In the extraction of copper, the slag formed in the blast furnace is

In the extraction of copper, the slag formed in the blast furnace is
by

1 Answer

Answer :

In the extraction of copper, the slag formed in the blast furnace is A. `CaSiO_(3)` B. `FeSiO_(3)` C. `FeSiO_(3)` D. `MnSiO_(3)`
by
selected by

Related questions

The slag formed in the blast furnace during the extraction of iron from haematite is

Description : The slag formed in the blast furnace during the extraction of iron from haematite is

Last Answer : The slag formed in the blast furnace during the extraction of iron from haematite is A. `Ca_(3)(PO_(4))_(2)` ... (3)` C. `FeSiO_(3)` D. `MnSiO_(3)`

In the extraction of copper the smelt formed in the blast furnace contians

Description : In the extraction of copper the smelt formed in the blast furnace contians

Last Answer : In the extraction of copper the smelt formed in the blast furnace contians A. `CuS+"little"FeS` B. `Cu_(2) ... )O+"little"FeS` D. `Cu_(2)O+"little"FeO

Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and then smelted in a blast furnace. The matt

Description : Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and then smelted in a blast furnace. The matt

Last Answer : Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and ... D. `Cu_(2)O +FeO`(large amount).

Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and then smelted in a blast furnace. The matt

Description : Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and then smelted in a blast furnace. The matt

Last Answer : Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and then ... CaSiO_(3)` D. `Cu_(2)O.SiO_(2)`

Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and then smelted in a blast furnace. The matt

Description : Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and then smelted in a blast furnace. The matt

Last Answer : Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and ... (3)` D. To check the reduction of FeO

Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and then smelted in a blast furnace. The matt

Description : Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and then smelted in a blast furnace. The matt

Last Answer : Extraction of copper is done using copper pyrites. After roasting, the ore is mixed with silica and coke and then ... O` D. `CuCO_(3).Cu(OH)_(2)`

The chemical composition of slag formed during the smelting process in the extraction of copper is :-

Description : The chemical composition of slag formed during the smelting process in the extraction of copper is :-

Last Answer : The chemical composition of slag formed during the smelting process in the extraction of copper is :- A. `Cu_(2)O+ ... C. `CuFeS_(2)` D. `Cu_(2)S+FeO`

The chemical composition of slag formed during the smelting process in the extraction of copper is :-

Description : The chemical composition of slag formed during the smelting process in the extraction of copper is :-

Last Answer : The chemical composition of slag formed during the smelting process in the extraction of copper is :- A. `Cu_(2)O+ ... C. `CuFeS_(2)` D. `Cu_(2)S+FeO`

The chemical composition of slag formed during the smelting process in the extraction of copper is :-

Description : The chemical composition of slag formed during the smelting process in the extraction of copper is :-

Last Answer : The chemical composition of slag formed during the smelting process in the extraction of copper is :- A. `Cu_(2)O+ ... . `CuFeS_(2)` D. `Cu_(2)S++FeO`

What is the viscosity of slag of blast furnace?

Description : What is the viscosity of slag of blast furnace?

Last Answer : What is the answer ?

High ash containing coke (A) Produces more slag when used in the blast(B) Has poor strength and abrasion resistance(C) Is desirable in producer gas manufacture(D) None of these furnace

Description : High ash containing coke (A) Produces more slag when used in the blast furnace (B) Has poor strength and abrasion resistance (C) Is desirable in producer gas manufacture (D) None of these

Last Answer : (A) Produces more slag when used in the blast furnace

Pick out the wrong statement. (A) Dry process is used for the manufacture of cement, when the raw material is blast furnace slag (B) Portland cement is made employing wet process (C) Gypsum is added to Portland cement to lengthen its setting time (D) None of these

Description : Pick out the wrong statement. (A) Dry process is used for the manufacture of cement, when the raw material is blast furnace slag (B) Portland cement is made employing wet process (C) Gypsum is added to Portland cement to lengthen its setting time (D) None of these

Last Answer : (D) None of these

Specific gravity of hot metal (pig iron) is __________ times that of the blast furnace slag. (A) 2 (B) 3 (C) 0.8 (D) 6

Description : Specific gravity of hot metal (pig iron) is __________ times that of the blast furnace slag. (A) 2 (B) 3 (C) 0.8 (D) 6

Last Answer : (B) 3

Most of the phosphorous present in the blast furnace burden enters into (A) Hot metal (B) Flue gases (C) Slag (D) Refractory lining

Description : Most of the phosphorous present in the blast furnace burden enters into (A) Hot metal (B) Flue gases (C) Slag (D) Refractory lining

Last Answer : (A) Hot metal

Limestone is added in the blast furnace (during pig iron manufacture) to (A) Form slag by combining with impurities (B) Supply heat by undergoing exothermic reaction with impurities (C) Reduce the coke consumption (D) Reduce slag viscosity

Description : Limestone is added in the blast furnace (during pig iron manufacture) to (A) Form slag by combining with impurities (B) Supply heat by undergoing exothermic reaction with impurities (C) Reduce the coke consumption (D) Reduce slag viscosity

Last Answer : Option A

Volume of blast furnace slag is about __________ times the volume of hot metal (pig iron) of the same weight (A) 1.5 (B) 3 (C) 5

Description : Volume of blast furnace slag is about __________ times the volume of hot metal (pig iron) of the same weight (A) 1.5 (B) 3 (C) 5

Last Answer : Option B

Basicity [%Cao + %MgO + %SiO2) of the slag in Indian blast furnace is in the range of (A) 0.7-1.0 (B) 1.1-1.4 (C) 1.5 - 1.8

Description : Basicity [%Cao + %MgO + %SiO2) of the slag in Indian blast furnace is in the range of (A) 0.7-1.0 (B) 1.1-1.4 (C) 1.5 - 1.8

Last Answer : Option B

You are asked to construct a massive dam, the type of cement you will use, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Description : You are asked to construct a massive dam, the type of cement you will use, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Last Answer : Answer: Option C

For the construction of thin R.C.C. structures, the type of cement to be avoided, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Description : For the construction of thin R.C.C. structures, the type of cement to be avoided, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Last Answer : Answer: Option D

For road pavements, the cement generally used, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Description : For road pavements, the cement generally used, is (A) Ordinary Portland cement (B) Rapid hardening cement (C) Low heat cement (D) Blast furnace slag cement

Last Answer : Answer: Option B

Blast furnace slag cement concrete requires ___________time for shuttering and curing. (a) Less (b) More (c) Medium (d) All the above

Description : Blast furnace slag cement concrete requires ___________time for shuttering and curing. (a) Less (b) More (c) Medium (d) All the above

Last Answer : (b) More

For mass concrete work, the type of cement preferable is [ A ] Ordinary Portland cement [ B ] Rapid hardening cement [ C ] Low heat cement [ D ] Blast furnace slag cement

Description : For mass concrete work, the type of cement preferable is [ A ] Ordinary Portland cement [ B ] Rapid hardening cement [ C ] Low heat cement [ D ] Blast furnace slag cement

Last Answer : [ C ] Low heat cement

For road pavements, the cement generally used, is [ A ] Ordinary Portland cement [ B ] Rapid hardening cement [ C ] Low heat cement [ D ] Blast furnace slag cement

Description : For road pavements, the cement generally used, is [ A ] Ordinary Portland cement [ B ] Rapid hardening cement [ C ] Low heat cement [ D ] Blast furnace slag cement

Last Answer : [ A ] Ordinary Portland cement

In Portland Blast furnace slag cement, the blast furnace slag content shall not exceed [ A ] 50% [ B ] 65% [ C ] 80% [ D ] 90%

Description : In Portland Blast furnace slag cement, the blast furnace slag content shall not exceed [ A ] 50% [ B ] 65% [ C ] 80% [ D ] 90%

Last Answer : [ B ] 65%

State the uses of fly ash and blast furnace slag.

Description : State the uses of fly ash and blast furnace slag.

Last Answer :  I) Fly ash The various uses of fly ash are: 1) Concrete production, as a partial substitute material for Portland cement. 2) For the construction of embankments and other structural fills. 3) For ... and water proofing. 5) It is used as insulation in mineral wool, in rail road ballast etc.

Write two uses of each : (i) Fly ash (ii) Blast furnace slag

Description : Write two uses of each : (i) Fly ash (ii) Blast furnace slag

Last Answer : I) Fly ash The various uses of fly ash are: 1) Concrete production, as a partial substitute material for Portland cement. 2) For the construction of embankments and other structural fills. 3) For ... and water proofing. 5) It is used as insulation in mineral wool, in rail road ballast etc. 

During the extraction of iron in the blast furnace ,

Description : During the extraction of iron in the blast furnace ,

Last Answer : During the extraction of iron in the blast furnace , A. Coke acts as reducing agent in the lower ... and Coke acts as reducing agent in the upper zone

In the extraction of iron in the blast furnace, the reducing agent for the ore is

Description : In the extraction of iron in the blast furnace, the reducing agent for the ore is

Last Answer : In the extraction of iron in the blast furnace, the reducing agent for the ore is A. Carbon monoxide B. Carbon dioxide C. Carbon D. Silica

The main reactions occuring in blast furnace during extraction of iron from haematite ore…..

Description : The main reactions occuring in blast furnace during extraction of iron from haematite ore…..

Last Answer : The main reactions occuring in blast furnace during extraction of iron from haematite ore .. A. `Fe_(2)O_ ... 3Cto2Fe+3CO` D. `CaO+SiO_(2)toCaSiO_(2)`

The flux used in the extraction of iron from Haematite in te blast furnace is `"["EAM(ENG)2014"]"`

Description : The flux used in the extraction of iron from Haematite in te blast furnace is `"["EAM(ENG)2014"]"`

Last Answer : The flux used in the extraction of iron from Haematite in te blast furnace is `"["EAM(ENG)2014"]"` A. Lime stone B. Silica C. Coke D. CO

__________ is used as a flux in the extraction of iron from iron ore (haematite) in blast furnace. (A) Bauxite (B) Limestone (C) Quartz (D) Manganese

Description : __________ is used as a flux in the extraction of iron from iron ore (haematite) in blast furnace. (A) Bauxite (B) Limestone (C) Quartz (D) Manganese

Last Answer : (B) Limestone

When copper pyrites is roasted in excess of air, a mixture of `CuO + FeO` is formed. `FeO` is present as impurity. This can be removed as slag during

Description : When copper pyrites is roasted in excess of air, a mixture of `CuO + FeO` is formed. `FeO` is present as impurity. This can be removed as slag during

Last Answer : When copper pyrites is roasted in excess of air, a mixture of `CuO + FeO` is formed. `FeO` is present ... a basic flux D. CaO, which is a basic flux

The iron formed in blast furnace is calle d

Description : The iron formed in blast furnace is calle d

Last Answer : The iron formed in blast furnace is calle d A. Pig iron B. Wrought iron C. Steel D. Cast iron

The cement whose strength is a little lower than the ordinary cement during the first three months but attains afterwards the same strength, is known as (A) Low-heat Portland cement (B) Rapid hardening Portland cement (C) Portland blast slag cement (D) Portland pozzolana cement

Description : The cement whose strength is a little lower than the ordinary cement during the first three months but attains afterwards the same strength, is known as (A) Low-heat Portland cement (B) Rapid hardening Portland cement (C) Portland blast slag cement (D) Portland pozzolana cement

Last Answer : Answer: Option A

During the extraction of iron, slag produced is

Description : During the extraction of iron, slag produced is

Last Answer : During the extraction of iron, slag produced is A. Zone of heat absorption B. Zone of reduction only ... only D. Zone of reduction and zone of fusion

How is the slag obtained in the extraction of iron useful?

Description : How is the slag obtained in the extraction of iron useful?

Last Answer : Slag obtained in blast furnace is used as one of theraw materials of glass and cement.

Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore? (A) High fusibility & fluidity (B) High thermal conductivity (C) Low density (D) High chemical activity

Description : Which of the following is an undesirable property of slag produced during the Pyrometallurgical method of metal extraction from its ore? (A) High fusibility & fluidity (B) High thermal conductivity (C) Low density (D) High chemical activity

Last Answer : B) High thermal conductivity

The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag. (A) Fluidity (B) Basicity (C) Acidity (D) Viscosity

Description : The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag. (A) Fluidity (B) Basicity (C) Acidity (D) Viscosity

Last Answer : Option A

The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag. (A) Fluidity (B) Basicity (C) Acidity (D) Viscosity

Description : The function of neutral flux used in the pyrometallurgy of metal extraction is to increase the __________ of the slag. (A) Fluidity (B) Basicity (C) Acidity (D) Viscosity

Last Answer : Option A

Which furnace burns low-ash fusion coal and retains most of the coal ash in the slag?

Description : Which furnace burns low-ash fusion coal and retains most of the coal ash in the slag?

Last Answer : Cyclone furnace.

Low grade phosphate rock can be used in electrical furnace, because (A) Of the better CaO/SiO2 balance for slag formation (B) CaO content is less (C) It is cheap (D) It produces low cost product

Description : Low grade phosphate rock can be used in electrical furnace, because (A) Of the better CaO/SiO2 balance for slag formation (B) CaO content is less (C) It is cheap (D) It produces low cost product

Last Answer : (A) Of the better CaO/SiO2 balance for slag formation

furnace slag is mainly molten (A) Sand (B) Magnesium silicate (C) Calcium silicate (D) Iron pyrite

Description : furnace slag is mainly molten (A) Sand (B) Magnesium silicate (C) Calcium silicate (D) Iron pyrite

Last Answer : Option C

Which cement should not be used for bridge slabs ro RCC frames a) OPC b) Portland Pozzolana cement * c) Portland furnace slag cement d) Rapid hardening cement

Description : Which cement should not be used for bridge slabs ro RCC frames a) OPC b) Portland Pozzolana cement * c) Portland furnace slag cement d) Rapid hardening cement

Last Answer : b) Portland Pozzolana cement *

5. In "Imperial Smelting Process" for extraction of zinc, zinc vapour thus produced is quenched in the external condenser by the use of the following: (A) Jet of water at high pressure (B) Blast of air (C) Mixture of water and air (D) Rain of molten lead

Description : 5. In "Imperial Smelting Process" for extraction of zinc, zinc vapour thus produced is quenched in the external condenser by the use of the following: (A) Jet of water at high pressure (B) Blast of air (C) Mixture of water and air (D) Rain of molten lead

Last Answer : Option D

In the metallurgy of iron, when limestone is added to the blast furnace,the calcium ions end up in

Description : In the metallurgy of iron, when limestone is added to the blast furnace,the calcium ions end up in

Last Answer : In the metallurgy of iron, when limestone is added to the blast furnace,the calcium ions end up ... B. Gangue C. Metallic calcium D. Calcium Carbonate

Near the top of the blast furnace, iron oxides are reduced to …… by carbon monoxide .

Description : Near the top of the blast furnace, iron oxides are reduced to …… by carbon monoxide .

Last Answer : Near the top of the blast furnace, iron oxides are reduced to …… by carbon monoxide . A. C B. CO C. `CO_(2)` D. `CaCO_(3)`

A mixture of haematite, coke and limestone on heating in blast furnace gives molten iron metal. This is known as

Description : A mixture of haematite, coke and limestone on heating in blast furnace gives molten iron metal. This is known as

Last Answer : A mixture of haematite, coke and limestone on heating in blast furnace gives molten iron metal. ... Smelting B. Calcination C. Roasting D. Liquition

In the metallurgy of Fe, when `CaCo_(3)` is added to blast furnace, calcicum ion appears as

Description : In the metallurgy of Fe, when `CaCo_(3)` is added to blast furnace, calcicum ion appears as

Last Answer : In the metallurgy of Fe, when `CaCo_(3)` is added to blast furnace, calcicum ion appears as A. CaO B. metallic C. ggangue D. slag

What is top pressure in blast furnace?

Description : What is top pressure in blast furnace?

Last Answer : What is the answer ?