Construct a two handed process chart for an activity of replacing old refill from the ball pen with summary.

 Construct a two handed process chart for an activity of replacing old refill from the ball pen with summary.
by

1 Answer

Answer :

Two handed process chart Date of charting – 20/11/2019

Activity- Replacing old refill from ball pen charted by - XYZ

Chart begins – both hands free before activity

Chart ends – both hands free after activity


image


Summary

image

by

Related questions

Prepare outline process chart for replacement of battery in a car.

Description : Prepare outline process chart for replacement of battery in a car. 

Last Answer : Outline process chart for replacement of battery in a car. Task/Job “Replacement battery in a car Charted by: XYZ Chart begins with: Disconnect the electric supply Charted by: ABC Chart ends with: Replace with new battery Date: 18/04/2018

Explain the different recording techniques used in method study. Also outline process chart for checking diameter of 50mm of shaft.

Description : Explain the different recording techniques used in method study. Also outline process chart for checking diameter of 50mm of shaft.

Last Answer : Different recording techniques used in method study: Process charts are used to record the data systematically so that none of the information needed for study and analysis is missed. A. Chart indicating ... area. However, there is no indication of the direction or speed of motion.

Explain how Gantt chart is used in project planning with proper example.

Description : Explain how Gantt chart is used in project planning with proper example. 

Last Answer : Use of Gantt Chart in Project Planning: Gantt Chart is a project planning tool that can be used to represent the timing of tasks required to complete a project. Because Gantt chats are simple to ... a chart, which are used to record the actual operating times and delays of workers and machines.

Explain the GANTT chart used in PPC. Enlist advantages and disadvantages of it

Description : Explain the GANTT chart used in PPC. Enlist advantages and disadvantages of it

Last Answer : Gantt chart used in production planning and control. Gantt Chart is a project planning tool that can be used to represent the timing of tasks required to complete a project. Because Gantt chats ... time to maintain. 4. Lack of adequate depiction interrelationship between the separate tasks.

Explain the cycle of Kaizen activity.

Description : Explain the cycle of Kaizen activity.

Last Answer : Cycle of Kaizen activity. Kai means Change and Zen means for the better. Kaizen is a Japanese term that basically translated to continuous improvement or change to become good is a management concept ... the same. Act according to the action plan. This cycle is also called as PDCA cycle.

What's the best refill for a Big i Design TI pen?

Description : What's the best refill for a Big i Design TI pen?

Last Answer : answer:Welcome to Fluther. If I were you, buying a high-end pen and specifying my own refill / cartridge, I'd go for the space pen pressurized cartridge. Those things have been great. When I worked in ... , through water, grease and dirt and in any position. And I never had one leak on me, either.

Is there a better refill for Wacom Inkling pen?

Description : Is there a better refill for Wacom Inkling pen?

Last Answer : Their website says you can use any standard mini ballpoint refills with a 1.0 mm ball size.

Explain the various steps for planning a process for product from raw material to finished product in an industry.

Description : Explain the various steps for planning a process for product from raw material to finished product in an industry.

Last Answer : 1. Analysis of Product and its specification: - During analysis, following parameter should be considereda. Drawing and specification of product. b. Quality of product. c. Number of parts/components per ... and fixing the rates of payment. 11. Prepare the route sheet and operation sheet.

What are the factors to be considered to determine stages of inspection during process planning?

Description : What are the factors to be considered to determine stages of inspection during process planning?

Last Answer : Factors to be considered to determine stages of Inspection during Process Planning: 1. Type of Production System 2. Type of Facility Layout 3. Type (Nature) of Product/Components 4. ... /Equipments used 5. Application of the Product/Components etc. 6. Strength/characteristics of the product

Prepare operation process sheet and decide sequence of operation for the component shown in Figure No. 1. Assume suitable material and cutting conditions.

Description : Prepare operation process sheet and decide sequence of operation for the component shown in Figure No. 1. Assume suitable material and cutting conditions.

Last Answer : Operation Sheet with correct sequence of operations for the above given component by assuming suitable material and cutting conditions is as shown in below table;

State the information required to do process planning. What is working drawing?

Description : State the information required to do process planning. What is working drawing?

Last Answer : Information required to do process planning: [1] Assembly and Part drawings and Bill of Materials [2] Technical Details of Machine/Equipment to be used [3] Standard Times for operation ... their functional positions or as an exploded view where we relate the parts to their functional positions.

Explain in brief steps involved in process planning.

Description : Explain in brief steps involved in process planning.

Last Answer : Steps involved in process planning: 1. Analysis of Product and its specification: - During analysis, following parameter should be considered, a. Drawing and specification of product. b. Quality of ... and fixing the rates of payment. 11. Prepare the route sheet and operation sheet.

State the different factors affecting process planning.

Description : State the different factors affecting process planning. 

Last Answer : Factors affecting process planning. a. Size and shape of part: The size and shape of many components decides the basic operations for the manufacturing of pert. For example : For manufacturing ... give process engineer sufficient time to go details of each aspect to select most economical process.

Differentiate between product layout and process layout on the basis of 1) Initial investment cost. 2) Cycle Time. 3) Types of machines used. 4) Skill of labour required. 5) Inventory level. 6) Arrangement of machine.

Description : Differentiate between product layout and process layout on the basis of 1) Initial investment cost. 2) Cycle Time. 3) Types of machines used. 4) Skill of labour required. 5) Inventory level. 6) Arrangement of machine. 

Last Answer : Parameter Product layout Process layout 1) Initial investment cost. It requires higher initial investment. Less initial investment 2) Cycle Time. Less cycle time for ... similar operation are grouped together to make a section, like lathe section, milling section etc.

Define process planning. State the factors affecting process planning and explain it.

Description : Define process planning. State the factors affecting process planning and explain it.

Last Answer : Definition of Process planning: Process planning can be defined as the systematic determination of the process by which a product is to be manufactured economically and competitively. Factors ... process engineer sufficient time to go details of each aspect to select most economical process.

Explain the factor affecting process planning.

Description : Explain the factor affecting process planning.

Last Answer : Factors affecting process planning. a. Size and shape of part: The size and shape of many components decides the basic operations for the manufacturing of pert. For example : For manufacturing ... process engineer sufficient time to go details of each aspect to select most economical process. 

Define process planning and explain the steps in process planning.

Description : Define process planning and explain the steps in process planning.

Last Answer : Process Planning is the selection of a systematic method or process by which the product is to be manufactured economically and competitively. Steps: 1) Study of part drawings and its specifications. ... product. 10) Preparation of route and operation sheet which is also called process sheet.  

Explain in brief product and process type layout

Description : Explain in brief product and process type layout

Last Answer : Product Layout:- It is also known as line layout. It implies that various operations on raw materials are performed in a sequence and the machines are placed along the product flow line i.e. machines are ... lathes will be at one place, all milling machines will be at one place etc

Define process planning and state its functions

Description : Define process planning and state its functions

Last Answer : Process Planning  Process planning can be defined as the systematic determination of the methods by which a product is to be manufactured, economically and competitively. Process planning consists of devising, selecting ... generation of NC part program. [8] To design the Jig and Fixture.

List down eight important steps for planning a process for a product from raw material to finished product in an industry.

Description : List down eight important steps for planning a process for a product from raw material to finished product in an industry.

Last Answer : Steps for Process Planning for a Product from Raw Material to Finished Product: Specific activities involved in planning a process for a product from raw material to finished product in an ... gauges required for inspection. This operation described in detail, in later section of this chapter.

State the importance of operation sheet. How will it help you to improve process planning?

Description : State the importance of operation sheet. How will it help you to improve process planning?

Last Answer : Importance of operation Sheet: [1] A process planning used in the routing which is also known as Route Sheet, Process Sheet or Operation Sheet. [2] It consists of details of operations, sequences, types ... to determine the efficiency of a work centre. [6] It helps to trace the material movement.

State and explain various factors affecting process planning.

Description : State and explain various factors affecting process planning.

Last Answer : Factors affecting process planning:  a. Size and shape of part: The size and shape of many components decides the basic operations for the manufacturing of pert. For example : For ... generally do not allow process engineer to select most economical process and tool for economic production. 

Define plant layout. Explain in detail 'Process layout' with neat sketch.

Description : Define plant layout. Explain in detail 'Process layout' with neat sketch.

Last Answer : Definition of Plant layout It is defined as the systematic arranging of various facilities like equipments, machines manpower, and inspection areas, etc and services within the area  of plant ... required for product manufacturing Less cost of investment General purpose machines are used

XI. Answer any TWO of the following questions.47) On the basis of data you have collected regarding participation of women in your locality in below mentioned catagories construct a pie chart.a) Self employed.b) Regular salaried employees.c) Causel wage labours.

Description : XI. Answer any TWO of the following questions.47) On the basis of data you have collected regarding participation of women in your locality in below mentioned catagories construct a pie chart.a) Self employed.b) Regular salaried employees.c) Causel wage labours.

Last Answer : XI. Answer any TWO of the following questions. 47) On the basis of data you have ... Regular salaried employees. c) Causel wage labours.

Explain the concept of AGV? State it’s any two applications.

Description :  Explain the concept of AGV? State it’s any two applications. 

Last Answer : AGV is the battery operated programmed vehicle, used to carry load from one location to another by following a prescribed path around the manufacturing floor. It is a driverless vehicle, ... System) 2) AGV material handling system is very suited to computer integrated manufacturing system  

Enlist any four factors which affect selection of material handling system. Explain which type of material handling system is suitable for: (i) Unloading two wheelers from truck ii) Stacking of pallets in store racks.

Description : Enlist any four factors which affect selection of material handling system. Explain which type of material handling system is suitable for: (i) Unloading two wheelers from truck ii) Stacking of pallets in store racks.

Last Answer : Four Factors affecting Selection of Material Handling System: [1] Adaptability and Flexibility [2] Type of Material to be handled [3] Type of Layout [4] Type of Production [5] ... [11] Cost of installation and handling Suitable Material Handling Devices for Following Activities:

Draw the layout of two wheeler service station. Justify the type of layout you have adopted.

Description : Draw the layout of two wheeler service station. Justify the type of layout you have adopted.

Last Answer : Layout of Two Wheeler Service Station: [1] The major factors considered for service station, is an impact of location on sales and services and customer satisfaction. [2] Customers usually look about how close ... a process type of layout and they are assembled using product type of layout.

Explain any two clamping devices with neat sketch

Description : Explain any two clamping devices with neat sketch

Last Answer : [1] Screw clamp:- It is particularly useful when a component is to be gripped on its edges. This arrangement insures easy machining of top surface of work piece. [2] Equalizing clamp: - It ... is operated by simply actuating the handle up or down which locks or unlocks the strap with the work.

Describe any two types of joints used in robotic arm and wrist

Description : Describe any two types of joints used in robotic arm and wrist

Last Answer : [1] Rotational joint [2] Linear joint [3] Twisting joint [4] Orthogonal & [5] Revolving joint Rotational Joint:Rotational joint can also be represented as R - Joint. This type will allow the ... the rotational axes. As like twisting joint, the output link spins about the input link.

What is combine operation? Give two examples of combined operations.

Description : What is combine operation? Give two examples of combined operations.

Last Answer : Combined Operation: 1. In order to save the operation and setting time of part, while the part is subjected to machining process, the different operations to be performed are combined together or ... etc. 2. Integration Method: Operation on turret lathe, multi spindle automats, CNC operations etc.

Describe any two joint types used in Robotic arm and wrist.

Description : Describe any two joint types used in Robotic arm and wrist.

Last Answer : Joint types used in robotic arm: 1) Linear Joint or Prismatic joint: The linear joint provides the translational sliding motion between the input and output link. The axes of the links are parallel ... to the axis of rotation of the joint. The revolving joint is shown in fig.(e)

Explain with neat sketch any two material handling devices used in mass production.

Description : Explain with neat sketch any two material handling devices used in mass production.

Last Answer : 1.Roller conveyors may be gravity aided or powered and are employed for transporting products having flat bottoms. Bigger jobs can be handled as they are, whereas small items are put in boxes, tins ... and unloading of the products.   4.Screw Conveyor, Pneumatic Conveyor, Elevated Conveyor . 

Describe any two joints types used in robotics arms and wrist

Description : Describe any two joints types used in robotics arms and wrist 

Last Answer : Joint used in robotics arm: 1) Linear Joint or Prismatic joint: The linear joint provides the translational sliding motion between the input and output link. The axes of the links are parallel to one ... the axis of rotation of the joint. The revolving joint is shown in fig.(e)

Explain the procedure of measurement of productivity? Discuss any two techniques.

Description : Explain the procedure of measurement of productivity? Discuss any two techniques.

Last Answer : Productivity Measurement: [1] Measurement plays an important role in management of productivity. It helps to determine organization is progressing well or not. It also provides information on how effectively and ... give us the productivity of an entire organization or even a nation.

List the different actuators. Explain any two types of actuators with advantages and disadvantages

Description : List the different actuators. Explain any two types of actuators with advantages and disadvantages

Last Answer : Actuators [1] Hydraulic Actuator [2] Electrical Actuator [3] Pneumatic Actuator [4] Mechanical Actuator Hydraulic Actuator According to Pascal, when there is an increase in ... efficiency Disadvantages [1] Requires more power [2] Possibilities of fire hazards / accidents

Enlist types of joints used in robotic arm and draw sketch of any two

Description : Enlist types of joints used in robotic arm and draw sketch of any two

Last Answer : Types of Joints [1] Linear Joint or Prismatic joint [2] Orthogonal Joint [3] Rotational joint [4] Twisting Joint [5] Revolving joint

From which of the following is robot programming language. (A) VAL (B) AML(C) ABD (D) Both (A) & (B)

Description : From which of the following is robot programming language. (A) VAL (B) AML (C) ABD (D) Both (A) & (B)

Last Answer : D

____ grippers are used to transfer ferrous material. (A) Magnetic grippers (B) Mechanical grippers (C) Adhesive grippers (D) Vacuum cup grippers

Description : ____ grippers are used to transfer ferrous material. (A) Magnetic grippers (B) Mechanical grippers (C) Adhesive grippers (D) Vacuum cup grippers

Last Answer : A

____ grippers are used to pick up light weight materials such as paper,cloth etc. (A) Mechanical grippers (B) Adhesive grippers (C) Vacuum cup grippers (D) Magnetic grippers

Description : ____ grippers are used to pick up light weight materials such as paper,cloth etc. (A) Mechanical grippers (B) Adhesive grippers (C) Vacuum cup grippers (D) Magnetic grippers

Last Answer : B

From which of the following is the type of robot. (A) Point to point robots (B) Continue path robot (C) Jointed arm robots (D) All of the above

Description : From which of the following is the type of robot. (A) Point to point robots (B) Continue path robot (C) Jointed arm robots (D) All of the above

Last Answer : D

Grippers are used to_____. (A) Hold the objects (B) Sense the objects (C) Move the objects (D) Both (A) & (C)

Description : Grippers are used to_____. (A) Hold the objects (B) Sense the objects (C) Move the objects (D) Both (A) & (C)

Last Answer : D

The capacity of robot to carry load is known as_____. (A) Load carrying capacity (B) Work envelope (C) Maximum reach (D) None of the above

Description : The capacity of robot to carry load is known as_____. (A) Load carrying capacity (B) Work envelope (C) Maximum reach (D) None of the above

Last Answer : A

The capacity of robot to carry load is known as_____. (A) Load carrying capacity (B) Work envelope (C) Maximum reach (D) None of the above

Description : The capacity of robot to carry load is known as_____. (A) Load carrying capacity (B) Work envelope (C) Maximum reach (D) None of the above

Last Answer : C

The speed at which robot is capable of manipulating its end effector is known as the____. (A) Velocity of robot (B) Maximum reach (C) Speed of movement (D) Load carrying capacity

Description : The speed at which robot is capable of manipulating its end effector is known as the____. (A) Velocity of robot (B) Maximum reach (C) Speed of movement (D) Load carrying capacity

Last Answer : C

Which is also known as work volume of robot. (A) Work envelope (B) Speed of movement(C) Load carrying capacity (D) Precision of movement

Description : Which is also known as work volume of robot. (A) Work envelope (B) Speed of movement(C) Load carrying capacity (D) Precision of movement

Last Answer : A

From which of the following is benefit of robot. (A) Variety of task (B) Computer control (C) Repetitive task (D) All of the above

Description : From which of the following is benefit of robot. (A) Variety of task (B) Computer control (C) Repetitive task (D) All of the above

Last Answer : D

Which is area of engineering and science which understand the different principles, structure and programming of robot. (A) Mechatronics (B) Robotics (C) Aeronautics (D) None of the above

Description : Which is area of engineering and science which understand the different principles, structure and programming of robot. (A) Mechatronics (B) Robotics (C) Aeronautics (D) None of the above

Last Answer : B

What is end effector? Give its classification

Description : What is end effector? Give its classification 

Last Answer : In robotics, an end effector is a device or tool that's connected to the end of a robot arm where the hand would be. The end effector is the part of the robot that interacts with the ... designed. Classification:- i) Mechanical clamping ii) Magnetic clamping iii) Vocum (suction) gripping

How ‘5s’ can be used as inventory reduction technique?

Description : How ‘5s’ can be used as inventory reduction technique? 

Last Answer : By applying 5S in industry to systematically results- Total organization, cleanliness and standardization in work piece. Well organized workplace. More efficient workplace. More ... of waste & making cleanliness  4. SEIKETSU means standardizing 5. SHITSUKE means self discipline 

What allowances are considered while calculating standard time?

Description : What allowances are considered while calculating standard time? 

Last Answer : following types of allowances are considered while calculating standard time. 1) Relaxation allowance a) Personal need allowance b) Fatigue allowance i) Basic fatigue allowance ii) Variable ... 2) Contingency allowance 3) Special allowance 4) Process allowance 5) Interference allowance