Description : Diesel index is defined as (A) (°API) × (Aniline Point, °F)/100 (B) (°API) × (Aniline Point, °C)/100 (C) (°API) × (100)/Aniline Point, °F (D) (°API) × (100)/Aniline Point, °C
Last Answer : (A) (°API) × (Aniline Point, °F)/100
Description : Mercury electrolytic cell produces 50-70% NaOH solution. Its operating temperature is __________ °C. (A) 25 (B) 60-70 (C) 150-200 (D) 250-300
Last Answer : (B) 60-70
Description : Flash point of motor gasoline may be around __________ °C. (A) 10 (B) 45 (C) 100 (D) 150
Last Answer : (B) 45
Description : To devitalize weed seeds in manure, the composting temperature must be in which of the following range a). 35-50 °C b). 50-65 °C c). 65-90 °C d). 90-105 °C
Last Answer : c). 65-90 °C
Description : Aniline point of the diesel is a measure of its __________ content. (A) Aromatic (B) Paraffin (C) Olefin (D) Naphthene
Last Answer : (B) Paraffin
Description : Equal volumes of aniline and diesel oil when mixed at room temperature (during summer) was found to be completely miscible. It means that the aniline point of the diesel is __________ the room temperature. (A) ... (B) Less than (C) Same as (D) Either more or less; depends on the room temperature
Last Answer : (C) Same as
Description : High aniline point of diesel indicates that, it (A) Is highly aromatic (B) Has a large ignition delay (C) Is highly paraffinic (D) Has a low diesel index
Last Answer : (C) Is highly paraffinic
Description : High aniline point of a petrofuel (say diesel) indicates that (A) It is highly aromatic in nature (B) It is highly paraffinic in nature (C) It has a very low diesel index (D) Its ignition quality is very poor
Last Answer : (B) It is highly paraffinic in nature
Description : Aniline point is the (A) Characteristic property of diesel & lubricating oils (B) Measure of aromatic content of oil (C) Both (A) and (B) (D) Neither (A) nor (B)
Last Answer : (C) Both (A) and (B
Description : Diesel index (an alternative index for expressing the quality of diesel) is (A) Determined by using a test engine (B) Not related to aniline point (C) Equal to cetane number plus 3 (D) All (A), (B) & (C)
Last Answer : (C) Equal to cetane number plus 3
Description : Aniline point is a property of the (A) Diesel (B) LPG (C) Naphtha (D) Gasoline
Last Answer : (C) Naphtha
Description : Aniline point is the temperature at which (A) Equal weight of diesel & the aniline are completely miscible (B) Equal weight of aniline & the test sample are completely miscible (C) Equal volume of aniline & the test sample are completely miscible (D) Aniline vaporises
Last Answer : (C) Equal volume of aniline & the test sample are completely miscible
Description : Condensation polymerisation of caprolactam is carried out in the reactor maintained at a temperature of __________ °C for producing nylon- 6. (A) -20 to 25 (B) 50 to 75 (C) 100 to 150 (D) 250-280
Last Answer : (D) 250-280
Description : Most of the plastics are safe to be used upto a maximum temperature of __________ °C. (A) 100 (B) 150 (C) 350 (D) 450
Last Answer : (B) 150
Description : Molecular sieves are regenerated by heating to __________ °C. (A) < 150 (B) 200-330 (C) > 500 (D) > 1000
Last Answer : (B) 200-330
Description : Flue gas outlet temperature from the chimney of any furnace should be ideally about __________ °C. (A) 50 (B) 100 (C) 150
Last Answer : (C) 150
Description : The temperature at which plastic layer formation takes place during carbonisation of coal varies from __________ °C. (A) 100 to 150 (B) 350 to 450 (C) 550 to 650 (D) 700 to 850
Last Answer : (B) 350 to 450
Description : Fermentation of molasses to produce ethyl alcohol is done at __________ °C. (A) 20 - 30 (B) < - 5 (C) 100 - 150 (D) 250 - 300
Last Answer : (A) 20 - 30
Description : A thin, flat & square plate measuring 2 m 2 m is freely hanging in ambient air at 25°C. It is exposed to the solar radiation falling on one side of the plate at the rate of 500 W/m2. The plate temperature will ... heat transfer co-efficient is __________ W/m2 °C. (A) 50 (B) 100 (C) 150 (D) 200
Last Answer : (B) 100
Description : Temperature attained in soldering of metals is about __________ °C. (A) 150-300 (B) 400-500 (C) 650-800 (D) 1000-1100
Last Answer : (A) 150-300
Description : Preheating temperature of medium viscosity furnace oil for better atomisation through burner is about __________ °C. (A) 50 (B) 70 (C) 90 (D) 140
Last Answer : (C) 90
Description : Three materials A, B and C of equal thickness and of thermal conductivity of 20, 40 & 60 kcal/hr. m. °C respectively are joined together. The temperature outside of A and C are 30°C and 100°C respectively. The interface ... C will be at a temperature of __________ °C. (A) 40 (B) 95 (C) 70 (D) 50
Last Answer : (C) 70
Description : Maximum permissible limit of industrial noise as recommended by World Health Organisation (WHO) is __________ decibels. (A) 35 (B) 75 (C) 95 (D) 105
Last Answer : (B) 75
Description : A typical yield of diesel in straight run distillation of crude oil may be about __________ percent. (A) 8 (B) 18 (C) 28 (D) 35
Last Answer : (A) 8
Description : X, Y & Z rent a pasture. X puts 20 cows for 5 months , Y puts 24 cows for 7 months and Z puts 30 cows for 3 months for grazing. If the rent of the pasture is Rs. 150, how much must z pay as his share of rent? A) 32 B) 39.65 C) 37.70 D) 35.20
Last Answer : Answer: C) X : Y : Z = 20* 5 : 24* 7 : 30 * 3 = 100 : 168 : 90 =50 : 84 : 45 Therefore Z’s rent = Rs (150 * 45 / 179) = Rs.(6750/179) Rs.37.70
Description : How much tomato average production (q.) may be yield from one hectare ? (A) 100 (B) 105-150 (C) 250 (D) 160-275
Last Answer : (D) 160-275
Description : Correct viscosity of furnace oil at the burner tip for proper atomisation is about 25 centistokes. To reduce the viscosity of high viscosity furnace oil (250 centistokes) to the correct atomisation viscosity (i.e. 25 cst), it should be preheated to about ___________°C. (A) 70 (B) 85 (C) 105 (D) 145
Last Answer : (C) 105
Description : Typical solvent polymerisation reaction conditions for the production of high density polythene by Zeigler process is (A) 7 kgf/cm2 and 70 °C (B) 1000 kgf/cm2 and 100°C (C) 7 kgf/cm2 and 700°C (D) 1 kgf/cm2 (gage) and 70°C
Last Answer : (A) 7 kgf/cm2 and 70 °C
Description : Acid dew point temperature (ADT) of a flue gas produced by the combustion of a fuel containing 1% sulphur may be about __________ °C. (A) 80 (B) 130 (C) 180 (D) 250
Last Answer : (B) 130
Description : High speed steel tools retain their hardness upto a temperature of __________ °C. (A) 500 (B) 750 (C) 900 (D) 1100
Last Answer : (C) 900
Last Answer : Option C
Description : Softening point of high density polythene is about __________ °C. (A) 85 (B) 135 (C) 165 (D) 205
Last Answer : (B) 135
Description : Aniline point test of an oil qualitatively indicates the __________ content of an oil. (A) Paraffin (B) Olefin (C) Aromatic (D) Naphthene
Last Answer : (C) Aromatic
Description : Dust content in raw blast furnace gas is about __________ gm/Nm3 ; hence it is cleaned to the dust level of about < 10 mg /Nm3 before use. (A) 15-30 (B) 1-2 (C) 70-100 (D) 150-200
Last Answer : (A) 15-30
Description : Cetane number of diesel used in trucks may be about (A) 50 (B) 14 (C) 35 (D) 85
Last Answer : (A) 50
Description : Salt content (measured as sodium chloride) in electrically desalted crude oil comes down to a level of about __________ ptb (pounds per thousand barrel). (A) 0.03 (B) 3 (C) 35 (D) 70
Last Answer : (B) 3
Description : In a ball mill, the volume occupied by the balls (when the mill is stopped) is about __________ percent of the volume of the mill. (A) 35 (B) 50 (C) 70 (D) 85
Last Answer : (B) 50
Description : P2O5 content in superphosphate is about __________ percent. (A) 30-35 (B) 15-20 (C) 65-70 (D) 85-90
Last Answer : (B) 15-20
Description : Average sulphur content in Indian pyrites is about __________ percent. (A) 15 (B) 35 (C) 55 (D) 70
Last Answer : (B) 35
Description : Equipment installation cost in a chemical process plant ranges from __________ percent of the purchased equipment cost. (A) 10 to 20 (B) 35 to 45 (C) 55 to 65 (D) 70 to 80
Last Answer : (B) 35 to 45
Description : A solid aluminium ball, when quenched in a water bath maintained at 40°C, cools down from 550°C to 450°C in 20 seconds. The expected temperature of the ball after next 20 seconds may be about __________ °C. (A) 370 (B) 340 (C) 320 (D) 300
Last Answer : (A) 370
Description : Rs.4900 was divided among a group of 150 children. If each girl gets Rs.50 and each boy gets Rs.25 then, the number of boys in the group is: (a) 100 (b) 102 (c) 104 (d) 105
Last Answer : (c) 104
Description : Dimensions of Postcards is a) Max 100 X 150 mm & min 80 X 140 mm b) Max 105 X 149 mm & min 90 X 140 mm c) Max 150 X 200 mm & min 70X 140 mm d) None of these
Last Answer : b) Max 105 X 149 mm & min 90 X 140 mm
Description : Find the electric field when the velocity of the field is 12m/s and the flux density is 8.75 units. a) 510 b) 105 c) 150 d) 165
Last Answer : b) 105
Description : Determine the maximum shearing stress and elongation in a helical steel spring composed of 20 turns of 20-mm-diameter wire on a mean radius of 90 mm when the spring is supporting a load of 1.5 kN. and G = 83 GPa. a. 200 mm b. 105.4 mm c. 150 mm d. 250 mm
Last Answer : b. 105.4 mm
Description : A thick cylinder is subjected to an internal pressure of 60 MPa. If the hoop stress on the outer surface is 150 MPa, then the hoop stress on the internal surface is a) 105 MPa b) 180 MPa c) 210 MPa d) 135 MPa.
Last Answer : c) 210 MPa
Description : The normal values for creatinine clearance varies from (A) 20–40 ml/min (B) 40–60 ml/min (C) 70–85 ml/min (D) 95–105 ml/min
Last Answer : Answer : D
Description : After accounting for SDA, the net gain of energy from 25 gm of carbohydrates is about (A) 70 kcal (B) 95 kcal (C) 100 kcal (D) 105 kcal
Last Answer : Answer : B
Description : In India, which one of the following should be considered the right combination of the age in days and live body weight in kg for a lamb for its weaning ? (A) 20 days to 30 days and 6 kg to 7 kg (B) 45 days to 60 ... (D) 75 days to 90 days and 12 kg to 15 kg (E) 55 days to 70 days and 9 kg to 11 kg
Last Answer : (C) 105 days to 120 days and 18 kg to 21 kg
Description : For batching 1:3:6 concrete mix by volume, the ingredients required per bag of 50 kg cement, are: (A) 70 litres of sand and 120 litres of aggregates (B) 70 kg of sand and 140 litres of ... C) 105 litres of sand and 140 litres of aggregates (D) 105 litres of sand and 210 litres of aggregates
Last Answer : Answer: Option D