Voltage dependent resistors are usually made from?

Voltage dependent resistors are usually made from?

by

1 Answer

Answer :

Voltage dependent resistors are usually made from nichrome.

by

Related questions

Voltage dependent resistors are used?

Description : Voltage dependent resistors are used?

Last Answer : Voltage dependent resistors are used to supress surges.

Nodal Analysis with Voltage Sources dependent voltage source and two supernode

Description : Nodal Analysis with Voltage Sources dependent voltage source and two supernode

Last Answer : Nodal Analysis with Voltage Sources dependent voltage source and two supernode

A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the

Description : A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will

Last Answer : A network contains linear resistors and ideal voltage sources. If values of all the resistors are doubled then the voltage across each resistor will not change

Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage

Description : Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

Last Answer : Consider a circuit with four resistors in series connected to a voltage source. What happens to the voltage across each resistor, if the value of each of the resistors is doubled? A) It will double B) It will remain the same C) It will be halved D) It will become zero

Three identical resistors are first connected in parallel and then in series...

Description : Three identical resistors are first connected in parallel and then in series. The resultant resistance of the first combination to the second will be?

Last Answer : Three identical resistors are first connected in parallel and then in series. The resultant resistance of the first combination to the second will be 1/9 times.

Two resistors are said to be connected in series when?

Description : Two resistors are said to be connected in series when?

Last Answer : Two resistors are said to be connected in series when same current passes in turn through both.

what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Description : what is equivalent resistance when four 4 Ohm resistors are connected in i) series ii) parallel

Last Answer : equivalent resistance

State any two features of carbon composition resistors.

Description : State any two features of carbon composition resistors.

Last Answer : Features of Carbon composition resistance: i) Low cost ii) Wide resistance range ( ohm to mega ohm) iii) Wide range of working voltage iv) Simple in construction 

The colour band on the extreme left in general purpose fixed resistors represents:

Description : The colour band on the extreme left in general purpose fixed resistors represents: A) Tolerance B) First significant digit C) Wattage Rating D) Voltage Rating

Last Answer : The colour band on the extreme left in general purpose fixed resistors represents: First significant digit

Three identical resistors connected in star consume 5000 W. If the resistors are connected in

Description : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be

Last Answer : Three identical resistors connected in star consume 5000 W. If the resistors are connected in delta across the same supply, the power consumed will be 15000 W

When three resistors with unequal values are connected in parallel, _______

Description : When three resistors with unequal values are connected in parallel, _______ A) The current across the resistors is the same  B) The voltage drop across the resistors is the same C) The voltage drops across the resistors is proportional to the resistance of each resistor D) None of these

Last Answer : When three resistors with unequal values are connected in parallel, The voltage drop across the resistors is the same

What is the total resistance if 5 resistors of 20 Ω each are connected in series?

Description : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Last Answer : What is the total resistance if 5 resistors of 20 Ω each are connected in series? A) 100 Ω B) 4 Ω C) 20 Ω D) None of these

Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is

Description : Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is 5 A. What will be the current if the above 4 resistors are connected in parallel? A) 5 A B) 50 A C) 500 A D) None of these

Last Answer : Consider a circuit with four 10 Ω resistors connected in parallel and the current flowing through the circuit is 5 A. What will be the current if the above 4 resistors are connected in parallel? A) 5 A B) 50 A C) 500 A D) None of these

The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as?

Description : The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as

Last Answer : The circuit has resistors, capacitors and semi-conductor diodes. The circuit will be known as non-linear circuit.

Wire-wound resistors are unsuitable for use at high frequencies because they?

Description : Wire-wound resistors are unsuitable for use at high frequencies because they?

Last Answer : Wire-wound resistors are unsuitable for use at high frequencies because they exhibit unwanted inductive and capacitive effects.

Your Twilight Zone moment; you are alone on the planet, how long before everything goes bad?

Description : Your Twilight Zone moment; you are alone on the planet, how long before everything goes bad?

Last Answer : This is it – ZERO HOUR!

When a voltage of one volt is applied, a circuit allows one micro ..

Description : When a voltage of one volt is applied, a circuit allows one micro ampere current to flow through it. The conductance of the circuit is?

Last Answer : If v = 1 volt and i = 1 micro amp, i= 10^(-6)   So R = V/I,  R= 1/10^(-6) , R= 10^6  And now Conductance G = 1/R  So G = 10^(-6) mho..... Answer

Two resistances Rl and Ri are connected in series across the voltage...

Description : Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across?

Last Answer : Two resistances Rl and Ri are connected in series across the voltage source where Rl>Ri. The largest drop will be across Rl.

Which of the following is usually not the generating voltage ? (a) 6.6 kV (b) 8.8 kV (c) 11 kV (d) 13.2 kV

Description : Which of the following is usually not the generating voltage ? (a) 6.6 kV (b) 8.8 kV (c) 11 kV (d) 13.2 kV

Last Answer : (b) 8.8 kV

The voltage used for suburban trains in D.C. system is usually?

Last Answer : The voltage used for suburban trains in D.C. system is usually 600 to 750 V.

The steel used in steel cored conductors is usually (a) alloy steel (b) stainless steel (c) mild steel (d) high speed steel (e) all of the above

Description : The steel used in steel cored conductors is usually (a) alloy steel (b) stainless steel (c) mild steel (d) high speed steel (e) all of the above

Last Answer : (c) mild steel

Why does surge impedance loading (SIL) increase with increase in voltage level?

Description : Why does surge impedance loading (SIL) increase with increase in voltage level?

Last Answer : Answer: SIL varies as the square of the operating voltage, so SIL increases with increase in voltage level

Electro-mechanical voltage regulators are generally used in (a) reactors (b) generators (c) transformers (d) all of the above

Description : Electro-mechanical voltage regulators are generally used in (a) reactors (b) generators (c) transformers (d) all of the above

Last Answer : (b) generators

When an alternator connected to the bus-bar is shut down the bus-bar voltage will (a) fall (b) rise (c) remain unchanged (d) none of the above

Description : When an alternator connected to the bus-bar is shut down the bus-bar voltage will (a) fall (b) rise (c) remain unchanged (d) none of the above

Last Answer : (c) remain unchanged

The frequency of voltage generated, in case of generators, can be increased by (a) using reactors (b) increasing the load (c) adjusting the governor (d) reducing the terminal voltage (e) none of the above

Description : The frequency of voltage generated, in case of generators, can be increased by (a) using reactors (b) increasing the load (c) adjusting the governor (d) reducing the terminal voltage (e) none of the above

Last Answer : (c) adjusting the governor

When the interconnector between two stations has large reactance (a) the transfer of power will take place with voltage fluctuation and noise (b) the transfer of power will take place with least loss (c) the stations will fall out of step be¬cause of large angular displacement between the stations (d) none of the above

Description : When the interconnector between two stations has large reactance (a) the transfer of power will take place with voltage fluctuation and noise (b) the transfer of power will take place with least loss ... out of step be¬cause of large angular displacement between the stations (d) none of the above

Last Answer : (c) the stations will fall out of step be¬cause of large angular displacement between the stations

For transmission of power over a distance of 500 km, the transmission voltage should be in the range (a) 150 to 220 kV (b) 100 to 120 kV (c) 60 to 100 kV (d) 20 to 50 kV

Description : For transmission of power over a distance of 500 km, the transmission voltage should be in the range (a) 150 to 220 kV (b) 100 to 120 kV (c) 60 to 100 kV (d) 20 to 50 kV

Last Answer : (a) 150 to 220 kV

Constant voltage transmission entails the following disadvantage (a) large conductor area is required for same power transmission (b) short-circuit current of the system is increased (c) either of the above (d) none of the above

Description : Constant voltage transmission entails the following disadvantage (a) large conductor area is required for same power transmission (b) short-circuit current of the system is increased (c) either of the above (d) none of the above

Last Answer : (b) short-circuit current of the system is increased

In a tap changing transformer, the tappings are provided on (a) primary winding (b) secondary winding (c) high voltage winding (d) any of the above

Description : In a tap changing transformer, the tappings are provided on (a) primary winding (b) secondary winding (c) high voltage winding (d) any of the above

Last Answer : (b) secondary winding

Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer

Description : Which of the following equipment, for regulating the voltage in distribution feeder, will be most economical ? (a) Static condenser (b) Synchronous condenser (c) Tap changing transformer (d) Booster transformer

Last Answer : (d) Booster transformer

For transmission of power over a distance of 200 km, the transmission voltage should be (a) 132 kV (b) 66 kV (c) 33 kV (d) 11 kV

Description : For transmission of power over a distance of 200 km, the transmission voltage should be (a) 132 kV (b) 66 kV (c) 33 kV (d) 11 kV

Last Answer : (a) 132 kV

The voltage drop, for constant voltage transmission is compensated by installing (a) inductors (b) capacitors (c) synchronous motors (d) all of above (e) none of the above

Description : The voltage drop, for constant voltage transmission is compensated by installing (a) inductors (b) capacitors (c) synchronous motors (d) all of above (e) none of the above

Last Answer : (c) synchronous motors

By which of the following a bus-bar is rated ? (a) Current only (b) Current and voltage (c) Current, voltage and frequency (d) Current, voltage, frequency and short time current

Description : By which of the following a bus-bar is rated ? (a) Current only (b) Current and voltage (c) Current, voltage and frequency (d) Current, voltage, frequency and short time current

Last Answer : (d) Current, voltage, frequency and short time current

Transmission voltage of ll kV is normally used for distances upto (a) 20—25 km (b) 40—50 km (c) 60—70 km (d) 80—100 km

Description : Transmission voltage of ll kV is normally used for distances upto (a) 20—25 km (b) 40—50 km (c) 60—70 km (d) 80—100 km

Last Answer : (a) 20—25 km

The power transmitted will be maximum when (a) corona losses are minimum (b) reactance is high (c) sending end voltage is more (d) receiving end voltage is more

Description : The power transmitted will be maximum when (a) corona losses are minimum (b) reactance is high (c) sending end voltage is more (d) receiving end voltage is more

Last Answer : (c) sending end voltage is more

As compared to a 2-wire D.C. distributor, a 3-wire distributor with same maximum voltage to earth uses only (a) 31.25 percent of copper (b) 33.3 percent of copper (c) 66.7 percent of copper (d) 125 percent of copper

Description : As compared to a 2-wire D.C. distributor, a 3-wire distributor with same maximum voltage to earth uses only (a) 31.25 percent of copper (b) 33.3 percent of copper (c) 66.7 percent of copper (d) 125 percent of copper

Last Answer : (a) 31.25 percent of copper

Transmitted power remaining the same, if supply voltage of a D.C. 2-wire feeder is increased 100 percent, saving in copper is (a) 25 percent (b) 50 percent (c) 75 percent (d) 100 percent

Description : Transmitted power remaining the same, if supply voltage of a D.C. 2-wire feeder is increased 100 percent, saving in copper is (a) 25 percent (b) 50 percent (c) 75 percent (d) 100 percent

Last Answer : (b) 50 percent

The material generally used for armour of high voltage cables is (a) aluminium (b) steel (c) brass (d) copper

Description : The material generally used for armour of high voltage cables is (a) aluminium (b) steel (c) brass (d) copper

Last Answer : (b) steel

The material commonly used for insulation in high voltage cables is (a) lead (b) paper (c) rubber (d) none of the above

Description : The material commonly used for insulation in high voltage cables is (a) lead (b) paper (c) rubber (d) none of the above

Last Answer : (b) paper

High voltage transmission lines use (a) suspension insulators (b) pin insulators (c) both (a) and (b) (d) none of the above

Description : High voltage transmission lines use (a) suspension insulators (b) pin insulators (c) both (a) and (b) (d) none of the above

Last Answer : (a) suspension insulators

Most of the high voltage transmission lines in India are (a) underground (b) overhead (c) either of the above (d) none of the above

Description : Most of the high voltage transmission lines in India are (a) underground (b) overhead (c) either of the above (d) none of the above

Last Answer : (b) overhead

The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Description : The voltage of the single phase supply to residential consumers is (a) 110 V (b) 210 V (c) 230 V (d) 400 V

Last Answer : (c) 230 V

Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at the line terminals (c) Possibility of better protection for the line due to possible use of higher terminal reactants (d) Improvement of power factor at times of moderate and heavy loads (e) Possibility of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Description : Which of the following is the demerit of a 'constant voltage transmission system' ? (a) Increase of short-circuit current of the system (b) Availability of steady voltage at all loads at ... of carrying increased power for a given conductor size in case of long-distance heavy power transmission

Last Answer : (a) Increase of short-circuit current of the system

The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Description : The phenomenon qf rise in voltage at the receiving end of the open-circuited or lightly loaded line is called the (a) Seeback effect (b) Ferranti effect (c) Raman effect (d) none of the above

Last Answer : (b) Ferranti effect

How to buy a voltage stabilizer correctly?

Description : How to buy a voltage stabilizer correctly?

Last Answer : How to buy a voltage stabilizer correctly? By the type of networks, stabilizers can be divided into single-phase, designed for a voltage of 220V and three-phase, which are designed for 380V. ... , they must be easy to operate, have a convenient appearance, and not create noise during operation.

List standard voltage level used in India.

Description : List standard voltage level used in India. 

Last Answer : Standard voltage level used in India: * Generation Voltage : 3.3KV, 6.6KV,11KV and 17.5 KV,21KV (Now a days generation voltage is in the range of 11KV- 33KV) * Primary Transmission voltage :- 220 ... voltages in India are 765 KV (750KV), 400KV, 220KV, 132KV, 110KV, 66KV, 33KV, 22KV, 11KV.

State the advantages of use of high voltage in transmission of Electric power.

Description : State the advantages of use of high voltage in transmission of Electric power. 

Last Answer : Advantages: 1. As Transmission voltage increases, current decreases. 2. As current decreases, cross section of conductor decreases. 3. As cross section of conductor decreases, its ... high voltage transmission line, successful interconnection of transmission line is possible than low voltage. 

Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life.

Description : Analyze the effect of supply voltage on performance of LED as regards current, Lumen output, efficacy and life. 

Last Answer : 1) Effect on Current:- In LED current depends upon supply voltage, if voltage get changes then current also change but this change in current will be control by resistors which are connected in series.  2) ...   4) Effect on Life:- If supply voltage is not stable then life of LED get reduced. 

With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Description : With the help of N-channel JFET describe the effect of input voltage VGS on output current ID.

Last Answer : Working of N channel FET: * When a voltage is applied between the drain and source with a DC supply (VDD), the electrons flows from source to drain through narrow channel ... where the channel gets completely blocked and the drain current becomes zero is called pinch- off voltage. 

Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Description : Define: i) Input Offset Voltage ii) Input offset Current iii) Input Bias Current iv) Output offset voltage

Last Answer : Definition of parameters of OPAMP is follows:  i) Input Offset Voltage: Input offset voltage is defined as the voltage that must be applied between the two input terminals of an OPAMP to null or ... to ground) and output voltage is obtained non zero such voltage is output offset voltage of opamp.