In four stroke engine there is one power stroke in _____ of crankshaft rotation. a. 180° b. 360° c. 540° d. 720° (Ans:d)

In four stroke engine there is one power stroke in _____ of crankshaft rotation. a. 180° b. 360° c. 540° d. 720° (Ans:d)
by

1 Answer

Answer :

The ascending order of strokes in four stroke engine is a. Suction stroke – Expansion stroke – Compression stroke – Exhaust stroke b. Suction stroke – Compression stroke – Expansion stroke –Exhaust stroke c. Suction stroke – Expansion stroke – Exhaust stroke – Compression stroke d. Suction stroke – Compression stroke – Exhaust stroke – Expansion stroke (Ans:b)
by
selected by

Related questions

In two stroke engine one power occurs in _______ of crank rotation A. 180° B. 360° C. 270° D. 720°

Description : In two stroke engine one power occurs in _______ of crank rotation A. 180° B. 360° C. 270° D. 720°

Last Answer : ANSWER : B

In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air consumption, brake power and incylinder pressure. Tutorials on engine performance parameters. Heat balance sheet. Engine performance curves. 1. The increase in intake air temperature into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Description : In four stroke engine which of the following is also known as power stroke a. Suction stroke b. Compression stroke c. Expansion stroke d. Exhaust stroke (Ans:c) Measurements of fuel and air ... into IC engine,___________its efficiency A. increase B. decrease C. does not alter D. unpredictable on

Last Answer : ANSWER : B

In two stroke engine, which of the following functions are performed at the same time? a. Compression and exhaust b. Intake and Expansion c. Intake and exhaust d. Intake and compression (Ans:c)

Description : In two stroke engine, which of the following functions are performed at the same time? a. Compression and exhaust b. Intake and Expansion c. Intake and exhaust d. Intake and compression (Ans:c)

Last Answer : The compression ratio in a Compression Ignition (CI) engine is generally in between a. 8 to 13 b. 14 to 23 c. 20 to 28 d. 25 to 32 (Ans:b)

A two stroke engine has a speed of 750 rpm. A four stroke engine having an identical cylinder size runs at 1500 rpm. The theoretical output of the two stroke engine will (a) Be twice that of the four stroke engine (b) Be half that of the four stroke engine (c) Be the same as that of the four stoke (d) Depend upon whether it is a CI or SI engine

Description : A two stroke engine has a speed of 750 rpm. A four stroke engine having an identical cylinder size runs at 1500 rpm. The theoretical output of the two stroke engine will (a) Be twice that of the four stroke ... ) Be the same as that of the four stoke (d) Depend upon whether it is a CI or SI engine

Last Answer : Ans :c

Which of the following engine can work on very lean mixture a. Spark ignition engine b. compression ignition engine c. two stroke engine d. Four stroke engine

Description : Which of the following engine can work on very lean mixture a. Spark ignition engine b. compression ignition engine c. two stroke engine d. Four stroke engine

Last Answer : ANSWER b. compression ignition engine

hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Description : hen displacement volume is divided by piston displacement, what will we obtained (a) number of cylinders (b) number of power stroke per minute for all cylinders (c) number of revolution of the crankshaft (engine) (d) number of revolution of crankshaft × number of cylinder

Last Answer : (b) number of power stroke per minute for all cylinders

Choke in a I.C. engine is used to control a) Camshaft speed b) Specific fuel consumption c) Air fuel mixture d) Crankshaft speed Ans. c

Description : Choke in a I.C. engine is used to control a) Camshaft speed b) Specific fuel consumption c) Air fuel mixture d) Crankshaft speed Ans. c

Last Answer : ans c

For same power output and same r, as compared to 2- stroke engines, four stroke SI engines have (a) Higher fuel consumption (b) Lower thermal efficiency (c) Highest exhaust temperatures (d) Higher thermal efficiency

Description : For same power output and same r, as compared to 2- stroke engines, four stroke SI engines have (a) Higher fuel consumption (b) Lower thermal efficiency (c) Highest exhaust temperatures (d) Higher thermal efficiency

Last Answer : Ans :d

The actual volume of fresh charge admitted in 4-stroke petrol engine is A. equal to stroke volume B. equal stroke volume and clearance volume C. less than stroke volume D. more than stroke volume

Description : The actual volume of fresh charge admitted in 4-stroke petrol engine is A. equal to stroke volume B. equal stroke volume and clearance volume C. less than stroke volume D. more than stroke volume

Last Answer : ANSWER : C

Morse test is conducted on the engine to calculate the mechanical efficiency of A. single cylinder CI engine B. single cylinder SI engine C. only on two stroke engines D. multi cylinder engine

Description : Morse test is conducted on the engine to calculate the mechanical efficiency of A. single cylinder CI engine B. single cylinder SI engine C. only on two stroke engines D. multi cylinder engine

Last Answer : ANSWER : D

In a typical medium speed 4- stroke Diesel engine, the inlet valve A. opens 20°before top dead centre and closes at 35°afterthebottomdead centre. B. opens up at top dead centre and closes at bottomdead centre C. may open orcloseanywhere D. remains open for 200°

Description : In a typical medium speed 4- stroke Diesel engine, the inlet valve A. opens 20°before top dead centre and closes at 35°afterthebottomdead centre. B. opens up at top dead centre and closes at bottomdead centre C. may open orcloseanywhere D. remains open for 200°

Last Answer : ANSWER : A

A gas engine has a volume of 300 cc and clearance volume of 25 cc. Its volumetric efficiency is 0.8 and mech efficiency is 0.9. What is the volume of the mixture taken in per stroke? (a) 248 cc (b) 252 cc (c) 264 cc (d) 286 cc

Description : A gas engine has a volume of 300 cc and clearance volume of 25 cc. Its volumetric efficiency is 0.8 and mech efficiency is 0.9. What is the volume of the mixture taken in per stroke? (a) 248 cc (b) 252 cc (c) 264 cc (d) 286 cc

Last Answer : Ans : c

For low load operation more economical engine is a. petrol engine b. diesel engine c. muticylinder engine d. two stroke engine

Description : For low load operation more economical engine is a. petrol engine b. diesel engine c. muticylinder engine d. two stroke engine

Last Answer : ANSWER b. diesel engine

The term scavenging is generally associated with a. 2-stroke engine b. 4-stroke engine c. high efficiency engine d. diesel engine

Description : The term scavenging is generally associated with a. 2-stroke engine b. 4-stroke engine c. high efficiency engine d. diesel engine

Last Answer : ANSWER C. high efficiency engine

An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per cycle is 1800 kJ/kg, then work output per cycle per kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Description : An engine working on air standard Otto cycle has a cylinder diameter of 10 cm and stroke length of 15 cm. The ratio of specific heats for air is 1.4. If the clearance volume is 196.3 cc and the heat supplied per kg of air per ... kg of air is a. 879.1 kJ/ b. 890.2 kJ c. 895.3 kJ d. 973.5 kJ

Last Answer : ANSWER d. 973.5 kJ

Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Description : Scavenging air in diesel engine means a. air used for combustion under pressure b. forced air for cooling the cylinder c. burnt air containing products of combustion d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

Last Answer : ANSWER d. air used for forcing burnt gases out of the engines cylinder during the exhaust stroke

In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)

Description : In compression ignition (CI) engine, the compression ratio is a. Cylinder volume / Clearance volume b. Swept Volume / Cylinder Volume c. Clearance volume / Cylinder volume d. Cylinder volume / Swept volume (Ans:a)

Last Answer : In two stroke engine there is one power stroke in _____ of crankshaft rotation. a. 90° b. 180° c. 270° d. 360° (Ans:d)

Heat engine uses ______ energy to produce mechanical work. a. Thermal b. Fluid c. Kinetic d. Electric (Ans:a)

Description : Heat engine uses ______ energy to produce mechanical work. a. Thermal b. Fluid c. Kinetic d. Electric (Ans:a)

Last Answer : Which of the following is not an internal Combustion (IC) engine? a. Gas engine b. Wankel engine c. Jet engine d. Stirling engine (Ans:d)

The compression ratio in a Spark Ignition (SI) engine is generally in between a. 7 to 10 b. 10 to 14 c. 14 to 18 d. 18 to 22 (Ans:a)

Description : The compression ratio in a Spark Ignition (SI) engine is generally in between a. 7 to 10 b. 10 to 14 c. 14 to 18 d. 18 to 22 (Ans:a)

Last Answer : Which of the following is not true for two stroke engine as compared to four stroke engine? a. Less cooling is required b. Greater lubrication is required c. More uniform torque on crankshaft d. Complete exhaust of products of combustion (Ans:a)

The _____________ sensor, senses rotation of engine camshaft for speed and timing of injection. a) throttle position b) manifold pressure c) camshaft position d) knock

Description : The _____________ sensor, senses rotation of engine camshaft for speed and timing of injection. a) throttle position b) manifold pressure c) camshaft position d) knock

Last Answer : Answer: c Explanation: The camshaft position sensor, senses rotation of engine camshaft for speed and timing of injection whereas the throttle position sensor, senses the movement of the throttle ... engine intake manifold so that the mixture strength can be adjusted with changes in engine load.

The degree measure of Prime Meridian is - (1) 90° (2) 180° (3) 0° (4) 360°

Description : The degree measure of Prime Meridian is - (1) 90° (2) 180° (3) 0° (4) 360°

Last Answer : (3) 0° Explanation: A prime meridian is a meridian (a line of longitude) in a geographic coordinate system at which longitude is de fined to be 0°.

What will be the phase angle relationship of a six-pole, three-phase, rotating field generator? A. 60° B. 120° C. 180° D. 360°

Description : What will be the phase angle relationship of a six-pole, three-phase, rotating field generator? A. 60° B. 120° C. 180° D. 360°

Last Answer : Answer: B

In case of partial bearing, the angle of contact of the bushing with the journal is (A) 270° (B) More than 180° (C) Less than 180° (D) 360°

Description : In case of partial bearing, the angle of contact of the bushing with the journal is (A) 270° (B) More than 180° (C) Less than 180° (D) 360°

Last Answer : (C) Less than 180°

In case of full journal bearing, the angle of contact of the bushing with the journal is (A) 60° (B) 90° (C) 180° (D) 360°

Description : In case of full journal bearing, the angle of contact of the bushing with the journal is (A) 60° (B) 90° (C) 180° (D) 360°

Last Answer : (D) 360°

In case of partial bearing, the angle of contact of the bushing with the journal is usually (A) 120° (B) 180° (C) 45° (D) 360°

Description : In case of partial bearing, the angle of contact of the bushing with the journal is usually (A) 120° (B) 180° (C) 45° (D) 360°

Last Answer : (A) 120°

Number of degree a complete circle represents is A. 90° B. 180° C. 270° D. 360°

Description : Number of degree a complete circle represents is A. 90° B. 180° C. 270° D. 360°

Last Answer : 360°

Phase difference between a node and an antinode is A. 90° B. 45° C. 180° D. 360°

Description : Phase difference between a node and an antinode is A. 90° B. 45° C. 180° D. 360°

Last Answer : 180°

If isolation factor is negative, then what is the phase difference between transmitted and disturbing force? a) 180° b) 90° c) 450° d) 360°

Description : If isolation factor is negative, then what is the phase difference between transmitted and disturbing force? a) 180° b) 90° c) 450° d) 360°

Last Answer : a) 180°

A traverse deflection angle is (A) Less than 90° (B) More than 90° but less than 180° (C) The difference between the included angle and 180° (D) The difference between 360° and the included angle

Description : A traverse deflection angle is  (A) Less than 90°  (B) More than 90° but less than 180°  (C) The difference between the included angle and 180°  (D) The difference between 360° and the included angle 

Last Answer : (C) The difference between the included angle and 180° 

If deflection angles are measured in a closed traverse, the difference between the sum of the right-hand and that of the left hand angles should be equal to (A) 0° (B) 90° (C) 180° (D) 360°

Description : If deflection angles are measured in a closed traverse, the difference between the sum of the right-hand and that of the left hand angles should be equal to (A) 0° (B) 90° (C) 180° (D) 360°

Last Answer : (D) 360°

Back bearing of a line is equal to (A) Fore bearing ± 90° (B) Fore bearing ± 180° (C) Fore bearing ± 360° (D) Fore bearing ± 270°

Description : Back bearing of a line is equal to (A) Fore bearing ± 90° (B) Fore bearing ± 180° (C) Fore bearing ± 360° (D) Fore bearing ± 270°

Last Answer : (B) Fore bearing ± 180°

What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Description : What is the phase relationship of the signal at the collector of Q2 to the signal at the collector of Q, A) 0° B) 90° C) 180° D) 360°.

Last Answer : C) 180°

In a single acting reciprocating compressor, the suction, compression and delivery of air takes place in A. One stroke B. Two stroke C. Three stroke D. Four stroke

Description : In a single acting reciprocating compressor, the suction, compression and delivery of air takes place in A. One stroke B. Two stroke C. Three stroke D. Four stroke

Last Answer : ANSWER : B

The relation between Indicated power (ip), Friction power (fp) and Brake power (bp) is a. ip = fp – bp b. ip = fp + bp c. bp = ip + fp d. bp = ip / fp (Ans:b)

Description : The relation between Indicated power (ip), Friction power (fp) and Brake power (bp) is a. ip = fp – bp b. ip = fp + bp c. bp = ip + fp d. bp = ip / fp (Ans:b)

Last Answer : Which of the following is not true for internal combustion engine as compare to external combustion engine? a. It has lower ratio of weight to output b. They are self starting c. Higher overall efficiency d. Mechanical simplicity (Ans:b)

Whenthecrankshaft of 4-stroke running at 1500 rpm thecamshaftwillrun at A. 3000 rpm B. 6000 rpm C. 1500 rpm D. 750 rpm

Description : Whenthecrankshaft of 4-stroke running at 1500 rpm thecamshaftwillrun at A. 3000 rpm B. 6000 rpm C. 1500 rpm D. 750 rpm

Last Answer : ANSWER : D

Fuel is injected into the cylinder at the end of ______________ stroke. a) suction b) compression c) expansion d) exhaust

Description : Fuel is injected into the cylinder at the end of ______________ stroke. a) suction b) compression c) expansion d) exhaust

Last Answer : Answer: b Explanation: Fuel is injected into the cylinder at the end of compression stroke and not at suction or expansion stroke.

The ratio of work done per cycle to the stroke volume of the compressor is known as A. Compressor capacity B. Compression ratio C. Compressor efficiency D. Mean effective pressure

Description : The ratio of work done per cycle to the stroke volume of the compressor is known as A. Compressor capacity B. Compression ratio C. Compressor efficiency D. Mean effective pressure

Last Answer : ANSWER : D

Piston speed is equal to a. stroke x rpm b. (stroke x rpm) / 2 c. 2 x stroke x rpm d. 4 x stroke x rpm

Description : Piston speed is equal to a. stroke x rpm b. (stroke x rpm) / 2 c. 2 x stroke x rpm d. 4 x stroke x rpm

Last Answer : ANSWER c. 2 x stroke x rpm

The energy of expanding gas is transferred by piston to connecting rod through a. Crank pin b. Gudgeon pin c. Bearing d. Crankcase (Ans:b)

Description : The energy of expanding gas is transferred by piston to connecting rod through a. Crank pin b. Gudgeon pin c. Bearing d. Crankcase (Ans:b)

Last Answer : Which of the following is not used in four stroke compression-ignition (CI) engines? a. Fuel pump b. Spark plug c. Fuel injector d. Inlet and outlet Valves (Ans:b)

Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Description : Rated speed of an engine is the speed at which an engine devlopes (A) Maximum crankshaft torque (B) Maximum brake horse power output (C) Maximum thermal efficiency (D) Maximum drawback pull

Last Answer : (B) Maximum brake horse power output

Give reason: The wheel makes another half rotation after the expansion stroke of steam engine.

Description : Give reason: The wheel makes another half rotation after the expansion stroke of steam engine.

Last Answer : Due to inertia of the crankshaft, the wheel makes another half rotation and completes one cycle.

The reason for supercharging in any engine is to be A. increase efficiency B. increase power C. effect fuel economy D. reduce weight and bulk for a given output

Description : The reason for supercharging in any engine is to be A. increase efficiency B. increase power C. effect fuel economy D. reduce weight and bulk for a given output

Last Answer : ANSWER : D

By supercharging the power output of an engine is expected to increase by A. 20% B. 45% C. 75% D. 50%

Description : By supercharging the power output of an engine is expected to increase by A. 20% B. 45% C. 75% D. 50%

Last Answer : ANSWER : A

Supercharging of an IC engine is done so that the A. thermal efficiency increases B. power output increases C. speed of the engine increases D. power output decreases

Description : Supercharging of an IC engine is done so that the A. thermal efficiency increases B. power output increases C. speed of the engine increases D. power output decreases

Last Answer : ANSWER : B

A 40 kW engine has a mechanical efficiency of 80 %. If the frictional power is assumed to be constant with load, what is the approximate value of the mechanical efficiency at 50 % of the rated load? (a) 45% (b) 55 % (c) 65% (d) 75%

Description : A 40 kW engine has a mechanical efficiency of 80 %. If the frictional power is assumed to be constant with load, what is the approximate value of the mechanical efficiency at 50 % of the rated load? (a) 45% (b) 55 % (c) 65% (d) 75%

Last Answer : Ans :c

An engine produces 10 kW brake power while working with a brake thermal efficiency of 30%. If the calorific value of the fuel used is 40000 kJ/kg, then what is the fuel consumption? (a) 1.5 kg/hour (b) 3 kg/hour (c) 0.3 kg/hour (d) 1 kg/hour

Description : An engine produces 10 kW brake power while working with a brake thermal efficiency of 30%. If the calorific value of the fuel used is 40000 kJ/kg, then what is the fuel consumption? (a) 1.5 kg/hour (b) 3 kg/hour (c) 0.3 kg/hour (d) 1 kg/hour

Last Answer : Ans :b

If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Description : If the performance of diesel engine of different sizes, cylinder dimensions and power rating are to be compared, which of the following parameters can be used for such comparison? (a) Swept volume (b) Air fuel ratio (c) Specific brake fuel consumption (d) Volumetric efficiency

Last Answer : Ans :c

In a morse test for a 2 cylinder, 2 S SI engine, the brake power was 9 kW. Whereas the brake power of individual cylinders with spark cut off were 4.25 kW and 3.75 kW. The mecheffic of the engine is (a) 90% (b) 80% (c) 45.5% (d) 52.5%

Description : In a morse test for a 2 cylinder, 2 S SI engine, the brake power was 9 kW. Whereas the brake power of individual cylinders with spark cut off were 4.25 kW and 3.75 kW. The mecheffic of the engine is (a) 90% (b) 80% (c) 45.5% (d) 52.5%

Last Answer : Ans :a

In a variable speed SI engine, the maximum torque occurs at the maximum (a) Speed (b) Brake power (c) Indicated power (d) Volumetric efficiency

Description : In a variable speed SI engine, the maximum torque occurs at the maximum (a) Speed (b) Brake power (c) Indicated power (d) Volumetric efficiency

Last Answer : Ans :d

The method of determination of indicated power of multi cylinder SI engine is by use of (a) Morse test (b) Prony brake test (c) Motoring test (d) Heat balance test

Description : The method of determination of indicated power of multi cylinder SI engine is by use of (a) Morse test (b) Prony brake test (c) Motoring test (d) Heat balance test

Last Answer : Ans : a