Description : Correct viscosity of furnace oil at the burner tip for proper atomisation is about 25 centistokes. To reduce the viscosity of high viscosity furnace oil (250 centistokes) to the correct atomisation viscosity (i.e. 25 cst), it should be preheated to about ___________°C. (A) 70 (B) 85 (C) 105 (D) 145
Last Answer : (C) 105
Description : Which of the following does not require preheating during storage in the storage tank as well as during atomisation through burners? (A) PCM (B) Tar (C) Light diesel oil (D) Low viscosity furnace oil
Last Answer : (C) Light diesel oil
Description : Maximum viscosity of tar/PCM/fuel oil for easy and efficient atomisation in conventional burner is __________ centistokes (or 100 Redwood I seconds). (A) 5 (B) 25 (C) 50 (D) 100
Last Answer : (B) 25
Description : Optimum preheating temperature for pitch creosote mixture (PCM) which is also termed as C.T.F-200, before atomisation through burners is (A) 200 °F (B) 200 °C (C) 200 °K (D) 200 °R
Last Answer : (A) 200 °F
Description : Which of the following varies as the square root of oil pressure during atomisation of fuel oil through a pressure jet burner? (A) Output & fineness (B) Velocity (C) Both (A) & (B) (D) None of these
Last Answer : Option C
Description : Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150
Last Answer : (C) 150
Description : Ceramic recuperators (made of SiC) is economical, only when used for preheating combustion air above __________ °C. (A) 250 (B) 650 (C) 850 (D) 1000
Last Answer : (B) 650
Description : Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface ... C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50
Last Answer : (C) 70
Description : Mercury electrolytic cell produces 50-70% NaOH solution. Its operating temperature is __________ °C. (A) 25 (B) 60-70 (C) 150-200 (D) 250-300
Last Answer : (B) 60-70
Description : In case of pulverised coal fired steam boiler, the secondary air serves the main purpose of (A) Transportation of coal (B) Drying of coal (C) Combustion of coal by supplying it around the burner (D) Preheating the primary air
Last Answer : (C) Combustion of coal by supplying it around the burner
Description : Pitch (a product of coal tar distillation) is always mixed with creosote oil, when it is to be burnt in a burner, because (A) Its calorific value is very less (B) Tar neutralises the residual acids ... for its transportation through pipelines at economic pressure drop (D) All (A), (B) and (C)
Last Answer : (C) It reduces viscosity and imparts fluidity for its transportation through pipelines at economic pressure drop
Description : Noise level heard at a distance of about 100 metres from a jet engine with after burner is about __________ decibels. (A) 120 (B) 140 (C) 170 (D) 200
Last Answer : (C) 170
Description : Higher furnace temperature cannot be achieved by use of a lean fuel gas in the furnace by (A) Increasing the draft in the furnace (B) Preheating the fuel gas (C) Oxygen enrichment of combustion air (D) Preheating the combustion air
Last Answer : (A) Increasing the draft in the furnace
Description : Temperature of a furnace fired with low calorific value fuel gas (i.e. lean gas) can be increased by (A) Preheating the combustion air (B) Oxygen enrichment of combustion air (C) Preheating the fuel gas (D) All (A), (B) & (C)
Last Answer : (D) All (A), (B) & (C)
Description : In case of liquid petrofuels, momentary combustion is observed at its (A) Flash point (B) Preheating temperature corresponding to viscosity of 25 centistokes (C) Flame temperature (D) Fire point
Last Answer : (A) Flash point
Description : Temperature of preheated air used for the transportation of pulverised coal through pipes to the burner of a boiler furnace is restricted to a maximum limit of about 300° C to avoid the (A) ... chamber (B) Risk of explosion (C) Chances of clinker formation (D) Incomplete combustion of coal
Last Answer : (B) Risk of explosion
Description : Fuel economy in furnaces can be achieved by (A) Using oxygen enriched combustion air (B) Preheating the combustion air (C) Reducing the heat loss through furnace openings & doors (D) All (A), (B) and (C
Last Answer : (D) All (A), (B) and (C
Description : While the fuel fired furnace can be used upto a maximum temperature of about 1700°C, the electric furnace can be used upto a temperature of about __________ °C. (A) 2000 (B) 3000 (C) 4500 (D) 6000
Last Answer : (C) 4500
Description : The temperature in the calcium carbide furnace is __________ °C. (A) 200-300 (B) 700-850 (C) 2000-2200 (D) 4000-4500
Last Answer : (C) 2000-2200
Description : Exothermic condensation reaction of monochlorobenzene with chloral in presence of 20% oleum as catalyst produces DDT. The reaction temperature is maintained at __________ °C. (A) 15-30 (B) 90-100 (C) 250-300 (D) < 0
Last Answer : (A) 15-30
Description : Turndown ratio of a burner gives an idea of the __________ in the furnace. (A) Range of fuel firing rates (B) Volume of the combustion chamber (C) Maximum heat input rate only (D) Minimum heat input rate only
Last Answer : (A) Range of fuel firing rates
Description : To devitalize weed seeds in manure, the composting temperature must be in which of the following range a). 35-50 °C b). 50-65 °C c). 65-90 °C d). 90-105 °C
Last Answer : c). 65-90 °C
Description : The amount of combustible escaping unconsumed from the furnace, depends upon the (A) Air supplied and furnace temperature (B) Burner design (thoroughness of mixing versus stratification) (C) Air preheat and the flow of ... , by acceleration or by change of direction) (D) All (A), (B) and (C)
Last Answer : (D) All (A), (B) and (C)
Description : Overall thermal efficiency of a lumpy coal fired suitably designed heating furnace, if operated & maintained properly may be about __________ percent. (A) 10-15 (B) 25-30 (C) 45-50 (D) 65-70
Last Answer : (B) 25-30
Description : Which furnace employs preheating, heating and soaking zones? (A) Soaking pit (B) Reheating furnace (C) Open hearth furnace (D) Cupola
Last Answer : (B) Reheating furnace
Description : Nitriding of steel is done (in electric furnace) at __________ °C. (A) 510 (B) 1720 (C) 2210 (D) 910
Last Answer : (A) 510
Description : Fusion zone in the electric furnace used for reduction of phosphate rock to elemental phosphorous is maintained at __________ °C. (A) 250-300 (B) 500-750 (C) 950-1050 (D) 1400-1450
Last Answer : (D) 1400-1450
Description : The pressure (kg/cm2 ) and temperature (°C) maintained in electrical desalters for crude oil are respectively (A) 10 and 120 (B) 1 and 200 (C) 50 and 250 (D) 10 and 300
Last Answer : (B) 1 and 200
Description : Hot water (0.01 m3 /min) enters the tube side of a counter current shell and tube heat exchanger at 80°C and leaves at 50°C. Cold oil (0.05 m3 /min) of density 800 kg/m3 and specific heat of ... mean temperature difference in °C is approximately (A) 32 (B) 37 (C) 45 (D) 50
Last Answer : (A) 32
Description : The thermal efficiency of an air/fuel gas preheating recuperator may be as high as __________ percent. (A) 50 (B) 65 (C) 85 (D) 99
Last Answer : (C) 85
Description : Medium viscosity lubricating oil can be most ideally pumped by a __________ pump. (A) Vane (B) Piston (C) Centrifugal (D) Plunger
Last Answer : (A) Vane
Description : The conversion of caprolactam in the above case is about __________ percent. (A) 25 (B) 50 (C) 70 (D) 90
Last Answer : (D) 90
Description : P2O5 content in triple superphosphate is about __________ percent. (A) 42-50 (B) 15-20 (C) 85-90 (D) 70-75
Last Answer : (A) 42-50
Description : The amount of benzene present in pure Benzol is about __________ percent. (A) 30 (B) 50 (C) 70 (D) 90
Description : Steam condenser tubes are made of admiralty brass, in which percentage of zinc & copper are __________ respectively. (A) 70 & 30 (B) 30 & 70 (C) 50 & 50 (D) 90 & 10
Last Answer : (A) 70 & 30
Description : . The inner wall of a furnace is at a temperature of 700°C. The composite wall is made of two substances, 10 and 20 cm thick with thermal conductivities of 0.05 and 0.1 W.m-1.°C-1 respectively. The ambient air is at 30°C ... from the outer surface in W.m-2 is (A) 165.4 (B) 167.5 (C) 172.5 (D) 175
Last Answer : (A) 165.4
Description : Aniline point of high speed diesel may be about __________ °C. (A) 35 (B) 70 (C) 105 (D) 150
Last Answer : (B) 70
Description : Normal fasting blood sugar level per 100 ml. of blood in man is - (1) 30 - 50 mg (2) 50 - 70 mg (3) 80 -100 mg (4) 120 -140 mg
Last Answer : (3) 80 -100 mg Explanation: The blood sugar concentration or blood glucose level is the amount of glucose (sugar) present in the blood of a human or animal. Glucose levels are usually lowest in the ... (termed the fasting level"), and rise after meals for an hour or two by a few millimolar.
Description : For batching 1:3:6 concrete mix by volume, the ingredients required per bag of 50 kg cement, are: (A) 70 litres of sand and 120 litres of aggregates (B) 70 kg of sand and 140 litres of ... C) 105 litres of sand and 140 litres of aggregates (D) 105 litres of sand and 210 litres of aggregates
Last Answer : Answer: Option D
Description : Normal fasting blood sugar level per 100 ml. of blood in man is (1) 30 - 50 mg (2) 50 - 70 mg (3) 80 -100 mg (4) 120 -140 mg
Last Answer : 80 -100 mg
Description : Light oil whose major component is Benzol, is obtained by the distillation of crude tar in the temperature range of __________ °C. (A) 80-170 (B) 200-300 (C) 250-270
Last Answer : (A) 80-170
Description : Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280
Last Answer : (D) 250-280
Description : Very dilute solutions are generally used in fermentation reactions for which the optimum temperature range is __________ °C. (A) -5 to 0 (B) 5 to 10 (C) 30 to 50 (D) 75 to 80
Last Answer : (C) 30 to 50
Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200
Last Answer : (B) 100
Description : Recrystallisation temperature of steel is __________ °C. (A) 50 (B) 300 (C) 500 (D) 800
Last Answer : (D) 800
Description : Q.61. CA Co manufactures a single product and has drawn up the following flexed budget for the year. 60% 70% 80% Rs Rs Rs Direct materials 120,000 140,000 160,000 Direct labour 90,000 105,000 120,000 Production ... activity? (a) Rs 330,300 (b) Rs 370,300 (c) Rs 373,300 (d) Rs 377,300
Last Answer : (b) Rs 370,300
Description : LSHS is a type of furnace oil, which (A) Is more viscous than high viscosity furnace oil (HVFO) (B) Stands for low sulphur heavy stock (C) Is an ideal fuel for metallurgical furnaces due to its lower sulphur content (< 1%) (D) All (A), (B) and (C)
Description : Which of the following is not an important property of fuel oil/furnace oil? (A) Sulphur content (B) Viscosity (C) Aniline point (D) Flash point
Last Answer : (C) Aniline point
Description : Preheating of __________ the flame temperature. (A) The gaseous fuel before combustion decreases (B) Combustion air decreases (C) Either the fuel or the air or both, increases (D) Either the fuel or the air does not affect
Last Answer : (C) Either the fuel or the air or both, increases