Can you weld galvanized metal to steel?

Can you weld galvanized metal to steel?
by

1 Answer

Answer :

When using SMAW ("stick") welding, galvanized steel can be welded in the same manner as uncoated steel. ... The thicker the zinc coating, the more fumes are generated, and those fumes have to be able to escape easily into the atmosphere and not be forced through the liquid weld metal.
by
selected by

Related questions

How much does galvanized steel wire cost per foot?

Description : How much does galvanized steel wire cost per foot?

Last Answer : Depending on the grade of steel that you want, the cost can be anywhere from $0.25 per foot, to approximately $18.00 per foot. These costs of course depend on the strength of the ... such as holding suspension bridges together. The lowere end steel cables are generally strong enough to tow cars.

Is galvanized steel wire better for fences then non-galvanized steel wire?

Description : Is galvanized steel wire better for fences then non-galvanized steel wire?

Last Answer : There's really no such thing as a steel wire fence without galvanising. An ungalvanized steel wire fence would rust the first time it rained. Therefore you'd rather have galvanized steel or another ... process coats the steel with a zinc coating, making it rust-resistant in the presence of moisture.

Earth wire or ground wire is made of: a) copper b) aluminium c) iron d) galvanized steel

Description : Earth wire or ground wire is made of: a) copper b) aluminium c) iron d) galvanized steel

Last Answer : Ans: D

Zrezne galvanized sheet metal?

Description : When I have an outdoor railing galvanized, will it rust over time? Or is it resistant to rust?

Last Answer : Of course I do. the sheet metal is rusty, but a good surface treatment (paint) will extend its life.

A galvanometer is an instrument used to measure ___________. A. thickness of galvanized metal B. resistance of electrical wiring insulation C. very small amounts of current or voltage D. quantity of galvans in an electric circuit

Description : A galvanometer is an instrument used to measure ___________. A. thickness of galvanized metal B. resistance of electrical wiring insulation C. very small amounts of current or voltage D. quantity of galvans in an electric circuit

Last Answer : Answer: C

Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc

Description : Cold cracking in the heat affected zone of a high strength steel weld can take place because of the (A) Retained austenite (B) Martensite formation (C) Relatively high sulphur content in the base metal (D) Sufficient hydrogen present in the welding arc

Last Answer : (B) Martensite formation

Do you think the stunning outcome of the 2016 election will get the non-voters and 3rd party voters galvanized into reality next year?

Description : Do you think the stunning outcome of the 2016 election will get the non-voters and 3rd party voters galvanized into reality next year?

Last Answer : The most trolliest of trolling questions I have seen in some time here. Come on.

My brother has galvanized my friends to launch a Spanish Inquisition into my life!

Description : My brother has galvanized my friends to launch a Spanish Inquisition into my life!

Last Answer : You just have to write to him and tell him that he needs to butt out of your life. If you want to preserve the relationship, you can explain as you did here why you are doing it, but if you just want him not to interfere, you can just say that.

I have a question about hot dip galvanizing. Is there any effect on galvanized coating if flux (zinc ammonium chloride salt) mixed inside hydrochloric acid tank instead of the normal separate hydrochloric acid tank and flux tank?

Description : I have a question about hot dip galvanizing. Is there any effect on galvanized coating if flux (zinc ammonium chloride salt) mixed inside hydrochloric acid tank instead of the normal separate hydrochloric acid tank and flux tank?

Last Answer : They should be applied separately, the acid and flux are weakening each other mixed together like that. Although they perform two separate functions in the process, both functions are necessary and are being weakened by mixing the two chemicals. You may have problems with the plating flaking off.

Galvanized iron has a thin coating of : -General Knowledge

Description : Galvanized iron has a thin coating of : -General Knowledge

Last Answer : Zinc is the coating

Zrezne galvanized iron?

Description : Does the galvanized railing still have to be painted or will it not rust on its own with galvanizing?

Last Answer : Galvanized iron must be allowed to oxidize, otherwise the paint would not adhere to it at all. It depends on the strength of the zinc layer, but it is definitely better to paint with a suitable color. ... It creates a thin film that does not peel off, but must be renewed from time to time :)

Galvanized Gutters Installation?

Description : Galvanized Gutters Installation?

Last Answer : form_title=Galvanized Gutters Installation form_header=8753 Describe the particular gutter style you would like*= () "Standard (square edge) () Standard (""Ogee""-decorative detail) () Half round () Oversized ... in your home.*= {Select One,One story,Two stories,Three stories,Four stories or more}

Which element is associated with the term "galvanized"? w) gallium x) zinc y) mercury z) nickel

Description : Which element is associated with the term "galvanized"? w) gallium x) zinc y) mercury z) nickel

Last Answer : ANSWER: X -- ZINC

Galvanized containers are not used for storage of food. Give reason.

Description : Galvanized containers are not used for storage of food. Give reason.

Last Answer : Galvanized containers (zinc coated) cannot be used for preparing and storing food stuff, which are acidic in nature because zinc gets dissolved in dilute acids in food forming poisonous zinc compounds which will poison the content.

Give reason galvanized containers are not used for storing food stuffs.

Description : Give reason galvanized containers are not used for storing food stuffs.

Last Answer : Galvanized container contains zinc coating. Since Zn is more active metal it readily reacts with the acids present in the food stuffs forming Zn compounds which are highly poisonous & it may poison the food stuffs. Therefore galvanized containers can not be used for storing food stuff.

What examines the inside of a weld in a steel oil pipe?

Description : What examines the inside of a weld in a steel oil pipe?

Last Answer : Need answer

welding i want to weld steel bars to my trailer should i use a arch welder or a wire feed welder?

Description : welding i want to weld steel bars to my trailer should i use a arch welder or a wire feed welder?

Last Answer : arch welding is a more stable form of welding. it get hotter and creates a stronger bond

Why You Shouldn’t Weld Carbon Steel and Stainless Steel Wire Together?

Description : Why You Shouldn’t Weld Carbon Steel and Stainless Steel Wire Together?

Last Answer : Reasons You Want to Avoid Welding Stainless Steel to Carbon Steel1.Difficulty: Combining dissimilar metals together, such as welding stainless steel to carbon steel, adds extra challenges to ... aren’t perfect.3.Thermal Expansion in High Temperature Service Conditions: Another problem with usi

Weld decay can be minimized by specifying steel with: a) Higher carbon level b) higher chromium level c) lower carbon level d) lower chromium level

Description : Weld decay can be minimized by specifying steel with: a) Higher carbon level b) higher chromium level c) lower carbon level d) lower chromium level

Last Answer : c) lower carbon level

Weld decay occurs in which of the following steel types? a) Carbon/Manganese b) Low alloy c) Any stainless steel d) Austenitic stainless steels

Description : Weld decay occurs in which of the following steel types? a) Carbon/Manganese b) Low alloy c) Any stainless steel d) Austenitic stainless steels

Last Answer : d) Austenitic stainless steels

A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC+ve polarity, and a ROL:of 180mm per min. What would be the arc energy? a) Insufficient information given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Description : A butt weld has been made by MMA in a 50mm thick impact tested steel plate. The welding electrode used was a basic type, 5mm diameter. The measured welding parameters for one of the runs was 250 amps, 24 volts, using DC ... given to calculate the arc energy b) 1.9 kJ/mm c) 1.87 kJ/mm d) 2.0 kJ/mm

Last Answer : d) 2.0 kJ/mm

When making a vertical weld and it appears that the weld metal is going to drip over the shelf what should you do?

Description : When making a vertical weld and it appears that the weld metal is going to drip over the shelf what should you do?

Last Answer : Feel Free to Answer

In a transverse WELD tensile test, if the break was in the weld metal, the sample would he: a) Rejected b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate c) Retested d) Acceptable if the UTS is between 80 - 90% of the specified UTS of the plate

Description : In a transverse WELD tensile test, if the break was in the weld metal, the sample would he: a) Rejected b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate c) Retested d) Acceptable if the UTS is between 80 - 90% of the specified UTS of the plate

Last Answer : b) Acceptable if the UTS is equal to or greater than the specified UTS of the plate

Why is it essential to clean the excess weld metal on completion of the production weld? a) So it can be ready for painting b) To remove any rust c) To ensure it is suitably clean for visual inspection and NDT d) To remove slag from the undercut

Description : Why is it essential to clean the excess weld metal on completion of the production weld? a) So it can be ready for painting b) To remove any rust c) To ensure it is suitably clean for visual inspection and NDT d) To remove slag from the undercut

Last Answer : c) To ensure it is suitably clean for visual inspection and NDT

Why would visual inspection of the excess weld metal at the bottom of a cross country pipeline be important? a) It is the most difficult area to weld b) It is the dirtiest part of the pipe as it is near the ground c) Welders always forget to weld the bottom d) It is the most difficult area to radiograph

Description : Why would visual inspection of the excess weld metal at the bottom of a cross country pipeline be important? a) It is the most difficult area to weld b) It is the dirtiest part of the pipe as ... ground c) Welders always forget to weld the bottom d) It is the most difficult area to radiograph

Last Answer : a) It is the most difficult area to weld

Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and 40,000 psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.

Description : Ratings for welding neck flanges under ASME B16.5 are based upon which of the following? a) The flange thickness and 40,000 psi yield strength. b) The hub thickness at the welding end and ... psi yield strength. c) The weld metal yield strength. d) The piping wall thickness and yield strength.

Last Answer : b) The hub thickness at the welding end and 40,000 psi yield strength

Main advantage of 3-piece P F Mould is? (i) To overcome fin defect.* (ii) To prevent the flaw of molten metal (iii) To make proper weld size (iv) None to the above

Description : Main advantage of 3-piece P F Mould is? (i) To overcome fin defect.* (ii) To prevent the flaw of molten metal (iii) To make proper weld size (iv) None to the above

Last Answer : (i) To overcome fin defect.*

After AT Welding First train is to be passed after ? (i) 20 Minutes from pouring of weld metal. (ii) 35 Minutes from pouring of weld metal. (iii) 30 Minutes from pouring of weld metal.* (iv) 25 Minutes from pouring of weld metal.

Description : After AT Welding First train is to be passed after ? (i) 20 Minutes from pouring of weld metal. (ii) 35 Minutes from pouring of weld metal. (iii) 30 Minutes from pouring of weld metal.* (iv) 25 Minutes from pouring of weld metal.

Last Answer : (iii) 30 Minutes from pouring of weld metal.*

Is it possible to weld paring knives to barbed wire?

Description : Is it possible to weld paring knives to barbed wire?

Last Answer : answer:If the knife blades are steel, then yes. Sounds like a cool project.

Will my JB-Weld be wrecked?

Description : Will my JB-Weld be wrecked?

Last Answer : JB Weld is an epoxy and cross contamination of the two parts is not a deal breaker here. Just clean off the cap as best as you can and put a little WD 40 on the threads to help prevent the cap from getting stuck. The product should be fine…if not PM me and I can help.

Does anybody know anything about Body Weld at Toyota Plant?

Description : Does anybody know anything about Body Weld at Toyota Plant?

Last Answer : http://findarticles.com/p/articles/mi_m3012/is_10_182/ai_94335240/

Is it possible to weld cast iron?

Description : I need to join two cast iron pieces, can the cast iron be welded?

Last Answer : Everything goes. # (# hi) http://www.mmspektrum.com/clanek/svarovani-a-opravy-litinovych-vyrobku.html

Is it possible to weld without electricity?

Description : I need to weld something but I don't have electricity in the cottage. It will work?

Last Answer : autogen? (tuxedo)

Is it possible to weld cast iron?

Description : Do you think it would work?

Last Answer : Definitely weldable. http://www.welco.cz/katalog/seda-litina-obalene-elektrody

do i need an actual welding table in order to be able to weld?

Description : do i need an actual welding table in order to be able to weld?

Last Answer : Need Answer

What is the meaning of the different symbols and abbreviations found on the documents that they use (such as surface finish to be achieved linear and geometric tolerances electronic components weld s?

Description : What is the meaning of the different symbols and abbreviations found on the documents that they use (such as surface finish to be achieved linear and geometric tolerances electronic components weld s?

Last Answer : Need answer

Why should convex weld faces be avoided?

Description : Why should convex weld faces be avoided?

Last Answer : What is the answer ?

How On thin gauge metals sensitive to atmosphere contamination a backing bar is used to protect the root side of the weld?

Description : How On thin gauge metals sensitive to atmosphere contamination a backing bar is used to protect the root side of the weld?

Last Answer : What is the answer ?

What is the Weld penetration formula?

Description : What is the Weld penetration formula?

Last Answer : What is the answer ?

What types of classes do I need to take in order to learn to weld?

Description : What types of classes do I need to take in order to learn to weld?

Last Answer : You can learn how to weld by a basic do-it-yourself book on the subject, or taking a workshop class. If you are in high school, there are not really any set classes for welding.

When installing the banks exhaust system will I need to weld it?

Description : When installing the banks exhaust system will I need to weld it?

Last Answer : No this is untrue. There are plenty that you can by that are meant to be clamped together. Also make sure you follow the instructions because welding a kit that was meant to be clamped together will void the warranty.

What is the difference between slip and weld neck flange?

Description : What is the difference between slip and weld neck flange?

Last Answer : There are some difference between ANSI Stainless Steel Welding Neck Flange and ANSI Stainless Steel Slip On Flange:1. Welding forms are differernt. Welding Neck Flange can be radiographed but slip on flanges ... . Nominal pressure of slip on flange is 0.6-4MPa grade, compared with the butt weldin

Which of the following statement(s) is/are correct concerning cell junctions? a. The major occluding junction is the tight junction or zonula occludens b. Tight junctions are usually located near the basal pole of the cell c. Desmosomes are button-like points of attachment which serve to weld together adjacent cells d. Gap junctions are a type of cell junction specialized for cell communication

Description : Which of the following statement(s) is/are correct concerning cell junctions? a. The major occluding junction is the tight junction or zonula occludens b. Tight junctions are usually located near ... adjacent cells d. Gap junctions are a type of cell junction specialized for cell communication

Last Answer : Answer: a, c, d Cell junctions are classified as occluding, anchoring, and communicating. The major occluding junction is the tight junction or zonula occludens which connects ... gap junction which is specialized for communication. This junction mediates both electrical and chemical coupling

Post weld heat treatment is done by (A) Normalising (B) Stress relieving (C) Tempering (D) Solution annealing

Description : Post weld heat treatment is done by (A) Normalising (B) Stress relieving (C) Tempering (D) Solution annealing

Last Answer : (B) Stress relieving

Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Last Answer : b) False

A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Last Answer : b) False

Plug weld is a. Rectangular b. Square c. Triangular d. None

Description : Plug weld is a. Rectangular b. Square c. Triangular d. None

Last Answer : d. None

Fillet weld is a a. Square b. Rectangular c. Triangular d. None

Description : Fillet weld is a a. Square b. Rectangular c. Triangular d. None

Last Answer : c. Triangular

The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None

Description : The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None

Last Answer : c. 45 0

Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None

Description : Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None

Last Answer : b. 0.707x leg