What is considered the most efficient mode in terms of energy transfer in waveguides? A. Dominant mode B. Normal mode C. Conventional mode D. Vertical mode

What is considered the most efficient mode in terms of energy transfer in waveguides?
A. Dominant mode
B. Normal mode
C. Conventional mode
D. Vertical mode
by

1 Answer

Answer :

A. Dominant mode
by

Related questions

Best reason for pressurizing waveguides with dry air A. To maintain propagation B. To maintain temperature of the waveguide C. To reduce the possibility of internal arcing D. To increase the speed of propagation

Description : Best reason for pressurizing waveguides with dry air A. To maintain propagation B. To maintain temperature of the waveguide C. To reduce the possibility of internal arcing D. To increase the speed of propagation

Last Answer : C. To reduce the possibility of internal arcing

Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In small columns, local efficiency is larger than Murphree efficiency; in large columns local efficiency is smaller than Murphree efficiency (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s (D) The concentration and hydrodynamic boundary layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Description : Pick out the wrong statement. (A) In the McCabe-Thiele diagram for binary distillation, vertical feed line represents saturated liquid feed and horizontal feed line represents saturated vapour feed (B) In ... layers over a flat plate are of equal thickness, if Schmidt number is equal to unity

Last Answer : (C) For Laminar flow over a plate of length L, the local mass transfer co￾efficient at a distance L from the leading edge is 1.5 × 10 -2m/s. Then the average mass transfer co-efficient for the plate is 2 × 10 -2m/s

Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation (B) Film co-efficient for vaporisation decreases as a result of vapor binding (C) In industrial practice, sub-cooling of condensate is required, when thecondensate is a volatile liquid and is to be transferred for storage(D) Overall heat transfer co-efficient in a heat exchanger is controlled by thevalue of the film co-efficient, which is higher

Description : Pick out the wrong statement. (A) The condensing film co-efficient is about 3 times lower for vertical condenser as compared to the equivalent horizontal condenser for identical situation ( ... in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Last Answer : (D) Overall heat transfer co-efficient in a heat exchanger is controlled by the value of the film co-efficient, which is higher

Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient for the cooling water, whether on shell side or tube side is the same. The best arrangement is (A) Vertical heat exchanger with steam on tube side (B) Vertical heat exchanger with steam on shell side (C) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Description : Steam is to be condensed in a shell and tube heat exchanger, 5 m long with a shell diameter of 1 m. Cooling water is to be used for removing the heat. Heat transfer co-efficient ... ) Horizontal heat exchanger with steam on tube side (D) Horizontal heat exchanger with steam on shell side

Last Answer : (B) Vertical heat exchanger with steam on shell side

In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Description : In case of vertical tube evaporator, with increase in liquor level, the overall heat transfer co-efficient (A) Increases (B) Decreases (C) Is not affected (D) May increase or decrease; depends on the feed

Last Answer : (B) Decreases

Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger calculations (Δt) weighted is used in place of Δt, when it involves more than one sequence of heating or cooling i.e., desuperheating & condensation or condensation & sub-cooling (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted (D) In case of short tube vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Description : Pick out the wrong statement. (A) 'Solvates' are chemical compounds formed by solute with their solvents. When water is the solvent, then it is called a 'hydrate' (B) In heat exchanger ... vertical evaporators, area of central downtake is about 50 to 100% of the total tube cross-sectional area

Last Answer : (C) Heat transfer co-efficient during nucleate boiling is not influenced by the agitation imparted

What is the term used to describe a spread spectrum communications system where the center frequency if a conventional carrier is altered many time per second in accordance with a pseudo-random list of channels? A. Frequency hopping B. Direct sequence C. Time-domain frequency modulation D. Frequency compandored spread spectrum

Description : What is the term used to describe a spread spectrum communications system where the center frequency if a conventional carrier is altered many time per second in accordance with a pseudo ... hopping B. Direct sequence C. Time-domain frequency modulation D. Frequency compandored spread spectrum

Last Answer : A. Frequency hopping

What kind of receiver is used in conventional telephone handset? A. Capacitor B. Electromagnetic C. Carbon D. Ceramic

Description : What kind of receiver is used in conventional telephone handset? A. Capacitor B. Electromagnetic C. Carbon D. Ceramic

Last Answer : B. Electromagnetic

What are the most fuel efficient vehicles including both hybrid and/or conventional trucks and cars?

Description : What are the most fuel efficient vehicles including both hybrid and/or conventional trucks and cars?

Last Answer : Overall, smaller more compact cars will have better fuel efficiency than larger heavier SUV's. While the average mileage of a compact hybrid is close to 40MPG, average SUV MPG is closer to 20.

Maximum viscosity of tar/PCM/fuel oil for easy and efficient atomisation in conventional burner is __________ centistokes (or 100 Redwood I seconds). (A) 5 (B) 25 (C) 50 (D) 100

Description : Maximum viscosity of tar/PCM/fuel oil for easy and efficient atomisation in conventional burner is __________ centistokes (or 100 Redwood I seconds). (A) 5 (B) 25 (C) 50 (D) 100

Last Answer : (B) 25

13) Esso retains outright ownership of all members of its distribution channel. Esso's channel would be best described as a ________ VMS. A)corporate B)contractual C)conventional D)administered E)vertical

Description : 13) Esso retains outright ownership of all members of its distribution channel. Esso's channel would be best described as a ________ VMS. A)corporate B)contractual C)conventional D)administered E)vertical

Last Answer : A)corporate

12) Decor Ltd, which makes, markets, and retails paint and home decorating products in a co -ordinated channel, is an example of (the) a: A)administered vertical marketing system. B)conventional marketing channel. C)channel network. D)use of power brokers in a channel framework. E)corporate vertical marketing system.

Description : 12) Decor Ltd, which makes, markets, and retails paint and home decorating products in a co-ordinated channel, is an example of (the) a: A)administered vertical marketing system. B) ... )channel network. D)use of power brokers in a channel framework. E)corporate vertical marketing system.

Last Answer : E)corporate vertical marketing system.

When Benetton, the sportswear designer and manufacturer, decided to open its own specialty shops to sell its merchandise, the firm was engaging in A)channel repetition . B)vertical channel integration. C)a conventional marketing channel. D)horizontal channel integration. E)channel expansion.

Description : When Benetton, the sportswear designer and manufacturer, decided to open its own specialty shops to sell its merchandise, the firm was engaging in A)channel repetition B)vertical channel integration. C)a conventional marketing channel. D)horizontal channel integration. E)channel expansion.

Last Answer : B)vertical channel integration.

A man and a woman, who do not show any apparent signs of a certain inherited disease, have seven children (2 daughters and 5 sons). Three of the sons suffer from the given disease but none of the daughters affected. Which of the following mode of inheritance do you suggest for this disease? (a) Sex-linked dominant (b) Sex-linked recessive (c) Sex-limited recessive (d) Autosomal dominant

Description : A man and a woman, who do not show any apparent signs of a certain inherited disease, have seven children (2 daughters and 5 sons). Three of the sons suffer from the given disease but none ... ? (a) Sex-linked dominant (b) Sex-linked recessive (c) Sex-limited recessive (d) Autosomal dominant

Last Answer : (b) Sex-linked recessive

Draw the field pattern of circular waveguide for its dominant mode.

Description : Draw the field pattern of circular waveguide for its dominant mode.

Last Answer : TE1,1 Mode is the dominant mode in circular waveguides. In TEm,n/ TMm,nthe letter m denotes the number of full-wave intensity variations around the circumference and n represents the number of half-wave ... changes radially out from the center to the wall. (Cylindrical co-ordinates are used).

The dominant mode in cylindrical waveguide

Description : The dominant mode in cylindrical waveguide

Last Answer : The dominant mode in cylindrical waveguide TE11

A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is

Description : A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is

Last Answer : A rectangular waveguide is 5.1 cm by 2.4 cm (inside dimension). The cut off frequency of the dominant mode is 2.94 GHz

When a dominant mode wave guide not terminated in its characteristic impedance is excited with a 10 GHZ

Description : When a dominant mode wave guide not terminated in its characteristic impedance is excited with a 10 GHZ signal then if d is the distance between two successive minima of the standing wave in the guide then   (A) d = 1.5 cm (B) d is less then 1.5 cm (C) d is greater then 1.5 cm (D) d = 3 cm

Last Answer : When a dominant mode wave guide not terminated in its characteristic impedance is excited with a 10 GHZ signal then if d is the distance between two successive minima of the standing wave in the guide then d = 1.5 cm

A rectangular waveguide is 4.2 cm by 1.85 cm. The cut-off frequency of the dominant mode through this

Description : A rectangular waveguide is 4.2 cm by 1.85 cm. The cut-off frequency of the dominant mode through this waveguide is  (a) 3.57 GHz (b) 3.75 GHz (c) 3.70 MHz (d) 3.57 MHz

Last Answer : A rectangular waveguide is 4.2 cm by 1.85 cm. The cut-off frequency of the dominant mode through this waveguide is  3.57 GHz 

In a circular waveguide the dominant mode is:

Description : In a circular waveguide the dominant mode is:  (1) TE01 (2) TE11 (3) TE20 (4) TE21

Last Answer : . In a circular waveguide the dominant mode is: TE11.

A matched termination in which the electromagnetic energy is absorbed by water. A. Maximum power transfer B. Load C. Load water D. Basin

Description : A matched termination in which the electromagnetic energy is absorbed by water. A. Maximum power transfer B. Load C. Load water D. Basin

Last Answer : C. Load water

Which type of Mendelian inherited condition results in both genders being affected equally in a vertical pattern? a) Automosomal dominant inheritance An individual who has an autosomal dominant inherited condition carries a gene mutation for that condition on one chromosome of a pair. b) Automosomal recessive inheritance The pattern of inheritance in autosomal recessive inherited conditions is different from that of autosomal dominant inherited conditions in that it is more horizontal than vertical, with relatives of a single generation tending to have the condition. c) X-linked inheritance X-linked conditions may be inherited in families in recessive or dominant patterns.

Description : Which type of Mendelian inherited condition results in both genders being affected equally in a vertical pattern? a) Automosomal dominant inheritance An individual who has an autosomal dominant ... that combine during early embryonic development leading to incomplete closure of the neural tube.

Last Answer : a) Automosomal dominant inheritance An individual who has an autosomal dominant inherited condition carries a gene mutation for that condition on one chromosome of a pair.

The velocity of a wave travelling in the air medium without transmission lines or waveguides(wireless) is a) 6 x 10 8 b) 3 x 10 8 c) 1.5 x 10 8 d) 9 x 10 8

Description : The velocity of a wave travelling in the air medium without transmission lines or waveguides(wireless) is a) 6 x 10 8 b) 3 x 10 8 c) 1.5 x 10 8 d) 9 x 10 8

Last Answer : b) 3 x 10 8

In waveguides, which of the following conditions will be true? a) V > c b) V < c c) V = c d) V >> c

Description : In waveguides, which of the following conditions will be true? a) V > c b) V < c c) V = c d) V >> c

Last Answer : a) V > c

Curl cannot be employed in which one of the following? a) Directional coupler b) Magic Tee c) Isolator and Terminator d) Waveguides

Description : Curl cannot be employed in which one of the following? a) Directional coupler b) Magic Tee c) Isolator and Terminator d) Waveguides

Last Answer : d) Waveguides

Spherical systems are employed in waveguides. State True/False a) True b) False

Description : Spherical systems are employed in waveguides. State True/False a) True b) False

Last Answer : b) False

Rectangular waveguides dominate the circular waveguides. Find the reason. a) Low cut-off frequency b) Easy to design c) More wave propagation d) The statement is false

Description : Rectangular waveguides dominate the circular waveguides. Find the reason. a) Low cut-off frequency b) Easy to design c) More wave propagation d) The statement is false

Last Answer : b) Easy to design

Cylindrical system is employed in waveguides. State True/False. a) True b) False

Description : Cylindrical system is employed in waveguides. State True/False. a) True b) False

Last Answer : a) True

The number of half-wave patterns in the "b" dimension of rectangular waveguides is indicated by which of the two descriptive subscripts?

Description : The number of half-wave patterns in the "b" dimension of rectangular waveguides is indicated by which of the two descriptive subscripts?

Last Answer : Second.

The field arrangements in waveguides are divided into what two categories to describe the various modes of operation?

Description : The field arrangements in waveguides are divided into what two categories to describe the various modes of operation?

Last Answer : Transverse electric (TE) and transverse magnetic (TM).

What term is used to identify each of the many field configurations that can exist in waveguides?

Description : What term is used to identify each of the many field configurations that can exist in waveguides?

Last Answer : Mode of operation.

Compared to the velocity of propagation of waves in air, what is the velocity of propagation of waves in waveguides?

Description : Compared to the velocity of propagation of waves in air, what is the velocity of propagation of waves in waveguides?

Last Answer : Slower.

What is the primary lower-frequency limitation of waveguides?

Description : What is the primary lower-frequency limitation of waveguides?

Last Answer : Physical size.

What is used as a dielectric in waveguides?

Description : What is used as a dielectric in waveguides?

Last Answer : Air.

What kind of material must be used in the construction of waveguides?

Description : What kind of material must be used in the construction of waveguides?

Last Answer : Conductive material.

List the two common types of waveguides in use today.

Description : List the two common types of waveguides in use today.

Last Answer : Cylindrical and rectangular.

What mechanisms in the fiber waveguides weaken and distort the optical signal?

Description : What mechanisms in the fiber waveguides weaken and distort the optical signal?

Last Answer : Scattering, absorption, and dispersion.

Which type of fiber-optic cable is the best for very high speed data? a. Single-mode step-index b. Multimode step-index c. Single-mode graded-index d. Multimode graded-index

Description : Which type of fiber-optic cable is the best for very high speed data? a. Single-mode step-index b. Multimode step-index c. Single-mode graded-index d. Multimode graded-index

Last Answer : a. Single-mode step-index

Which type of fiber optic cable is most widely used? a. Single-mode step-index b. Multimode step-index c. Single-mode graded-index d. Multimode graded-index

Description : Which type of fiber optic cable is most widely used? a. Single-mode step-index b. Multimode step-index c. Single-mode graded-index d. Multimode graded-index

Last Answer : a. Single-mode step-index

Which of the following is not a common type of fiber-optic cable? a. Single-mode step-index b. Multimode graded-index c. Single-mode graded-index d. Multimode step-index

Description : Which of the following is not a common type of fiber-optic cable? a. Single-mode step-index b. Multimode graded-index c. Single-mode graded-index d. Multimode step-index

Last Answer : c. Single-mode graded-index

What type of fiber has the highest modal dispersion? a. Step-index multimode b. Graded index multimode c. Step-index single mode d. Graded index mode

Description : What type of fiber has the highest modal dispersion? a. Step-index multimode b. Graded index multimode c. Step-index single mode d. Graded index mode

Last Answer : a. Step-index multimode

What is the insertion loss of connector-type splices for a single mode fiber optics? a. 0.51dB b. 0.31dB c. 0.49dB d. 0.38dB

Description : What is the insertion loss of connector-type splices for a single mode fiber optics? a. 0.51dB b. 0.31dB c. 0.49dB d. 0.38dB

Last Answer : d. 0.38dB

What is a specific path the light takes in an optical fiber corresponding to a certain angle and number of reflection a. Mode b. Grade c. Numerical Aperture d. Dispersion

Description : What is a specific path the light takes in an optical fiber corresponding to a certain angle and number of reflection a. Mode b. Grade c. Numerical Aperture d. Dispersion

Last Answer : a. Mode

How many sidebands are present in the J3E mode? A. Two sidebands and a carrier B. One upper sideband C. One lower sideband D. Two carriers and one sideband

Description : How many sidebands are present in the J3E mode? A. Two sidebands and a carrier B. One upper sideband C. One lower sideband D. Two carriers and one sideband

Last Answer : B. One upper sideband

What is the insertion loss of connector type splices for a single mode optical fiber? A. 0.51 dB B. 0.49 dB C. 0.31 dB D. 0.38 db

Description : What is the insertion loss of connector type splices for a single mode optical fiber? A. 0.51 dB B. 0.49 dB C. 0.31 dB D. 0.38 db

Last Answer : D. 0.38 db

One of the following is among the types of fiber optics used in electronics communication. A. Step-index multimode B. Graded-index multimode C. Semi-graded multimode D. Single mode

Description : One of the following is among the types of fiber optics used in electronics communication. A. Step-index multimode B. Graded-index multimode C. Semi-graded multimode D. Single mode

Last Answer : C. Semi-graded multimode

Determine from the following the basic mode of transmission system in the public data network in which data are transferred from the source to the network and from the network to the destination in the frame format. A. Voice mode B. Asynchronous mode C. Synchronous mode D. Packet mode

Description : Determine from the following the basic mode of transmission system in the public data network in which data are transferred from the source to the network and from the network to the destination in the frame format. A. Voice mode B. Asynchronous mode C. Synchronous mode D. Packet mode

Last Answer : D. Packet mode

Propagation mode of microwave in a waveguide is known as _______. A. TM B. TE C. SW D. TEM

Description : Propagation mode of microwave in a waveguide is known as _______. A. TM B. TE C. SW D. TEM

Last Answer : B. TE

Type of fiber that has the highest modal dispersion A. Step-index multimode B. Step-index single mode C. Graded index mode D. Graded index multimode

Description : Type of fiber that has the highest modal dispersion A. Step-index multimode B. Step-index single mode C. Graded index mode D. Graded index multimode

Last Answer : A. Step-index multimode

Insertion loss of connector-type splices for a single-mode fiber cable. A. 0.2 dB B. 0.3 dB C. 0.09 dB D. 0.38 dB

Description : Insertion loss of connector-type splices for a single-mode fiber cable. A. 0.2 dB B. 0.3 dB C. 0.09 dB D. 0.38 dB

Last Answer : D. 0.38 dB