In a token ring network the transmission speed is 10^7 bps and the propagation speed is 200 metres/micro second. The 1- bit delay in this network is equivalent to: a. 500 metres of cable. b. 200 metres of cable. c. 20 metres of cable. d. 50 metres of cable

In a token ring network the transmission
speed is 10^7 bps and the propagation
speed is 200 metres/micro second. The 1-
bit delay in this network is equivalent to:
a. 500 metres of cable.
b. 200 metres of cable.
c. 20 metres of cable.
d. 50 metres of cable
by

1 Answer

Answer :

c. 20 metres of cable.
by

Related questions

If delaysare recorded as 10 bit numbers in a 50 router network, and delay vectorsare exchanged twicea second,how muchbandwidth per fill duplex line is occupied by the distributedrouting algorithm? A. 500 bps B. 1500 bps C. 5 bps D. 1000 bps

Description : If delaysare recorded as 10 bit numbers in a 50 router network, and delay vectorsare exchanged twicea second,how muchbandwidth per fill duplex line is occupied by the distributedrouting algorithm? A. 500 bps B. 1500 bps C. 5 bps D. 1000 bps

Last Answer : 1000 bps

A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of an acknowledgement is 100 bytes and the transmission rate at the receiver is 8 Kbps. The one-way propagation delay is 100 milliseconds. Assuming no frame is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Description : A sender uses the Stop-and-Wait ARQ protocol for reliable transmission of frames. Frames are of size 1000 bytes and the transmission rate at the sender is 80 Kbps (1Kbps = 1000 bits/second). Size of ... is lost, the sender throughput is __________ bytes/second. a. 2500 b. 2000 c. 1500 d. 500

Last Answer : a. 2500

Suppose that the one-way propagation delay for a 100 Mbps Ethernet having 48-bit jamming signal is 1.04 micro-seconds. The minimum frame size in bits is: a. 112 b. 160 c. 208 d. 256

Description : Suppose that the one-way propagation delay for a 100 Mbps Ethernet having 48-bit jamming signal is 1.04 micro-seconds. The minimum frame size in bits is: a. 112 b. 160 c. 208 d. 256

Last Answer : d. 256

In which topology, if a computer’s network cable is broken, whole network goes down. a. Ring b. Star c. Bus d. token ring

Description : In which topology, if a computer’s network cable is broken, whole network goes down. a. Ring b. Star c. Bus d. token ring

Last Answer : c. Bus

A pure ALOHA Network transmits 200 bit frames using a shared channel with 200 Kbps bandwidth. If the system (all stations put together) produces 500 frames per second, then the throughput of the system is ______. a. 0.384 b. 0.184 c. 0.286 d. 0.58

Description : A pure ALOHA Network transmits 200 bit frames using a shared channel with 200 Kbps bandwidth. If the system (all stations put together) produces 500 frames per second, then the throughput of the system is ______. a. 0.384 b. 0.184 c. 0.286 d. 0.58

Last Answer : b. 0.184

Suppose the round trip propagation delay for a 10 Mbps Ethernet having 48-bit jamming signal is 46.4 ms. The minimum frame size is a. 94 b. 416 c. 464

Description : Suppose the round trip propagation delay for a 10 Mbps Ethernet having 48-bit jamming signal is 46.4 ms. The minimum frame size is a. 94 b. 416 c. 464

Last Answer : c. 464

State weather the following statement is true or false for Token Bus 1).It is a linear or tree- shaped cable onto which the stations are attached. 2). the token propagates around the logical ring, with only the token holder being permitted to transmit frames 3). In this token bus arrangement The physical order in which the stations are connected to the cable is very important. A. 1. False, 2. true, 3. true B. 1. true, 2. false, 3. false C. 1. false, 2. false, 3. false D. 1. true, 2. true, 3. false

Description : State weather the following statement is true or false for Token Bus 1).It is a linear or tree- shaped cable onto which the stations are attached. 2). the token propagates around the logical ring, with only the token holder ... 3. false C. 1. false, 2. false, 3. false D. 1. true, 2. true, 3. false

Last Answer : D. 1. true, 2. true, 3. false

Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is __________. a. 400 bps b. 800 bps c. 1600 bps d. 3200 bps

Description : Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is __________. a. 400 bps b. 800 bps c. 1600 bps d. 3200 bps

Last Answer : d. 3200 bps

A device is sending out data at the rate of 2000 bps. How long does it take to send a file of 1,00,000 characters ? a. 50 b. 200 c. 400 d. 800

Description : A device is sending out data at the rate of 2000 bps. How long does it take to send a file of 1,00,000 characters ? a. 50 b. 200 c. 400 d. 800

Last Answer : c. 400

In the _______ method, thestations in a network areorganizedin a logical ring. A) reservation B) polling C) token passing D) none of the above

Description : In the _______ method, thestations in a network areorganizedin a logical ring. A) reservation B) polling C) token passing D) none of the above

Last Answer : token passing

Which of the following statements is TRUE about CSMA/CD a. IEEE 802.11 wireless LAN runs CSMA/CD protocol b. Ethernet is not based on CSMA/CD protocolc. CSMA/CD is not suitable for a high propagation delay network like satellite network d. There is no contention in a CSMA/CD network

Description : Which of the following statements is TRUE about CSMA/CD a. IEEE 802.11 wireless LAN runs CSMA/CD protocol b. Ethernet is not based on CSMA/CD protocol c. CSMA/CD is not suitable for a high propagation delay network like satellite network d. There is no contention in a CSMA/CD network

Last Answer : CSMA/CD is not suitable for a high propagation delay

An analog signal carries 4 bits in each signal unit. If 1000 signal units are sent per second, then baud rate and bit rate of the signal are ............... and .............. (A) 4000 bauds \ sec & 1000 bps (B) 2000 bauds \ sec & 1000 bps (C) 1000 bauds \ sec & 500 bps (D) 1000 bauds \ sec & 4000 bps

Description : An analog signal carries 4 bits in each signal unit. If 1000 signal units are sent per second, then baud rate and bit rate of the signal are ............... and .............. (A) 4000 bauds \ sec & ... (B) 2000 bauds \ sec & 1000 bps (C) 1000 bauds \ sec & 500 bps (D) 1000 bauds \ sec & 4000 bps

Last Answer : (D) 1000 bauds \ sec & 4000 bps Explanation: Bit rate is the number of bits per second. Baud rate is the number of signal units per second. Baud rate is less than or equal to the bit rate. Baud rate = 1000 bauds per second (baud/s) Bit rate = 1000 x 4 = 4000 bps

The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channelcapacity. Assuming that processing delay is negligible, the minimum number of bits for the sequence number field in a frame for maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D

Description : The distance between two stations M and N is L kilometers. All frames are K bits long. The propagation delay per kilometer is t seconds. Let R bits/second be the channel capacity. Assuming that processing ... maximum utilization, when the sliding window protocol used is: a. A b. B c. C d. D

Last Answer : c. C

The probability thata singlebit will be inerror on a typical public telephone lineusing 4800 bps modem is 10 to the power -3. If no error detection mechanism is used, the residual error ratefor a communicationline using 9-bit frames is approximately equal to A. 0.003 B. 0.009 C. 0.991 D. 0.999 E. None of the above

Description : The probability thata singlebit will be inerror on a typical public telephone lineusing 4800 bps modem is 10 to the power -3. If no error detection mechanism is used, the residual error ratefor a communicationline using 9-bit frames is ... to A. 0.003 B. 0.009 C. 0.991 D. 0.999 E. None of the above

Last Answer : 0.009

What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Description : What medium is used by IBM token ring network that operates at either 4 Mbps or 16 Mbps? A. Twisted pair B. Coaxial cable C. Fiber-optic D. Parallel-wire line

Last Answer : A. Twisted pair

If the bit rate for a16-QAM signal is 4000 bps, what is the baudrate? A) 300 B) 400 C) 1000 D) 1200

Description : If the bit rate for a16-QAM signal is 4000 bps, what is the baudrate? A) 300 B) 400 C) 1000 D) 1200

Last Answer : 1000

If the bit rate for an FSK signal is1200 bps, thebaud rate is ________. A) 300 B) 400 C) 600 D) 1200

Description : If the bit rate for an FSK signal is1200 bps, thebaud rate is ________. A) 300 B) 400 C) 600 D) 1200

Last Answer : 1200

f the bit rate for an ASK signal is1200 bps, thebaud rate is ________. A) 300 B) 400 C) 600 D) 1200

Description : f the bit rate for an ASK signal is1200 bps, thebaud rate is ________. A) 300 B) 400 C) 600 D) 1200

Last Answer : 1200

The minimum frame size required for a CSMA/CD based computer network running at 1 Gbps on a 200m cable with a link speed of 2 × 108m/s is a. 125 bytes b. 250 bytes c. 500 bytes d. None of these

Description : The minimum frame size required for a CSMA/CD based computer network running at 1 Gbps on a 200m cable with a link speed of 2 × 108m/s is a. 125 bytes b. 250 bytes c. 500 bytes d. None of these

Last Answer : b. 250 bytes

What arethe most commonly used transmission speeds in BPS usedin datacommunication? A. 300 B. 1200 C. 2400 D. 9600 E. None of the above

Description : What arethe most commonly used transmission speeds in BPS usedin datacommunication? A. 300 B. 1200 C. 2400 D. 9600 E. None of the above

Last Answer : 9600

Which transmission media provides the highest transmission speed in a network? a. coaxial cable b. twisted pair cable c. optical fiber d. electrical cable

Description : Which transmission media provides the highest transmission speed in a network? a. coaxial cable b. twisted pair cable c. optical fiber d. electrical cable

Last Answer : c. optical fiber

Which transmission media provides the highest transmission speed in a network? a) coaxial cable b) twisted pair cable c) optical fiber d) electrical cable

Description : Which transmission media provides the highest transmission speed in a network? a) coaxial cable b) twisted pair cable c) optical fiber d) electrical cable

Last Answer : c) optical fiber

Inthe _________ method, a special packet called a ______ circulates through the ring. A) reservation: control frame B) polling: poll request C) token passing: token D) none of the above

Description : Inthe _________ method, a special packet called a ______ circulates through the ring. A) reservation: control frame B) polling: poll request C) token passing: token D) none of the above

Last Answer : token passing: token

______ is the most widelyused local area networkprotocol. A) Token Ring B) Token Bus C) Ethernet D) none of the above

Description : ______ is the most widelyused local area networkprotocol. A) Token Ring B) Token Bus C) Ethernet D) none of the above

Last Answer : Ethernet

The _____ houses the switches in token ring. A. transceiver B. nine-pin connector C. MAU D. NIC E. None of the above

Description : The _____ houses the switches in token ring. A. transceiver B. nine-pin connector C. MAU D. NIC E. None of the above

Last Answer : MAU

Terminators are used in which topology? a. Bus b. Star c. Ring d. token ring

Description : Terminators are used in which topology? a. Bus b. Star c. Ring d. token ring

Last Answer : a. Bus

The Token Ring implementation works on the __ mode. A. Contention B. Reservation C. Round Robin D. None

Description : The Token Ring implementation works on the __ mode. A. Contention B. Reservation C. Round Robin D. None

Last Answer : C. Round Robin

Explain the frame format for token ring and token bus

Description : Explain the frame format for token ring and token bus

Last Answer : Access method: Token passing _ Priority and reservation _ Time limits _ Monitor stations

What is the advantage of FDDI over a basic Token Ring?

Description : What is the advantage of FDDI over a basic Token Ring?

Last Answer : Fiber distributed Data Interface. A high speed token ring networking technology designed to run over optical fiber. FDDI is able to tolerate a single break in the cable or failure of one station due ... token before it is allowed to transmit. 802.5 and FDDI are examples of token ring networks.

A pure ALOHA Network transmit 200 bit frames using a shared channel with 200 Kbps bandwidth. If the system (all stations put together) produces 500 frames per second, then the throughput of the system is .............. (A) 0.384 (B) 0.184 (C) 0.286 (D) 0.586

Description : A pure ALOHA Network transmit 200 bit frames using a shared channel with 200 Kbps bandwidth. If the system (all stations put together) produces 500 frames per second, then the throughput of the system is .............. (A) 0.384 (B) 0.184 (C) 0.286 (D) 0.586

Last Answer : (B) 0.184

Usually, it takes10-bits to represent one character. How many characters can betransmittedat a speed of 1200 BPS? A. 10 B. 12 C. 120 D. 1200 E. None of the above

Description : Usually, it takes10-bits to represent one character. How many characters can betransmittedat a speed of 1200 BPS? A. 10 B. 12 C. 120 D. 1200 E. None of the above

Last Answer : 120

The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Description : The total propagation delay time from transmission to reception of signals from a ground transmitter to ground receiver with angle of elevation at 10 degrees respectively is A. 273 ms B. 239 ms C. 275 ms D. 260 ms

Last Answer : A. 273 ms

The maximum length of a "thick" Ethernet cable is ……….. A. 100 meters B. 200 meters C. 500 meters D. 1000meters

Description : The maximum length of a "thick" Ethernet cable is ……….. A. 100 meters B. 200 meters C. 500 meters D. 1000meters

Last Answer : C. 500 meters

Consider a CSMA/CD network that transmits data at a rate of 100 Mbps (108 bits per second) over a 1 km (kilometre) cable with no repeaters. If the minimum frame size required for this network is 1250 bytes, what is the signal speed (km/sec) in the cable? a. 8000 b. 10000 c. 16000 d. 20000

Description : Consider a CSMA/CD network that transmits data at a rate of 100 Mbps (108 bits per second) over a 1 km (kilometre) cable with no repeaters. If the minimum frame size required for this network is 1250 bytes, what is the signal speed (km/sec) in the cable? a. 8000 b. 10000 c. 16000 d. 20000

Last Answer : d. 20000

A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Description : A centrifugal pump has the following specifications: Power = 4 H.P.; Speed = 800 rpm Head = 8 metres Flow = 1000 litres/minutes. If its speed is halved, the new discharge will be __________ litres/minute. (A) 500 (B) 200 (C) 1000 (D) 750

Last Answer : (A) 500

In a digital transmission, the receiver clock is 0.1 percent faster than the sender clock. How many extra bits per second does the receiver receive if the data rate is 1 Mbps ? (A) 10 bps (B) 100 bps (C) 1000 bps (D) 10000 bps

Description : In a digital transmission, the receiver clock is 0.1 percent faster than the sender clock. How many extra bits per second does the receiver receive if the data rate is 1 Mbps ? (A) 10 bps (B) 100 bps (C) 1000 bps (D) 10000 bps

Last Answer : (C) 1000 bps 

A 4-bit synchronous counter uses flip-flops with propagation delay times of 15 ns each. The maximum possible time required for change of state will be (A) 15 ns. (B) 30 ns. (C) 45 ns. (D) 60 ns.

Description : A 4-bit synchronous counter uses flip-flops with propagation delay times of 15 ns each. The maximum possible time required for change of state will be (A) 15 ns. (B) 30 ns. (C) 45 ns. (D) 60 ns.

Last Answer : Ans: A 15 ns because in synchronous counter all the flip-flops change state at the same time.

Determine the maximum length of the cable (in km) for transmitting data at a rate of 500 Mbps in an Ethernet LAN with frames of size 10,000 bits. Assume the signal speed in the cable to be 2,00,000 km/s.b. 2 c. 2.5 d. 5

Description : Determine the maximum length of the cable (in km) for transmitting data at a rate of 500 Mbps in an Ethernet LAN with frames of size 10,000 bits. Assume the signal speed in the cable to be 2,00,000 km/s. b. 2 c. 2.5 d. 5

Last Answer : b. 2

What is the propagation delay when a signal is transmitter by an earth station to a geosynchronous satellite about 38,500 km above earth’s equator and then received by the same earth station? A. 256 msec B. 128 msec C. 300 msec D. 400 msec

Description : What is the propagation delay when a signal is transmitter by an earth station to a geosynchronous satellite about 38,500 km above earth’s equator and then received by the same earth station? A. 256 msec B. 128 msec C. 300 msec D. 400 msec

Last Answer : A. 256 msec

The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms

Description : The round-trip propagation delay between two earth stations through a geosynchronous satellite is A. 500 to 600 ms B. 300 to 400 ms C. 600 to 700 ms D. 400 to 500 ms

Last Answer : A. 500 to 600 ms

An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Description : An eight stage ripple counter uses a flip-flop with propagation delay of 75 nanoseconds. The pulse width of the strobe is 50ns. The frequency of the input signal which can be used for proper operation of the counter is approximately (A) 1 MHz. (B) 500 MHz. (C) 2 MHz. (D) 4 MHz.

Last Answer : Maximum time taken for all flip-flops to stabilize is 75ns x 8 + 50 = 650ns. Frequency of operation must be less than 1/650ns = 1.5 MHz.

was the first step in the evolution of Ethernet from a coaxial cable bus to hub managed, twisted pair network. a. Star LAN b. Ring LAN c. Mesh LAN d. All of the above

Description : was the first step in the evolution of Ethernet from a coaxial cable bus to hub managed, twisted pair network. a. Star LAN b. Ring LAN c. Mesh LAN d. All of the above

Last Answer : a. Star LAN

In OSI network architecture, the dialogue control and token management are responsibility of a. session layer b. network layer c. transport layer d. data link layer e. none of above

Description : In OSI network architecture, the dialogue control and token management are responsibility of a. session layer b. network layer c. transport layer d. data link layer e. none of above

Last Answer : session layer

Find out the OSI layer, which performs token management. A) Network Layer B) Transport Layer C) Session Layer D) Presentation Layer

Description : Find out the OSI layer, which performs token management. A) Network Layer B) Transport Layer C) Session Layer D) Presentation Layer

Last Answer : C) Session Layer

In OSI network architecture, the dialogue control and token management are responsibility of a. session layer b. network layer c. transport layer d. data link layer

Description : In OSI network architecture, the dialogue control and token management are responsibility of a. session layer b. network layer c. transport layer d. data link layer

Last Answer : a. session layer

A metro train 200 metres long takes 12 seconds to cross a man walking at 10 km/hr in a opposite to that of the train. Find the speed of the train? A) 50 km/hr B) 60km/hr C) 130km/hr D) 140km/hr

Description : A metro train 200 metres long takes 12 seconds to cross a man walking at 10 km/hr in a opposite to that of the train. Find the speed of the train? A) 50 km/hr B) 60km/hr C) 130km/hr D) 140km/hr

Last Answer : ANSWER: A Explanation:  Length of the train = 200 m  Man walking speed = 10 km/hr  Let the speed of the train be x' km/hr  Speed of the train relative to man = (x +10) km/hr  Convert km/hr into m/s   ... = 60(x +10)  3600 = 60x +600  60x = 3000 X = 50  So speed of the train is 110km/hr.

Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is ............... (A) 400 bps (B) 800 bps (C) 1600 bps (D) 3200 bps

Description : Four channels are multiplexed using TDM. If each channel sends 100 bytes/second and we multiplex 1 byte per channel, then the bit rate for the link is ............... (A) 400 bps (B) 800 bps (C) 1600 bps (D) 3200 bps

Last Answer : (D) 3200 bps Answer: D Explanation: The multiplexer is shown in the Figure. Each frame carries 1 byte from each channel; the size of each frame, therefore, is 4 bytes, or 32 bits. Because each ... channel, the frame rate must be 100 frames per second. The bit rate is 100 32 = 3200 bps. 

What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

Description : What do you call the phenomenon in digital circuits that describe the duration of time a digital signal passes a circuit? A. Transmission time B. Elapsed time C. Propagation delay D. Travel delay

Last Answer : C. Propagation delay

How many 8-bit characters can be transmitted per second over a 9600 baud serial communication link using asynchronous mode of transmission with one start bit, eight data bits, two stop bits, and one parity bit ? a. 600 b. 800 c. 876 d. 1200

Description : How many 8-bit characters can be transmitted per second over a 9600 baud serial communication link using asynchronous mode of transmission with one start bit, eight data bits, two stop bits, and one parity bit ? a. 600 b. 800 c. 876 d. 1200

Last Answer : b. 800