What is the Difference between agitator and impeller in a washing machine?

What is the Difference between agitator and impeller in a washing machine?
by

1 Answer

Answer :

What is the answer ?
by

Related questions

What is an agitator and how is it used?

Description : What is an agitator and how is it used?

Last Answer : An agitator is a device or mechanism to put something into motion by shaking or stirring. There are several different types of agitators, such as manual, a washing machine agitator, and a magnetic agitator.

Helical screw agitator is used for (A) Mixing highly viscous pastes (B) Blending immiscible liquids (C) Mixing liquids at very high temperature (> 250 °C) (D) None of these

Description : Helical screw agitator is used for (A) Mixing highly viscous pastes (B) Blending immiscible liquids (C) Mixing liquids at very high temperature (> 250 °C) (D) None of these

Last Answer : (A) Mixing highly viscous pastes

The most suitable equipment used to devulcanise rubber scrap and to make water dispersion & rubber solution is a (A) Boundary mixer (B) Propeller agitator (C) Sharpies centrifuge

Description : The most suitable equipment used to devulcanise rubber scrap and to make water dispersion & rubber solution is a (A) Boundary mixer (B) Propeller agitator (C) Sharpies centrifuge

Last Answer : (A) Boundary mixer

Which of the following is the most suitable for handling fibrous and dense slurries? (A) Propeller agitator (B) Cone type agitator (C) Turbine agitator

Description : Which of the following is the most suitable for handling fibrous and dense slurries? (A) Propeller agitator (B) Cone type agitator (C) Turbine agitator

Last Answer : (B) Cone type agitator

Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Description : Paddle agitator (A) Is suitable for mixing low viscosity liquids (B) Produces axial flow (C) Moves at very high speed (D) None of these

Last Answer : (A) Is suitable for mixing low viscosity liquids

About 2-3 hp, power per gallon of a thin liquid provides vigorous agitation in an agitator. 'Power number' in agitation is given by (A) P. gc /n 3 . D2 . ρ (B) P. gc . ρ/µ

Description : About 2-3 hp, power per gallon of a thin liquid provides vigorous agitation in an agitator. 'Power number' in agitation is given by (A) P. gc /n 3 . D2 . ρ (B) P. gc . ρ/µ

Last Answer : (A) P. gc /n 3 . D2 . ρ

Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow (C) Generally, the diameter of the agitator is kept between l/3rd to l/6th of the tank diameter while the blade length is l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Description : Pick out the wrong statement pertaining to the turbine agitator. (A) Recommended peripheral speed for the turbine agitator is 200-250 metres/minute (B) Pitched blade turbine agitator gives only radial flow with ... l/4th of agitator diameter (with central disc, it is l/8th of the agitator diameter)

Last Answer : (B) Pitched blade turbine agitator gives only radial flow with complete absence of the axial flow

A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Description : A propeller agitator (A) Produces mainly axial flow (B) Is used for mixing high viscosity pastes (C) Runs at very slow speed (2 rpm) (D) All (A), (B) and (C)

Last Answer : (A) Produces mainly axial flow

Laminar flow region is said to exist during agitation of a liquid in an agitator, when the value of Reynolds number is (A) > 10 (B) < 10 (C) > 100 (D) < 100

Description : Laminar flow region is said to exist during agitation of a liquid in an agitator, when the value of Reynolds number is (A) > 10 (B) < 10 (C) > 100 (D) < 100

Last Answer : (B) < 10

Agitator is provided in a crystalliser for(A) Avoiding deposition on cooler surfaces(B) Formation of nuclei(C) Crystal growth(D) All (A), (B) and (C)

Description : Agitator is provided in a crystalliser for (A) Avoiding deposition on cooler surfaces (B) Formation of nuclei (C) Crystal growth (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

In Joule's experiment, an insulated container contains 20 kg of waterinitially at 25°C. It is stirred by an agitator, which is made to turn by aslowly falling body weighing 40 kg through a height of 4 m. The process isrepeated 500 times. The acceleration due to gravity is 9.8 ms-2. Neglectingthe heat capacity of agitator, the temperature of water (in °C) is(A) 40.5(B) 34.4(C) 26.8(D) 25

Description : In Joule's experiment, an insulated container contains 20 kg of waterinitially at 25°C. It is stirred by an agitator, which is made to turn by a slowly falling body weighing 40 kg through a height of 4 m. The process is repeated ... temperature of water (in °C) is (A) 40.5 (B) 34.4 (C) 26.8 (D) 25

Last Answer : (B) 34.4

Scale up of agitator design requires (A) Geometrical similarity only (B) Dynamic similarity only (C) Both geometrical and dynamic similarity (D) All geometrical, dynamic and kinematic similarity

Description : Scale up of agitator design requires (A) Geometrical similarity only (B) Dynamic similarity only (C) Both geometrical and dynamic similarity (D) All geometrical, dynamic and kinematic similarity

Last Answer : (D) All geometrical, dynamic and kinematic similarity

A Power sprayer essentially consists of: a) Tank a) Agitator b) Pressure Gauge c) All of the above

Description : A Power sprayer essentially consists of: a) Tank a) Agitator b) Pressure Gauge c) All of the above

Last Answer : All of the above

BABE RUTH was a: (a) Priest (b) Political Agitator (c) Player

Description : BABE RUTH was a: (a) Priest (b) Political Agitator (c) Player

Last Answer : (c) Player

Agitator(propeller or paddle)type for agitating liquid in power sprays have a velocity of a.100-120 rpm b.60-100 rpm c.10-20 rpm d. none of the above

Description : Agitator(propeller or paddle)type for agitating liquid in power sprays have a velocity of a.100-120 rpm b.60-100 rpm c.10-20 rpm d. none of the above

Last Answer : a.100-120 rpm

The metering mechanism which is most suitable for metering of small seed is to handle is a. Internal double run mechanism b. Fluted wheel mechanism c. Stationery opening with agitator d. None of the above

Description : The metering mechanism which is most suitable for metering of small seed is to handle is a. Internal double run mechanism b. Fluted wheel mechanism c. Stationery opening with agitator d. None of the above

Last Answer : b. Fluted wheel mechanism

Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Description : Most commonly used metering device for bulk flow seed metering of small and medium size seeds (grains) a) Fluted wheel b) Internal double run c) Stationary opening with agitator d) None of the above

Last Answer : a) Fluted wheel

In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

Description : In centrifugal compressor terminology, vaneless space refers to the space between A. The inlet and blade inlet edge B. Blades in the impeller C. Diffuser exit and volute casing D. Impeller tip and diffuser inlet edge

Last Answer : ANSWER : D

Which one of the following statements is correct? A. Reciprocating compressors are used to supply large quantities of air at a lower pressure ratio B. Centrifugal compressors are used to supply large quantities of air at a lower pressure ratio C. Centrifugal compressors are used to supply small quantities of air at a lower pressure ratio D. Centrifugal compressors cannot be run at high speed because of impeller, diffuser and casing.

Description : Which one of the following statements is correct? A. Reciprocating compressors are used to supply large quantities of air at a lower pressure ratio B. Centrifugal compressors are used to supply ... . Centrifugal compressors cannot be run at high speed because of impeller, diffuser and casing.

Last Answer : ANSWER : B

Which one of the following types of impeller vanes are most commonly used in centrifugal type compressors? A. Forward curved B. Radial C. Backward curved D. Tangential

Description : Which one of the following types of impeller vanes are most commonly used in centrifugal type compressors? A. Forward curved B. Radial C. Backward curved D. Tangential

Last Answer : ANSWER : C

The pressure rise in the impeller of centrifugal compressor is achieved by A. the decrease in volume and diffusion action B. the centrifugal action and decrease in volume C. the centrifugal and diffusion action D. the centrifugal and push pull action

Description : The pressure rise in the impeller of centrifugal compressor is achieved by A. the decrease in volume and diffusion action B. the centrifugal action and decrease in volume C. the centrifugal and diffusion action D. the centrifugal and push pull action

Last Answer : ANSWER : D

What do you call a circuit that controls the magnetron output?A. Inverter B. Impeller C. Modulator D. Converter

Description : What do you call a circuit that controls the magnetron output? A. Inverter B. Impeller C. Modulator D. Converter

Last Answer : C. Modulator

For a turbine agitated and baffled tank, operating at low Reynold's number (based on impeller diameter), the power number (Np ) varies with NRe as (A) Np ∝ NRe (B) Np ∝ √NRe (C) Np → constan(D) Np ∝ 1/NRe

Description : For a turbine agitated and baffled tank, operating at low Reynold's number (based on impeller diameter), the power number (Np ) varies with NRe as (A) Np ∝ NRe (B) Np ∝ √NRe (C) Np → constan (D) Np ∝ 1/NRe

Last Answer : (D) Np ∝ 1/NRe

During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Description : During agitation of liquids, power consumption during laminar flow is not proportional to the (A) Density of the liquid (B) Viscosity of the liquid (C) Cube of impeller diameters (D) Square of rotational speed

Last Answer : (A) Density of the liquid

The power number for a stirred tank becomes constant at high Reynolds number. In this limit, the variation of power input with impeller rotational speed (N) is proportional to (A) N° (B) N 1 (C) N 2 (D) N 3

Description : The power number for a stirred tank becomes constant at high Reynolds number. In this limit, the variation of power input with impeller rotational speed (N) is proportional to (A) N° (B) N 1 (C) N 2 (D) N 3

Last Answer : (C) N

During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, but is dependent on the geometry of the impeller (C) Froude number is used to account for the effect of surface (e.g., the centre vortex) on the power number (D) All (A), (B) and (C)

Description : During agitation of liquids, the (A) Froude number is independent for the curves between power number and Reynolds number in baffled system (B) Power number becomes independent of impellers Reynolds number at high Reynolds number, ... , the centre vortex) on the power number (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 /μ: Reynold's number N is the impeller rotational speed, and D is the impeller diameter. (A) Po ∝ Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Description : At low Reynold's number, the power (P) required for agitating a fluid in a stirred tank becomes independent of inertial forces. In this limit, indicate which of the following relations is satisfied: Po = ρ/ρN3 D5 : Power number Re = ρ N D2 ... Re -1.0 (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5 (D) Po ∝ Re 1.0

Last Answer : (B) Po ∝ Re 0.0 (C) Po ∝ Re 0.5

Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The clearance between the tank bottom and the bottom most impeller should be about (where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Description : Height of liquid in agitation tank is normally maintained equal to the tank diameter. However, if the tank is too tall and a large liquid hold up is desired, then two or more impellers mounted on the same shaft may be used. The ... where, D = impeller diameter) (A) 0.5 D (B) D (C) 1.5 D (D) 2 D

Last Answer : (B) D

Turbine impeller (A) Produces only radial current (B) Produces only tangential current (C) Is effective over wide range of viscosities (D) Does not produce tangential current

Description : Turbine impeller (A) Produces only radial current (B) Produces only tangential current (C) Is effective over wide range of viscosities (D) Does not produce tangential current

Last Answer : (C) Is effective over wide range of viscosities

Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) NPSH required (B) BHP required by the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Description : Consider a centrifugal pump having a specific impeller diameter, fixed impeller speed pumping a liquid of constant density at a particular discharge capacity. With decrease in the capacity of the pump, the __________ decreases. (A) ... the pump (C) Head of the liquid pumped (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these

Description : The pump impeller and the turbine runner in a hydraulic torque converter (A) Have the same diameter (B) Have different diameters (C) Are directly coupled (D) None of these

Last Answer : (B) Have different diameters

With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Description : With a constant diameter impeller of a centrifugal pump (A) Its capacity varies directly as the square of speed (B) Head varies as the square of speed (C) Horsepower input varies as the square of speed (D) Head varies as the speed

Last Answer : (B) Head varies as the square of speed

The maximum head that can be developed by a single impeller is __________ ft(A) 25(B) 100(C) 250-300(D) 1000.

Description : The maximum head that can be developed by a single impeller is __________ ft. (A) 25 (B) 100 (C) 250-300 (D) 1000

Last Answer : (C) 250-300

Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes in the impeller (C) Mounting of two or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Description : Which of the following options will facilitate the achievement of a very high head (say 30 metres) in case of a centrifugal pump? (A) Increasing the impeller speed and the volute area (B) Increasing the number of vanes ... or more impellers in series on a single shaft (D) Either of (A), (B) or (C)

Last Answer : (C) Mounting of two or more impellers in series on a single shaft

Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Description : Priming of a centrifugal pump is done to (A) Increase the mass flow rate of fluid (B) Develop effective pressure rise by the pump (C) Avoid chances of separation inside the impeller (D) None of these

Last Answer : (C) Avoid chances of separation inside the impeller

The most important factor, which determines the maximum height to which water can be lifted by a pump at standard temperature is the (A) Barometric pressure (B) Speed of the impeller (C) Diameter of the impeller (D) Both (B) and (C)

Description : The most important factor, which determines the maximum height to which water can be lifted by a pump at standard temperature is the (A) Barometric pressure (B) Speed of the impeller (C) Diameter of the impeller (D) Both (B) and (C)

Last Answer : (A) Barometric pressure

Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Description : Centrifugal pump is normally classified on the basis of the (A) rpm (B) Type of casing (C) Impeller blade angle (D) Number of blades in impeller

Last Answer : (B) Type of casing

Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Description : Theoretical head developed by a centrifugal pump does not depend upon the __________ the impeller. (A) Radius of (B) Speed of (C) Fluid velocity leaving (D) None of these

Last Answer : (D) None of these

In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Description : In case of a centrifugal pump, the ratio of total delivered pressure to pressure developed with the impeller is called the __________ efficiency. (A) Manometric (B) Mechanical (C) Volumetric (D) Overall

Last Answer : (A) Manometric

Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Description : Head developed by a centrifugal pump depends on its (A) Speed (B) Impeller diameter (C) Both (A) and (B) (D) Neither (A) nor (B)

Last Answer : C) Both (A) and (B)

Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Description : Which is the correct relationship for a centrifugal pump? (Where, D = Impeller diameter, inches H = Head developed, ft of liquid pumped N = Speed of pump, rpm) (A) D = 1840 H0.5 /N (B) D = 1840 N/H0.5 (C) H = 1840 D0.5 /N (D) D = 1840 H/N

Last Answer : (A) D = 1840 H0.5 /N

At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Description : At a constant speed of the centrifugal pump, it’s __________ the impeller diameter. (A) Capacity varies directly with (B) Head varies as the square of (C) Horsepower varies as the cube of (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Description : A centrifugal pump is called a turbine pump, if it is having a (A) Turbine type impeller (B) Vaned diffusion casing (C) Rotating vaned volute (D) None of these

Last Answer : (B) Vaned diffusion casing

Power required for mixing Newtonian fluids is a function of the (A) Speed of impeller, diameter of impeller & viscosity (B) Density & viscosity of fluid only (C) Density of fluid, viscosity of fluid & impeller dia only (D) None of these

Description : Power required for mixing Newtonian fluids is a function of the (A) Speed of impeller, diameter of impeller & viscosity (B) Density & viscosity of fluid only (C) Density of fluid, viscosity of fluid & impeller dia only (D) None of these

Last Answer : (D) None of these

The head developed by a centrifugal pump is largely determined by the (A) Power of the pump(B) Nature of the liquid being pumped(C) Angle of the vanes and the speed of the tip of the impeller(D) Vapour pressure of the liquid

Description : The head developed by a centrifugal pump is largely determined by the (A) Power of the pump (B) Nature of the liquid being pumped (C) Angle of the vanes and the speed of the tip of the impeller (D) Vapour pressure of the liquid

Last Answer : (C) Angle of the vanes and the speed of the tip of the impeller

In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Description : In case of a centrifugal pump, the theoretical head developed is dependent on the __________ the impeller. (A) Speed of (B) Diameter of (C) Fluid velocity leaving (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)

A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Description : A mixed flow centrifugal pump (A) Employs such an impeller, through which the flow is a combination of radial & axial flow (B) Mixes the two fluids before pumping them (C) Pumps the two fluids separately and then mixes them (D) Employs impellers in both the radial & axial directions

Last Answer : (A) Employs such an impeller, through which the flow is a combination of radial & axial flow

Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Description : Propellers are (A) Axial flow mixers (B) Low speed impeller (C) Used for mixing liquids of high viscosity (D) Radial flow mixers

Last Answer : (A) Axial flow mixers

Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Description : Erosion and pits formation on the impeller of a centrifugal pump may be due to (A) Cavitation (B) Low speed of impeller (C) Its operation with delivery valve closed for considerable time after starting the pump (D) Off centering of pump with motor

Last Answer : (A) Cavitation

The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Description : The capacity of a centrifugal pump Can be increased by increasing the (A) Impeller diameter or speed (B) Number of pumps and joining them in series (C) Number of pumps and joining them in parallel (D) All (A), (B) and (C)

Last Answer : (D) All (A), (B) and (C)