b. 24 hours but it depends upon the amount of ... that has been consumed d. 8 hours but it depends upon the amount of alcohol that has been consumed

Last Answer : d. 8 hours but it depends upon the amount of alcohol that has been consumed