______ sets the limit on the maximum capacity of a channel with a given noise level. A. Hartley theorem B. Shannon-hartley theorem C. Nyquist theorem D. Shannon theorem

______ sets the limit on the maximum capacity of a channel with a given noise level.
A. Hartley theorem
B. Shannon-hartley theorem
C. Nyquist theorem
D. Shannon theorem
by

1 Answer

Answer :

B. Shannon-hartley theorem
by

Related questions

What theorem sets a limit on the maximum capacity of a channel with a given noise level? A. Nyquist theorem B. Hartley law C. Shannon-Hartley theorem D. Shannon theorem

Description : What theorem sets a limit on the maximum capacity of a channel with a given noise level? A. Nyquist theorem B. Hartley law C. Shannon-Hartley theorem D. Shannon theorem

Last Answer : C. Shannon-Hartley theorem

________ sets a limit on the maximum capacity of a channel with a give noise level. A. Hartley theorem B. Shannon-Hartley theorem C. Nyquist theorem D. Shannon theorem

Description : ________ sets a limit on the maximum capacity of a channel with a give noise level. A. Hartley theorem B. Shannon-Hartley theorem C. Nyquist theorem D. Shannon theorem

Last Answer : B. Shannon-Hartley theorem

State the Shannon Hartley’s theorem for channel capacity. Explain the effect of S/N ratio and bandwidth on channel capacity.

Description : State the Shannon Hartley’s theorem for channel capacity. Explain the effect of S/N ratio and bandwidth on channel capacity.

Last Answer : In information theory, the Shannon-Hartley theorem tells the maximum rate at which information can be transmitted over a communications channel of a specified bandwidth in the presence of noise. According to Shannon, ... value of S/N with increase in B,assuming the signal power S to be constant.

For a ______ channel, we need to use the Shannon capacity tofind the maximum bit rate. A) noisy B) noiseless C) bandpass D) low-pass

Description : For a ______ channel, we need to use the Shannon capacity tofind the maximum bit rate. A) noisy B) noiseless C) bandpass D) low-pass

Last Answer : noisy

ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Description : ECE Board Exam March 1996 According to the Nyquist theorem, the sampling rate that can be used in a PCM system is ________ the highest audio frequency. A. once B. eight times C. twice D. thrice

Last Answer : C. twice

For a ______ channel, the Nyquist bit rate formula defines thetheoretical maximum bit rate. A) noisy B) noiseless C) bandpass D) low-pass

Description : For a ______ channel, the Nyquist bit rate formula defines thetheoretical maximum bit rate. A) noisy B) noiseless C) bandpass D) low-pass

Last Answer : noiseless

The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Description : The stability of transmitted signal from a simple Hartley oscillator single transmitter which is coupled to and antenna wire affected by ______. A. Chirping of oscillator B. Closer coupling between the oscillator and the antenna. C. Location of antenna D. Material of antenna

Last Answer : B. Closer coupling between the oscillator and the antenna.

Which does not effect noise in a channel? A. None of these B. Bandwidth C. Temperature D. Quantizing level

Description : Which does not effect noise in a channel? A. None of these B. Bandwidth C. Temperature D. Quantizing level

Last Answer : D. Quantizing level

You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Description : You are measuring noise in a voice channel at 7 dB test point level. The meter reads -56 dBm (FIA weighted). What is the reading in dBrnc? A. 20 B. 32 C. 35 D. 25

Last Answer : C. 35

In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Description : In measuring noise in a voice channel at a 4 dB test point level, the meter reads -70 dBm (F1A weighted), convert the reading to pWp. A. 53 B. 93 C. 63 D. 83

Last Answer : B. 93

The Nyquist theorem specifies the minimum samplingrate to be_______. A) equal to the lowest frequency of asignal B) equal to the highest frequency ofa signal C) twice thebandwidth of a signal D) twice thehighest frequencyof a signal

Description : The Nyquist theorem specifies the minimum samplingrate to be_______. A) equal to the lowest frequency of asignal B) equal to the highest frequency ofa signal C) twice thebandwidth of a signal D) twice thehighest frequencyof a signal

Last Answer : twice thehighest frequencyof a signal

If the frequency spectrum of a signal has a bandwidth of500 Hz with thehighest frequency at 600 Hz, what shouldbe the samplingrate, according to the Nyquist theorem? A) 200 samples/s B) 500 samples/s C) 1000 samples/s D) 1200 samples/s

Description : If the frequency spectrum of a signal has a bandwidth of500 Hz with thehighest frequency at 600 Hz, what shouldbe the samplingrate, according to the Nyquist theorem? A) 200 samples/s B) 500 samples/s C) 1000 samples/s D) 1200 samples/s

Last Answer : 1200 samples/s

Classify data networks. Explain with the help of Nyquist theorem, the data rate limitations in PSTN’s. Give an account of modems used in data transfer. Explain their importance and list some of the V-series recommendations.

Description : Classify data networks. Explain with the help of Nyquist theorem, the data rate limitations in PSTN’s. Give an account of modems used in data transfer. Explain their importance and list some of the V-series recommendations.

Last Answer : Classifications of Data Network:  Data Networks are classified according to their geographical coverage: Wide area networks (WANs) Metropolitan area networks(MANs) Local area ...  V.53 Limits for the maintenance of telephone type circuits used for data transmission. 

State sampling theorem. Define Nyquist rate.

Description : State sampling theorem. Define Nyquist rate.

Last Answer : SAMPLING THEOREM: Sampling theorem states that a band-limited signal of finite energy having the highest frequency component fm Hz can be represented and recovered completely from a set of samples taken ... frequency should be equal to or greater than twice the maximum signal frequency (fs≥ 2fm)

One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the high power output. The purpose of which is to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Description : One of the following is a high powered RF ac basic transmitter that has two or more stages, the oscillator stage which determines the frequency opereation and RF amplifier stage orstages that develop the ... to develop a good frequency stability. A. Goldsmith B. MOPA C. Alexanderson D. Hartley

Last Answer : B. MOPA

State Hartley’s law and Shannon Hartley’s theorem.

Description : State Hartley’s law and Shannon Hartley’s theorem. 

Last Answer : Hartley's law The amount of information that can be sent in a given transmission is dependent on the bandwidth of communication channel and the duration of transmission.  OR  Hartley's theorem state ... Where, B = Channel Bandwidth S = Signal Power N = Noise within the channel bandwidth

Which theory states that the light wave behaves as if it consists of many tiny particles? a. Huygen’s theory b. Wave theory of light c. Nyquist theory d. Quantum theory

Description : Which theory states that the light wave behaves as if it consists of many tiny particles? a. Huygen’s theory b. Wave theory of light c. Nyquist theory d. Quantum theory

Last Answer : d. Quantum theory

Which of the following is not a way of minimizing if not eliminating noise? A. Use redundancy B. Increase transmitted power C. Reduce signaling rate D. Increase channel bandwidth

Description : Which of the following is not a way of minimizing if not eliminating noise? A. Use redundancy B. Increase transmitted power C. Reduce signaling rate D. Increase channel bandwidth

Last Answer : D. Increase channel bandwidth

Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Description : Reference noise is ___________. A. a 1000 Hz, -90 dBm tone B. a noise that creates the same interfering effect as a 1000Hz, -90dBm tone C. a noise that creates zero dBrn in a voice channel D. B and C above

Last Answer : D. B and C above

You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Description : You are measuring noise in a voice channel with a Lenkurt 601A, F1A weighting network and a flat meter. Your meter reads -47dBm. What is this reading in dBa? A. 77 dBa B. 35 dBa C. 38 dBa D. 32 dBa

Last Answer : C. 38 dBa

Noise always affects the signal in a communications systems at the ________. A. transmitter B. channel C. information source D. destination

Description : Noise always affects the signal in a communications systems at the ________. A. transmitter B. channel C. information source D. destination

Last Answer : B. channel

An interfering current in a telegraph or signaling channel due to telegraph or signaling current by another channel. A. Crosstalk B. Noise current C. Crossfire D. Intermodulation

Description : An interfering current in a telegraph or signaling channel due to telegraph or signaling current by another channel. A. Crosstalk B. Noise current C. Crossfire D. Intermodulation

Last Answer : C. Crossfire

What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Description : What is the effect in over modulated amplitude modulated radio broadcasting transmission? A. Interference to adjacent channel B. Higher fidelity C. Increase noise D. Higher audio signal

Last Answer : A. Interference to adjacent channel

What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Description : What does the noise weighting curve shows? A. Noise signals measured with a 144 handset B. Power levels of noise found in carrier systems C. The interfering effect of other frequencies in a voice ... a reference frequency of one kilohertz D. Interfering effects of signals compared with a 3-kHz tone

Last Answer : C. The interfering effect of other frequencies in a voice channel compared with a reference frequency of one kilohertz

The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Description : The signal in a channel is measured to be 23 dB while noise in the same channel is measured to be 9 dB. The signal to noise ratio therefore is __________. A. 9/23 B. 23/9 C. 32 dB D. 14 dB

Last Answer : D. 14 dB

The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity

Description : The total noise power present in a 1-Hz bandwidth . A. Noise density B. Noise figure C. Noise limit D. Noise intensity

Last Answer : A. Noise density

For a loudness level between 110 and 120 dB, the maximum daily exposure limit is ____ minute (s). A. 1 B. 60 C. 20 D. 45

Description : For a loudness level between 110 and 120 dB, the maximum daily exposure limit is ____ minute (s). A. 1 B. 60 C. 20 D. 45

Last Answer : A. 1

Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Description : Assume a frequency range of 405.0125 MHz to 405.0875 MHz and 25 kHz channeling plan, determine the center frequency of the second channel from the lower limit. A. 405.030 MHz B. 405.025 MHz C. 405.050 MHz D. 405.075 MHz

Last Answer : C. 405.050 MHz

Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Description : Assume a frequency range of 401.000 MHz to 401.050 MHz, if you apply 25 kHz channeling plan, determine the center frequency of the first channel from the lower limit. A. 401.010 MHz B. 401.0125 MHz C. 401.025 MHz D. 401.00625 MHz

Last Answer : B. 401.0125 MHz

If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz

Description : If frequency range of 401.000MHz to 401.050MHz has to be channelized at 12.5 kHz between channel, what is the center of its first channel from the lower limit? A. 401.125MHz B. 401.00625MHz C. 401.025MHz D. 401.0125MHz

Last Answer : B. 401.00625MHz

As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel

Description : As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel which is bandlimited to ‘B’ Hz. The number of samples ‘n’ is given by (symbols/notations carry their usual meaning) A) B/T B) T/B C) 2BT D) BT/2 

Last Answer : As per Shannon’s channel capacity theorem, if samples are transmitted in ‘T’ seconds over a noisy channel which is bandlimited to ‘B’ Hz. The number of samples ‘n’ is given by ( ... /notations carry their usual meaning) A) B/T B) T/B C) 2BT D) BT/2 

What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Description : What bandwidth is needed to support a capacity of 128 kbps when the signal power to noise power ratio in decibels is 100? A. 19224 Hz B. 3853 Hz C. 19244 Hz D. 3583 Hz

Last Answer : B. 3853 Hz

______ is a term in the test language for noise testing in telephone circuits that means a one-syllable word consisting of a consonant, a vowel, and another consonant. A. Logatom B. Nosfer C. Ore D. Belcore

Description : ______ is a term in the test language for noise testing in telephone circuits that means a one-syllable word consisting of a consonant, a vowel, and another consonant. A. Logatom B. Nosfer C. Ore D. Belcore

Last Answer : A. Logatom

What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Description : What is meant by the term modulation index? A. The processor index. B. The ratio between the deviation of a frequency modulated signal and the modulating frequency. C. The FM signal-to-noise ratio. D. The ratio of the maximum carrier frequency deviation to the highest audio modulating frequency.

Last Answer : B. The ratio between the deviation of a frequency modulated signal and the modulating frequency.

What is the reference level for noise measurement, F1A weighted? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Description : What is the reference level for noise measurement, F1A weighted? A. -90 dBm B. -82 dBm C. -67 dBm D. -85 dBm

Last Answer : D. -85 dBm

You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Description : You are measuring noise at a -6 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -59 dBm. This is _________ dBa0. A. 24 B. 12 C. 23 D. 32

Last Answer : D. 32

You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Description : You are measuring noise at a +3 dB level point, using the Lenkurt 601A, F1A weighting network, and a flat meter. The meter reading is -57dBm. This is ________dBa0. A. 20 B. 15 C. 25 D. 17

Last Answer : C. 25

What is the reference noise level? A. 10 pW B. 0 dBm C. 1mW D. -90 dBm

Description : What is the reference noise level? A. 10 pW B. 0 dBm C. 1mW D. -90 dBm

Last Answer : D. -90 dBm

Atmospheric noise is less at severe frequencies above A. Audio level B. 30 MHz C. 10 GHz D. 1 GHz

Description : Atmospheric noise is less at severe frequencies above A. Audio level B. 30 MHz C. 10 GHz D. 1 GHz

Last Answer : B. 30 MHz

The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the same bandwidth. A. Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Description : The ratio of the level of the modulated output of a transmitter under conditions of standard test modulation to the level of the demodulated output with no modulation applied both measured with the ... . Reference audio output B. None of these C. Audio frequency response D. Residual noise level

Last Answer : D. Residual noise level

ECE Board Exam March 1996 What is the purpose of the receiver’s squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent fluctuations in the AGC bias level C. To reduce the receiver’s sensitivity to all incoming signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Description : ECE Board Exam March 1996 What is the purpose of the receiver's squelch circuit? A. To overcome fluctuations in the level the RF signal arriving at the receiver antenna B. To prevent ... signals D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

Last Answer : D. To prevent amplified noise from reaching the loudspeaker during the absence of an incoming signal

You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Description : You are measuring a voice channel at a -4 dB test point level, the meter reads -73 dBm (pure test tone) convert the reading in dBmCO. A. 16 B. 18 C. 22 D. 12

Last Answer : C. 22

Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1.0MHz and the temperature is 20˚C, and that the receiver is connected to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Description : Calculate the noise figure of the receiver whose RF amplifier has an input resistance of 1000Ω and an equivalent shot-noise resistance of 2000Ω, a gain of 25 and load resistance of 125 kΩ. Given that the bandwidth is 1. ... to an antenna with an impedance of 75Ω. A. 30.3 B. 3.03 C. 303 D. .303

Last Answer : A. 30.3

The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling

Description : The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling rate will be: (1) 1/100 (2) 1/200 (3) 1/300 (4) 1/600 

Last Answer : The analog signal m(t) is given below m(t) = 4 cos 100 pt + 8 sin 200 pt + cos 300 pt, the Nyquist sampling rate will be: 1/300

A method of multiple accessing where a given RF channel bandwidth is divided inot smaller frequency band. A. CDMA B. ANIK-D C. TDMA D. FDMA

Description : A method of multiple accessing where a given RF channel bandwidth is divided inot smaller frequency band. A. CDMA B. ANIK-D C. TDMA D. FDMA

Last Answer : D. FDMA

In the European standard, the aurial transmitter maximum radiated power is ______ of peak visual transmitter power. A. 10% B. 30% C. 20% D. 40%

Description : In the European standard, the aurial transmitter maximum radiated power is ______ of peak visual transmitter power. A. 10% B. 30% C. 20% D. 40%

Last Answer : C. 20%

Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Description : Your Western Electric 3A test set meter reading is -23 dBm at at test point level of -8 dB. This is ______ dBrnc0. A. 75 B. 29 C. 30 D. 31

Last Answer : A. 75

Which coaxial cable connector is least expensive and is widely used for TV sets,VCRs and cable TV? A. N-type connector B. F-type connector C. BNC D. PL-259

Description : Which coaxial cable connector is least expensive and is widely used for TV sets,VCRs and cable TV? A. N-type connector B. F-type connector C. BNC D. PL-259

Last Answer : B. F-type connector

What is the maximum noise limit in a panel house during the day?

Description : I live in a panel house and my neighbors are threatening me with the police

Last Answer : http://www.akusticka-pena.cz/novinky/hygienicke-limity-hluku/ you can read everything here

Maximum permissible limit of noise as per "Noise Pollution Rules 2000 of India" is:

Description : Maximum permissible limit of noise as per "Noise Pollution Rules 2000 of India" is:

Last Answer : Maximum permissible limit of noise as per "Noise Pollution Rules 2000 of India" is: A. 60 decibles B. 70 decibels C. 80 decibels D. 100 decibels.