Amino resins are used in paper treatment to improve its (A) Wet tear and bursting strength (B) Folding endurance (C) Wet rub resistance(D) All (A), (B) & (C)

Amino resins are used in paper treatment to improve its
(A) Wet tear and bursting strength
(B) Folding endurance
(C) Wet rub resistance
(D) All (A), (B) & (C)
by

1 Answer

Answer :

(D) All (A), (B) & (C)
by

Related questions

Cation exchange resins used in water treatment is made from __________ resin. (A) Urea formaldehyde (B) Epoxy (C) Amino (D) Phenolic

Description : Cation exchange resins used in water treatment is made from __________ resin. (A) Urea formaldehyde (B) Epoxy (C) Amino (D) Phenolic

Last Answer : (A) Urea formaldehyde

Presence of high concentration of ozone and smog in atmospheric air causes the(A) Embrittlement & decrease of folding resistance of paper(B) Cracking of rubber products(C) Fading of dye on textiles(D) Damage of electrical insulator on high tension power line

Description : Presence of high concentration of ozone and smog in atmospheric air causes the (A) Embrittlement & decrease of folding resistance of paper (B) Cracking of rubber products (C) Fading of dye on textiles (D) Damage of electrical insulator on high tension power line

Last Answer : (B) Cracking of rubber products

Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Description : Failure of a material is termed as fatigue failure, if it fails below the yield point. The resistance to fatigue failure of a material is measured by the (A) Ultimate tensile strength (U.T.S.) (B) Endurance limit (C) Elastic limit (D) None of these

Last Answer : (B) Endurance limit

Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Description : Notched bar test is used for testing the __________ of a material. (A) Impact strength (B) Endurance limit (C) Machinability (D) Corrosion resistance

Last Answer : (A) Impact strength

Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Description : Fatigue resistance of a material is measured by the (A) Elastic limit (B) Ultimate tensile strength (C) Young's modulus (D) Endurance limit

Last Answer : (D) Endurance limit

Give reason: It is easy to tear wet paper than dry paper.

Description : Give reason: It is easy to tear wet paper than dry paper.

Last Answer : The tensile strength of paper decreases when paper becomes wet.

The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Description : The resistance to fatigue of a material is measured by (a) elastic limit (b) Young's modulus (c) ultimate tensile strength (d) endurance limit

Last Answer : (d) endurance limit

A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Description : A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Last Answer : B) Completely reversed

A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Description : A material being tested for endurance strength is subjected to the __________ load. (A) Impact (B) Completely reversed (C) Dynamic (D) Static & dynamic

Last Answer : (B) Completely reversed

Silicone resins, which are highly water repellent and has good heat resistance cannot be used (A) As room temperature adhesive (B) As grease & lubricant

Description : Silicone resins, which are highly water repellent and has good heat resistance cannot be used (A) As room temperature adhesive (B) As grease & lubricant

Last Answer : (A) As room temperature adhesive

__________ are produced by reacting polybasic acid (e.g. Phthalic anhydride) with polyhydric alcohol (e.g., glycerol). (A) Unsaturated polyester (B) Alkyd resins (C) Saturated polyester (D) Amino resins

Description : __________ are produced by reacting polybasic acid (e.g. Phthalic anhydride) with polyhydric alcohol (e.g., glycerol). (A) Unsaturated polyester (B) Alkyd resins (C) Saturated polyester (D) Amino resins

Last Answer : (B) Alkyd resins

__________ resins are produced by the condensation polymerisation of formaldehyde with urea or melamine. (A) Epoxy (B) Amino (C) Alkyd (D) Phenolic

Description : __________ resins are produced by the condensation polymerisation of formaldehyde with urea or melamine. (A) Epoxy (B) Amino (C) Alkyd (D) Phenolic

Last Answer : (B) Amino

Plasticisers are added to synthetic plastics to (A) Impart flexibility (B) Improve workability during fabrication (C) Develop new improved properties not present in the original resins (D) All (A), (B) and (C)

Description : Plasticisers are added to synthetic plastics to (A) Impart flexibility (B) Improve workability during fabrication (C) Develop new improved properties not present in the original resins (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

High strength concrete is used in pre-stressed member (A) To overcome high bearing stresses developed at the ends (B) To overcome bursting stresses at the ends (C) To provide high bond stresses (D) All the above

Description : High strength concrete is used in pre-stressed member (A) To overcome high bearing stresses developed at the ends (B) To overcome bursting stresses at the ends (C) To provide high bond stresses (D) All the above

Last Answer : Answer: Option D

Which of the following is not a dielectric material? (A) Cotton, silk and paper (B) Asbestos, glass, porcelain and mica (C) Rubber and polymeric resins (D) All refractory materials

Description : Which of the following is not a dielectric material? (A) Cotton, silk and paper (B) Asbestos, glass, porcelain and mica (C) Rubber and polymeric resins (D) All refractory materials

Last Answer : Option C

Plasticisers are added to polymers to improve their (A) Tensile strength (B) Softness & flexibility (C) Acid resistance (D) Alkali resistance

Description : Plasticisers are added to polymers to improve their (A) Tensile strength (B) Softness & flexibility (C) Acid resistance (D) Alkali resistance

Last Answer : (B) Softness & flexibility

Cation exchange resins (0.3 to 1 mm size) used in water treatment is prepared from __________ resins. (A) Epoxy (B) Phenol formaldehyde (C) Urea formaldehyde (D) Melamine formaldehyde

Description : Cation exchange resins (0.3 to 1 mm size) used in water treatment is prepared from __________ resins. (A) Epoxy (B) Phenol formaldehyde (C) Urea formaldehyde (D) Melamine formaldehyde

Last Answer : (C) Urea formaldehyde

Pick out the wrong statement. (A) Recycled coarse material to the grinder by a classifier is termed as circulating load (B) Wear and tear in wet crushing is more than that in dry crushing of materials (C) Size enlargement (opposite of size reduction) is not a mechanical operation (D) A 'dust catcher' is simply an enlargement in a pipeline which permits the solids to settle down due to reduction in velocity of the dust laden gas

Description : Pick out the wrong statement. (A) Recycled coarse material to the grinder by a classifier is termed as circulating load (B) Wear and tear in wet crushing is more than that in dry crushing of ... a pipeline which permits the solids to settle down due to reduction in velocity of the dust laden gas

Last Answer : (C) Size enlargement (opposite of size reduction) is not a mechanical operation

Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Description : Wohler test is a destructive test to find out the __________ strength of a prepared metal specimen. (A) Creep (B) Fatigue (C) Endurance (D) Tensile

Last Answer : (B) Fatigue

The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

Description : The maximum stress below which a material can withstand an infinite number of cycle of stress, is termed as the (A) Fatigue strength (B) Creep strength (C) Resilience (D) Endurance limit

Last Answer : D) Endurance limit

The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Description : The highest stress that a material can withstand for a specified length of time without excessive deformation is called the __________ strength. (A) Creep (B) Endurance (C) Fatigue (D) None of these

Last Answer : Option A

Yield strength of a material is determined by the __________ test. (A) Creep (B) Tension (C) Compression (D) Endurance

Description : Yield strength of a material is determined by the __________ test. (A) Creep (B) Tension (C) Compression (D) Endurance

Last Answer : Option B

.In regard to the glass of quartz particles of filling restorative resin; the microfill resins tend to have, A. A higher coefficient of thermal expansion and a higher crashing strength B. A higher coefficient of thermal expansion and a lower crashing strength C. A lower coefficient of thermal expansion and a higher crashing strength D. A lower coefficient of thermal expansion and a lower crashing strength

Description : .In regard to the glass of quartz particles of filling restorative resin; the microfill resins tend to have, A. A higher coefficient of thermal expansion and a higher crashing strength B. ... and a higher crashing strength D. A lower coefficient of thermal expansion and a lower crashing strength

Last Answer : B. A higher coefficient of thermal expansion and a lower crashing strength

Pick up the correct statement from the following: (A) The plastic bottles are made by the process of blowing (B) The application of thermo-setting resins on sheets of paper, is called laminating process (C) The plastic articles made by placing raw material in the desired moulds, is known as moulding process (D) All the above

Description : Pick up the correct statement from the following: (A) The plastic bottles are made by the process of blowing (B) The application of thermo-setting resins on sheets of paper, is called laminating ... placing raw material in the desired moulds, is known as moulding process (D) All the above

Last Answer : Answer: Option D

How to improve physics for endurance?

Description : I'm working on a PC and when I go upstairs I'm immediately out of breath. How to improve endurance and overall physics? Thanks

Last Answer : Only by training - how else ?? If you are fit so that one of the stairs "breathes" you, start very quickly - walk, run, swim, ride a bike. But if you had in mind the stairs to the Eiffel Tower and you manage a smaller one, your condition is not so "tasty". : D

Agonists affect the receptor molecule in the following manner: A. Alter its amino acid sequence B. Denature the receptor protein C. Alter its folding or alignment of subunits D. Induce covalent bond formation

Description : Agonists affect the receptor molecule in the following manner: A. Alter its amino acid sequence B. Denature the receptor protein C. Alter its folding or alignment of subunits D. Induce covalent bond formation

Last Answer : C. Alter its folding or alignment of subunits

Agonists affect the receptor molecule in the following manner: A. Alter its amino acid sequence B. Denature the receptor protein C. Alter its folding or alignment of subunits D. Induce covalent bond formation

Description : Agonists affect the receptor molecule in the following manner: A. Alter its amino acid sequence B. Denature the receptor protein C. Alter its folding or alignment of subunits D. Induce covalent bond formation

Last Answer : C. Alter its folding or alignment of subunits

Tertiary structure of a protein describes (A) The order of amino acids (B) Location of disulphide bonds (C) Loop regions of proteins (D) The ways of protein folding

Description : Tertiary structure of a protein describes (A) The order of amino acids (B) Location of disulphide bonds (C) Loop regions of proteins (D) The ways of protein folding

Last Answer : Answer : D

Amino acid sequence directs protein folding?

Description : Insulin possesses two polypeptide chains denoted A and B that are linked by disulfide bonds. Upon denaturation by reduction of the SH groups of insulin, followed by reoxidation, only 7% of the ... can these data be reconciled with the hypothesis that the amino acid sequence directs protein folding?

Last Answer : Insulin is synthesized as preproinsulin that is proteolytically processed in the β cells of the islets of Langerhans in the pancreas, to give proinsulin. After synthesis and folding, a section of the ... lacking the C peptide, lacks some of the information necessary to direct the folding process. 

I am an athlete and do plenty of strength training but am looking for a way to increase my speed and endurance when it comes to running. Any advice?

Description : I am an athlete and do plenty of strength training but am looking for a way to increase my speed and endurance when it comes to running. Any advice?

Last Answer : yeah I play football and what u should really work on your explosion get a runnig parachute and maybe a weighted vest and literally in no time your endurance stamina and every thing will have greatly improved

Strength Training Exercises to Increase Endurance ?

Description : Strength Training Exercises to Increase Endurance ?

Last Answer : Staying on top of strength training to increase your endurance is the perfect way to enhance your muscle power. You will be able to raise tendon and ligament strength and lower the risk of both acute and ... , or behind your head. Slowly lower your body back to the floor and repeat at your desire.

_____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Description : _____ is a surface fatigue failure which occurs when the load on the bearing part exceeds the surface endurance strength of the material. (a) Scoring (b) Pitting (c) Corrosion

Last Answer : (b) Pitting

When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Description : When a material is subjected to fatigue loading, the ratio of the endurance limit to the ultimate tensile strength is (a) 0.20 (b) 0.35 (c) 0.50 (d) 0.65

Last Answer : (c) 0.50

Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Description : Factor of safety for fatigue loading is the ratio of (a) elastic limit to the working stress (b) Young's modulus to the ultimate tensile strength (c) endurance limit to the working stress (d) elastic limit to the yield point

Last Answer : (c) endurance limit to the working stress

Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Description : Line joining S yt (yield strength of the material) on mean stress axis and S e (endurance limit of the component) on stress amplitude axis is called as _____ a. Goodman line b. Soderberg line c. Gerber line d. None of the above

Last Answer : b. Soderberg line

Explain Size Factor In Endurance Strength?

Description : Explain Size Factor In Endurance Strength?

Last Answer : Size factor is used to consider the effect of the size on endurance strength. A large size object will have more defects compared to a small one. So, endurance strength is reduced. If K is the size factor, then Actual endurance strength = Theoretical endurance limit x K

What Are The Factors Affecting Endurance Strength?

Description : What Are The Factors Affecting Endurance Strength?

Last Answer : Factors affecting endurance strength are 1. Load ii. Surface finish 2. Size 3. Temperature 4. Impact 5. Reliability

In step growth polymerisation, generally only one type of reaction & some basic mechanism is involved. Step growth polymerisation reaction is not involved in the manufacture of (A) Cross linked polystyrene (B) Phenol formaldehyde resins (C) Polyesters (D) Polyamides

Description : In step growth polymerisation, generally only one type of reaction & some basic mechanism is involved. Step growth polymerisation reaction is not involved in the manufacture of (A) Cross linked polystyrene (B) Phenol formaldehyde resins (C) Polyesters (D) Polyamides

Last Answer : (A) Cross linked polystyrene

Thermosetting resins/polymers as compared to thermoplastic ones are (A) Soluble in all organic solvents (B) More brittle (C) Formed by addition polymerisation only (D) Easily reshaped & reused

Description : Thermosetting resins/polymers as compared to thermoplastic ones are (A) Soluble in all organic solvents (B) More brittle (C) Formed by addition polymerisation only (D) Easily reshaped & reused

Last Answer : (B) More brittle

A chain growth polymerisation reaction consists of three different types of reaction namely initiation reaction, propagation reaction & termination reaction. Chain growth polymerisation reaction is not involved in the manufacture of (A) Siloxane elastomers (B) Polyamides (C) Vinyl polymers (D) Urea-formaldehyde resins

Description : A chain growth polymerisation reaction consists of three different types of reaction namely initiation reaction, propagation reaction & termination reaction. Chain growth polymerisation reaction is not involved ... Siloxane elastomers (B) Polyamides (C) Vinyl polymers (D) Urea-formaldehyde resins

Last Answer : (D) Urea-formaldehyde resins

Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Description : Size reduction of moulding powders, waxes, resins & gums are done in a __________ mill. (A) Cage (B) Hammer (C) Both (A) & (B) (D) Neither (A) nor (B)

Last Answer : (C) Both (A) & (B)

Fibre reinforced plastic (FRP) are (A) Made of glass fibre and thermoplastic resins (B) Anisotropic (C) Made of thermosetting resin and glass fibre (D) Both 'b' & 'c'

Description : Fibre reinforced plastic (FRP) are (A) Made of glass fibre and thermoplastic resins (B) Anisotropic (C) Made of thermosetting resin and glass fibre (D) Both 'b' & 'c'

Last Answer : Option D

Lead is added to 60:40 brass primarily to improve (A) Machinability (B) Corrosion resistance (C) Fluidity (D) Strength

Description : Lead is added to 60:40 brass primarily to improve (A) Machinability (B) Corrosion resistance (C) Fluidity (D) Strength

Last Answer : (A) Machinability

Is folding paper a chemical or physical reaction?

Description : Is folding paper a chemical or physical reaction?

Last Answer : This is a physical change.

Is folding paper a chemical or physical reaction?

Description : Is folding paper a chemical or physical reaction?

Last Answer : This is a physical change.

Why is folding a paper physical change?

Description : Why is folding a paper physical change?

Last Answer : Folding a paper does not form new substances.

Rosin soap is added during paper manufacture to (A) Impart adhesive properties (B) Improve opacity (C) Impart resistance to penetration by liquids (D) None of these

Description : Rosin soap is added during paper manufacture to (A) Impart adhesive properties (B) Improve opacity (C) Impart resistance to penetration by liquids (D) None of these

Last Answer : (C) Impart resistance to penetration by liquids

This natural fiber obtained from the stems of a plant of the nettle family has found popularity in modern fibers with a high wet strength, absorbent but dries quickly, it can be spun or woven, has a high rot and mildew resistance and elasticity 50 percent greater than that of CHEM-92; Multiple Choice: What transuranic element is often used in satellites as a source of heat or power? w) Plutonium-238 x) Strontium-90 y) Cesium-137 z) Uranium-235

Description : This natural fiber obtained from the stems of a plant of the nettle family has found popularity in modern fibers with a high wet strength, absorbent but dries quickly, it can be spun or woven, has a high rot ... a source of heat or power? w) Plutonium-238 x) Strontium-90 y) Cesium-137 z) Uranium-235

Last Answer : ANSWER: W -- PLUTONIUM-238

Write back if this is funny,Hey, do you want to hear a joke about paper oh wait it's tear-able!?

Description : Write back if this is funny,Hey, do you want to hear a joke about paper oh wait it's tear-able!?

Last Answer : HAHAHAHAHAHAHAHAHAHA!!!!!!!!!! That sounds like a dad joke.

Water hammer in a pipeline results from the (A) Bursting of pipelines due to closure by a valve (B) Rapid pressure change due to a rapid change in the rate of flow (C) Pressure increase due to closure of a valve resulting in decrease in rate of flow (D) None of these

Description : Water hammer in a pipeline results from the (A) Bursting of pipelines due to closure by a valve (B) Rapid pressure change due to a rapid change in the rate of flow (C) Pressure increase due to closure of a valve resulting in decrease in rate of flow (D) None of these

Last Answer : (B) Rapid pressure change due to a rapid change in the rate of flow