State the principle of operation of the gear box in terms of Torque, speed and diameter of the gear.

State the principle of operation of the gear box in terms of Torque, speed and diameter of the gear.
by

1 Answer

Answer :

In a gear box, the counter shaft is mashed to the clutch with a use of a couple of gear. So the counter shaft is always in running condition. When the counter shaft is bring in contact with the main shaft by use of meshing gears, the main shaft start to rotate according to the gear ratio. When want to change the gear ratio, simply press the clutch pedal which disconnect the counter shaft with engine and change connect the main shaft with counter shaft by another gear ratio by use of gearshift lever. In a gear box, the gear teeth and other moving metal must not touch. They must be continuously separated by a thin film of lubricant. This prevents excessive wear and early failure. Therefore a gearbox runs partially filled with lubricant oil.
by

Related questions

Function of gear box is to (A) Reduce the speed (B) Obtain variable speed (C) Increase the speed (D) Produce high torque

Description : Function of gear box is to (A) Reduce the speed (B) Obtain variable speed (C) Increase the speed (D) Produce high torque

Last Answer : (B) Obtain variable speed

What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Description : What is the maximum principle stress induced in a solid shaft of 40 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 150 kN.mm respectively? a. 21.69 N/mm2 b. 28.1 N/mm2 c. 50.57 N/mm2 d. 52.32 N/mm2

Last Answer : c. 50.57 N/mm2

What gear train provides less torque?

Description : What gear train provides less torque?

Last Answer : Need answer

What are the initial and final torque values for A321 main landing gear wheels?

Description : What are the initial and final torque values for A321 main landing gear wheels?

Last Answer : The initial or bearing setting torque value for A321 main landing gear wheel is 310 ft.-lbs. and the final torque value is 160 ft.-lbs.

If the centrifugal switch or relay used for cutting out the starting winding of a split-phase induction motor fails to open once the motor is in operation, the _____________. A. motor will overspeed B. starting winding will burn out C. motor will immediately stall under load D. motor torque will be above normal at rated speed

Description : If the centrifugal switch or relay used for cutting out the starting winding of a split-phase induction motor fails to open once the motor is in operation, the _____________. A. motor will overspeed B ... C. motor will immediately stall under load D. motor torque will be above normal at rated speed

Last Answer : Answer: B

Is the steering gear box the same on a 1954 and a 1956 International 300 tractor?

Description : Is the steering gear box the same on a 1954 and a 1956 International 300 tractor?

Last Answer : Yes it is check it out here http://www.hemmings.com/hmn/stories/2008/08/01/hmn_feature37.html

Does anyone know where to get used -complete gear box assembly for an early 7111 Simplicty tractor. thanks ?

Description : Does anyone know where to get used -complete gear box assembly for an early 7111 Simplicty tractor. thanks ?

Last Answer : I would check Ebay , you can find almost anything on there . I would also check craiglist.com on a daily basis , because you can almost always find great deals on there for anything you can think of.

Splines are commonly used in (A) Machine tool gear box (B) Automobile gear box (C) Hoist and crane gear box (D) Bicycle

Description : Splines are commonly used in (A) Machine tool gear box (B) Automobile gear box (C) Hoist and crane gear box (D) Bicycle

Last Answer : (B) Automobile gear box

What Is The Main Purpose Of A Gear Box In A Vehicle?

Description : What Is The Main Purpose Of A Gear Box In A Vehicle?

Last Answer : To vary the torque at the road vehicles.

Gears are generally used in the transmission box are ∙ spur gear only ∙ helical gear only ∙ helical and spur gear gears ∙ bevel gears

Description : Gears are generally used in the transmission box are ∙ spur gear only ∙ helical gear only ∙ helical and spur gear gears ∙ bevel gears

Last Answer : ∙ helical gear only

tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Description : tractors are generally fitted with: A)sliding mesh gear box B)constant mesh gear box C)both (a) & (b) D)synchromesh gear box

Last Answer : A)sliding mesh gear box

Describe working of constant mesh gear box with neat sketch.

Description : Describe working of constant mesh gear box with neat sketch.

Last Answer : Working of constant mesh gear box: A simplified diagram of constant mesh box has been shown in Figure. In this gear box, all gears on the main transmission shaft are constantly connected to corresponding ... In this way by sliding the second dog clutch, second and first gears are obtained.

Describe the working of recirculating ball type steering gear box with sketch.

Description : Describe the working of recirculating ball type steering gear box with sketch.

Last Answer : Working of Recirculating ball type steering gear box: It consists of worm at the end of steering rod. A nut is mounted on the worm with two sets of balls in the grooves of the worm, in between ... and actual the link rod through the drop arm, resulting in the desired steering of the wheels.

Name the steering gear box used in following: (i) Maruti ‘Alto’ (ii) Tata ‘Sumo’ (iii) Ashok Leyland Truck (iv) Road Roller

Description : Name the steering gear box used in following:  (i) Maruti ‘Alto’  (ii) Tata ‘Sumo’  (iii) Ashok Leyland Truck (iv) Road Roller

Last Answer : (i) Maruti ‘Alto’=========Rack and Pinion Type Gear Box. (ii) Tata ‘Sumo’==========Recireulating Ball Type Gear Box. (iii) Ashok Leyland Truck === Worm and Nut Type Gear Box (iv) Road Roller=========== Worm and Roller Type Steering Gear Box

Write the functions of : i) Blades – ii) Nacelle – iii) Shaft – iv) Gear box –

Description : Write the functions of : i) Blades – ii) Nacelle – iii) Shaft – iv) Gear box –

Last Answer : i) Blades - Convert wind energy into usable mechanical energy. Aerodynamically optimized structure of blades help to capture maximum wind power even in normal operation. ii) Nacelle - Protects ... high speed - drives the generator. iv) Gear box - Controls rotational speed of generator.

Compare constant mesh gear box with synchromesh gear box

Description : Compare constant mesh gear box with synchromesh gear box

Last Answer : Sr No. constant mesh gear box  synchromesh gear box  1. It has need of double declutching . No need of double declutching as in case of constant mesh gearbox. 2. Problem in ... noisy as helical gears are used. 4. It has more vibration. It has less vibration.

Describe the necessity of Gear box in Automobile.

Description : Describe the necessity of Gear box in Automobile.

Last Answer : Necessity of gear box: The engine delivers its full power at high speed and its direction of rotation is not reversible. When a vehicle starts from rest, hill climbing, accelerating and meeting ... main purpose of gearbox to provide speed variations in road wheels by keeping engine speed constant.

How To Calculate The Number Of Teeth In A Gear If Given The Module And Pitch Circle Diameter?

Description : How To Calculate The Number Of Teeth In A Gear If Given The Module And Pitch Circle Diameter?

Last Answer :  Pitch = Module* 3.14 (pie value)  Number of teeth = Pitch circle diameter/ pitch

In accordance with Coast Guard Regulations (46 CFR), a steering gear feeder circuit from the emergency switchboard or alternate power supply must have the capacity for continuous operation of the rudder 15° side to side in not more than 60 seconds for a A. 1/4 hour B. 1/2 hour C. 1 hour D. 2 hours

Description : In accordance with Coast Guard Regulations (46 CFR), a steering gear feeder circuit from the emergency switchboard or alternate power supply must have the capacity for continuous operation of the rudder 15° side to side in not more than 60 seconds for a A. 1/4 hour B. 1/2 hour C. 1 hour D. 2 hours

Last Answer : Answer: B

Ken Adams tells the loan officer at Allied Irish Bank that Cork really needs a shop that offers high -quality fishing gear to sports enthusiasts and provides the service and advice that so many people need. No other shop in the area seems to provide this combination. Ken is trying to use ------ to support his request for a loan to start such a retail operation. A)product assortment B)location analysis C)product mix depth D)retail positioning

Description : Ken Adams tells the loan officer at Allied Irish Bank that Cork really needs a shop that offers high -quality fishing gear to sports enthusiasts and provides the service and advice that so ... such a retail operation. A)product assortment B)location analysis C)product mix depth D)retail positioning

Last Answer : D)retail positioning

The torque produced by a DC motor armature is the product of the force acting at the armature surface multiplied by _____________. A. work done by the armature in one revolution B. effective armature diameter at which the force acts C. maximum moment arm at the center of rotation of the armature D. perpendicular distance to its center of rotation

Description : The torque produced by a DC motor armature is the product of the force acting at the armature surface multiplied by _____________. A. work done by the armature in one revolution B. effective ... arm at the center of rotation of the armature D. perpendicular distance to its center of rotation

Last Answer : Answer: D

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the diameter of each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. Permissible tensile stress is 80N/mm2. a) 27mm b) 25mm c) 23mm d) 21mm

Last Answer : a) 27mm

If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Description : If 8 bolts are emplaced in a clamp coupling with shaft diameter 80mm d, calculate the tensile force on each bolt if coefficient of friction is 0.3 and torque transmitted is 4000N-m. a) 51234.4N b) 45968.3N c) 41666.7N d) None of the listed

Last Answer : c) 41666.7N

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and height of the key being 14mm and 80mm respectively. Find the compressive stress induced in the key. a) 70.1 N/mm2 b) 51.6N/mm2 c) 45.5N/mm2 d) None of the listed

Last Answer : b) 51.6N/mm2

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Description : Two shafts A and B are made of same material. The diameter of shaft A is twice that of B. The torque transmitted by shaft A will be (A) Twice that of B (B) Four times that of B (C) Eight times that of B (D) Sixteen times that of B

Last Answer : (C) Eight times that of B

A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Description : A muff coupling is connecting two shafts. The torque involved is 650N-m. The shaft diameter is 45mm with length and breadth of the key being 14mm and 80mm respectively. Find the shear stress induced in the key. a) 30.2N/mm2 b) 25.8N/mm2 c) 34.4N/mm2 d) None of the listed

Last Answer : b) 25.8N/mm2

The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these

Description : The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these

Last Answer : (B) Have different diameters

If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque when t attains maximum shear stress fs the ratio of inner diameter to outer diameter, is 17/64 (fs/N) (A) 1/2 (B) 1/3 (C) 1/4 (D) 1/5

Description : If the strain energy stored per unit volume in a hollow shaft subjected to a pure torque  when t attains maximum shear stress fs  the ratio of inner diameter to outer diameter, is 17/64  (fs/N)  (A) 1/2  (B) 1/3  (C) 1/4  (D) 1/5

Last Answer : (C) 1/4 

A solid circular shaft of diameter d is subjected to a torque T. The maximum normal stress induced in the shaft, is (A) Zero (B) 16T/ 3 (C) 32T/ 3 (D) None of these

Description : A solid circular shaft of diameter d is subjected to a torque T. The maximum normal stress induced  in the shaft, is  (A) Zero  (B) 16T/ 3 (C) 32T/ 3 (D) None of these

Last Answer : (B) 16T/ 3

A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Description : A hollow shaft has an inner diameter of 3.7 cm and an outer diameter of 4.0 cm. A 1 kN-m torque is applied to this shaft. What is the shear stress at the mid-radius of this shaft? (a) 117Mpa (b) 178 Mpa (c) 286 Mpa (d) 363 Mpa

Last Answer : (c) 286 Mpa

A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Description : A solid circular shaft of diameter 100 mm is subjected to an axial stress of 50 Mpa. It is further subjected to a torque of 10 kNm. The maximum principal stress experienced on the shaft is closest to (a) 41Mpa (b) 82 Mpa (c) 164 Mpa (d) 204 Mpa

Last Answer : (b) 82 Mpa

A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Description : A solid shaft has diameter 80 mm. It is subjected to a torque of 4 KNm. The maximum shear stress induced in the shaft would be (a) 75/p N/mm2 (b) 250/p N/mm2 (c) 125/p N/mm2 (d) 150/p N/mm2

Last Answer : (c) 125/p N/mm2

Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Description : Torque and bending moment of 100 kN.m and 200 kN.m acts on a shaft which has external diameter twice of internal diameter. What is the external diameter of the shaft which is subjected to a maximum shear stress of 90 N/mm2? a. 116.5 mm b. 233.025 mm c. 587.1 mm d. 900 mm

Last Answer : c. 587.1 mm

What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Description : What is the maximum shear stress induced in a solid shaft of 50 mm diameter which is subjected to both bending moment and torque of 300 kN.mm and 200 kN.mm respectively? a. 9.11 N/mm2 b. 14.69 N/mm2 c. 16.22 N/mm2 d. 20.98 N/mm2

Last Answer : b. 14.69 N/mm2

What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Description : What is the shear stress acting on the outer surface of a hollow shaft subjected to a torque of 100 Nm?(The inner and outer diameter of the shaft is 15 mm and 30 mm respectively.) a. 50.26 N/mm2 b. 40.24 N/mm2 c. 20.120 N/mm2 d. 8.74 N/mm2

Last Answer : c. 20.120 N/mm2

The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Description : The torque transmitted by a hollow shaft of outer diameter (D) and inner diameter (d) (a)π/4fs(D2-d2)/D (b) π/4fs(D3-d3)/D (c) π/4fs(D4-d4)/D (d) π/4fs(D4-d4)/D

Last Answer : (c) π/4fs(D4-d4)/D

Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Description : Two shafts in torsion will have equal strength if a. Only diameter of the shafts is same b. Only angle of twist of the shaft is same c. Only material of the shaft is same d. Only torque transmitting capacity of the shaft is same

Last Answer : d. Only torque transmitting capacity of the shaft is same

Can someone explain gear ratios on a 21 speed bicycle to me?

Description : Can someone explain gear ratios on a 21 speed bicycle to me?

Last Answer : Easiest: Smallest # of teeth on the front and largest amount on the back (Think climbing hills) Hardest: Largest # of teeth on the front and smallest amount on the back. (Think flat sprints and descending fast)

Would the transition from a multiple-gear (10/14/21 gears) bike to a single-speed/fixed-speed one be difficult?

Description : Would the transition from a multiple-gear (10/14/21 gears) bike to a single-speed/fixed-speed one be difficult?

Last Answer : It would not be too hard if you’re handy. But my unsolicited opinion is fixed gear bikes are lame for most purposes, and are currently trendy things white people like.

determine the speed of rotation of a 20 tooth gear when it is driven by a 40 tooth gear and rotating at 10 rpm?

Description : determine the speed of rotation of a 20 tooth gear when it is driven by a 40 tooth gear and rotating at 10 rpm?

Last Answer : i am the one that asked i dont know the answer

Capacity of a rotary gear pump can be varied by (A) Changing the speed of rotation (B) Bleeding air into suction (C) Bypassing liquid from the suction or discharge line (D) All (A), (B) and (C)

Description : Capacity of a rotary gear pump can be varied by (A) Changing the speed of rotation (B) Bleeding air into suction (C) Bypassing liquid from the suction or discharge line (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce the approach angle to 1.5deg (150ft/mile), add 15kts to all speeds, keep the aeroplane clean (no flaps or gear) and fly it into the surface c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Description : The method of alighting the aeroplane on water during a ditching is to: a. Carry out a normal approach with flaps and gear selected as normal but to calculate all speeds plus 10kts b. Reduce ... d. Fly a normal approach to stalling speed and then drop the aeroplane vertically onto the water

Last Answer : c. Fly a normal approach but keep the gear up and land at lowest possible speed with the nose raised for the tail to strike first

A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system (in SI units) is given below: Δ P/L = 375 × 10 3 VOM + 10.94 × 10 6 V2 OM (SI units) If water is to be used as the fluidising medium, in actual operation, the above bed has a height = 1 m. What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Description : A bed of spherical particles (specific gravity 2.5) of uniform size 1500 μm is 0.5 m in diameter and 0.5 m high. In packed bed state, the porosity may be taken as 0.4. Ergun's equation for the above fluid-particle system ... What is the porosity of the fluidised bed? (A) 0.2 (B) 0.5 (C) 0.7 (D) 0.8

Last Answer : (C) 0.7

Draw block diagram of frequency meter and state it’s principle of operation

Description : Draw block diagram of frequency meter and state it’s principle of operation

Last Answer : Block diagram Principle  The signal may be amplified before being applied to the Schmitt trigger. The Schmitt trigger converts the input signal into a square wave with fast rise and fall times, ... time interval between start and stop gate then, frequency of unknown signalis, f = N / t

State the principle of operation of d.c. motor.

Description : State the principle of operation of d.c. motor.

Last Answer : When a current carrying conductor is placed in a magnetic field, the conductor experiences the force. The magnitude of force is given by F = BIL newton  where F – Force   B – maximum flux density   I – Current   L – Length of conductor

State principle of operation of piezo-electric transducer. State its application.

Description : State principle of operation of piezo-electric transducer. State its application.

Last Answer : The piezoelectric element used for converting mechanical movement into electric signals. The mechanical deformation generates charges and this charge appears as a voltage across the electrodes.  ... destructive test (NDT) equipments 6. Piezoelectric materials are used in ultrasonic transducers. 

Explain the principle of operation of solenoid. State two parameters on which selection of solenoid is based.

Description : Explain the principle of operation of solenoid. State two parameters on which selection of solenoid is based.

Last Answer : Diagram : Principle: A solenoid is a simple electromagnetic device that converts electrical energy directly into linear mechanical motion, but it has a very short stroke (length of movement), ... Parameters on which selection of solenoid is based1. Size 2. Flow capacity 3. Applied Voltage

State the working principle and operation of Automatic power factor controller used in Transmission and Distribution system.

Description : State the working principle and operation of Automatic power factor controller used in Transmission and Distribution system.

Last Answer : Diagram of Automatic over factor controller Automatic Power factor control: The pf controller is used to maintain the pf at unity across the lines it is connected. Maintaining the pf at ... the load demand in the system is increased. 8. Check if power transformer compensation is provided.

State the principle of operation of a dc motor.

Last Answer : Principle of operation of a dc motor: When a current carrying conductor is placed in a magnetic field, the conductor experiences the mechanical force. The magnitude of force is given by  F = BIL newton  where F – Force , B – Maximum flux density , I – Current , L – Active length of conductor