Mention the purpose of SID and SOD lines

Mention the purpose of SID and SOD lines
by

1 Answer

Answer :

SID (Serial input data line):
It is an input line through which the microprocessor accepts serial data.
SOD (Serial output data line):
It is an output line through which the microprocessor sends output serial data.
by

Related questions

Explain the signals HOLD, READY and SID

Description : Explain the signals HOLD, READY and SID

Last Answer : HOLD indicates that a peripheral such as DMA controller is requesting the use of address bus, data bus and control bus. READY is used to delay the microprocessor ... slow responding peripheral is ready to send or accept data. SID is used to accept serial data bit by bit

SOD pin can drive a D flip-flop? a) SOD cannot drive any flip-flops. b) SOD cannot drive D flip-flop, but can drive any other flop-flops. c) Yes, SOD can drive D flop-flop. d) No, SOD cannot drive any other flop-flops except D flop-flop

Description : SOD pin can drive a D flip-flop? a) SOD cannot drive any flip-flops. b) SOD cannot drive D flip-flop, but can drive any other flop-flops. c) Yes, SOD can drive D flop-flop. d) No, SOD cannot drive any other flop-flops except D flop-flop

Last Answer : b) SOD cannot drive D flip-flop, but can drive any other flop-flops

State the functions of following pins of 8085 1) SOD 2) HLDA

Description : State the functions of following pins of 8085 1) SOD 2) HLDA

Last Answer : 1) SOD: Serial Output data SOD pin is used to transmit data serially from accumulator to the external devices connected to the pin.  2) HLDA: Microprocessor generates HLDA signal to acknowledge requesting device after HOLD signal.

8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Description : 8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Last Answer : c) 4, i,ii,iii

8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Description : 8096 has ___ general purpose I/O ports, Port 2 includes ______ of the following i) two quasi-bidirectional I/O lines ii) two output lines iii) four input lines iv) open drain outputs a) 4, i, iv b) 6, ii, iii c) 4, i,ii,iii d) 6, i, ii, iv

Last Answer : c) 4, i,ii,iii

Moldboard consists of following types : a) General purpose. c) Sod or breaker b) Stubble. d) All of the above

Description : Moldboard consists of following types : a) General purpose. c) Sod or breaker b) Stubble. d) All of the above

Last Answer : All of the above

is the general purpose lying. a) Between stubble and sod b) Between soil and mud c) Between man and machine d) None

Description : is the general purpose lying. a) Between stubble and sod b) Between soil and mud c) Between man and machine d) None

Last Answer :   <!-- [endif] -->Between stubble and sod

A low mold board with gradual twist that completely invert the furrow slice with a minimum of breakup, thus covering vegetative matter thoroughly is called a. Stubble bottom b. sod bottom c. salted mould board d. general purpose bottom

Description : A low mold board with gradual twist that completely invert the furrow slice with a minimum of breakup, thus covering vegetative matter thoroughly is called a. Stubble bottom b. sod bottom c. salted mould board d. general purpose bottom

Last Answer : b. sod bottom

What is the use of addressing modes, mention the different types

Description : What is the use of addressing modes, mention the different types

Last Answer : The various formats of specifying the operands are called addressing modes, it is used to access the operands or data. The different types are as follows • Immediate addressing • Register addressing • Direct addressing • Indirect addressing • Implicit addressing

Mention the categories of instruction and give two examples for each category

Description : Mention the categories of instruction and give two examples for each category

Last Answer : The instructions of 8085 can be categorized into the following five • Data transfer MOV Rd,Rs STA 16-bit • Arithmetic ADD R DCR M • Logical XRI 8-bit RAR • Branching JNZ CALL 16-bit • Machine control HLT NOP

How many machine cycles does 8085 have, mention them

Description : How many machine cycles does 8085 have, mention them

Last Answer : The 8085 have seven machine cycles. They are • Opcode fetch • Memory read • Memory write • I/O read • I/O write • Interrupt acknowledge • Bus idle

How many interrupts does 8085 have, mention them

Description : How many interrupts does 8085 have, mention them

Last Answer : The 8085 has 5 interrupt signals; they are INTR, RST7.5, RST6.5, RST5.5 and TRAP

Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Description : Mention The Various Functional Blocks Of The 8085 Microprocessor.?

Last Answer : Answer :The various functional blocks of the 8085 microprocessor are: Registers Arithmetic logic unit Address buffer Increment / decrement address latch Interrupt control Serial I/O control Timing and control circuitry Instructions decoder and machine cycle encoder.

How many address lines in a 4096 x 8 EPROM CHIP?

Description : How many address lines in a 4096 x 8 EPROM CHIP?

Last Answer : 12 address lines.

How many address lines are needed to address each memory locations in a 2048 x 4 memory chip? a. 10 b. 11 c. 8 d. 12

Description : How many address lines are needed to address each memory locations in a 2048 x 4 memory chip? a. 10 b. 11 c. 8 d. 12

Last Answer : b. 11

If m is a power of 2, the number of select lines required for an m-input mux is: a. m b. 2^m c. log2 (m) d. 2*m

Description : If m is a power of 2, the number of select lines required for an m-input mux is: a. m b. 2^m c. log2 (m) d. 2*m

Last Answer : c. log2 (m)

How many address lines are needed to address each memory location in a 2048 x 4 memory chip? a. 10 b. 11 c. 8 d. 12

Description : How many address lines are needed to address each memory location in a 2048 x 4 memory chip? a. 10 b. 11 c. 8 d. 12

Last Answer : b. 11

Different components on the motherboard of a PC processor unit are linked together by sets or parallel electrical conducting lines. What are these lines called? a. Conductors b. Buses c. Connectors d. Connectively

Description : Different components on the motherboard of a PC processor unit are linked together by sets or parallel electrical conducting lines. What are these lines called? a. Conductors b. Buses c. Connectors d. Connectively

Last Answer : b. Buses

Which of the following does not affect the resolution of a video display image? a. Bandwidth b. Raster scan rage c. Vertical and horizontal lines of resolution d. Screen size

Description : Which of the following does not affect the resolution of a video display image? a. Bandwidth b. Raster scan rage c. Vertical and horizontal lines of resolution d. Screen size

Last Answer : d. Screen size

how many address lines are needed to address each machine location in a 2048 x 4 memory chip? a. 10 b. 11 c. 8 d. 12

Description : how many address lines are needed to address each machine location in a 2048 x 4 memory chip? a. 10 b. 11 c. 8 d. 12

Last Answer : b. 11

Which statement is wrong according to linear decoding : a. Address map is not contiguous. b. Confects occur if two of the select lines become active at the same time c. If all unused address lines are not used as chip selectors then these unused lines become don’t cares d. None of these

Description : Which statement is wrong according to linear decoding : a. Address map is not contiguous. b. Confects occur if two of the select lines become active at the same time c. If all unused address lines are not used as chip selectors then these unused lines become don’t cares d. None of these

Last Answer : d. None of these

Interfacing LCD with 89C51 _____ data lines are used along with the _____ signals. a) 6, RS, RW b) 5, RW, EN c) 8, RS, EN, RW d) 9, RS, EN, RW

Description : Interfacing LCD with 89C51 _____ data lines are used along with the _____ signals. a) 6, RS, RW b) 5, RW, EN c) 8, RS, EN, RW d) 9, RS, EN, RW

Last Answer : a) 6, RS, RW

In 8255, under the I/O mode of operation we have __ modes. Under which mode will have the following features i) A 5 bit control port is available. ii) Three I/O lines are available at Port C. a) 3, Mode2 b) 2, Mode 2 c) 4, Mode 3 d) 3, Mode 2

Description : In 8255, under the I/O mode of operation we have __ modes. Under which mode will have the following features i) A 5 bit control port is available. ii) Three I/O lines are available at Port C. a) 3, Mode2 b) 2, Mode 2 c) 4, Mode 3 d) 3, Mode 2

Last Answer : a) 3, Mode2

In 8279 Strobed input mode, the control line goes low. The data on return lines is strobed in the ____. a) FIFO byte by byte b) FILO byte by byte c) LIFO byte by byte d) LILO byte by byte.

Description : In 8279 Strobed input mode, the control line goes low. The data on return lines is strobed in the ____. a) FIFO byte by byte b) FILO byte by byte c) LIFO byte by byte d) LILO byte by byte.

Last Answer : a) FIFO byte by byte

Who would like to help me bid a final farewell to the TV comic pioneer Sid Caesar?

Description : Who would like to help me bid a final farewell to the TV comic pioneer Sid Caesar?

Last Answer : I only ever saw him in It’s a Mad, Mad, Mad, Mad World, expressively very funny guy.

What is the full form of SID ?

Description : What is the full form of SID ?

Last Answer : Full form of SID Society For International Development.

Can you install a Sid card in an iPhone?

Description : Can you install a Sid card in an iPhone?

Last Answer : Need answer

What does sed sid and sess mean?

Description : What does sed sid and sess mean?

Last Answer : What is the answer ?

How are the children on the other sid of the fence treated by the soldiers boy in the striped pajamas?

Description : How are the children on the other sid of the fence treated by the soldiers boy in the striped pajamas?

Last Answer : Need answer

What does SID mean in scp foundation?

Description : What does SID mean in scp foundation?

Last Answer : site director.

What does SID mean in scp foundation?

Description : What does SID mean in scp foundation?

Last Answer : site director.

Which term would be used to describe an animal which has adapted to a tree-dwelling mode of life? a) deciduous (pron: de-SID-you-us) b) dendritic c) arboreal (pron: ar-BOR-e-al) d) sessile (pron: SESS-ile)

Description : Which term would be used to describe an animal which has adapted to a tree-dwelling mode of life? a) deciduous (pron: de-SID-you-us) b) dendritic c) arboreal (pron: ar-BOR-e-al) d) sessile (pron: SESS-ile)

Last Answer : ANSWER: C -- ARBOREAL

Most of the fungi commonly observed are members of this group of fungi, which includes toadstools, mushrooms and puffballs. This group of fungi is known as: a) Phycomycetes (pron: fI-kO-my-seats) b) Ascomycetes (pron: as-kO-my-seats) c) Basidomycetes (pron: beh-sid-E-O-my-seats) d) Plyocetes (pron: ply-O-seats)

Description : Most of the fungi commonly observed are members of this group of fungi, which includes toadstools, mushrooms and puffballs. This group of fungi is known as: a) Phycomycetes (pron: fI-kO-my-seats) b) Ascomycetes ... ) c) Basidomycetes (pron: beh-sid-E-O-my-seats) d) Plyocetes (pron: ply-O-seats)

Last Answer : ANSWER: C -- Basidomycetes

Explain the purpose of the I/O instructions IN and OUT.

Description : Explain the purpose of the I/O instructions IN and OUT.

Last Answer : The IN instruction is used to move data from an I/O port into the accumulator. The OUT instruction is used to move data from the accumulator to an I/O port. The IN & OUT instructions are used only on microprocessor, which use a separate address space for interfacing.

Which is an integral part of any microcomputer system and its primary purpose is to hold program and data: a. Memory unit b. Register unit c. A and B d. None of these

Description : Which is an integral part of any microcomputer system and its primary purpose is to hold program and data: a. Memory unit b. Register unit c. A and B d. None of these

Last Answer : a. Memory unit

Registers, which are partially visible to users and used to hold conditional, are known as a. PC b. Memory address registers c. General purpose register d. Flags

Description : Registers, which are partially visible to users and used to hold conditional, are known as a. PC b. Memory address registers c. General purpose register d. Flags

Last Answer : c. General purpose register

The first electronic general purpose digital computer built by Motley and Accrete called ENIAC did not work on the stored program concept. How many number s could it store in its internal memory? a. 100 b. 20 c. 40 d. 80

Description : The first electronic general purpose digital computer built by Motley and Accrete called ENIAC did not work on the stored program concept. How many number s could it store in its internal memory? a. 100 b. 20 c. 40 d. 80

Last Answer : b. 20

Most of the inexpensive personal computers do not have any disk or diskette drive. What is the name of such computes? a. Home computers b. Diskless computers c. Dedicated computers d. General purpose computers

Description : Most of the inexpensive personal computers do not have any disk or diskette drive. What is the name of such computes? a. Home computers b. Diskless computers c. Dedicated computers d. General purpose computers

Last Answer : a. Home computers

The first electronic general purpose digital computer built by Mauchly and Eckert called ENIA did not work on the stored program principle. How many numbers could it store in its internal memory? a. 100 b. 20 c. 40 d. 80

Description : The first electronic general purpose digital computer built by Mauchly and Eckert called ENIA did not work on the stored program principle. How many numbers could it store in its internal memory? a. 100 b. 20 c. 40 d. 80

Last Answer : b. 20

Which register is a temporary storage location: a. general purpose register b. dedicated register c. A and B d. none of these

Description : Which register is a temporary storage location: a. general purpose register b. dedicated register c. A and B d. none of these

Last Answer : c. A and B

There are primarily two types of register: a. general purpose register b. dedicated register c. A and B d. none of these

Description : There are primarily two types of register: a. general purpose register b. dedicated register c. A and B d. none of these

Last Answer : c. A and B

What Are The Boons And Banes Of Having More General Purpose Registers In A Microprocessor.?

Description : What Are The Boons And Banes Of Having More General Purpose Registers In A Microprocessor.?

Last Answer : Answer :If there are more general purpose registers the program writing process is more flexible and convenient. The number of bits that would be required to detect the registers would increase with more ... on the chip. This can create problems in adding / implementing other functions on the chip.

Describe the functions of General purpose registers of 8086 microprocessor.

Description : Describe the functions of General purpose registers of 8086 microprocessor.

Last Answer : (i) General Purpose Registers of 8086 1. AX (Accumulator) - Used to store the result for arithmetic / logical operations All I/O data transfer using IN & OUT instructions use A ... Index - acts as the destination for string movement instructions Used to hold offset address of Extra segment.

The purpose of the microprocessor is to control ______

Description : The purpose of the microprocessor is to control ______  A. memory B. switches C. processing D. tasks

Last Answer : The purpose of the microprocessor is to control memory 

how did my new sod get webworms

Description : how did my new sod get webworms

Last Answer : Need Answer

Just put down palmetto sod how much do I water to start the yard is really shaded

Description : Just put down palmetto sod how much do I water to start the yard is really shaded

Last Answer : Water in the morning for about an hour, then in the evening dig down 6" and if you fell moisture then water less, if it feels dry, repeat the morning wattering until you can feel moisture.

what are the differences in types of sod?

Description : what are the differences in types of sod?

Last Answer : Need Answer

How to get rid of mushrooms growing in my new sod yard.

Description : How to get rid of mushrooms growing in my new sod yard.

Last Answer : what a shame....if it's not too many...you could use straight white vinegar in an old pointed top mustard container.......................if that does not work for you...this is a ... & pets away until a good rain washed it in....also whereever you bought your sod might even have a better idea.

Can you lay sod on top of dirt that is on top of existing grass?

Description : Can you lay sod on top of dirt that is on top of existing grass?

Last Answer : That is a hard question to answer.....but I would think that the new sod over old grass might work if the old grass is cut super short.............then the new sod has to be kept wet until the new sod takes.

What plains Indians lived On the great plains where would you find lodges covered in sod?

Description : What plains Indians lived On the great plains where would you find lodges covered in sod?

Last Answer : What is the answer ?