Is it possible to weld without electricity?

I need to weld something but I don't have electricity in the cottage. It will work?
by

1 Answer

Answer :

autogen? (tuxedo)
by

Related questions

Is it possible to weld paring knives to barbed wire?

Description : Is it possible to weld paring knives to barbed wire?

Last Answer : answer:If the knife blades are steel, then yes. Sounds like a cool project.

Is it possible to weld cast iron?

Description : I need to join two cast iron pieces, can the cast iron be welded?

Last Answer : Everything goes. # (# hi) http://www.mmspektrum.com/clanek/svarovani-a-opravy-litinovych-vyrobku.html

Is it possible to weld cast iron?

Description : Do you think it would work?

Last Answer : Definitely weldable. http://www.welco.cz/katalog/seda-litina-obalene-elektrody

Till USFD testing of new AT weld what is criteria for joggling ? (i) Joggling with two far end bold (ii) Joggling with two tight clamps* (iii) Leave without joggling till its testing (iv) None of the above

Description : Till USFD testing of new AT weld what is criteria for joggling ? (i) Joggling with two far end bold (ii) Joggling with two tight clamps* (iii) Leave without joggling till its testing (iv) None of the above

Last Answer : (ii) Joggling with two tight clamps*

Will my JB-Weld be wrecked?

Description : Will my JB-Weld be wrecked?

Last Answer : JB Weld is an epoxy and cross contamination of the two parts is not a deal breaker here. Just clean off the cap as best as you can and put a little WD 40 on the threads to help prevent the cap from getting stuck. The product should be fine…if not PM me and I can help.

Does anybody know anything about Body Weld at Toyota Plant?

Description : Does anybody know anything about Body Weld at Toyota Plant?

Last Answer : http://findarticles.com/p/articles/mi_m3012/is_10_182/ai_94335240/

do i need an actual welding table in order to be able to weld?

Description : do i need an actual welding table in order to be able to weld?

Last Answer : Need Answer

What is the meaning of the different symbols and abbreviations found on the documents that they use (such as surface finish to be achieved linear and geometric tolerances electronic components weld s?

Description : What is the meaning of the different symbols and abbreviations found on the documents that they use (such as surface finish to be achieved linear and geometric tolerances electronic components weld s?

Last Answer : Need answer

When making a vertical weld and it appears that the weld metal is going to drip over the shelf what should you do?

Description : When making a vertical weld and it appears that the weld metal is going to drip over the shelf what should you do?

Last Answer : Feel Free to Answer

Why should convex weld faces be avoided?

Description : Why should convex weld faces be avoided?

Last Answer : What is the answer ?

How On thin gauge metals sensitive to atmosphere contamination a backing bar is used to protect the root side of the weld?

Description : How On thin gauge metals sensitive to atmosphere contamination a backing bar is used to protect the root side of the weld?

Last Answer : What is the answer ?

What is the Weld penetration formula?

Description : What is the Weld penetration formula?

Last Answer : What is the answer ?

What examines the inside of a weld in a steel oil pipe?

Description : What examines the inside of a weld in a steel oil pipe?

Last Answer : Need answer

What types of classes do I need to take in order to learn to weld?

Description : What types of classes do I need to take in order to learn to weld?

Last Answer : You can learn how to weld by a basic do-it-yourself book on the subject, or taking a workshop class. If you are in high school, there are not really any set classes for welding.

welding i want to weld steel bars to my trailer should i use a arch welder or a wire feed welder?

Description : welding i want to weld steel bars to my trailer should i use a arch welder or a wire feed welder?

Last Answer : arch welding is a more stable form of welding. it get hotter and creates a stronger bond

When installing the banks exhaust system will I need to weld it?

Description : When installing the banks exhaust system will I need to weld it?

Last Answer : No this is untrue. There are plenty that you can by that are meant to be clamped together. Also make sure you follow the instructions because welding a kit that was meant to be clamped together will void the warranty.

What is the difference between slip and weld neck flange?

Description : What is the difference between slip and weld neck flange?

Last Answer : There are some difference between ANSI Stainless Steel Welding Neck Flange and ANSI Stainless Steel Slip On Flange:1. Welding forms are differernt. Welding Neck Flange can be radiographed but slip on flanges ... . Nominal pressure of slip on flange is 0.6-4MPa grade, compared with the butt weldin

Why You Shouldn’t Weld Carbon Steel and Stainless Steel Wire Together?

Description : Why You Shouldn’t Weld Carbon Steel and Stainless Steel Wire Together?

Last Answer : Reasons You Want to Avoid Welding Stainless Steel to Carbon Steel1.Difficulty: Combining dissimilar metals together, such as welding stainless steel to carbon steel, adds extra challenges to ... aren’t perfect.3.Thermal Expansion in High Temperature Service Conditions: Another problem with usi

Can you weld galvanized metal to steel?

Description : Can you weld galvanized metal to steel?

Last Answer : When using SMAW ("stick") welding, galvanized steel can be welded in the same manner as uncoated steel. ... The thicker the zinc coating, the more fumes are generated, and those fumes have to be able to escape easily into the atmosphere and not be forced through the liquid weld metal.

Which of the following statement(s) is/are correct concerning cell junctions? a. The major occluding junction is the tight junction or zonula occludens b. Tight junctions are usually located near the basal pole of the cell c. Desmosomes are button-like points of attachment which serve to weld together adjacent cells d. Gap junctions are a type of cell junction specialized for cell communication

Description : Which of the following statement(s) is/are correct concerning cell junctions? a. The major occluding junction is the tight junction or zonula occludens b. Tight junctions are usually located near ... adjacent cells d. Gap junctions are a type of cell junction specialized for cell communication

Last Answer : Answer: a, c, d Cell junctions are classified as occluding, anchoring, and communicating. The major occluding junction is the tight junction or zonula occludens which connects ... gap junction which is specialized for communication. This junction mediates both electrical and chemical coupling

Post weld heat treatment is done by (A) Normalising (B) Stress relieving (C) Tempering (D) Solution annealing

Description : Post weld heat treatment is done by (A) Normalising (B) Stress relieving (C) Tempering (D) Solution annealing

Last Answer : (B) Stress relieving

Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Description : Transverse fillet weld can be designed using the same equations as of parallel fillet weld. a) True b) False

Last Answer : b) False

A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Description : A single transverse weld is preferred over double transverse fillet weld. a) True b) False

Last Answer : b) False

Plug weld is a. Rectangular b. Square c. Triangular d. None

Description : Plug weld is a. Rectangular b. Square c. Triangular d. None

Last Answer : d. None

Fillet weld is a a. Square b. Rectangular c. Triangular d. None

Description : Fillet weld is a a. Square b. Rectangular c. Triangular d. None

Last Answer : c. Triangular

The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None

Description : The angle of a fillet weld is a. 20 0 b. 40 0 c. 45 0 d. None

Last Answer : c. 45 0

Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None

Description : Length of throat of a fillet weld is a. 0.505 x leg b. 0.707x leg c. 0.909x leg d. None

Last Answer : b. 0.707x leg

Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None

Description : Area under tension in a single transverse fillet lap weld is (i)0.707 tl (ii) 0.807 tl (iii) 400 tl (iv)None

Last Answer : (i)0.707 tl

Quantity is not a part of the weld symbol (i)Dark circle (ii) Open circle (iii) Angle of weld (iv)Starting and stopping allowance for welding

Description : Quantity is not a part of the weld symbol (i)Dark circle (ii) Open circle (iii) Angle of weld (iv)Starting and stopping allowance for welding

Last Answer : (iv)Starting and stopping allowance for welding

Term which is not a part of the weld symbol (i) Tail (ii) Arrow (iii) Temperature of welding (iv) None

Description : Term which is not a part of the weld symbol (i) Tail (ii) Arrow (iii) Temperature of welding (iv) None

Last Answer : (iii) Temperature of welding

Quantity which is not a part of the weld symbol (i)Length of welding (ii) Weld is made in the welding shop (iii) Welding is on both sides (iv) Machine used in welding

Description : Quantity which is not a part of the weld symbol (i)Length of welding (ii) Weld is made in the welding shop (iii) Welding is on both sides (iv) Machine used in welding

Last Answer : (iv) Machine used in welding

Different parts of a weld symbol are (i) Arrow, center line and back part (ii) Arrow, body line and length (iii) Arrow, body line and tail (iv)None

Description : Different parts of a weld symbol are (i) Arrow, center line and back part (ii) Arrow, body line and length (iii) Arrow, body line and tail (iv)None

Last Answer : (iii) Arrow, body line and tail

A weld symbol is necessary because of (i) Aesthetic sense (ii) Finishing (iii) Manufacturing (iv) None

Description : A weld symbol is necessary because of (i) Aesthetic sense (ii) Finishing (iii) Manufacturing (iv) None

Last Answer : (iii) Manufacturing

Testing the ultimate strength of the weld falls in nondestructive examination. a) True b) False

Description : Testing the ultimate strength of the weld falls in nondestructive examination. a) True b) False

Last Answer : b) False

If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Description : If a circular shaft is welded to the plate by means of circumferential fillet, then the shaft is subjected to torsional moment M. If throat of weld is t, then torsional shear stress is given by a) M/2πtr2 b) M/πtr2 c) M/4πtr2 d) None of the listed

Last Answer : a) M/2πtr2

Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm. a) 230/t b) 360/t c) 200/t d) None of the listed

Description : Find the bending stress in the top weld is if thickness of weld is t. Given P=15kN and e=120mm. a) 230/t b) 360/t c) 200/t d) None of the listed

Last Answer : b) 360/t

Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False

Description : Strength of parallel fillet weld is greater than strength of transverse fillet weld. a) True b) False

Last Answer : b) False

If length of weld is l and leg h, then area of throat can be given by a) 0.707 hl b) 1.414hl c) hl d) None of the listed

Description : If length of weld is l and leg h, then area of throat can be given by a) 0.707 hl b) 1.414hl c) hl d) None of the listed

Last Answer : a) 0.707 hl

Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed

Description : Relation between throat and leg for a parallel fillet weld is a) t =h Cos (45’) b) h =t Cos (45’) c) h= t d) None of the listed

Last Answer : a) t =h Cos (45’)

The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Description : The length of each of the two equal sides of a parallel fillet weld is called a) Leg b) Throat c) Arm d) None of the listed

Last Answer : a) Leg

Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Description : Parallel fillet weld and transverse fillet weld both have the plane in which maximum shear stress occurs at 45’ to the leg dimension. a) True b) False

Last Answer : b) False

Convex weld is generally preferred over normal weld. a) True b) False

Description : Convex weld is generally preferred over normal weld. a) True b) False

Last Answer : b) False

If force act in a direction parallel to the direction of weld, then fillet weld is called as? a) Transverse b) Longitudinal c) Parallel d) Longitudinal or Parallel

Description : If force act in a direction parallel to the direction of weld, then fillet weld is called as? a) Transverse b) Longitudinal c) Parallel d) Longitudinal or Parallel

Last Answer : d) Longitudinal or Parallel

Hard peening is a) Hammering the weld across the length while the joint is hot b) Hammering the weld along the length while the joint is hot c) Hammering the weld along the length while the joint is cold d) Hammering the weld across the length while the joint is cold

Description : Hard peening is a) Hammering the weld across the length while the joint is hot b) Hammering the weld along the length while the joint is hot c) Hammering the weld along the length while the joint is cold d) Hammering the weld across the length while the joint is cold

Last Answer : b) Hammering the weld along the length while the joint is hot

A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.

Description : A backing ring is used inside the pipe joint when making a (a) butt weld (b) fillet weld (c) sleeve weld (d) socket weld (e) tube weld.

Last Answer : (a) butt weld

A fillet weld is an approximately triangular cross section joining two surfaces lying parallels to each other. a) True b) False

Description : A fillet weld is an approximately triangular cross section joining two surfaces lying parallels to each other. a) True b) False

Last Answer : b) False

For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at (a) 22.5° (b) 30° (c) 45° (d) 60°

Description : For a parallel load on a fillet weld of equal legs, the plane of maximum shear occurs at (a) 22.5° (b) 30° (c) 45° (d) 60°

Last Answer : (c) 45°

The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Description : The size of the weld in butt welded joint is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Last Answer : (b) Throat of weld

In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Description : In transverse fillet welded joint, the size of weld is equal to (a) 0.5 × Throat of weld (b) Throat of weld (c) 2 × Throat of weld (d) 2 × Throat of weld

Last Answer : (c) 2 × Throat of weld

Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Description : Maximum shear stress in transverse fillet weld of leg h and length l is a) P/hl b) 1.21P/hl c) P/1.21hl d) None of the listed

Last Answer : b) 1.21P/hl